Po nějaké delší době a po upgrade systému na Lubuntu 16.04 ze 14.04 jsem se pokoušel vypálit nějaké datové soubory na CD s použitím programu K3B. Skončilo to podivnou chybou Error 254. Pokusil jsem ještě programy Brasero a Nero Linux, stále bez úspěchu. Zkoušel jsem totéž na jiném svém počítači bohužel se stejným systémem, také neúspěšně. Výpis chyb z K3b vypadá např. takto:
Devices
-----------------------
HL-DT-ST DVDRAM GSA-4167B DL11 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite] [%7]
K3b::IsoImager
-----------------------
mkisofs print size result: 1290 (2641920 bytes)
System
-----------------------
K3b Version: 2.0.3
KDE Version: 4.14.16
QT Version: 4.8.7
Kernel: 4.4.0-124-generic
Used versions
-----------------------
mkisofs: 1.1.11
cdrecord: 3.2a09
cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
cdrecord: Warning: DMA resid 0 for 'read buffer', actual data is too short.
cdrecord: Warning: The DMA speed test has been skipped.
Cdrecord-ProDVD-ProBD-Clone 3.02a09 (i686-pc-linux-gnu) Copyright (C) 1995-2016 Joerg Schilling
TOC Type: 3 = CD-ROM XA mode 2
Using libscg version 'schily-0.9'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identifikation : 'DVDRAM GSA-4167B'
Revision : 'DL11'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: CD-RW
Profile: DVD-RAM
Profile: DVD-R sequential recording
Profile: DVD-R/DL sequential recording
Profile: DVD-R/DL layer jump recording
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD+RW
Profile: DVD+R
Profile: DVD+R/DL
Profile: DVD-ROM
Profile: CD-R
Profile: CD-RW (current)
Profile: CD-ROM
Profile: Removable Disk
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive pbuf size: 1966080 = 1920 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 2 MB
Total size: 2 MB (00:17.22) = 1292 sectors
Lout start: 3 MB (00:19/17) = 1292 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 2
Reference speed: 6
Disk Is not unrestricted
Disk Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11077 (97:34/23)
ATIP start of lead out: 359849 (79:59/74)
1T speed low: 4 1T speed high: 10
2T speed low: 2 2T speed high: 10
power mult factor: 2 6
recommended erase/write power: 5
A1 values: 24 2C DC
A2 values: 14 A4 4A
A3 values: 04 C4 80
Disk type: Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Capacity Blklen/Sparesz. Format-type Type
0 2048 0x00 No Media Present or Unknown Capacity
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 358557
Starting to write CD/DVD/BD at speed 10 in real TAO mode for multi session.
Last chance to quit, starting real write in 3 seconds.
2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Performing OPC...
Starting new track at sector: 0
Track 01: 0 of 2 MB written.
cdrecord: Chyba vstupu/výstupu. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 00 3E 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 10 DF B5 60 90 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.008s timeout 40s
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
write track data: error after 126976 bytes
Writing time: 11.440s (00:00:11.440)
Average write speed 1,5x.
Fixating...
Fixating time: 33.148s (00:00:33.148)
cdrecord: fifo had 42 puts and 3 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/sr0 speed=10 -tao driveropts=burnfree -multi -xa -tsize=1290s -
mkisofs
-----------------------
1290
I: -input-charset not specified, using utf-8 (detected in locale settings)
39.61% done, estimate finish Tue May 15 11:53:51 2018
78.06% done, estimate finish Tue May 15 11:53:50 2018
Total translation table size: 0
Total rockridge attributes bytes: 263
Total directory bytes: 390
Path table size(bytes): 10
Max brk space used 0
1290 extents written (2 MB)
mkisofs calculate size command:
-----------------------
/usr/bin/genisoimage -gui -graft-points -print-size -quiet -volid Basin Street Blues -volset -appid K3B THE CD KREATOR (C) 1998-2010 SEBASTIAN TRUEG AND MICHAL MALEK -publisher -preparer -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-jan/k3bV21787.tmp -rational-rock -hide-list /tmp/kde-jan/k3bw21787.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-jan/k3bU21787.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 3 -path-list /tmp/kde-jan/k3bN21787.tmp
mkisofs command:
-----------------------
/usr/bin/genisoimage -gui -graft-points -volid Basin Street Blues -volset -appid K3B THE CD KREATOR (C) 1998-2010 SEBASTIAN TRUEG AND MICHAL MALEK -publisher -preparer -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-jan/k3bR21787.tmp -rational-rock -hide-list /tmp/kde-jan/k3bw21787.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-jan/k3bJ21787.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 3 -path-list /tmp/kde-jan/k3by21787.tmp
--------------------------------------------------------------------------------------------------
Nemáte s tím někdo podobné zkušenosti, co s tím? Přitom čtení z CD/DVD jde v obou případech bezchybně, takže jednotkou CD/DVD to asi nebude. Zapisoval jsem v obou případech na CD-R nebo CD-RW značky Verbatim.
HW konfigurace stroje je tato:
Intel Pentium j2900
2x4GiB DDIM DDR3 133 MHz
systémový SCSI disk 120GB Kingston
přídavný 80GB HDD IDE přes IDE controller
DVDRAM GSA-4167B