Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Internet a sítě => Téma založeno: apin 27 Března 2013, 12:00:21
-
Zdravím odborníky. Potřebuji trochu nasměrovat, kde pátrat, proč se mi ntb po uspání do paměti a následném probuzení nechce připojit k wi-fi síti, ke které byl předtím normálně připojen..
Mám DELL Vostro 1220 a po zkoušení mnoha jiných distribucí, kde tento problém nebyl, jsem zakotvil na Ubuntu 12.04 LTS a doinstaloval Gnome shell (Unity mi moc nesedí).
Ze začátku s tímhle problém nebyl a mám ten pocit, že ani nevyšla žádná aktualizace, která by to mohla způsobovat, prostě mi to znenadání přestalo fungovat...
Zkoušel jsem i vyhodit nm a teď se připojuji čistě jen přes wicd, po čistém restartu se připojí bez problémů takřka okamžitě, po uspání vypíše bad password (ačkoli je zadané správně).
Poradí někdo co s tím?
výpis ifconfig před uspáním :
eth0 Link encap:Ethernet HWadr 00:26:b9:05:ab:8a
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST MTU:1500 Metrika:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)
Přerušení:45 Vstupně/Výstupní port:0xe000
eth2 Link encap:Ethernet HWadr 70:1a:04:2c:38:3a
inet adr:192.168.2.24 Všesměr:192.168.2.255 Maska:255.255.255.0
inet6-adr: fe80::721a:4ff:fe2c:383a/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:70665 errors:0 dropped:0 overruns:0 frame:41788
TX packets:57835 errors:9 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 92852610 (92.8 MB) Odesláno bajtů: 5619555 (5.6 MB)
Přerušení:17 Vstupně/Výstupní port:0xc000
lo Link encap:Místní smyčka
inet adr:127.0.0.1 Maska:255.0.0.0
inet6-adr: ::1/128 Rozsah:Počítač
AKTIVOVÁNO SMYČKA BĚŽÍ MTU:16436 Metrika:1
RX packets:2467 errors:0 dropped:0 overruns:0 frame:0
TX packets:2467 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 280795 (280.7 KB) Odesláno bajtů: 280795 (280.7 KB)
lxcbr0 Link encap:Ethernet HWadr 86:13:b2:87:9c:2a
inet adr:10.0.3.1 Všesměr:10.0.3.255 Maska:255.255.255.0
inet6-adr: fe80::8413:b2ff:fe87:9c2a/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:346 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 50079 (50.0 KB)
a iwconfig:
lo no wireless extensions.
eth2 IEEE 802.11abg ESSID:"home"
Mode:Managed Frequency:2.462 GHz Access Point: 00:02:72:6F:3A:F7
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
eth0 no wireless extensions.
lxcbr0 no wireless extensions.
po uspání a probuzení se musím připojit kabelem a píše to toto:
eth0 Link encap:Ethernet HWadr 00:26:b9:05:ab:8a
inet adr:10.0.0.2 Všesměr:10.0.0.255 Maska:255.255.255.0
inet6-adr: 2a00:1028:83d0:1a82:ad13:f0d5:bbe1:a944/64 Rozsah:Globál
inet6-adr: 2a00:1028:83d0:1a82:226:b9ff:fe05:ab8a/64 Rozsah:Globál
inet6-adr: fe80::226:b9ff:fe05:ab8a/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:235 errors:0 dropped:0 overruns:0 frame:0
TX packets:328 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 66737 (66.7 KB) Odesláno bajtů: 57951 (57.9 KB)
Přerušení:45 Vstupně/Výstupní port:0xe000
eth2 Link encap:Ethernet HWadr 70:1a:04:2c:38:3a
inet6-adr: fe80::721a:4ff:fe2c:383a/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST MTU:1500 Metrika:1
RX packets:73178 errors:0 dropped:0 overruns:0 frame:43143
TX packets:60113 errors:51 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 94967287 (94.9 MB) Odesláno bajtů: 5979024 (5.9 MB)
Přerušení:17 Vstupně/Výstupní port:0xc000
lo Link encap:Místní smyčka
inet adr:127.0.0.1 Maska:255.0.0.0
inet6-adr: ::1/128 Rozsah:Počítač
AKTIVOVÁNO SMYČKA BĚŽÍ MTU:16436 Metrika:1
RX packets:3973 errors:0 dropped:0 overruns:0 frame:0
TX packets:3973 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 400028 (400.0 KB) Odesláno bajtů: 400028 (400.0 KB)
lxcbr0 Link encap:Ethernet HWadr 86:13:b2:87:9c:2a
inet adr:10.0.3.1 Všesměr:10.0.3.255 Maska:255.255.255.0
inet6-adr: fe80::8413:b2ff:fe87:9c2a/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:398 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 56743 (56.7 KB)
iwconfig:
lo no wireless extensions.
eth2 IEEE 802.11abg ESSID:"home"
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
eth0 no wireless extensions.
lxcbr0 no wireless extensions.
je to problém u jakékoli sítě, nejenom u té mojí. díky za každou radu
-
ukaz nam prosim vystup z:
dmesg | egrep -i eth2\|wireless
samozrejme po probuzeni, az budes reprodukovat tento problem ..
me to v podstate dela taky, ale nevadi mi to, protoze nepouzivam network managera, kterej netusim, jak se umi vyporadat s resetem usb (wifiny jsou interne na usb) .. ja proste restartuju to spojeni - tedy kdyz dam uspat pripojenej, tak po probuzeni vypnu/zapnu spojeni a jede to dal
-
Tak tady po čistémm restartu když se to připojí samo:
apin@apin-Vostro-1220:~$ dmesg | egrep -i eth2\|wireless
[ 3.108255] input: KYE Systems Corp. Wireless Keyboard & Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/input/input4
[ 3.108401] generic-usb 0003:0458:0049.0001: input,hidraw0: USB HID v1.10 Keyboard [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:1d.1-2/input0
[ 3.133684] input: KYE Systems Corp. Wireless Keyboard & Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.1/input/input5
[ 3.133841] generic-usb 0003:0458:0049.0002: input,hidraw1: USB HID v1.10 Mouse [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:1d.1-2/input1
[ 23.873438] eth1: Broadcom BCM4315 802.11 Hybrid Wireless Controller 6.20.155.1 (r326264)
[ 24.088613] udevd[498]: renamed network interface eth1 to eth2
[ 37.664022] eth2: no IPv6 routers present
po uspání a probuzení se samozřejmě odmítá připojit:
apin@apin-Vostro-1220:~$ dmesg | egrep -i eth2\|wireless
[ 3.108255] input: KYE Systems Corp. Wireless Keyboard & Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/input/input4
[ 3.108401] generic-usb 0003:0458:0049.0001: input,hidraw0: USB HID v1.10 Keyboard [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:1d.1-2/input0
[ 3.133684] input: KYE Systems Corp. Wireless Keyboard & Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.1/input/input5
[ 3.133841] generic-usb 0003:0458:0049.0002: input,hidraw1: USB HID v1.10 Mouse [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:1d.1-2/input1
[ 23.873438] eth1: Broadcom BCM4315 802.11 Hybrid Wireless Controller 6.20.155.1 (r326264)
[ 24.088613] udevd[498]: renamed network interface eth1 to eth2
[ 37.664022] eth2: no IPv6 routers present
[ 497.537286] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[ 537.143521] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
-
[ 497.537286] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[ 537.143521] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
tak to dela to stejne jako me .. reseni neznam, neb v mem pripade staci jen vypnout/zapnout to spojeni ..
-
Neviem či to k niečomu bude: No wireless connections after sleep/suspend
http://ubuntuforums.org/showthread.php?t=2004690 (http://ubuntuforums.org/showthread.php?t=2004690)
http://www.techytalk.info/ubuntu-fix-network-stopped-working-after-resume-from-sleep/ (http://www.techytalk.info/ubuntu-fix-network-stopped-working-after-resume-from-sleep/)
-
Neviem či to k niečomu bude: No wireless connections after sleep/suspend
http://ubuntuforums.org/showthread.php?t=2004690 (http://ubuntuforums.org/showthread.php?t=2004690)
http://www.techytalk.info/ubuntu-fix-network-stopped-working-after-resume-from-sleep/ (http://www.techytalk.info/ubuntu-fix-network-stopped-working-after-resume-from-sleep/)
Díky za radu, ale v mém případě to nepomohlo :(
[ 497.537286] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[ 537.143521] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
tak to dela to stejne jako me .. reseni neznam, neb v mem pripade staci jen vypnout/zapnout to spojeni ..
To mě nenapadlo, ale funguje. Jen se bojim, že si tímhle postupem velmi rychle opotřebuji hw vypínač bezdrátové komunikace...
-
podle me to staci delat na urovni NM (Network Managera) - ne hw vypinacem .. proste zapni/vypni wifi adapter .. ma to tam zaskrtavatko
-
Nepomohlo by ani automatizovať to skiptom po prebudení?
http://fooninja.net/2010/09/02/how-to-fix-wifi-after-suspendresume-in-ubuntu/ (http://fooninja.net/2010/09/02/how-to-fix-wifi-after-suspendresume-in-ubuntu/)
-
Neviem či to k niečomu bude: No wireless connections after sleep/suspend
http://ubuntuforums.org/showthread.php?t=2004690 (http://ubuntuforums.org/showthread.php?t=2004690)
http://www.techytalk.info/ubuntu-fix-network-stopped-working-after-resume-from-sleep/ (http://www.techytalk.info/ubuntu-fix-network-stopped-working-after-resume-from-sleep/)
Díky za radu, ale v mém případě to nepomohlo :(
...
Beru zpět. dnes ráno probudím počítač a připojí se ;) Vyzkoušel jsem obě možnosti, takže netuším která zabrala :)
-
Som rád že ti to ide. Pár krát ho ešte preber a ak to funguje, tak edituj predmet prvého postu ako [vyřešeno]
... Vyzkoušel jsem obě možnosti, takže netuším která zabrala :)
Edit: Tá druhá možnosť je pre Realtek xxxx a tvoj je Broadcom BCM4315
-
Tak opět je všechno úplně jinak. Problém bude asi někde jinde.
To první připojení po probuzení bylo při provozu na baterku. Pokud je připojen adaptér, tak wicd zase píše bad password. Zkoušel jsem se vrátit zpátky, promazal soubory z postupů v odkazech výše a začal laborovat.
Chová se to nevyzpytatelně:
Restart systému s adaptérem>wicd se připojí>uspání-probuzení>wicd bad password
Restart systému na baterku>wicd se připojí>uspání-probuzení>wicd se připojí
Restart systému s adaptérem>wicd nenajde žádnou síť>uspání-probuzení>to samé
Restart systému na baterku>wicd nenajde žádnou síť>uspání-probuzení>to samé
Další restart systému s adaptérem>wicd zázračně najde síťě a do té mojí se připojí>uspání-probuzení>wicd bad password.
Restart systému na baterku>wicd se připojí>uspání-probuzení>wicd bad password
Další pokusné restarty a uspávání s adaptérem nebo na baterku se chovají naprosto náhodně. někdy wicd nevidí žádné sítě, jindy zase vidí a připojí se. Po probuzení je nějaká šance na připojení pouze při provozu na baterku...
Jo a jak mi tu radil ntz_reloaded vypnout a zapnout wifi modul, tak to také přestalo účinkovat, jak sw, tak i hw tlačítkem...
A jen tak mimochodem. po probuzení to nechce přihlašovací heslo do desktopu, prostě se probudí do odemčeného desktopu, ačkoli v nastavení to zaškrtunuté mám. Při provozu na baterii to chce heslo zhruba tak jednou za 5 restartů...
Napadá někoho, čím by to mohlo být? Podotýkám, že od Ubuntu 8.10, přes Mint, Fuduntu a jiné distra na tomhle počítači tento problém nikdy nebyl. V biosu jsem taky nic neměnil...
-
Vráť zmeny, ktoré si urobil podľa tých odkazov.
Daj výpis z var/log/pm-suspend.log
jeden keď sa pripojí a druhý keď sa nepripojí
Snáď to niekto rozlúskne.
Edit:aha zmeny si už vrátil :) musím čítať 2x a pozorne ;)
-
Vráť zmeny, ktoré si urobil podľa tých odkazov.
Daj výpis z var/log/pm-suspend.log
jeden keď sa pripojí a druhý keď sa nepripojí
Snáď to niekto rozlúskne.
bash: var/log/pm-suspend.log: Adresář nebo soubor neexistuje
-
gedit /var/log/pm-suspend.log
alebo aj vo var/log/wicd by niečo mohlo byť
-
Díky za trpělivost
takže po čistém restartu se to připojilo ještě než naskočil horní panel:
wicd log je prázdný
pm-suspend.log vypadá takhle:
(nevejde se to sem, tak to házím na dropbox)
https://dl.dropbox.com/u/13067236/pm-suspend_log_pred.txt
uspávám (adaptér zůstává zapojen), probouzím, připojí se. Uspávám tedy znova (adaptér stále připojen), zkouší to asi 3x, ale nepřipojí se...
pm-suspend.log po probuzení vypadá takhle:
https://dl.dropbox.com/u/13067236/pm-suspend_log_po.txt
Hádám, že budou asi rozhodující ty rozdíly ve výpisu, takže sem hodím jen to, co tam podle porovnání souborů přibylo na konci výpisu, ať se tím nemusí případný dobrovolník prohrabávat:
Initial commandline parameters:
Fri Mar 29 13:15:30 CET 2013: Running hooks for suspend.
Running hook /usr/lib/pm-utils/sleep.d/000kernel-change suspend suspend:
/usr/lib/pm-utils/sleep.d/000kernel-change suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00logging suspend suspend:
Linux apin-Vostro-1220 3.2.0-39-generic-pae #62-Ubuntu SMP Wed Feb 27 22:25:11 UTC 2013 i686 i686 i386 GNU/Linux
Module Size Used by
snd_hrtimer 12648 1
ipt_MASQUERADE 12663 1
iptable_nat 13016 1
nf_nat 24959 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 19084 3 iptable_nat,nf_nat
nf_conntrack 73847 4 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 12649 1 nf_conntrack_ipv4
ip_tables 18106 1 iptable_nat
x_tables 22011 3 ipt_MASQUERADE,iptable_nat,ip_tables
bridge 79601 0
stp 12848 1 bridge
snd_hda_codec_conexant 52521 1
btusb 17948 2
dell_wmi 12601 0
sparse_keymap 13658 1 dell_wmi
dell_laptop 17767 0
dcdbas 14098 1 dell_laptop
lib80211_crypt_tkip 17275 0
psmouse 86520 0
wl 2906597 0
uvcvideo 67203 0
videodev 86588 1 uvcvideo
serio_raw 13027 0
joydev 17393 0
parport_pc 32114 0
ppdev 12849 0
bnep 17830 2
rfcomm 38139 16
mac_hid 13077 0
bluetooth 158479 23 btusb,bnep,rfcomm
snd_hda_intel 32719 2
snd_hda_codec 109562 2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 13276 1 snd_hda_codec
cfg80211 178877 1 wl
snd_pcm 80916 2 snd_hda_intel,snd_hda_codec
binfmt_misc 17292 1
lib80211 14040 2 lib80211_crypt_tkip,wl
snd_seq_midi 13132 0
snd_rawmidi 25424 1 snd_seq_midi
i915 423466 3
snd_seq_midi_event 14475 1 snd_seq_midi
snd_seq 51592 3 snd_seq_midi,snd_seq_midi_event
snd_timer 28931 3 snd_hrtimer,snd_pcm,snd_seq
snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq
wmi 18744 1 dell_wmi
snd 62218 14 snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
drm_kms_helper 45466 1 i915
drm 197641 4 i915,drm_kms_helper
soundcore 14635 1 snd
snd_page_alloc 14108 2 snd_hda_intel,snd_pcm
i2c_algo_bit 13199 1 i915
video 19115 1 i915
lp 17455 0
parport 40930 3 parport_pc,ppdev,lp
usbhid 41937 0
hid 77428 1 usbhid
r8169 56368 0
ums_realtek 17920 0
usb_storage 39683 1 ums_realtek
total used free shared buffers cached
Mem: 3062012 1168528 1893484 0 129944 511928
-/+ buffers/cache: 526656 2535356
Swap: 3108540 0 3108540
/usr/lib/pm-utils/sleep.d/00logging suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave suspend suspend:
/usr/lib/pm-utils/sleep.d/00powersave suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01PulseAudio suspend suspend:
Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>>
/usr/lib/pm-utils/sleep.d/01PulseAudio suspend suspend: success.
Running hook /etc/pm/sleep.d/10_grub-common suspend suspend:
/etc/pm/sleep.d/10_grub-common suspend suspend: success.
Running hook /etc/pm/sleep.d/10_unattended-upgrades-hibernate suspend suspend:
/etc/pm/sleep.d/10_unattended-upgrades-hibernate suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend:
Having NetworkManager put all interaces to sleep...Failed.
/usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55wicd suspend suspend:
/usr/lib/pm-utils/sleep.d/55wicd suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend:
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
/usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/75modules suspend suspend:
/usr/lib/pm-utils/sleep.d/75modules suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock suspend suspend:
/usr/lib/pm-utils/sleep.d/90clock suspend suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95anacron suspend suspend:
stop: Unknown instance:
/usr/lib/pm-utils/sleep.d/95anacron suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95hdparm-apm suspend suspend:
/usr/lib/pm-utils/sleep.d/95hdparm-apm suspend suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/95led suspend suspend:
/usr/lib/pm-utils/sleep.d/95led suspend suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend:
Kernel modesetting video driver detected, not using quirks.
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/99video suspend suspend:
kernel.acpi_video_flags = 0
/usr/lib/pm-utils/sleep.d/99video suspend suspend: success.
Running hook /etc/pm/sleep.d/novatel_3g_suspend suspend suspend:
/etc/pm/sleep.d/novatel_3g_suspend suspend suspend: success.
Fri Mar 29 13:15:34 CET 2013: performing suspend
Fri Mar 29 13:15:52 CET 2013: Awake.
Fri Mar 29 13:15:52 CET 2013: Running hooks for resume
Running hook /etc/pm/sleep.d/novatel_3g_suspend resume suspend:
/etc/pm/sleep.d/novatel_3g_suspend resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/99video resume suspend:
/usr/lib/pm-utils/sleep.d/99video resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend:
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95led resume suspend:
/usr/lib/pm-utils/sleep.d/95led resume suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/95hdparm-apm resume suspend:
/dev/sda:
setting Advanced Power Management level to 0xfe (254)
APM_level = 254
/dev/sda:
setting Advanced Power Management level to 0xfe (254)
APM_level = 254
/usr/lib/pm-utils/sleep.d/95hdparm-apm resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95anacron resume suspend:
/usr/lib/pm-utils/sleep.d/95anacron resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock resume suspend:
/usr/lib/pm-utils/sleep.d/90clock resume suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/75modules resume suspend:
Reloaded unloaded modules.
/usr/lib/pm-utils/sleep.d/75modules resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant resume suspend:
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
/usr/lib/pm-utils/sleep.d/60_wpa_supplicant resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55wicd resume suspend:
/usr/lib/pm-utils/sleep.d/55wicd resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend:
Having NetworkManager wake interfaces back up...Failed.
/usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend: success.
Running hook /etc/pm/sleep.d/10_unattended-upgrades-hibernate resume suspend:
/etc/pm/sleep.d/10_unattended-upgrades-hibernate resume suspend: success.
Running hook /etc/pm/sleep.d/10_grub-common resume suspend:
/etc/pm/sleep.d/10_grub-common resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01PulseAudio resume suspend:
Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>>
/usr/lib/pm-utils/sleep.d/01PulseAudio resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave resume suspend:
/usr/lib/pm-utils/sleep.d/00powersave resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00logging resume suspend:
/usr/lib/pm-utils/sleep.d/00logging resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/000kernel-change resume suspend:
/usr/lib/pm-utils/sleep.d/000kernel-change resume suspend: success.
Fri Mar 29 13:15:55 CET 2013: Finished.
Initial commandline parameters:
Fri Mar 29 13:17:02 CET 2013: Running hooks for suspend.
Running hook /usr/lib/pm-utils/sleep.d/000kernel-change suspend suspend:
/usr/lib/pm-utils/sleep.d/000kernel-change suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00logging suspend suspend:
Linux apin-Vostro-1220 3.2.0-39-generic-pae #62-Ubuntu SMP Wed Feb 27 22:25:11 UTC 2013 i686 i686 i386 GNU/Linux
Module Size Used by
snd_hrtimer 12648 1
ipt_MASQUERADE 12663 1
iptable_nat 13016 1
nf_nat 24959 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 19084 3 iptable_nat,nf_nat
nf_conntrack 73847 4 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 12649 1 nf_conntrack_ipv4
ip_tables 18106 1 iptable_nat
x_tables 22011 3 ipt_MASQUERADE,iptable_nat,ip_tables
bridge 79601 0
stp 12848 1 bridge
snd_hda_codec_conexant 52521 1
btusb 17948 2
dell_wmi 12601 0
sparse_keymap 13658 1 dell_wmi
dell_laptop 17767 0
dcdbas 14098 1 dell_laptop
lib80211_crypt_tkip 17275 0
psmouse 86520 0
wl 2906597 0
uvcvideo 67203 0
videodev 86588 1 uvcvideo
serio_raw 13027 0
joydev 17393 0
parport_pc 32114 0
ppdev 12849 0
bnep 17830 2
rfcomm 38139 16
mac_hid 13077 0
bluetooth 158479 23 btusb,bnep,rfcomm
snd_hda_intel 32719 2
snd_hda_codec 109562 2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 13276 1 snd_hda_codec
cfg80211 178877 1 wl
snd_pcm 80916 2 snd_hda_intel,snd_hda_codec
binfmt_misc 17292 1
lib80211 14040 2 lib80211_crypt_tkip,wl
snd_seq_midi 13132 0
snd_rawmidi 25424 1 snd_seq_midi
i915 423466 3
snd_seq_midi_event 14475 1 snd_seq_midi
snd_seq 51592 3 snd_seq_midi,snd_seq_midi_event
snd_timer 28931 3 snd_hrtimer,snd_pcm,snd_seq
snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq
wmi 18744 1 dell_wmi
snd 62218 14 snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
drm_kms_helper 45466 1 i915
drm 197641 4 i915,drm_kms_helper
soundcore 14635 1 snd
snd_page_alloc 14108 2 snd_hda_intel,snd_pcm
i2c_algo_bit 13199 1 i915
video 19115 1 i915
lp 17455 0
parport 40930 3 parport_pc,ppdev,lp
usbhid 41937 0
hid 77428 1 usbhid
r8169 56368 0
ums_realtek 17920 0
usb_storage 39683 1 ums_realtek
total used free shared buffers cached
Mem: 3062012 1171000 1891012 0 130556 515156
-/+ buffers/cache: 525288 2536724
Swap: 3108540 0 3108540
/usr/lib/pm-utils/sleep.d/00logging suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave suspend suspend:
/usr/lib/pm-utils/sleep.d/00powersave suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01PulseAudio suspend suspend:
Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>>
/usr/lib/pm-utils/sleep.d/01PulseAudio suspend suspend: success.
Running hook /etc/pm/sleep.d/10_grub-common suspend suspend:
/etc/pm/sleep.d/10_grub-common suspend suspend: success.
Running hook /etc/pm/sleep.d/10_unattended-upgrades-hibernate suspend suspend:
/etc/pm/sleep.d/10_unattended-upgrades-hibernate suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend:
Having NetworkManager put all interaces to sleep...Failed.
/usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55wicd suspend suspend:
/usr/lib/pm-utils/sleep.d/55wicd suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend:
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
/usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/75modules suspend suspend:
/usr/lib/pm-utils/sleep.d/75modules suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock suspend suspend:
/usr/lib/pm-utils/sleep.d/90clock suspend suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95anacron suspend suspend:
stop: Unknown instance:
/usr/lib/pm-utils/sleep.d/95anacron suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95hdparm-apm suspend suspend:
/usr/lib/pm-utils/sleep.d/95hdparm-apm suspend suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/95led suspend suspend:
/usr/lib/pm-utils/sleep.d/95led suspend suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend:
Kernel modesetting video driver detected, not using quirks.
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/99video suspend suspend:
kernel.acpi_video_flags = 0
/usr/lib/pm-utils/sleep.d/99video suspend suspend: success.
Running hook /etc/pm/sleep.d/novatel_3g_suspend suspend suspend:
/etc/pm/sleep.d/novatel_3g_suspend suspend suspend: success.
Fri Mar 29 13:17:04 CET 2013: performing suspend
Fri Mar 29 13:17:16 CET 2013: Awake.
Fri Mar 29 13:17:16 CET 2013: Running hooks for resume
Running hook /etc/pm/sleep.d/novatel_3g_suspend resume suspend:
/etc/pm/sleep.d/novatel_3g_suspend resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/99video resume suspend:
/usr/lib/pm-utils/sleep.d/99video resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend:
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95led resume suspend:
/usr/lib/pm-utils/sleep.d/95led resume suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/95hdparm-apm resume suspend:
/dev/sda:
setting Advanced Power Management level to 0xfe (254)
APM_level = 254
/dev/sda:
setting Advanced Power Management level to 0xfe (254)
APM_level = 254
/usr/lib/pm-utils/sleep.d/95hdparm-apm resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95anacron resume suspend:
/usr/lib/pm-utils/sleep.d/95anacron resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock resume suspend:
/usr/lib/pm-utils/sleep.d/90clock resume suspend: not applicable.
Running hook /usr/lib/pm-utils/sleep.d/75modules resume suspend:
Reloaded unloaded modules.
/usr/lib/pm-utils/sleep.d/75modules resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant resume suspend:
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
/usr/lib/pm-utils/sleep.d/60_wpa_supplicant resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55wicd resume suspend:
/usr/lib/pm-utils/sleep.d/55wicd resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend:
Having NetworkManager wake interfaces back up...Failed.
/usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend: success.
Running hook /etc/pm/sleep.d/10_unattended-upgrades-hibernate resume suspend:
/etc/pm/sleep.d/10_unattended-upgrades-hibernate resume suspend: success.
Running hook /etc/pm/sleep.d/10_grub-common resume suspend:
/etc/pm/sleep.d/10_grub-common resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01PulseAudio resume suspend:
Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>> Welcome to PulseAudio! Use "help" for usage information.
>>> >>>
/usr/lib/pm-utils/sleep.d/01PulseAudio resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave resume suspend:
/usr/lib/pm-utils/sleep.d/00powersave resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00logging resume suspend:
/usr/lib/pm-utils/sleep.d/00logging resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/000kernel-change resume suspend:
/usr/lib/pm-utils/sleep.d/000kernel-change resume suspend: success.
Fri Mar 29 13:17:19 CET 2013: Finished.
zkouším vypnout zapnout spojení, nepomáhá, stále odpojeno, pokud chci na internet, musím zapojit kabel.
edit: Teď koukám, že v tom výpisu je to nadvakrát: Poprvé, jak se to po probuzení připojilo a podruhé, jak už se odmítá připojit.
Předpokládám, že problém bude v té druhé části výpisu v tomhle:
/usr/lib/pm-utils/sleep.d/55wicd suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend:
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
-
If the wpa_cli command generates a "Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory" error, make sure you set the ctrl_interface parameter in the /etc/wpa_supplicant.conf as:
ctrl_interface=DIR=/run/wpa_supplicant GROUP=wheel
Toľko k tej hláške, ale neviem či je práve toto problémom :(
edit: ukáž ešte výpis
lshw -C network
lsmod
-
edit: ukáž ešte výpis
lshw -C network
*-network
description: Wireless interface
product: BCM4312 802.11b/g LP-PHY
vendor: Broadcom Corporation
physical id: 1
bus info: pci@0000:0c:00.0
logical name: eth2
version: 01
serial: 70:1a:04:2c:38:3a
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) ip=192.168.2.24 latency=0 multicast=yes wireless=IEEE 802.11abg
resources: irq:17 memory:f69fc000-f69fffff
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:09:00.0
logical name: eth0
version: 03
serial: 00:26:b9:05:ab:8a
size: 10Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s
resources: irq:45 ioport:ce00(size=256) memory:f0204000-f0204fff memory:f0200000-f0203fff memory:f0220000-f023ffff
lsmod:
Module Size Used by
nls_iso8859_1 12617 0
nls_cp437 12751 0
vfat 17308 0
fat 55605 1 vfat
snd_hrtimer 12648 1
ipt_MASQUERADE 12663 1
iptable_nat 13016 1
nf_nat 24959 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 19084 3 iptable_nat,nf_nat
nf_conntrack 73847 4 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 12649 1 nf_conntrack_ipv4
ip_tables 18106 1 iptable_nat
x_tables 22011 3 ipt_MASQUERADE,iptable_nat,ip_tables
bridge 79601 0
stp 12848 1 bridge
snd_hda_codec_conexant 52521 1
snd_hda_intel 32719 2
snd_hda_codec 109562 2 snd_hda_codec_conexant,snd_hda_intel
bnep 17830 2
rfcomm 38139 16
snd_hwdep 13276 1 snd_hda_codec
snd_pcm 80916 2 snd_hda_intel,snd_hda_codec
btusb 17948 2
snd_seq_midi 13132 0
bluetooth 158479 23 bnep,rfcomm,btusb
snd_rawmidi 25424 1 snd_seq_midi
snd_seq_midi_event 14475 1 snd_seq_midi
snd_seq 51592 3 snd_seq_midi,snd_seq_midi_event
snd_timer 28931 3 snd_hrtimer,snd_pcm,snd_seq
snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq
uvcvideo 67203 0
snd 62218 14 snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
lib80211_crypt_tkip 17275 0
soundcore 14635 1 snd
snd_page_alloc 14108 2 snd_hda_intel,snd_pcm
joydev 17393 0
videodev 86588 1 uvcvideo
usbhid 41937 0
hid 77428 1 usbhid
wl 2906597 0
i915 423549 3
parport_pc 32114 0
dell_laptop 17767 0
drm_kms_helper 45466 1 i915
ppdev 12849 0
dcdbas 14098 1 dell_laptop
dell_wmi 12601 0
sparse_keymap 13658 1 dell_wmi
drm 197641 4 i915,drm_kms_helper
cfg80211 178877 1 wl
psmouse 86520 0
serio_raw 13027 0
i2c_algo_bit 13199 1 i915
video 19115 1 i915
lib80211 14040 2 lib80211_crypt_tkip,wl
wmi 18744 1 dell_wmi
mac_hid 13077 0
binfmt_misc 17292 1
lp 17455 0
parport 40930 3 parport_pc,ppdev,lp
r8169 56368 0
ums_realtek 17920 0
usb_storage 39683 1 ums_realtek
-
Je to ten istý ntb? bcm4312 a predtým 4315 Netuším kde je problém, snáď sa pridá niekto skúsený. Skús driver k wifi.
Našiel som len túto užitočnú stránku o BCM
>>>How to Install Broadcom Wireless Drivers (http://askubuntu.com/questions/55868/how-to-install-broadcom-wireless-drivers)<<<
-
Je to ten istý ntb? bcm4312 a predtým 4315 Netuším kde je problém, snáď sa pridá niekto skúsený. Skús driver k wifi.
Našiel som len túto užitočnú stránku o BCM
>>>How to Install Broadcom Wireless Drivers (http://askubuntu.com/questions/55868/how-to-install-broadcom-wireless-drivers)<<<
Je to ten samý ntb. Toho rozdílu jsem si ani nevšiml, a třeba v tom může být potíž.. zkusím se ještě prokousat tím odkazem, mám ten pocit, že po instalaci jsem ovladač jen povoloval z nesvobodných ovladačů...
-
Tak ovladačema to nejspíš nebude, vyzkoušel jsem snad všechny možnosti, ale problém stále přetrvává...
-
Problém (nejspíš) vyřešen!
Tady http://wireless.kernel.org/en/users/Drivers/b43 jsem našel zmínku o alternativě wl
takže jsem v Synapticu zkusil doinstalovat linux-wlan-ng a linux-wlan-ng-source a jemu přiřazené balíky, restaroval, zatím jsem třikrát hibernoval, pokaždé se to připojilo ;)
Ještě to několikrát vyzkouším, abych si to potvrdil a kdyžtak téma označím jako vyřešené :)
-
Takže problém stále přetrvává. Opět nevypočitatelným způsobem. 5x se po probuzení připojil (jednou i při provozu na baterii) dneska ho probudím a zase se snaží marně připojit :(
-
Pravděpodobně vyřešeno, ikdyž sám nevim, jak :)
Rozhodl jsem se vrátit na úplný začátek a v Synapticu tedy odstranil naprosto všechny balíčky a ovladače, které měly něco společného s wi-fi a síťováním. Nechal jsem si pouze základní nm.
Přes instalátor nesvobodných ovladačů nainstaloval ovladač na síťovku a od té doby se normálně připojuje.
Restartoval jsem pouze když aktualizace instalovaly nové kernely (od té doby 2x) jinak se uptime pohyboval kolem 200hodin. 2x denně uspané a probuzené a vždy se připojí ;)
Ale abych si to tím zase nezakřiknul...
-
Otevírám znova toto téma, protože od update kernelu 3.2.0-51 se problém znovu projevuje.
Pokud se chci přes GRUB vrátit k předchozí verzi, tak ta si pro jistotu ani neaktivuje adaptér (kontrolka se nerozsvítí)
Tentokrát se čas od času odmítá připojit i po čistém restartu.
Zjistil jsem, že pokud odeberu nesvobodný ovladač a pomocí připojeného síťového kabelu ho znova stáhnu, tak se na wi-fi znova sám připojí. Měl jsem podezření, že by to byl HW problém s wi-fi modulem (asi po měsíci od zakoupení notebooku mi musel technik vyměnit BT modul, protože odešel), ale to vylučuje výše popsaný postup s opětovnou instalací ovladače. Vypnutí a následné povolení sítě na úrovni nm nebo HW přepínačem nic neřeší.
Může mi někdo potvrdit nebo vyvrátit, že jde o HW problém?
dmesg mi vypíše toto (zvláště ten konec je plný errorů):
mBm)
[33603.832159] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[33603.832162] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832164] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[33603.832167] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832170] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[33603.832172] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832175] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[33603.832178] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832180] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[33603.832183] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[33603.832186] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[33603.832189] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[33603.832192] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[33603.832195] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[33603.832197] cfg80211: Disabling freq 5170 MHz
[33603.832199] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule:
[33603.832202] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832205] cfg80211: Updating information on frequency 5190 MHz for a 20 MHz width channel with regulatory rule:
[33603.832207] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832210] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule:
[33603.832213] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832215] cfg80211: Updating information on frequency 5210 MHz for a 20 MHz width channel with regulatory rule:
[33603.832218] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832221] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule:
[33603.832224] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832226] cfg80211: Updating information on frequency 5230 MHz for a 20 MHz width channel with regulatory rule:
[33603.832229] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832232] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule:
[33603.832235] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832237] cfg80211: Disabling freq 5260 MHz
[33603.832238] cfg80211: Disabling freq 5280 MHz
[33603.832240] cfg80211: Disabling freq 5300 MHz
[33603.832242] cfg80211: Disabling freq 5320 MHz
[33603.832243] cfg80211: Disabling freq 5500 MHz
[33603.832245] cfg80211: Disabling freq 5520 MHz
[33603.832247] cfg80211: Disabling freq 5540 MHz
[33603.832248] cfg80211: Disabling freq 5560 MHz
[33603.832250] cfg80211: Disabling freq 5580 MHz
[33603.832252] cfg80211: Disabling freq 5600 MHz
[33603.832253] cfg80211: Disabling freq 5620 MHz
[33603.832255] cfg80211: Disabling freq 5640 MHz
[33603.832257] cfg80211: Disabling freq 5660 MHz
[33603.832258] cfg80211: Disabling freq 5680 MHz
[33603.832260] cfg80211: Disabling freq 5700 MHz
[33603.832262] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule:
[33603.832265] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832268] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule:
[33603.832271] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832273] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule:
[33603.832276] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832278] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule:
[33603.832281] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832284] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule:
[33603.832287] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832289] cfg80211: Disabling freq 5920 MHz
[33603.832291] cfg80211: Disabling freq 5940 MHz
[33603.832292] cfg80211: Disabling freq 5960 MHz
[33603.832294] cfg80211: Disabling freq 5980 MHz
[33603.832296] cfg80211: Disabling freq 6000 MHz
[33603.832297] cfg80211: Disabling freq 6020 MHz
[33603.832299] cfg80211: Disabling freq 6040 MHz
[33603.832301] cfg80211: Disabling freq 6060 MHz
[33603.832303] cfg80211: Disabling freq 6080 MHz
[33603.832307] cfg80211: World regulatory domain updated:
[33603.832309] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[33603.832312] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832314] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[33603.832317] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[33603.832320] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33603.832322] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[33608.497519] r8169 0000:09:00.0: eth0: link down
[33608.516451] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33608.632521] r8169 0000:09:00.0: eth0: link down
[33608.641082] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33610.508717] r8169 0000:09:00.0: eth0: link down
[33610.516385] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33611.562264] r8169 0000:09:00.0: eth0: link down
[33611.563440] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33612.431421] PM: Syncing filesystems ... done.
[33612.452033] PM: Preparing system for mem sleep
[33612.856618] Freezing user space processes ... (elapsed 0.01 seconds) done.
[33612.872348] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[33612.888349] PM: Entering mem sleep
[33612.888373] Suspending console(s) (use no_console_suspend to debug)
[33612.889645] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[33612.889838] sd 0:0:0:0: [sda] Stopping disk
[33612.907601] wl 0000:0c:00.0: PCI INT A disabled
[33612.912143] uhci_hcd 0000:00:1d.0: PCI INT A disabled
[33612.920434] ehci_hcd 0000:00:1a.7: PCI INT C disabled
[33612.924315] uhci_hcd 0000:00:1a.0: PCI INT A disabled
[33612.944117] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[33612.944141] uhci_hcd 0000:00:1a.1: PCI INT B disabled
[33612.944163] uhci_hcd 0000:00:1a.2: PCI INT C disabled
[33612.944184] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[33612.972063] ehci_hcd 0000:00:1d.7: PCI INT A disabled
[33613.467896] PM: suspend of drv:sd dev:0:0:0:0 complete after 578.284 msecs
[33613.467952] PM: suspend of drv:scsi dev:target0:0:0 complete after 578.334 msecs
[33613.467995] PM: suspend of drv:scsi dev:host0 complete after 562.513 msecs
[33613.484294] PM: suspend of drv:ahci dev:0000:00:1f.2 complete after 577.058 msecs
[33614.012412] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[33614.028251] PM: suspend of drv:snd_hda_intel dev:0000:00:1b.0 complete after 1120.500 msecs
[33614.028303] PM: suspend of drv: dev:pci0000:00 complete after 1120.239 msecs
[33614.028351] PM: suspend of devices complete after 1139.611 msecs
[33614.028356] PM: suspend devices took 1.140 seconds
[33614.029486] r8169 0000:09:00.0: PME# enabled
[33614.029506] pcieport 0000:00:1c.5: wake-up capability enabled by ACPI
[33614.044431] ehci_hcd 0000:00:1d.7: PME# enabled
[33614.056442] ehci_hcd 0000:00:1d.7: wake-up capability enabled by ACPI
[33614.080573] uhci_hcd 0000:00:1d.2: wake-up capability enabled by ACPI
[33614.088888] uhci_hcd 0000:00:1d.1: wake-up capability enabled by ACPI
[33614.096708] uhci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[33614.097003] ehci_hcd 0000:00:1a.7: PME# enabled
[33614.104788] ehci_hcd 0000:00:1a.7: wake-up capability enabled by ACPI
[33614.127966] uhci_hcd 0000:00:1a.2: wake-up capability enabled by ACPI
[33614.136030] uhci_hcd 0000:00:1a.1: wake-up capability enabled by ACPI
[33614.144103] uhci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[33614.144336] PM: late suspend of devices complete after 115.975 msecs
[33614.144794] ACPI: Preparing to enter system sleep state S3
[33614.158336] PM: Saving platform NVS memory
[33614.158380] Disabling non-boot CPUs ...
[33614.160029] CPU 1 is now offline
[33614.160763] Extended CMOS year: 2000
[33614.160763] ACPI: Low-level resume complete
[33614.160763] PM: Restoring platform NVS memory
[33614.160763] Extended CMOS year: 2000
[33614.160763] Enabling non-boot CPUs ...
[33614.160763] Booting Node 0 Processor 1 APIC 0x1
[33614.160763] smpboot cpu 1: start_ip = 9b000
[33614.160017] Initializing CPU#1
[33614.160017] Calibrating delay loop (skipped) already calibrated this CPU
[33614.172630] NMI watchdog enabled, takes one hw-pmu counter.
[33614.176080] CPU1 is up
[33614.177531] ACPI: Waking up from system sleep state S3
[33614.193034] agpgart-intel 0000:00:00.0: restoring config space at offset 0x1 (was 0x20900006, writing 0x30900006)
[33614.193049] i915 0000:00:02.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
[33614.193056] i915 0000:00:02.0: restoring config space at offset 0x8 (was 0x1, writing 0xefe9)
[33614.193060] i915 0000:00:02.0: restoring config space at offset 0x6 (was 0xc, writing 0xe000000c)
[33614.193064] i915 0000:00:02.0: restoring config space at offset 0x4 (was 0x4, writing 0xf6c00004)
[33614.193069] i915 0000:00:02.0: restoring config space at offset 0x1 (was 0x900000, writing 0x900407)
[33614.193095] pci 0000:00:02.1: restoring config space at offset 0x4 (was 0x4, writing 0xf6b00004)
[33614.193100] pci 0000:00:02.1: restoring config space at offset 0x1 (was 0x900000, writing 0x900007)
[33614.193117] uhci_hcd 0000:00:1a.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[33614.193131] uhci_hcd 0000:00:1a.0: restoring config space at offset 0x8 (was 0x1, writing 0x6f61)
[33614.193145] uhci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900001)
[33614.199244] uhci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[33614.199258] uhci_hcd 0000:00:1a.1: restoring config space at offset 0xf (was 0x200, writing 0x207)
[33614.199272] uhci_hcd 0000:00:1a.1: restoring config space at offset 0x8 (was 0x1, writing 0x6f81)
[33614.199286] uhci_hcd 0000:00:1a.1: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900001)
[33614.205293] uhci_hcd 0000:00:1a.1: wake-up capability disabled by ACPI
[33614.205307] uhci_hcd 0000:00:1a.2: restoring config space at offset 0xf (was 0x300, writing 0x304)
[33614.205321] uhci_hcd 0000:00:1a.2: restoring config space at offset 0x8 (was 0x1, writing 0x6fa1)
[33614.205335] uhci_hcd 0000:00:1a.2: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900001)
[33614.211326] uhci_hcd 0000:00:1a.2: wake-up capability disabled by ACPI
[33614.211367] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900106, writing 0x2900102)
[33614.217363] ehci_hcd 0000:00:1a.7: wake-up capability disabled by ACPI
[33614.217370] ehci_hcd 0000:00:1a.7: PME# disabled
[33614.217391] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x107)
[33614.217411] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x4 (was 0xfebfc004, writing 0xf6afc004)
[33614.217417] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[33614.217423] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100102)
[33614.217458] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x20100)
[33614.217470] pcieport 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0xc051c041)
[33614.217476] pcieport 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0xc030c020)
[33614.217481] pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0x0, writing 0x3030)
[33614.217486] pcieport 0000:00:1c.0: restoring config space at offset 0x6 (was 0x0, writing 0xb0b00)
[33614.217495] pcieport 0000:00:1c.0: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
[33614.217502] pcieport 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100507)
[33614.217555] pcieport 0000:00:1c.1: restoring config space at offset 0xf (was 0x200, writing 0x20200)
[33614.217567] pcieport 0000:00:1c.1: restoring config space at offset 0x9 (was 0x10001, writing 0xc011c001)
[33614.217573] pcieport 0000:00:1c.1: restoring config space at offset 0x8 (was 0x0, writing 0xf690f690)
[33614.217578] pcieport 0000:00:1c.1: restoring config space at offset 0x7 (was 0x20000000, writing 0x70002020)
[33614.217584] pcieport 0000:00:1c.1: restoring config space at offset 0x6 (was 0x0, writing 0xc0c00)
[33614.217592] pcieport 0000:00:1c.1: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
[33614.217599] pcieport 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100000, writing 0x48100507)
[33614.217651] pcieport 0000:00:1c.3: restoring config space at offset 0xf (was 0x400, writing 0x20400)
[33614.217663] pcieport 0000:00:1c.3: restoring config space at offset 0x9 (was 0x10001, writing 0xf011f001)
[33614.217669] pcieport 0000:00:1c.3: restoring config space at offset 0x8 (was 0x0, writing 0xf680f660)
[33614.217674] pcieport 0000:00:1c.3: restoring config space at offset 0x7 (was 0x20000000, writing 0xd0d0)
[33614.217679] pcieport 0000:00:1c.3: restoring config space at offset 0x6 (was 0x0, writing 0xe0d00)
[33614.217688] pcieport 0000:00:1c.3: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
[33614.217695] pcieport 0000:00:1c.3: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
[33614.217747] pcieport 0000:00:1c.5: restoring config space at offset 0xf (was 0x200, writing 0x20200)
[33614.217759] pcieport 0000:00:1c.5: restoring config space at offset 0x9 (was 0x10001, writing 0xf021f021)
[33614.217765] pcieport 0000:00:1c.5: restoring config space at offset 0x8 (was 0x0, writing 0xf650f650)
[33614.217770] pcieport 0000:00:1c.5: restoring config space at offset 0x7 (was 0x20000000, writing 0xc0c0)
[33614.217775] pcieport 0000:00:1c.5: restoring config space at offset 0x6 (was 0x0, writing 0x90900)
[33614.217784] pcieport 0000:00:1c.5: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
[33614.217791] pcieport 0000:00:1c.5: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
[33614.217857] uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2900005, writing 0x2900001)
[33614.223449] uhci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[33614.223463] uhci_hcd 0000:00:1d.1: restoring config space at offset 0xf (was 0x200, writing 0x207)
[33614.223478] uhci_hcd 0000:00:1d.1: restoring config space at offset 0x8 (was 0x1, writing 0x6f21)
[33614.223492] uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900001)
[33614.229470] uhci_hcd 0000:00:1d.1: wake-up capability disabled by ACPI
[33614.229483] uhci_hcd 0000:00:1d.2: restoring config space at offset 0xf (was 0x300, writing 0x304)
[33614.229498] uhci_hcd 0000:00:1d.2: restoring config space at offset 0x8 (was 0x1, writing 0x6f41)
[33614.229512] uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900001)
[33614.235524] uhci_hcd 0000:00:1d.2: wake-up capability disabled by ACPI
[33614.235565] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900106, writing 0x2900102)
[33614.241540] ehci_hcd 0000:00:1d.7: wake-up capability disabled by ACPI
[33614.241547] ehci_hcd 0000:00:1d.7: PME# disabled
[33614.241571] pci 0000:00:1e.0: restoring config space at offset 0x7 (was 0x2280e0f0, writing 0x228000f0)
[33614.241631] pci 0000:00:1f.0: restoring config space at offset 0x1 (was 0x2100007, writing 0x2100107)
[33614.241664] ahci 0000:00:1f.2: restoring config space at offset 0xf (was 0x200, writing 0x20a)
[33614.241689] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
[33614.241728] pci 0000:00:1f.3: restoring config space at offset 0xf (was 0x200, writing 0x20a)
[33614.241748] pci 0000:00:1f.3: restoring config space at offset 0x4 (was 0x4, writing 0xf6afbf04)
[33614.241756] pci 0000:00:1f.3: restoring config space at offset 0x1 (was 0x2800001, writing 0x2800103)
[33614.242023] wl 0000:0c:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[33614.242084] wl 0000:0c:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf69fc004)
[33614.242096] wl 0000:0c:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[33614.242113] wl 0000:0c:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x8100106)
[33614.242282] r8169 0000:09:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
[33614.242334] r8169 0000:09:00.0: restoring config space at offset 0x8 (was 0xc, writing 0xf020000c)
[33614.242356] r8169 0000:09:00.0: restoring config space at offset 0x6 (was 0xc, writing 0xf020400c)
[33614.242377] r8169 0000:09:00.0: restoring config space at offset 0x4 (was 0x1, writing 0xce01)
[33614.242392] r8169 0000:09:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[33614.242413] r8169 0000:09:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100507)
[33614.243223] PM: early resume of devices complete after 50.386 msecs
[33614.243784] i915 0000:00:02.0: setting latency timer to 64
[33614.249224] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[33614.249231] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[33614.249260] usb usb3: root hub lost power or was reset
[33614.249276] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[33614.249283] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[33614.249310] usb usb4: root hub lost power or was reset
[33614.249324] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[33614.249330] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[33614.249357] usb usb5: root hub lost power or was reset
[33614.249373] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[33614.249380] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[33614.249411] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[33614.249418] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[33614.249467] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[33614.249523] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[33614.249530] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[33614.249558] usb usb6: root hub lost power or was reset
[33614.249573] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[33614.249579] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[33614.249606] usb usb7: root hub lost power or was reset
[33614.249619] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[33614.249626] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[33614.249652] usb usb8: root hub lost power or was reset
[33614.249669] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[33614.249675] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[33614.249703] pci 0000:00:1e.0: setting latency timer to 64
[33614.249722] ahci 0000:00:1f.2: setting latency timer to 64
[33614.249976] wl 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[33614.249987] wl 0000:0c:00.0: setting latency timer to 64
[33614.250094] pcieport 0000:00:1c.5: wake-up capability disabled by ACPI
[33614.250110] r8169 0000:09:00.0: PME# disabled
[33614.328486] r8169 0000:09:00.0: eth0: link down
[33614.373605] sd 0:0:0:0: [sda] Starting disk
[33614.460302] PM: resume of drv:i915 dev:0000:00:02.0 complete after 216.517 msecs
[33614.492250] PM: resume of drv:hub dev:8-0:1.0 complete after 118.712 msecs
[33614.492263] PM: resume of drv: dev:ep_00 complete after 118.685 msecs
[33614.492272] PM: resume of drv: dev:ep_81 complete after 118.715 msecs
[33614.492285] PM: resume of drv:hub dev:4-0:1.0 complete after 118.959 msecs
[33614.492297] PM: resume of drv: dev:ep_00 complete after 118.959 msecs
[33614.492307] PM: resume of drv: dev:ep_81 complete after 118.974 msecs
[33614.492342] PM: resume of drv:hub dev:7-0:1.0 complete after 118.897 msecs
[33614.492354] PM: resume of drv: dev:ep_00 complete after 118.865 msecs
[33614.492361] PM: resume of drv:hub dev:5-0:1.0 complete after 119.012 msecs
[33614.492366] PM: resume of drv: dev:ep_81 complete after 118.898 msecs
[33614.492374] PM: resume of drv: dev:ep_81 complete after 119.017 msecs
[33614.492379] PM: resume of drv: dev:ep_00 complete after 119.011 msecs
[33614.520243] PM: resume of drv: dev:ep_00 complete after 146.955 msecs
[33614.520263] PM: resume of drv:hub dev:2-0:1.0 complete after 146.987 msecs
[33614.520323] PM: resume of drv: dev:ep_81 complete after 147.039 msecs
[33614.572239] PM: resume of drv:hub dev:1-0:1.0 complete after 198.988 msecs
[33614.572251] PM: resume of drv: dev:ep_00 complete after 198.987 msecs
[33614.572280] PM: resume of drv: dev:ep_81 complete after 199.024 msecs
[33614.596226] PM: resume of drv:hub dev:6-0:1.0 complete after 222.846 msecs
[33614.596242] PM: resume of drv: dev:ep_00 complete after 222.851 msecs
[33614.596265] PM: resume of drv: dev:ep_81 complete after 222.877 msecs
[33614.596279] PM: resume of drv: dev:ep_00 complete after 222.965 msecs
[33614.596308] PM: resume of drv:hub dev:3-0:1.0 complete after 223.004 msecs
[33614.596327] PM: resume of drv: dev:ep_81 complete after 223.019 msecs
[33614.640295] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[33614.648057] ata5: SATA link down (SStatus 4 SControl 300)
[33614.656129] ata6: SATA link down (SStatus 4 SControl 300)
[33614.684064] usb 1-4: reset high-speed USB device number 3 using ehci_hcd
[33614.743200] ata2.00: configured for UDMA/100
[33614.823924] PM: resume of drv: dev:ep_00 complete after 450.155 msecs
[33614.823932] PM: resume of drv:ums-realtek dev:1-4:1.0 complete after 450.229 msecs
[33614.823958] PM: resume of drv: dev:ep_01 complete after 450.235 msecs
[33614.823966] PM: resume of drv:scsi dev:host7 complete after 450.049 msecs
[33614.823978] PM: resume of drv: dev:ep_82 complete after 450.234 msecs
[33614.823985] PM: resume of drv:scsi_host dev:host7 complete after 450.053 msecs
[33614.823997] PM: resume of drv:scsi dev:target7:0:0 complete after 449.861 msecs
[33614.824040] PM: resume of drv:sd dev:7:0:0:0 complete after 449.883 msecs
[33614.824074] PM: resume of drv:scsi_device dev:7:0:0:0 complete after 449.896 msecs
[33614.928063] usb 1-6: reset high-speed USB device number 4 using ehci_hcd
[33615.133559] PM: resume of drv:uvcvideo dev:1-6:1.1 complete after 759.691 msecs
[33615.133570] PM: resume of drv: dev:ep_00 complete after 759.682 msecs
[33615.133576] PM: resume of drv:uvcvideo dev:1-6:1.0 complete after 759.748 msecs
[33615.133610] PM: resume of drv: dev:ep_83 complete after 759.764 msecs
[33615.320293] usb 6-1: reset low-speed USB device number 4 using uhci_hcd
[33615.633426] PM: resume of drv:usbhid dev:6-1:1.1 complete after 1259.078 msecs
[33615.633440] PM: resume of drv: dev:ep_00 complete after 1259.049 msecs
[33615.633449] PM: resume of drv:usbhid dev:6-1:1.0 complete after 1259.144 msecs
[33615.633455] PM: resume of drv: dev:ep_82 complete after 1259.081 msecs
[33615.633475] PM: resume of drv: dev:ep_81 complete after 1259.148 msecs
[33615.776293] usb 3-1: reset full-speed USB device number 2 using uhci_hcd
[33616.140231] PM: resume of drv: dev:ep_00 complete after 1766.203 msecs
[33616.140252] PM: resume of drv:hub dev:3-1:1.0 complete after 1766.277 msecs
[33616.140324] PM: resume of drv: dev:ep_81 complete after 1766.327 msecs
[33616.144351] PM: resume of drv:btusb dev:3-1.3:1.1 complete after 1769.831 msecs
[33616.144365] PM: resume of drv:btusb dev:3-1.3:1.0 complete after 1769.933 msecs
[33616.144372] PM: resume of drv:usb dev:3-1.3:1.2 complete after 1769.781 msecs
[33616.144384] PM: resume of drv: dev:ep_81 complete after 1769.930 msecs
[33616.144390] PM: resume of drv:usb dev:3-1.3:1.3 complete after 1769.737 msecs
[33616.144395] PM: resume of drv: dev:ep_82 complete after 1769.920 msecs
[33616.144400] PM: resume of drv: dev:ep_00 complete after 1769.729 msecs
[33616.144405] PM: resume of drv: dev:ep_02 complete after 1769.909 msecs
[33616.144409] PM: resume of drv: dev:ep_83 complete after 1769.869 msecs
[33616.144428] PM: resume of drv: dev:ep_03 complete after 1769.866 msecs
[33616.144434] PM: resume of drv: dev:ep_04 complete after 1769.802 msecs
[33616.144449] PM: resume of drv: dev:ep_84 complete after 1769.844 msecs
[33616.213348] usb 3-1.1: reset full-speed USB device number 3 using uhci_hcd
[33616.325350] PM: resume of drv: dev:ep_00 complete after 1951.236 msecs
[33616.325365] PM: resume of drv:usbhid dev:3-1.1:1.0 complete after 1951.295 msecs
[33616.325423] PM: resume of drv: dev:ep_81 complete after 1951.331 msecs
[33616.385348] usb 3-1.2: reset full-speed USB device number 4 using uhci_hcd
[33616.500346] PM: resume of drv: dev:ep_00 complete after 2126.084 msecs
[33616.500366] PM: resume of drv:usb dev:3-1.2:1.0 complete after 2126.146 msecs
[33616.500445] PM: resume of drv: dev:ep_81 complete after 2126.204 msecs
[33617.824227] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[33617.834038] ata1.00: configured for UDMA/133
[33617.858731] PM: resume of drv:sd dev:0:0:0:0 complete after 3485.126 msecs
[33617.858746] PM: resume of drv:scsi_device dev:0:0:0:0 complete after 3485.097 msecs
[33617.858769] PM: resume of drv:scsi_disk dev:0:0:0:0 complete after 3485.533 msecs
[33617.863423] input input15: event field not found
[33617.863491] PM: resume of devices complete after 3620.228 msecs
[33617.863683] PM: resume devices took 3.620 seconds
[33617.863731] PM: Finishing wakeup.
[33617.863732] Restarting tasks ...
[33617.874298] usb 3-1.3: USB disconnect, device number 7
[33617.889751] done.
[33617.931016] video LNXVIDEO:00: Restoring backlight state
[33617.970295] sd 7:0:0:0: [sdd] Test WP failed, assume Write Enabled
[33617.972668] sd 7:0:0:0: [sdd] Asking for cache data failed
[33617.972672] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[33619.097343] usb 3-1.3: new full-speed USB device number 8 using uhci_hcd
[33623.426309] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[33623.967531] r8169 0000:09:00.0: eth0: link down
[33623.967979] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33624.162015] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[33624.371515] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[33626.676505] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[33651.925641] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[33655.235225] INFO @wl_cfg80211_scan : system busy : scan for "" canceled
[33655.235537] INFO @wl_cfg80211_scan : system busy : scan for "" canceled
[33655.451041] INFO @wl_cfg80211_scan : system busy : scan for "" canceled
[33655.681915] r8169 0000:09:00.0: eth0: link down
[33655.682247] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33662.514676] INFO @wl_cfg80211_scan : system busy : scan for "" canceled
[33662.681597] r8169 0000:09:00.0: eth0: link down
[33662.682217] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33669.656759] sd 7:0:0:0: [sdd] Test WP failed, assume Write Enabled
[33669.658804] sd 7:0:0:0: [sdd] Asking for cache data failed
[33669.658809] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[33671.435472] r8169 0000:09:00.0: eth0: link down
[33671.435704] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33672.948928] r8169 0000:09:00.0: eth0: link down
[33672.949340] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33715.439878] INFO @wl_cfg80211_scan : system busy : scan for "" canceled
[33715.634978] r8169 0000:09:00.0: eth0: link down
[33715.635411] ADDRCONF(NETDEV_UP): eth0: link is not ready
[33715.979291] INFO @wl_cfg80211_scan : system busy : scan for "" canceled
[33716.899184] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
[33717.051837] ERROR @wl_notify_scan_status : eth2 Scan_results error (-22)
-
Tak problém je opět vyřešen a teď už snad natrvalo.
Pátráním na internetu jsem zjistil, že tento bug trápí více uživatelů. Vyzkoušel jsem několik návodů, ale jako jedinný účinný se osvědčil tento:
http://askubuntu.com/questions/67280/wireless-doesnt-connect-after-suspend-on-an-asus-k52f