Jsem z Prahy, bydlím kousek od té Libuše. Akorát ten notebook potřebuji denně, takže ho nemůžu někde nechat. :-/
Už si připadám jak naprostej trotl. Vše dělám tak, jak se píše ve všech návodech. Na 12.04.2 se mi po instalaci bumblebee nespustil ani systém. Zkoušel jsem i nahrát novější kernel, taky nic. Dal jsem zpět 12.10 a po instalaci se systém spustil, ale stále to žere jak kráva a když zkusím, jestli ta nvidia funguje, tak mi to vypíše tohle:
-UX32VD:~$ optirun glxspheres
[ 410.903068] [ERROR]The Bumblebee daemon has not been started yet or the socket path /var/run/bumblebee.socket was incorrect.
[ 410.903228] [ERROR]Could not connect to bumblebee daemon - is it running?
Takže jako by to bumblebee nefungovalo. Furt jede větrák, což předtím taky nebylo.
Podle mě, to musí být problém v tom bumblebee 3.1, které vyšlo teď před pár dny, protože mi to dva měsíce běželo krásně bez problémů a to jsem pak nemusel ani upravovat žádné bumblebee.conf.
V jednom návodu se píše, že tam počítaj s verzí biosu 211, já mám 206. Ale i na té 206 to bez problémů běželo. Bios se mi moc flashovat nechce, protože všude píšou, že pouze ve výjimečných případech. Mé vlastní zkušenosti jsou taky proti tomu, protože jsem takto už jednu základovku odrovnal.
Tady ještě dodám tu kopii bumblebee.conf, kterou jsem už poupravil dle jednoho z těch návodů.
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=nvidia
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia-current:/usr/lib32/nvidia-current
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia-current/xorg,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau