Dávám výpis:
[sup][ 0.224780] Scanning for low memory corruption every 60 seconds
[ 0.225023] audit: initializing netlink socket (disabled)
[ 0.225105] type=2000 audit(1350569468.222:1): initialized
[ 0.240076] Trying to unpack rootfs image as initramfs...
[ 0.259146] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.261538] VFS: Disk quotas dquot_6.5.2
[ 0.261697] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.262660] fuse init (API version 7.13)
[ 0.262867] msgmni has been set to 946
[ 0.267105] alg: No test for stdrng (krng)
[ 0.267280] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.267367] io scheduler noop registered
[ 0.267425] io scheduler anticipatory registered
[ 0.267486] io scheduler deadline registered
[ 0.267609] io scheduler cfq registered (default)
[ 0.267835] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.267930] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.268215] ACPI: AC Adapter [ACAD] (off-line)
[ 0.268392] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 0.268535] ACPI: Lid Switch [LID]
[ 0.268652] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 0.268742] ACPI: Power Button [PWRB]
[ 0.268859] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 0.268948] ACPI: Sleep Button [SLPB]
[ 0.269076] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.269164] ACPI: Power Button [PWRF]
[ 0.269549] Marking TSC unstable due to TSC halts in idle
[ 0.269710] processor LNXCPU:00: registered as cooling_device0
[ 0.270759] Switching to clocksource acpi_pm
[ 0.290943] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.291474] alloc irq_desc for 17 on node -1
[ 0.291478] alloc kstat_irqs on node -1
[ 0.291491] serial 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.291563] serial 0000:00:1f.6: PCI INT B disabled
[ 0.293060] brd: module loaded
[ 0.293804] loop: module loaded
[ 0.293989] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.294234] ata_piix 0000:00:1f.1: version 2.13
[ 0.294247] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[ 0.294317] alloc irq_desc for 18 on node -1
[ 0.294320] alloc kstat_irqs on node -1
[ 0.294329] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.294446] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.300425] isapnp: Scanning for PnP cards...
[ 0.306004] scsi0 : ata_piix
[ 0.306240] scsi1 : ata_piix
[ 0.307589] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1100 irq 14
[ 0.307658] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
[ 0.308074] ACPI: Battery Slot [BAT1] (battery present)
[ 0.308916] Fixed MDIO Bus: probed
[ 0.309030] PPP generic driver version 2.4.2
[ 0.309200] tun: Universal TUN/TAP device driver, 1.6
[ 0.309263] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.309457] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.309555] alloc irq_desc for 23 on node -1
[ 0.309559] alloc kstat_irqs on node -1
[ 0.309569] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.309654] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.309659] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.309774] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.309906] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.313835] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.364441] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf0080000
[ 0.384216] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.384494] usb usb1: configuration #1 chosen from 1 choice
[ 0.384608] hub 1-0:1.0: USB hub found
[ 0.384678] hub 1-0:1.0: 6 ports detected
[ 0.384833] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.384924] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.385077] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.385152] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.385157] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.385283] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.385412] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001200
[ 0.385612] usb usb2: configuration #1 chosen from 1 choice
[ 0.385709] hub 2-0:1.0: USB hub found
[ 0.385775] hub 2-0:1.0: 2 ports detected
[ 0.385888] alloc irq_desc for 19 on node -1
[ 0.385891] alloc kstat_irqs on node -1
[ 0.385901] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.385973] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.385978] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.386087] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.386200] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001600
[ 0.386380] usb usb3: configuration #1 chosen from 1 choice
[ 0.386479] hub 3-0:1.0: USB hub found
[ 0.386545] hub 3-0:1.0: 2 ports detected
[ 0.386653] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.386724] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.386729] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.386831] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.386943] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001700
[ 0.387134] usb usb4: configuration #1 chosen from 1 choice
[ 0.387230] hub 4-0:1.0: USB hub found
[ 0.387295] hub 4-0:1.0: 2 ports detected
[ 0.387480] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 0.387858] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.387976] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.392173] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.392300] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.392392] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.392482] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.392751] mice: PS/2 mouse device common for all mice
[ 0.393050] rtc_cmos 00:04: RTC can wake from S4
[ 0.393177] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.393269] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 0.393546] device-mapper: uevent: version 1.0.3
[ 0.393787] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.395997] device-mapper: multipath: version 1.1.0 loaded
[ 0.396088] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.396466] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 0.399479] EISA: Probing bus 0 at eisa.0
[ 0.399551] Cannot allocate resource for EISA slot 1
[ 0.399640] EISA: Detected 0 cards.
[ 0.399842] cpuidle: using governor ladder
[ 0.399984] cpuidle: using governor menu
[ 0.400664] TCP cubic registered
[ 0.400959] NET: Registered protocol family 10
[ 0.402048] NET: Registered protocol family 17
[ 0.402189] Using IPI No-Shortcut mode
[ 0.402369] PM: Resume from disk failed.
[ 0.402400] registered taskstats version 1
[ 0.402713] Magic number: 0:478:182
[ 0.402891] rtc_cmos 00:04: setting system clock to 2012-10-18 14:11:09 UTC (1350569469)
[ 0.404122] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.404186] EDD information not available.
[ 0.472887] ata2.01: NODEV after polling detection
[ 0.473002] ata1.00: ATA-6: ST94019A, 3.05, max UDMA/100
[ 0.473074] ata1.00: 78140160 sectors, multi 16: LBA48
[ 0.473168] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 0.480550] ata2.00: ATAPI: QSI DVD+/-RW SDW-082, LX34, max UDMA/33
[ 0.488854] ata1.00: configured for UDMA/33
[ 0.496554] ata2.00: configured for UDMA/33
[ 0.907549] Freeing initrd memory: 7815k freed
[ 0.959034] isapnp: No Plug & Play device found
[ 0.959379] scsi 0:0:0:0: Direct-Access ATA ST94019A 3.05 PQ: 0 ANSI: 5
[ 0.959773] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.960137] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 0.960292] sd 0:0:0:0: [sda] Write Protect is off
[ 0.960355] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.960392] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.960720] sda:
[ 0.961801] scsi 1:0:0:0: CD-ROM QSI DVD+-RW SDW-082 LX34 PQ: 0 ANSI: 5
[ 0.963904] sr0: scsi3-mmc drive: 62x/62x writer cd/rw xa/form2 cdda tray
[ 0.963973] Uniform CD-ROM driver Revision: 3.20
[ 0.964190] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 0.964265] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 0.979275] sda1 sda2 < sda5 sda6 sda7 >
[ 1.013159] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.013240] Freeing unused kernel memory: 664k freed
[ 1.013874] Write protecting the kernel text: 4700k
[ 1.013988] Write protecting the kernel read-only data: 1844k
[ 1.037084] udev: starting version 151
[ 1.304344] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.304450] 8139cp 0000:01:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.309742] 8139too Fast Ethernet driver 0.9.28
[ 1.309856] alloc irq_desc for 21 on node -1
[ 1.309859] alloc kstat_irqs on node -1
[ 1.309870] 8139too 0000:01:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 1.311130] eth0: RealTek RTL8139 at 0xc000, 00:0f:b0:7f:7c:5f, IRQ 21
[ 1.845185] EXT4-fs (sda6): mounted filesystem with ordered data mode
[ 11.996365] Adding 710648k swap on /dev/sda7. Priority:-1 extents:1 across:710648k
[ 12.047743] udev: starting version 151
[ 12.633289] acer-wmi: Acer Laptop ACPI-WMI Extras
[ 12.633316] acer-wmi: No or unsupported WMI interface, unable to load
[ 12.684956] type=1505 audit(1350562281.781:2): operation="profile_load" pid=504 name="/sbin/dhclient3"
[ 12.685864] type=1505 audit(1350562281.781:3): operation="profile_load" pid=504 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.686373] type=1505 audit(1350562281.781:4): operation="profile_load" pid=504 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.905661] Linux agpgart interface v0.103
[ 12.915392] [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
[ 12.917267] acpi device:03: registered as cooling_device1
[ 12.918279] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input6
[ 12.918464] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 13.057514] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[ 13.057803] agpgart-intel 0000:00:00.0: detected 16252K stolen memory
[ 13.065272] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xb0000000
[ 13.066129] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.126942] intel_rng: Firmware space is locked read-only. If you can't or
[ 13.126946] intel_rng: don't want to disable this in firmware setup, and if
[ 13.126948] intel_rng: you are certain that your system has a functional
[ 13.126950] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 13.173272] lp: driver loaded but no devices found
[ 13.306013] [drm] Initialized drm 1.1.0 20060810
[ 13.494906] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x256eb1, caps: 0x804713/0x0/0x0
[ 13.525846] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[ 14.059707] eth0: link down
[ 14.059811] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.207007] yenta_cardbus 0000:01:04.0: CardBus bridge found [1025:0071]
[ 14.207029] yenta_cardbus 0000:01:04.0: Using CSCINT to route CSC interrupts to PCI
[ 14.207033] yenta_cardbus 0000:01:04.0: Routing CardBus interrupts to PCI
[ 14.207039] yenta_cardbus 0000:01:04.0: TI: mfunc 0x00111c12, devctl 0x46
[ 14.207635] [drm] i915 disabling kernel modesetting for known bad device.
[ 14.207664] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 14.207671] pci 0000:00:02.0: setting latency timer to 64
[ 14.213538] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 14.293193] vga16fb: initializing
[ 14.293199] vga16fb: mapped to 0xc00a0000
[ 14.293407] fb0: VGA16 VGA frame buffer device
[ 14.408266] type=1505 audit(1350562283.505:5): operation="profile_load" pid=655 name="/usr/share/gdm/guest-session/Xsession"
[ 14.412059] type=1505 audit(1350562283.505:6): operation="profile_replace" pid=667 name="/sbin/dhclient3"
[ 14.413399] type=1505 audit(1350562283.509:7): operation="profile_replace" pid=667 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.413909] type=1505 audit(1350562283.509:8): operation="profile_replace" pid=667 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.436781] yenta_cardbus 0000:01:04.0: ISA IRQ mask 0x0c98, PCI irq 16
[ 14.436788] yenta_cardbus 0000:01:04.0: Socket status: 30000020
[ 14.436794] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05
[ 14.436809] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xdfff
[ 14.436815] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xdfff: clean.
[ 14.437405] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xefffffff
[ 14.437410] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge Memory window: 0xa0000000 - 0xafffffff
[ 14.600945] Console: switching to colour frame buffer device 80x30
[ 14.629129] type=1505 audit(1350562283.725:9): operation="profile_load" pid=668 name="/usr/bin/evince"
[ 14.656365] type=1505 audit(1350562283.753:10): operation="profile_load" pid=668 name="/usr/bin/evince-previewer"
[ 14.663727] type=1505 audit(1350562283.757:11): operation="profile_load" pid=668 name="/usr/bin/evince-thumbnailer"
[ 15.061181] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 15.061226] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 15.096095] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 15.096140] pci 0000:02:00.0: reg 10 32bit mmio: [0xffffe000-0xffffffff]
[ 15.096214] yenta_cardbus 0000:01:04.0: EnE: chaning testregister 0xC9, 04 -> 04
[ 15.209073] cfg80211: Calling CRDA to update world regulatory domain
[ 15.235141] cfg80211: World regulatory domain updated:
[ 15.235147] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.235152] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.235156] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.235160] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.235164] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.235168] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.248985] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 15.250607] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 15.251317] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 15.251910] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 15.253211] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 15.400935] rt2500pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 15.400949] rt2500pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.400959] rt2500pci 0000:02:00.0: setting latency timer to 64
[ 15.454362] phy0: Selected rate control algorithm 'minstrel'
[ 15.455338] Registered led device: rt2500pci-phy0::radio
[ 15.455364] Registered led device: rt2500pci-phy0::quality
[ 15.492672] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 15.896030] intel8x0_measure_ac97_clock: measured 55277 usecs (2663 samples)
[ 15.896035] intel8x0: clocking to 48000
[ 73.983413] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 124.752828] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 124.994998] ISO 9660 Extensions: RRIP_1991A
[ 398.314206] pcmcia_socket pcmcia_socket0: pccard: card ejected from slot 0
[ 398.604396] rt2500pci 0000:02:00.0: PCI INT A disabled
[ 400.480144] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 400.480190] pci 0000:02:00.0: reg 10 32bit mmio: [0xffffe000-0xffffffff]
[ 400.480264] yenta_cardbus 0000:01:04.0: EnE: chaning testregister 0xC9, 04 -> 04
[ 400.480924] rt2500pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 400.480937] rt2500pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 400.480946] rt2500pci 0000:02:00.0: setting latency timer to 64
[ 400.510733] phy1: Selected rate control algorithm 'minstrel'
[ 400.515506] Registered led device: rt2500pci-phy1::radio
[ 400.517865] Registered led device: rt2500pci-phy1::quality
[ 400.556742] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 548.372292] wlan0: deauthenticating from c8:60:00:90:20:ec by local choice (reason=3)
[ 548.377682] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 548.381032] wlan0: direct probe responded
[ 548.381036] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 548.382684] wlan0: authenticated
[ 548.382706] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 548.384939] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 548.384943] wlan0: associated
[ 548.385538] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 552.516035] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 558.864125] wlan0: no IPv6 routers present
[ 606.452128] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 608.952139] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 610.291359] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 610.488153] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 610.688126] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 610.888123] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 720.473589] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 720.476902] wlan0: direct probe responded
[ 720.476907] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 720.478669] wlan0: authenticated
[ 720.478693] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 720.480934] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 720.480938] wlan0: associated
[ 722.688137] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 726.500027] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 727.840480] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 728.040135] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 728.240133] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 728.440055] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 757.774192] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 757.777601] wlan0: direct probe responded
[ 757.777606] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 757.779297] wlan0: authenticated
[ 757.779320] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 757.781891] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 757.781895] wlan0: associated
[ 766.500136] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 767.840916] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 768.040034] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 768.240137] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 768.440136] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 779.083821] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 779.280142] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 779.480140] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 779.680131] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 783.396371] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 783.399697] wlan0: direct probe responded
[ 783.399702] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 783.401434] wlan0: authenticated
[ 783.401459] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 783.407460] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 783.407464] wlan0: associated
[ 789.288135] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 790.152030] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 799.500138] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 813.299266] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 813.496036] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 813.696128] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 813.896128] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 816.380269] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 816.580138] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 816.780143] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 816.980090] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 833.857610] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 833.860954] wlan0: direct probe responded
[ 833.860958] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 833.863786] wlan0: authenticated
[ 833.863810] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 833.866048] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 833.866052] wlan0: associated
[ 839.340134] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 848.648133] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 906.069615] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 906.072945] wlan0: direct probe responded
[ 906.072950] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 906.074627] wlan0: authenticated
[ 906.074651] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 906.076897] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 906.076902] wlan0: associated
[ 911.500150] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 912.842772] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 913.040045] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 913.043384] wlan0: direct probe responded
[ 913.043391] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 913.045054] wlan0: authenticated
[ 913.045079] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 913.047476] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 913.047480] wlan0: associated
[ 921.500147] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 922.841630] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 923.040143] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 923.240147] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 923.440149] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 940.318585] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 940.321892] wlan0: direct probe responded
[ 940.321899] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 940.324401] wlan0: authenticated
[ 940.324438] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 940.326393] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 940.326398] wlan0: associated
[ 955.684028] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1006.452126] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1008.952141] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 1010.291420] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 1010.488130] wlan0: direct probe to AP c8:60:00:90:20:ec (try 2)
[ 1010.688128] wlan0: direct probe to AP c8:60:00:90:20:ec (try 3)
[ 1010.888130] wlan0: direct probe to AP c8:60:00:90:20:ec timed out
[ 1255.548164] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 1255.552545] wlan0: direct probe responded
[ 1255.552553] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 1255.554863] wlan0: authenticated
[ 1255.554891] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 1255.558671] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=2)
[ 1255.558675] wlan0: associated
[ 1259.008047] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1264.652138] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1264.736030] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1283.900144] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1286.516146] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1326.448040] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1352.872144] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1378.500141] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 1410.998930] wlan0: direct probe to AP c8:60:00:90:20:ec (try 1)
[ 1411.000864] wlan0: direct probe responded
[ 1411.000869] wlan0: authenticate with AP c8:60:00:90:20:ec (try 1)
[ 1411.003107] wlan0: authenticated
[ 1411.003128] wlan0: associate with AP c8:60:00:90:20:ec (try 1)
[ 1411.005341] wlan0: RX AssocResp from c8:60:00:90:20:ec (capab=0x411 status=0 aid=1)
[ 1411.005345] wlan0: associated
[ 1415.392031] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1421.080032] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1446.996127] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1450.372127] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1466.452133] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1506.452135] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1549.480138] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1566.452137] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1646.452139] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1746.452137] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1826.376138] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1866.452139] phy1 -> rt2500pci_set_device_state: Error - Device failed to enter state 3 (-16).
[ 1916.500138] No probe response from AP c8:60:00:90:20:ec after 500ms, disconnecting.
[ 2940.911621] ata2: drained 32768 bytes to clear DRQ.
[ 2940.966951] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2940.966957] ata2.00: ST_FIRST: !(DRQ|ERR|DF)
[ 2940.966962] sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[ 2940.966979] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 2940.966981] res 58/00:01:00:00:00/00:00:00:00:00/a0 Emask 0x2 (HSM violation)
[ 2940.966985] ata2.00: status: { DRDY DRQ }
[ 2940.967016] ata2: soft resetting link
[ 2941.120319] ata2.01: NODEV after polling detection
[ 2941.145368] ata2.00: configured for UDMA/33
[ 2941.151288] ata2: EH complete[/sup] Systém je nainstalovaný z dvd.Spustit jde jen z nabídky Run in fail safe graphic mode.
Téma: Zasekávání systému u ACER 2355 (Přečteno 1586 krát)
