... zkusil jsem ty příkazy:
sudo rmmod coretemp
sudo modprobe coretemp
ale nepomohlo to. Větrák se nezklidnil, takže jsem ten script zatám ani nevytvářel.
lsmod | grep coretemp hlásí:
coretemp 13283 0
Tady je celý výpis z "sensors-detect", mohl bys na to, prosím" mrknout? Třeba tam najdeš nějakej problém.
Díky:)
# sensors-detect revision 5861 (2010-09-21 17:21:05 +0200)
# System: Hewlett-Packard HP ProBook 4510s (laptop)
# Board: Hewlett-Packard 3072
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): yes
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel digital thermal sensor... Success!
(driver `coretemp')
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): yes
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown chip with ID 0x4501
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): yes
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): yes
Sorry, no supported PCI bus adapters found.
Module i2c-dev loaded successfully.
Next adapter: i915 gmbus disabled (i2c-0)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 gmbus ssc (i2c-1)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 GPIOB (i2c-2)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 gmbus vga (i2c-3)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 GPIOA (i2c-4)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 gmbus panel (i2c-5)
Do you want to scan it? (YES/no/selectively): yes
Client found at address 0x28
Probing for `National Semiconductor LM78'... No
Probing for `National Semiconductor LM79'... No
Probing for `National Semiconductor LM80'... No
Probing for `Winbond W83781D'... No
Probing for `Winbond W83782D'... No
Probing for `Winbond W83627HF'... No
Probing for `Winbond W83627EHF'... No
Probing for `Winbond W83627DHG/W83667HG/W83677HG'... No
Probing for `Asus AS99127F (rev.1)'... No
Probing for `Asus AS99127F (rev.2)'... No
Probing for `Asus ASB100 Bach'... No
Probing for `Analog Devices ADM1029'... No
Probing for `ITE IT8712F'... No
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Next adapter: i915 GPIOC (i2c-6)
Do you want to scan it? (YES/no/selectively): yes
Client found at address 0x28
Probing for `National Semiconductor LM78'... No
Probing for `National Semiconductor LM79'... No
Probing for `National Semiconductor LM80'... No
Probing for `Winbond W83781D'... No
Probing for `Winbond W83782D'... No
Probing for `Winbond W83627HF'... No
Probing for `Winbond W83627EHF'... No
Probing for `Winbond W83627DHG/W83667HG/W83677HG'... No
Probing for `Asus AS99127F (rev.1)'... No
Probing for `Asus AS99127F (rev.2)'... No
Probing for `Asus ASB100 Bach'... No
Probing for `Analog Devices ADM1029'... No
Probing for `ITE IT8712F'... No
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Next adapter: i915 gmbus dpc (i2c-7)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 GPIOD (i2c-8)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 gmbus dpb (i2c-9)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 GPIOE (i2c-10)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 gmbus reserved (i2c-11)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 gmbus dpd (i2c-12)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: i915 GPIOF (i2c-13)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: DPDDC-B (i2c-14)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: DPDDC-D (i2c-15)
Do you want to scan it? (YES/no/selectively): yes
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `coretemp':
* Chip `Intel digital thermal sensor' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run 'service module-init-tools start'
to load them.
Unloading i2c-dev... OK
Unloading cpuid... OK