Fórum Ubuntu CZ/SK

Ostatní => Archiv => Téma založeno: ScH0ll_kIll3r 16 Listopadu 2007, 20:04:26

Název: mrznutí PC při 3d
Přispěvatel: ScH0ll_kIll3r 16 Listopadu 2007, 20:04:26

Dobry den mam takovy problem, vzdy kdyz ma system sahnout na 3d acc (beryl, compiz, cs atd....) tak me uplne vytuhne system, pridavam vypisy

xorg.conf

Kód: [Vybrat]

# xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
EndSection

Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "cz"
EndSection

Section "InputDevice"
        Identifier  "Configured Mouse"
        Driver      "mouse"
        Option      "CorePointer"
        Option      "Device" "/dev/input/mice"
        Option      "Protocol" "ExplorerPS/2"
        Option      "ZAxisMapping" "4 5"
        Option      "ButtonMapping" "1 2 3 6 7"
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection

Section "Device"
        Identifier      "Radeon 9200SE"
        Driver          "ati"
        BusID           "PCI:1:0:0"
        Option          "XAANoOffscreenPixmaps"
EndSection

Section "Monitor"
Identifier "C15-2"
Option "DPMS"
EndSection

Section "Screen"
Identifier "Default Screen"
Device "Radeon 9200SE"
Monitor "C15-2"
DefaultDepth 16
SubSection "Display"
Modes "1024x768" "800x600" "720x400" "640x480"
EndSubSection
EndSection

Section "ServerLayout"
        Option          "AIGLX"         "true"
        Identifier      "Default Layout"
        Screen          "Default Screen"
        InputDevice     "Generic Keyboard"
        InputDevice     "Configured Mouse"


# Uncomment if you have a wacom tablet
# InputDevice     "stylus" "SendCoreEvents"
# InputDevice     "cursor" "SendCoreEvents"
# InputDevice     "eraser" "SendCoreEvents"
EndSection

Section "DRI"
        Mode 0666
EndSection

Section "Extensions"
        Option "Composite" "Enable"
EndSection

Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "vbe"
EndSection


Kód: [Vybrat]

schollkiller@desktop:~$ lspci -nn | grep VGA
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon 9200 SE] [1002:5964] (rev 01)


Kód: [Vybrat]

schollkiller@desktop:~$ glxinfo |grep vendor
server glx vendor string: SGI
client glx vendor string: SGI
OpenGL vendor string: Tungsten Graphics, Inc.
schollkiller@desktop:~$


Kód: [Vybrat]

schollkiller@desktop:~$ glxinfo | grep "direct rendering"
direct rendering: Yes

Diky za rady...