Fórum Ubuntu CZ/SK
Ostatní => Archiv => Téma založeno: the.geremy 24 Července 2008, 19:08:00
-
Ahoj, uz sa asi 5 dni trapim s rozchodenim wifi :( nejak to nejde som v linuxe novacik a skusal som uz vela navodov a nic. Ak viete poradit budem rad:
nejake info po zadani lshw -C network:
*-network UNCLAIMED
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:02:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:05:00.0
logical name: eth0
version: 01
serial: 00:1d:92:4b:1d:e9
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.10.8 latency=0 link=yes module=r8169 multicast=yes port=twisted pair speed=100MB/s
po iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
po dmesg | egrep 'ath|wifi|hal':
[ 41.849274] ath_hal: module license 'Proprietary' taints kernel.
[ 41.860060] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 42.205882] ath_pci: 0.9.4
[ 42.262992] wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
verzia mad wifi je 9.0.3.3 a su tam nainstalovane non free drivers pre wifi:
Atheros HAL
Support for Atheros 802.11 wireless LAN cards
-
Máš povolené nesvobodné ovladače přes Správce? Mě to připadá, že ne... Že se ti sice v systému ukážou, ale nejsou povolené...
Jinak mám stejnou verzi Atherosu a Ubuntu 8.04.1 s jádrem 2.6.24-20-generic a funguje mi to bez problémů hned po první instalaci HH!
-
Co je to niekolko navodov? Akych? Ak si skusal madwifi dal si ho aj rucne zaviest?
sudo modprobe ath_pci
Ja mam instalovane podla tohto
http://www.ubuntugeek.com/atheros-5007eg-with-madwifi-on-i386-platform.html
-
ovladace su povolene isto :)
a kde si zohnal istalaciu ubuntu s tym jadrom :)???
aj som skusal zavies rucne madwifi aj novsiu verziu ale tvarilo sa to rovnako aj po zavedeni :)
a skusal som to aj cez ndiswrapper a stale nic
ja potrebujem nejaky pokial mozno velmi jednoduchy navod zatial sa len ucim s linuxami sa kamosim asi tak tyzden :D
skusim to podla toho linku co si tu dal a uvidime ale asi az zajtra na dnes mam toho dost :)
-
Ja som tu stiahol ovladace
http://snapshots.madwifi.org/special/madwifi-nr-r3366+ar5007.tar.gz
rozbalil som ich do home cim vznikol adresar madwifi-nr-r3366+ar5007.
Otvoris terminal (aplikacie-prislusenstvo-terminal) a zadas prikaz ktori ta prepne do toho adresara
cd madwifi-nr-r3366+ar5007doinstalujes potrebne veci
sudo apt-get update && sudo aptitude install build-essentiala spustis instalaciu
sudo make installa aktivujes ju
sudo modprobe ath_pcipo tomto by sa ti mala zobrazit wifi karta
$ ifconfig
ath0 Link encap:Ethernet HWaddr 00:15:af:46:30:95
inet6 addr: fe80::215:afff:fe46:3095/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 00:1d:60:b8:21:e0
inet addr:192.168.100.100 Bcast:192.168.100.255 Mask:255.255.255.0
inet6 addr: fe80::21d:60ff:feb8:21e0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:53162 errors:0 dropped:0 overruns:0 frame:0
TX packets:47409 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:69382777 (66.1 MB) TX bytes:4856458 (4.6 MB)
Interrupt:218 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:887 errors:0 dropped:0 overruns:0 frame:0
TX packets:887 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:40942 (39.9 KB) TX bytes:40942 (39.9 KB)
wifi0 Link encap:UNSPEC HWaddr 00-15-AF-46-30-95-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:907 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:195
RX bytes:0 (0.0 B) TX bytes:41122 (40.1 KB)
Interrupt:20 Samozrejme pred tym musis vypnut oba ovladace v system-sprava-ovladace hardveru.
-
no tak som to skusil :( na konci ked zadam ifconfig dostanem toto:
eth0 Link encap:Ethernet HWaddr 00:1d:92:4b:1d:e9
inet addr:192.168.10.8 Bcast:192.168.10.255 Mask:255.255.255.0
inet6 addr: fe80::21d:92ff:fe4b:1de9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7223 errors:0 dropped:0 overruns:0 frame:0
TX packets:4690 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:9415488 (8.9 MB) TX bytes:345362 (337.2 KB)
Interrupt:252 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:170 errors:0 dropped:0 overruns:0 frame:0
TX packets:170 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8500 (8.3 KB) TX bytes:8500 (8.3 KB)
takze to nefunguje kua! :( dalsi vypis hovori ze ju stale nepozna:
jozef@jozef-lbook:~$ sudo lshw -C network
[sudo] password for jozef:
*-network UNCLAIMED
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:02:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:05:00.0
logical name: eth0
version: 01
serial: 00:1d:92:4b:1d:e9
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.10.8 latency=0 link=yes module=r8169 multicast=yes port=twisted pair speed=100MB/s
predtym mi na dmesg | egrep 'ath|wifi|hal' pisalo toto:
[ 41.849274] ath_hal: module license 'Proprietary' taints kernel.
[ 41.860060] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 42.205882] ath_pci: 0.9.4
[ 42.262992] wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
teraz to nevypise nic tak neviem ci to ma s tym nieco spolocne ale aj tak tu kartu wifi nie je v systeme vidiet :(
-
myslim ze ja mam ten isty problem,
mam Kubuntu a tu istu karty a docital som sa ze madwifi s tym patchom nepracuje s 64bit ubuntu. Nevie niekto pomoct?
-
ovladace su povolene isto :)
a kde si zohnal istalaciu ubuntu s tym jadrom :)???
http://www.edisk.cz/stahnout-soubor/57245/Obrazovka-2.png_98.17KB.html
Normálně jsem stáhnul nejnovější verzi Hardyho z netu, tj. 8.04.1 a jádro se mi aktualizovalo na 2.6.24-20-generic
-
skus to podla tohto http://ubuntuforums.org/showthread.php?t=512828 (http://ubuntuforums.org/showthread.php?t=512828)
-
pro UBUNTU 8.4 kernel 2.6.24-20 staci oznacit ve zdrojich hardy-nevydane
-
to som spravil ale stale nefunguje..
-
urobil som to podla navodu na ndiswrapper uz vidim wifi kartu v systeme a viem ju aj nastavovat ale nechce sa prihlasit k sieti :) zda sa ze nejak nevysiela ako keby bola vypnuta :( aj ked niekedy mi zobrazuje ze vidi siet a aj jej silu ale ked dam prihlasit tak to nejde :(
ifconfig pise toto:
eth0 Link encap:Ethernet HWaddr 00:1d:92:4b:1d:e9
inet addr:190.160.100.5 Bcast:190.160.100.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:120 errors:0 dropped:0 overruns:0 frame:0
TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:34083 (33.2 KB) TX bytes:4327 (4.2 KB)
Interrupt:252 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:175 errors:0 dropped:0 overruns:0 frame:0
TX packets:175 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9088 (8.8 KB) TX bytes:9088 (8.8 KB)
wlan0 Link encap:Ethernet HWaddr 00:15:af:86:3e:00
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:16 Memory:fdff0000-fe000000
odoslane a prijate data su nulove co nejak nesedi pri prihlasovani sa predsa len nejake data poslat musia nie? :D
kartu uz pozna prikaz lshw -C network dava:
*-network
description: Wireless interface
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlan0
version: 01
serial: 00:15:af:86:3e:00
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=ndiswrapper+net5211 driverversion=1.51+,06/21/2007,5.3.0.56 latency=0 link=no module=ndiswrapper multicast=yes wireless=IEEE 802.11g