Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Internet a sítě => Téma založeno: radek.juthner 06 Srpna 2008, 18:52:36
-
Pravděpodobně nějakým upgradem mého Hardy Heron se objevila potíž s wifinou: mám implicitně na notebooku nastavenou síť přes Wifi notebooku. Jenže někdy při zapnutí NB "naskočí" a jindy ne. To stejný se děje i přes rstarrt síťovky přes příkazový řádek: někdy naskočí někdy ne.
Nevíte, kde by mohl být problém? Navíc při použití sudo /etc/init.d/networking restart dostávám přehršle informací, než bylo dříve. Dík za případné rady.
-
To má být dotaz pro majitele křišťálové koule?
lshw
lspci --vn
lsusb
dmesg
ifconfig
iwconfig
-
Sorry
Z kterýho z těch příkazů něco zásadního vyčteš? Je toho mrtě stránek.
-
Copa máš za síťovku? Podobné problémy mám na noťasu s fakt úžasnou wifinou od Broadcomu. By člověk blil...
-
Copa máš za síťovku? Podobné problémy mám na noťasu s fakt úžasnou wifinou od Broadcomu. By člověk blil...
Včera sem tu svini odnes do bazaru a koupil atheros ;D
-
Sorry
Z kterýho z těch příkazů něco zásadního vyčteš? Je toho mrtě stránek.
No protože odmítáte prozdradit cokoliv o vašem HW tak se
1) lshw podívám co máte za HW, a při troše štestí uvidím i síťovku
2) lspci -vn mi řekne podrobnější informace pokud ji máte v pci slotu
3) lsusb dtto pokud je ta síťovka připojená v usb
4) dmesg uvidím jestli se s ní jádro pokusilo něco udělat a třeba případný výpis proč se to nepovedlo
5) kdyby náhodou byla ale nemohla získat adresu tak se tam objeví avahi rozhraní
6) iwconfig - protože je to wifina tak mi poví víc v jakém stavu se nachází
Je sice hezké že dostáváte spoustu informací i při restartu networkingu, ale pokud se o naprosto žádné informace nechcete podělit tak si problém asi budete muset vyřešit sám.
Protože bez informací nebo bez bez křišťálové koule můžu maximálně poradit ať se otočíte o půlnoci při úplňku k východu, pokřižujete se, uděláte dva kotouly a zkusíte tu síť restartovat znovu a možná pojede.
-
Posílám informace o sáťovce (alespoň ty, o kterých si myslím, že jsou k záležitosti relevantní)
- Nevím jestli mám kartu v PCI slotu, když mám notebook, stejně tak v USB.
- Avahi rozhraní se objevuje. Mám nainstalovaný sledování sítě a je fakt, že někdy se rozhraní označí jako eth1:avahi s nějakou mě neznámou IP adresou.
radek@RAJ:~$ lshw
WARNING: you should run this program as super-user.
raj
description: Computer
width: 32 bits
*-core
description: Motherboard
physical id: 0
*-memory
description: System memory
physical id: 0
size: 1001MiB
*-cpu
product: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz
vendor: Intel Corp.
physical id: 1
bus info: cpu@0
version: 6.15.2
serial: 0000-06F2-0000-0000-0000-0000
size: 1667MHz
capacity: 1667MHz
width: 64 bits
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx x86-64 constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm cpufreq
configuration: id=0
*-logicalcpu:0
description: Logical CPU
physical id: 0.1
width: 64 bits
capabilities: logical
*-logicalcpu:1
description: Logical CPU
physical id: 0.2
width: 64 bits
capabilities: logical
*-pci
description: Host bridge
product: Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub
vendor: Intel Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: 03
width: 32 bits
clock: 33MHz
configuration: driver=agpgart-intel module=intel_agp
*-display:0 UNCLAIMED
description: VGA compatible controller
product: Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller
vendor: Intel Corporation
physical id: 2
bus info: pci@0000:00:02.0
version: 03
width: 32 bits
clock: 33MHz
capabilities: vga_controller bus_master cap_list
configuration: latency=0
*-display:1 UNCLAIMED
description: Display controller
product: Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller
vendor: Intel Corporation
physical id: 2.1
bus info: pci@0000:00:02.1
version: 03
width: 32 bits
clock: 33MHz
capabilities: cap_list
configuration: latency=0
*-multimedia
description: Audio device
product: 82801G (ICH7 Family) High Definition Audio Controller
vendor: Intel Corporation
physical id: 1b
bus info: pci@0000:00:1b.0
version: 02
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list
configuration: driver=HDA Intel latency=0 module=snd_hda_intel
*-pci:0
description: PCI bridge
product: 82801G (ICH7 Family) PCI Express Port 1
vendor: Intel Corporation
physical id: 1c
bus info: pci@0000:00:1c.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master cap_list
configuration: driver=pcieport-driver
*-network
description: Ethernet interface
product: NetXtreme BCM5751M Gigabit Ethernet PCI Express
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 21
serial: 00:16:d3:b3:7b:d5
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=tg3 driverversion=3.86 firmware=5751m-v3.56 ip=192.168.1.226 latency=0 module=tg3 multicast=yes
*-pci:1
description: PCI bridge
product: 82801G (ICH7 Family) PCI Express Port 2
vendor: Intel Corporation
physical id: 1c.1
bus info: pci@0000:00:1c.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master cap_list
configuration: driver=pcieport-driver
*-network
description: Wireless interface
product: PRO/Wireless 3945ABG Network Connection
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:03:00.0
logical name: wmaster0
version: 02
serial: 00:1b:77:04:ad:7d
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list logical ethernet physical wireless
configuration: broadcast=yes driver=iwl3945 ip=10.0.0.2 latency=0 module=iwl3945 multicast=yes wireless=IEEE 802.11g
*-pci:2
description: PCI bridge
product: 82801G (ICH7 Family) PCI Express Port 3
vendor: Intel Corporation
physical id: 1c.2
bus info: pci@0000:00:1c.2
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master cap_list
configuration: driver=pcieport-driver
*-pci:3
description: PCI bridge
product: 82801G (ICH7 Family) PCI Express Port 4
vendor: Intel Corporation
physical id: 1c.3
bus info: pci@0000:00:1c.3
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master cap_list
configuration: driver=pcieport-driver
*-usb:0
description: USB Controller
product: 82801G (ICH7 Family) USB UHCI Controller #1
vendor: Intel Corporation
physical id: 1d
bus info: pci@0000:00:1d.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:1
description: USB Controller
product: 82801G (ICH7 Family) USB UHCI Controller #2
vendor: Intel Corporation
physical id: 1d.1
bus info: pci@0000:00:1d.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:2
description: USB Controller
product: 82801G (ICH7 Family) USB UHCI Controller #3
vendor: Intel Corporation
physical id: 1d.2
bus info: pci@0000:00:1d.2
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:3
description: USB Controller
product: 82801G (ICH7 Family) USB UHCI Controller #4
vendor: Intel Corporation
physical id: 1d.3
bus info: pci@0000:00:1d.3
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:4
description: USB Controller
product: 82801G (ICH7 Family) USB2 EHCI Controller
vendor: Intel Corporation
physical id: 1d.7
bus info: pci@0000:00:1d.7
version: 02
width: 32 bits
clock: 33MHz
capabilities: ehci bus_master cap_list
configuration: driver=ehci_hcd latency=0 module=ehci_hcd
*-pci:4
description: PCI bridge
product: 82801 Mobile PCI Bridge
vendor: Intel Corporation
physical id: 1e
bus info: pci@0000:00:1e.0
version: e2
width: 32 bits
clock: 33MHz
capabilities: pci subtractive_decode bus_master cap_list
*-pcmcia
description: CardBus bridge
product: PCIxx12 Cardbus Controller
vendor: Texas Instruments
physical id: 0
bus info: pci@0000:15:00.0
version: 00
width: 32 bits
clock: 33MHz
capabilities: pcmcia bus_master cap_list
configuration: driver=yenta_cardbus latency=176 maxlatency=5 mingnt=192 module=yenta_socket
*-firewire
description: FireWire (IEEE 1394)
product: PCIxx12 OHCI Compliant IEEE 1394 Host Controller
vendor: Texas Instruments
physical id: 0.1
bus info: pci@0000:15:00.1
version: 00
width: 32 bits
clock: 33MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci1394 latency=64 maxlatency=4 mingnt=2 module=ohci1394
*-isa
description: ISA bridge
product: 82801GBM (ICH7-M) LPC Interface Bridge
vendor: Intel Corporation
physical id: 1f
bus info: pci@0000:00:1f.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: isa bus_master cap_list
configuration: latency=0
*-ide
description: IDE interface
product: 82801G (ICH7 Family) IDE Controller
vendor: Intel Corporation
physical id: 1f.1
bus info: pci@0000:00:1f.1
logical name: scsi0
version: 02
width: 32 bits
clock: 33MHz
capabilities: ide bus_master emulated
configuration: driver=ata_piix latency=0 module=ata_piix
*-cdrom
description: DVD-RAM writer
product: DVD-RAM UJ-850
vendor: MATSHITA
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/cdrom
logical name: /dev/dvd
logical name: /dev/scd0
logical name: /dev/sr0
version: RB11
capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram
configuration: ansiversion=5 status=open
*-storage
description: SATA controller
product: 82801GBM/GHM (ICH7 Family) SATA AHCI Controller
vendor: Intel Corporation
physical id: 1f.2
bus info: pci@0000:00:1f.2
version: 02
width: 32 bits
clock: 66MHz
capabilities: storage ahci_1.0 bus_master cap_list
configuration: driver=ahci latency=0 module=ahci
*-serial UNCLAIMED
description: SMBus
product: 82801G (ICH7 Family) SMBus Controller
vendor: Intel Corporation
physical id: 1f.3
bus info: pci@0000:00:1f.3
version: 02
width: 32 bits
clock: 33MHz
configuration: latency=0
-
dmesg
[ 11.949273] SMP alternatives: switching to UP code
[ 11.950958] Early unpacking initramfs... done
[ 12.294642] ACPI: Core revision 20070126
[ 12.294712] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 12.322597] CPU0: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz stepping 02
[ 12.322614] SMP alternatives: switching to SMP code
[ 12.323360] Booting processor 1/1 eip 3000
[ 12.333895] Initializing CPU#1
[ 12.412457] Calibrating delay using timer specific routine.. 3325.02 BogoMIPS (lpj=6650059)
[ 12.412464] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[ 12.412470] monitor/mwait feature present.
[ 12.412473] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 12.412475] CPU: L2 cache: 2048K
[ 12.412477] CPU: Physical Processor ID: 0
[ 12.412478] CPU: Processor Core ID: 1
[ 12.412479] CPU: After all inits, caps: bfebfbff 20100000 00000000 00043940 0000e3bd 00000000 00000001 00000000
[ 12.412781] CPU1: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz stepping 02
[ 12.412805] Total of 2 processors activated (6653.94 BogoMIPS).
[ 12.413001] ENABLING IO-APIC IRQs
[ 12.413193] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 12.560038] checking TSC synchronization [CPU#0 -> CPU#1]:
[ 12.580016] Measured 514390 cycles TSC warp between CPUs, turning off TSC clock.
[ 12.580018] Marking TSC unstable due to: check_tsc_sync_source failed.
[ 12.580031] Brought up 2 CPUs
[ 12.580056] CPU0 attaching sched-domain:
[ 12.580058] domain 0: span 03
[ 12.580060] groups: 01 02
[ 12.580063] CPU1 attaching sched-domain:
[ 12.580065] domain 0: span 03
[ 12.580067] groups: 02 01
[ 12.580625] net_namespace: 64 bytes
[ 12.580632] Booting paravirtualized kernel on bare hardware
[ 12.581108] Time: 6:32:52 Date: 08/07/08
[ 12.581136] NET: Registered protocol family 16
[ 12.581349] EISA bus registered
[ 12.581354] ACPI: bus type pci registered
[ 12.581543] PCI: PCI BIOS revision 2.10 entry at 0xfd82b, last bus=24
[ 12.581545] PCI: Using configuration type 1
[ 12.581554] Setting up standard PCI resources
[ 12.585682] ACPI: EC: EC description table is found, configuring boot EC
[ 12.593227] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 12.597466] ACPI: Interpreter enabled
[ 12.597469] ACPI: (supports S0 S3 S4 S5)
[ 12.597484] ACPI: Using IOAPIC for interrupt routing
[ 12.606751] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 12.606754] ACPI: EC: driver started in poll mode
[ 12.606943] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 12.607828] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 12.607832] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 12.609132] PCI: Transparent bridge - 0000:00:1e.0
[ 12.609235] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 12.609415] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
[ 12.609548] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 12.609681] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 12.609815] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 12.609950] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 12.613147] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.613373] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.613596] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.613818] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.614040] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.614262] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.614483] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.614705] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[ 12.615111] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 12.615327] ACPI: Power Resource [PUBS] (on)
[ 12.615396] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 12.615431] pnp: PnP ACPI init
[ 12.615439] ACPI: bus type pnp registered
[ 12.616761] pnpacpi: exceeded the max number of mem resources: 12
[ 12.620512] pnp: PnP ACPI: found 11 devices
[ 12.620514] ACPI: ACPI bus type pnp unregistered
[ 12.620517] PnPBIOS: Disabled by ACPI PNP
[ 12.621086] PCI: Using ACPI for IRQ routing
[ 12.621089] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 12.704151] NET: Registered protocol family 8
[ 12.704153] NET: Registered protocol family 20
[ 12.704192] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 12.704197] hpet0: 3 64-bit timers, 14318180 Hz
[ 12.705232] AppArmor: AppArmor Filesystem Enabled
[ 12.707704] Time: hpet clocksource has been installed.
[ 12.707721] Switched to high resolution mode on CPU 0
[ 12.708143] Switched to high resolution mode on CPU 1
[ 12.720690] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 12.720694] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[ 12.720697] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[ 12.720699] system 00:00: iomem range 0xc8000-0xcbfff has been reserved
[ 12.720702] system 00:00: iomem range 0xcc000-0xcffff could not be reserved
[ 12.720705] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
[ 12.720707] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 12.720710] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 12.720713] system 00:00: iomem range 0xdc000-0xdffff has been reserved
[ 12.720715] system 00:00: iomem range 0xe0000-0xe3fff has been reserved
[ 12.720718] system 00:00: iomem range 0xe4000-0xe7fff has been reserved
[ 12.720720] system 00:00: iomem range 0xe8000-0xebfff has been reserved
[ 12.720727] system 00:02: ioport range 0x164e-0x164f has been reserved
[ 12.720730] system 00:02: ioport range 0x1000-0x107f has been reserved
[ 12.720732] system 00:02: ioport range 0x1180-0x11bf has been reserved
[ 12.720735] system 00:02: ioport range 0x800-0x80f has been reserved
[ 12.720738] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[ 12.720740] system 00:02: ioport range 0x1600-0x165f could not be reserved
[ 12.720744] system 00:02: iomem range 0xf0000000-0xf3ffffff could not be reserved
[ 12.720747] system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved
[ 12.720750] system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
[ 12.720752] system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
[ 12.720755] system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
[ 12.751200] PCI: Bridge: 0000:00:1c.0
[ 12.751202] IO window: disabled.
[ 12.751208] MEM window: ee000000-ee0fffff
[ 12.751213] PREFETCH window: disabled.
[ 12.751219] PCI: Bridge: 0000:00:1c.1
[ 12.751222] IO window: 2000-3fff
[ 12.751228] MEM window: ec000000-edffffff
[ 12.751232] PREFETCH window: e4000000-e40fffff
[ 12.751239] PCI: Bridge: 0000:00:1c.2
[ 12.751242] IO window: 4000-5fff
[ 12.751248] MEM window: e8000000-e9ffffff
[ 12.751252] PREFETCH window: e4100000-e41fffff
[ 12.751258] PCI: Bridge: 0000:00:1c.3
[ 12.751261] IO window: 6000-7fff
[ 12.751267] MEM window: ea000000-ebffffff
[ 12.751271] PREFETCH window: e4200000-e42fffff
[ 12.751280] PCI: Bus 22, cardbus bridge: 0000:15:00.0
[ 12.751282] IO window: 00008000-000080ff
[ 12.751288] IO window: 00008400-000084ff
[ 12.751293] PREFETCH window: e0000000-e3ffffff
[ 12.751299] MEM window: 50000000-53ffffff
[ 12.751305] PCI: Bridge: 0000:00:1e.0
[ 12.751308] IO window: 8000-bfff
[ 12.751314] MEM window: e4300000-e7ffffff
[ 12.751318] PREFETCH window: e0000000-e3ffffff
[ 12.751350] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 12.751356] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 12.751381] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 17
[ 12.751387] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 12.751412] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 18
[ 12.751417] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 12.751441] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 19
[ 12.751447] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 12.751459] PCI: Enabling device 0000:00:1e.0 (0005 -> 0007)
[ 12.751465] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 12.751485] ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 12.751499] NET: Registered protocol family 2
[ 12.795594] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 12.795820] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 12.796288] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 12.796518] TCP: Hash tables configured (established 131072 bind 65536)
[ 12.796521] TCP reno registered
[ 12.807648] checking if image is initramfs... it is
[ 13.484329] Freeing initrd memory: 7327k freed
[ 13.484498] Simple Boot Flag at 0x35 set to 0x1
[ 13.485545] audit: initializing netlink socket (disabled)
[ 13.485559] audit(1218090772.488:1): initialized
[ 13.485453] highmem bounce pool size: 64 pages
[ 13.487999] VFS: Disk quotas dquot_6.5.1
[ 13.487777] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 13.487918] io scheduler noop registered
[ 13.487921] io scheduler anticipatory registered
[ 13.487923] io scheduler deadline registered
[ 13.487934] io scheduler cfq registered (default)
[ 13.487946] Boot video device is 0000:00:02.0
[ 13.488164] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 13.488224] assign_interrupt_mode Found MSI capability
[ 13.488274] Allocate Port Service[0000:00:1c.0:pcie00]
[ 13.488314] Allocate Port Service[0000:00:1c.0:pcie02]
[ 13.488421] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 13.488480] assign_interrupt_mode Found MSI capability
[ 13.488528] Allocate Port Service[0000:00:1c.1:pcie00]
[ 13.488564] Allocate Port Service[0000:00:1c.1:pcie02]
[ 13.488671] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 13.488730] assign_interrupt_mode Found MSI capability
[ 13.488777] Allocate Port Service[0000:00:1c.2:pcie00]
[ 13.488815] Allocate Port Service[0000:00:1c.2:pcie02]
[ 13.488925] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 13.488984] assign_interrupt_mode Found MSI capability
[ 13.489032] Allocate Port Service[0000:00:1c.3:pcie00]
[ 13.489071] Allocate Port Service[0000:00:1c.3:pcie02]
[ 13.489361] isapnp: Scanning for PnP cards...
[ 13.843493] isapnp: No Plug & Play device found
[ 13.871447] Real Time Clock Driver v1.12ac
[ 13.871565] hpet_resources: 0xfed00000 is busy
[ 13.871614] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 13.872977] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 13.873052] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 13.873163] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 13.882060] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 13.882065] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 13.901880] mice: PS/2 mouse device common for all mice
[ 13.902006] EISA: Probing bus 0 at eisa.0
[ 13.902013] Cannot allocate resource for EISA slot 1
[ 13.902016] Cannot allocate resource for EISA slot 2
[ 13.902018] Cannot allocate resource for EISA slot 3
[ 13.902020] Cannot allocate resource for EISA slot 4
[ 13.902022] Cannot allocate resource for EISA slot 5
[ 13.902024] Cannot allocate resource for EISA slot 6
[ 13.902026] Cannot allocate resource for EISA slot 7
[ 13.902028] Cannot allocate resource for EISA slot 8
[ 13.902029] EISA: Detected 0 cards.
[ 13.902032] cpuidle: using governor ladder
[ 13.902034] cpuidle: using governor menu
[ 13.902118] NET: Registered protocol family 1
[ 13.902150] Using IPI No-Shortcut mode
[ 13.902180] registered taskstats version 1
[ 13.902299] Magic number: 4:648:518
[ 13.902372] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 13.902382] EDD information not available.
[ 13.902573] Freeing unused kernel memory: 368k freed
[ 13.905669] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 15.131104] fuse init (API version 7.9)
[ 15.154195] ACPI: SSDT 3F6F1D36, 0240 (r1 PmRef Cpu0Ist 100 INTL 20050513)
[ 15.154507] ACPI: SSDT 3F6F1FFB, 065A (r1 PmRef Cpu0Cst 100 INTL 20050513)
[ 15.158390] Monitor-Mwait will be used to enter C-1 state
[ 15.158393] Monitor-Mwait will be used to enter C-2 state
[ 15.158395] Monitor-Mwait will be used to enter C-3 state
[ 15.158532] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 15.158537] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 15.158773] ACPI: SSDT 3F6F1C6E, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513)
[ 15.159061] ACPI: SSDT 3F6F1F76, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513)
[ 15.162288] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 15.162294] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 15.165361] ACPI: Thermal Zone [THM0] (30 C)
[ 15.166979] ACPI: Thermal Zone [THM1] (30 C)
[ 15.534618] tg3.c:v3.86 (November 9, 2007)
[ 15.534644] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 15.534657] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 15.576669] eth0: Tigon3 [partno(BCM95751m) rev 4201 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:16:d3:b3:7b:d5
[ 15.576677] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 15.576680] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 15.577601] usbcore: registered new interface driver usbfs
[ 15.577625] usbcore: registered new interface driver hub
[ 15.577654] usbcore: registered new device driver usb
[ 15.578838] USB Universal Host Controller Interface driver v3.0
[ 15.578888] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 15.578899] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 15.578903] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 15.579122] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 15.579154] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
[ 15.579295] usb usb1: configuration #1 chosen from 1 choice
[ 15.579320] hub 1-0:1.0: USB hub found
[ 15.579325] hub 1-0:1.0: 2 ports detected
[ 15.630165] SCSI subsystem initialized
[ 15.683704] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 21
[ 15.683717] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 15.683721] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 15.683748] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 15.683780] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001840
[ 15.683893] usb usb2: configuration #1 chosen from 1 choice
[ 15.683917] hub 2-0:1.0: USB hub found
[ 15.683922] hub 2-0:1.0: 2 ports detected
[ 15.709881] libata version 3.00 loaded.
[ 15.787531] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 22
[ 15.787544] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 15.787549] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 15.787573] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 15.787604] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00001860
[ 15.787724] usb usb3: configuration #1 chosen from 1 choice
[ 15.787749] hub 3-0:1.0: USB hub found
[ 15.787754] hub 3-0:1.0: 2 ports detected
[ 15.891357] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 23
[ 15.891370] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 15.891375] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 15.891402] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 15.891433] uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001880
[ 15.891554] usb usb4: configuration #1 chosen from 1 choice
[ 15.891579] hub 4-0:1.0: USB hub found
[ 15.891584] hub 4-0:1.0: 2 ports detected
[ 15.923212] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 15.996076] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 23
[ 15.996092] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 15.996096] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 15.996124] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 16.000026] ehci_hcd 0000:00:1d.7: debug port 1
[ 16.000033] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 16.000039] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xee444000
[ 16.051005] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 16.051125] usb usb5: configuration #1 chosen from 1 choice
[ 16.051150] hub 5-0:1.0: USB hub found
[ 16.051156] hub 5-0:1.0: 8 ports detected
[ 16.134343] ata_piix 0000:00:1f.1: version 2.12
[ 16.134362] ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) -> IRQ 20
[ 16.134398] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 16.135032] scsi0 : ata_piix
[ 16.135568] scsi1 : ata_piix
[ 16.136352] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[ 16.136356] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 16.163632] usb 1-1: device not accepting address 2, error -71
[ 16.165835] ata1.00: ATAPI: MATSHITADVD-RAM UJ-850, RB11, max UDMA/33
[ 16.166032] Clocksource tsc unstable (delta = -323519467 ns)
[ 16.174421] ata1.00: configured for UDMA/33
[ 16.174505] ata2: port disabled. ignoring.
[ 16.175528] scsi 0:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-850 RB11 PQ: 0 ANSI: 5
[ 16.176165] PCI: Enabling device 0000:15:00.1 (0000 -> 0002)
[ 16.176172] ACPI: PCI Interrupt 0000:15:00.1[B] -> GSI 17 (level, low) -> IRQ 21
[ 16.176183] PCI: Setting latency timer of device 0000:15:00.1 to 64
[ 16.225839] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[e4301000-e43017ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 16.226660] ahci 0000:00:1f.2: version 3.0
[ 16.226687] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 20
[ 16.226733] ahci 0000:00:1f.2: nr_ports (4) and implemented port map (0x1) don't match, using nr_ports
[ 16.226736] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
[ 16.269057] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode
[ 16.269061] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[ 16.269067] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 16.269332] scsi2 : ahci
[ 16.269544] scsi3 : ahci
[ 16.269703] scsi4 : ahci
[ 16.269859] scsi5 : ahci
[ 16.269931] ata3: SATA max UDMA/133 abar m1024@0xee444400 port 0xee444500 irq 219
[ 16.269935] ata4: SATA max UDMA/133 abar m1024@0xee444400 port 0xee444580 irq 219
[ 16.269938] ata5: SATA max UDMA/133 abar m1024@0xee444400 port 0xee444600 irq 219
[ 16.269942] ata6: SATA max UDMA/133 abar m1024@0xee444400 port 0xee444680 irq 219
[ 16.281885] usb 1-1: new low speed USB device using uhci_hcd and address 4
[ 16.334853] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 16.336003] ata3.00: ATA-7: HTS541080G9SA00, MB4IC65R, max UDMA/100
[ 16.336005] ata3.00: 156301488 sectors, multi 16: LBA48
[ 16.337441] ata3.00: configured for UDMA/100
[ 16.338007] usb 1-1: configuration #1 chosen from 1 choice
[ 16.365924] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 16.368014] ata4: SATA link down (SStatus 0 SControl 0)
[ 16.373471] usb 3-1: configuration #1 chosen from 1 choice
[ 16.396185] ata5: SATA link down (SStatus 0 SControl 0)
[ 16.399205] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 16.406234] usb 4-1: configuration #1 chosen from 1 choice
[ 16.439812] ata6: SATA link down (SStatus 0 SControl 0)
[ 16.440310] scsi 2:0:0:0: Direct-Access ATA HTS541080G9SA00 MB4I PQ: 0 ANSI: 5
[ 16.454723] Driver 'sd' needs updating - please use bus_type methods
[ 16.456217] Driver 'sr' needs updating - please use bus_type methods
[ 16.459302] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 16.459323] sd 2:0:0:0: [sda] Write Protect is off
[ 16.459327] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 16.459356] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 16.459436] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 16.459454] sd 2:0:0:0: [sda] Write Protect is off
[ 16.459458] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 16.459486] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 16.459491] sda:sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 16.462567] Uniform CD-ROM driver Revision: 3.20
[ 16.462614] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 16.590643] usb 4-2: new full speed USB device using uhci_hcd and address 3
[ 16.762896] usb 4-2: configuration #1 chosen from 1 choice
[ 16.764933] usbcore: registered new interface driver hiddev
[ 16.779246] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input2
[ 16.798363] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 16.828031] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.1/input/input3
[ 16.829785] sda1 sda2 <<6>input,hiddev96,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 16.851622] sda5 >
[ 16.851730] sd 2:0:0:0: [sda] Attached SCSI disk
[ 16.856448] input: KEYBOARD as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input4
[ 16.858124] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 16.858145] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 16.883530] input,hidraw2: USB HID v1.10 Keyboard [KEYBOARD] on usb-0000:00:1d.2-1
[ 16.895861] input: KEYBOARD as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.1/input/input5
[ 16.918164] input,hidraw3: USB HID v1.10 Device [KEYBOARD] on usb-0000:00:1d.2-1
[ 16.918188] usbcore: registered new interface driver usbhid
[ 16.918192] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 17.070071] Attempting manual resume
[ 17.070075] swsusp: Resume From Partition 8:5
[ 17.070076] PM: Checking swsusp image.
[ 17.070249] PM: Resume from disk failed.
[ 17.117307] kjournald starting. Commit interval 5 seconds
[ 17.117021] EXT3-fs: mounted filesystem with ordered data mode.
[ 29.494656] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 29.617395] Linux agpgart interface v0.102
[ 29.665157] agpgart: Detected an Intel 945GM Chipset.
[ 29.666184] agpgart: Detected 7932K stolen memory.
[ 29.681346] agpgart: AGP aperture is 256M @ 0xd0000000
[ 29.725673] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 29.817123] intel_rng: FWH not detected
[ 29.905033] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 29.988616] Non-volatile memory driver v1.2
[ 30.204342] input: Power Button (FF) as /devices/virtual/input/input7
[ 30.255125] ACPI: Power Button (FF) [PWRF]
[ 30.255194] input: Lid Switch as /devices/virtual/input/input8
[ 30.271513] ACPI: Lid Switch [liD]
[ 30.271576] input: Sleep Button (CM) as /devices/virtual/input/input9
[ 30.300513] thinkpad_acpi: ThinkPad ACPI Extras v0.17
[ 30.300516] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 30.300518] thinkpad_acpi: ThinkPad BIOS 7CETC6WW (2.16 ), EC 7CHT21WW-1.09
[ 30.300520] thinkpad_acpi: Lenovo ThinkPad R60
[ 30.301153] thinkpad_acpi: radio switch found; radios are enabled
[ 30.334988] ACPI: Sleep Button (CM) [SLPB]
[ 30.336438] iTCO_vendor_support: vendor-support=0
[ 30.338106] thinkpad_acpi: standard ACPI backlight interface available, not loading native one...
[ 30.338371] input: ThinkPad Extra Buttons as /devices/virtual/input/input10
[ 30.356450] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 30.356541] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[ 30.356579] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 30.416594] Yenta: CardBus bridge found at 0000:15:00.0 [17aa:202f]
[ 30.416620] Yenta: Enabling burst memory read transactions
[ 30.416627] Yenta: Using INTVAL to route CSC interrupts to PCI
[ 30.416629] Yenta: Routing CardBus interrupts to PCI
[ 30.416635] Yenta TI: socket 0000:15:00.0, mfunc 0x01001b22, devctl 0x64
[ 30.545485] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input11
[ 30.586598] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 30.588328] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/LNXVIDEO:01/input/input12
[ 30.651329] Yenta: ISA IRQ mask 0x0cf8, PCI irq 20
[ 30.651334] Socket status: 30000086
[ 30.651338] pcmcia: parent PCI bridge I/O window: 0x8000 - 0xbfff
[ 30.651341] cs: IO port probe 0x8000-0xbfff: clean.
[ 30.652449] pcmcia: parent PCI bridge Memory window: 0xe4300000 - 0xe7ffffff
[ 30.652452] pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe3ffffff
[ 30.652500] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 30.812808] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.0
[ 30.812812] iwl3945: Copyright(c) 2003-2007 Intel Corporation
[ 30.812955] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 21
[ 30.812971] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 30.812995] iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
[ 30.860680] ACPI: AC Adapter [AC] (on-line)
[ 31.152984] ACPI: Battery Slot [BAT0] (battery present)
[ 31.306698] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04793/0x300000
[ 31.306704] serio: Synaptics pass-through port at isa0060/serio1/input0
[ 31.307107] ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 21
[ 31.307112] hda_intel: probe_mask set to 0x1 for device 17aa:2010
[ 31.307135] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 31.346203] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input13
[ 31.391089] Bluetooth: Core ver 2.11
[ 31.405795] NET: Registered protocol family 31
[ 31.405798] Bluetooth: HCI device and connection manager initialized
[ 31.405803] Bluetooth: HCI socket layer initialized
[ 31.445937] Bluetooth: HCI USB driver ver 2.9
[ 31.447711] usbcore: registered new interface driver hci_usb
[ 31.924341] NET: Registered protocol family 10
[ 31.924581] lo: Disabled Privacy Extensions
[ 31.924950] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 32.495500] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 32.517121] wmaster0: Selected rate control algorithm 'iwl-3945-rs'
[ 32.637282] udev: renamed network interface wlan0 to eth1
[ 32.647713] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 32.745887] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 32.745891] tg3: eth0: Flow control is off for TX and off for RX.
[ 32.747963] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 32.754752] cs: IO port probe 0x100-0x3af: clean.
[ 32.757066] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 32.758037] cs: IO port probe 0x820-0x8ff: clean.
[ 32.758849] cs: IO port probe 0xc00-0xcf7: clean.
[ 32.759819] cs: IO port probe 0xa00-0xaff: clean.
[ 32.950500] lp: driver loaded but no devices found
[ 33.086300] Adding 3004112k swap on /dev/sda5. Priority:-1 extents:1 across:3004112k
[ 33.585954] EXT3 FS on sda1, internal journal
[ 33.824344] NET: Registered protocol family 17
[ 34.592382] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.036939] ACPI: ACPI Dock Station Driver
[ 35.119068] ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay
[ 35.119075] ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Adding notify handler
[ 35.119114] ACPI: Error installing bay notify handler
[ 35.119119] ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added
[ 36.162057] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 36.369689] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input14
[ 36.577557] ppdev: user-space parallel port driver
[ 36.901076] audit(1218090799.563:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5406 profile="/usr/sbin/cupsd" namespace="default"
[ 38.779740] apm: BIOS not found.
[ 39.303095] input: /usr/sbin/thinkpad-keys as /devices/virtual/input/input15
[ 42.666366] eth0: no IPv6 routers present
[ 43.234022] Bluetooth: L2CAP ver 2.9
[ 43.234029] Bluetooth: L2CAP socket layer initialized
[ 43.291667] Bluetooth: RFCOMM socket layer initialized
[ 43.291682] Bluetooth: RFCOMM TTY layer initialized
[ 43.291685] Bluetooth: RFCOMM ver 1.8
[ 45.915229] [drm] Initialized drm 1.1.0 20060810
[ 45.963588] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 45.963602] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 45.963686] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 48.091518] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 74.664434] CPU0 attaching NULL sched-domain.
[ 74.664441] CPU1 attaching NULL sched-domain.
[ 74.687844] CPU0 attaching sched-domain:
[ 74.687848] domain 0: span 03
[ 74.687850] groups: 01 02
[ 74.687853] CPU1 attaching sched-domain:
[ 74.687855] domain 0: span 03
[ 74.687857] groups: 02 01
[ 95.907599] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 95.943085] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 96.078898] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 96.078906] tg3: eth0: Flow control is off for TX and off for RX.
[ 96.082365] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 96.516232] eth0: no IPv6 routers present
[ 385.956218] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[ 447.780807] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 447.818651] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 447.956741] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 447.956749] tg3: eth0: Flow control is off for TX and off for RX.
[ 447.960228] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 450.464248] eth0: no IPv6 routers present
[ 562.233068] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 562.270619] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 562.402840] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 562.402847] tg3: eth0: Flow control is off for TX and off for RX.
[ 562.406310] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 562.980428] eth0: no IPv6 routers present
[ 593.702307] eth1: Initial auth_alg=0
[ 593.702316] eth1: authenticate with AP 00:02:cf:55:15:23
[ 593.703539] eth1: RX authentication from 00:02:cf:55:15:23 (alg=0 transaction=2 status=0)
[ 593.703546] eth1: authenticated
[ 593.703550] eth1: associate with AP 00:02:cf:55:15:23
[ 593.704804] eth1: RX AssocResp from 00:02:cf:55:15:23 (capab=0x401 status=0 aid=2)
[ 593.704824] eth1: associated
[ 593.708563] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 594.871815] eth1: no IPv6 routers present
radek@RAJ:~$ ifconfig
eth0 Link encap:Ethernet HWadr 00:16:d3:b3:7b:d5
inet adr:192.168.1.226 Všesměr:192.168.1.255 Maska:255.255.255.0
inet6-adr: fe80::216:d3ff:feb3:7bd5/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:2869 errors:0 dropped:0 overruns:0 frame:0
TX packets:589 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 395855 (386.5 KB) Odesláno bajtů: 83971 (82.0 KB)
Přerušení:20
eth1 Link encap:Ethernet HWadr 00:1b:77:04:ad:7d
inet adr:10.0.0.2 Všesměr:10.0.0.255 Maska:255.255.255.0
inet6-adr: fe80::21b:77ff:fe04:ad7d/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:155 errors:0 dropped:0 overruns:0 frame:0
TX packets:277 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 62612 (61.1 KB) Odesláno bajtů: 48169 (47.0 KB)
lo Link encap:Místní smyčka
inet adr:127.0.0.1 Maska:255.0.0.0
inet6-adr: ::1/128 Rozsah:Počítač
AKTIVOVÁNO SMYČKA BĚŽÍ MTU:16436 Metrika:1
RX packets:3180 errors:0 dropped:0 overruns:0 frame:0
TX packets:3180 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 157488 (153.7 KB) Odesláno bajtů: 157488 (153.7 KB)
wmaster0 Link encap:NEZNÁM HWadr 00-1B-77-04-AD-7D-00-00-00-00-00-00-00-00-00-00
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)
radek@RAJ:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
eth1 IEEE 802.11g ESSID:"default" Nickname:"default"
Mode:Managed Frequency:2.437 GHz Access Point: 00:02:CF:55:15:23
Bit Rate=12 Mb/s Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment thr=2346 B
Power Management:off
Link Quality=42/100 Signal level=-84 dBm Noise level=-94 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
-
Jen drobná technická - uzavírejte výpisy mezi tagy "code" tj. [ code ] a [ /code ] (bez mezer) ať se v tom pak dá vyznat
-
tohle je výpis když vám wifi běží, moc nepomůže.
Jinak koukám že standardní hardware - centrino, s wifi Intel PRO/Wireless 3945ABG
Měl jsem problémy pokud při startu ubuntu byl vypnutý hardwarový switch na vypínání wifi, tak pak už wifi nenaběhlo, "řešíval" jsem to restartem PC se zapnutým switchem pro wifi.
Koukám že máte ovladač iwl3945 verzi 1.2.0,
apt-get install linux-backports-modules-hardy-generic, pak restart.
obsahuje mimo jiného i iwl3945 verzi 1.2.25 (asi budete muset povolit ve zdrojích softwaru backports repozitář)
//edit:
Pokud by to v dmesg vypisovalo u iwl3945 něco ohledně vypnutého kill switche a vy jste ho měl přitom zaplý tak případně můžete zkusit:
sudo rmmod -f iwl3945
sudo modprobe iwl3945 disable_hw_scan=1
Někdo také míval problém kvůli network manageru, většinou jej nahrazovali WiCD, to ale spíše váš případ nebude.
-
iwlist scan
-
Tak to nějak nepomohlo: nastartoval jsem NB. Signál byl, ale nechytlo se dynamicky přidělovaný IP. To se chytlo až po restartu síťovky příkazem sudo /etc/init.d/networking restart
-
Copa máš za síťovku? Podobné problémy mám na noťasu s fakt úžasnou wifinou od Broadcomu. By člověk blil...
Co máš za notebook? Mě Broadcomm běhá výborně.