Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Pracovní prostředí => Téma založeno: Šuohob 14 Března 2009, 21:25:18
-
Dobrý den, mám starý notebook fujitsu siemens s integrovanou grafikou sis. Bohužel mi běží jen na rozlišení 800x600 (pravděpodobně ovladač VESA) a rozlišení nelze měnit na větší. Nejsem v ubuntu žádný borec a když jsem zkoušel ručně s návodem editovat xorg.conf, vždy jsem skončil s neúspěchem. Mohl by mi prosím někdo poradit, jak to mám nastavit, abych to měl použitelné? Je možné to vyřešit změnou ovladače, případně jaký tam nainstalovat? Na této grafice pravděpodobně asi nerozběhám 3D akceleraci, že?
Přikládám výpis lspci:
bohous@notes:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port (virtual PCI-to-PCI bridge)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02)
00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03)
00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller
00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter (rev 10)
02:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
Ještě nastavení xorg.conf, které tam bylo původně:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# Note that some configuration settings that could be done previously
# in this file, now are automatically configured by the server and settings
# here are ignored.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Device"
Identifier "Configured Video Device"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
EndSection
Děkuji
-
To mi skutečně nikdo neporadí?
-
Co máš za ubuntu? Co umí tvůj display?
-
Ubuntu mám 8.10 a display umí rozhodně víc, než 800x600. Kdysi jsem na notebooku měl win xp a rozlišení běželo mohlo běžet až na 1280x800, 32 bit. barvy, 60 Hz
-
mrkni se na thread http://ubuntuforums.org/showthread.php?t=615094 , resi to tam tenhle chipset na x stranach... jsou tam i nejake uryvky z xorg.conf
a na https://www.abclinuxu.cz/poradna/linux/show/224586 rikaji, ze v xorg.conf by se mel nastavit driver na sis
-
Dobrý den, pročetl jsem si ty fóra a trochu experimentoval.
xorg.conf jsem změnil na:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# Note that some configuration settings that could be done previously
# in this file, now are automatically configured by the server and settings
# here are ignored.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Device"
Identifier "Configured Video Device"
Driver "vesa"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
HorizSync 30-107
VertRefresh 50-185
Modeline "1024x768_60.00" 64.11 1024 1080 1184 1344 768 769 772 795 -HSync +Vsync
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
EndSection
Rozlišení mi teď funguje docela slušně na 1024x768 a 1280x768. Ale bohužel to pořád šlape na ovladači vesa, takže 3D akcelerace v podstatě žádná, Extreme Tux Racer běží na 2 fps.
Zkoušel jsem podle tohoto fóra http://ubuntuforums.org/showthread.php?t=615094 nainstalovat 3D ovladač, ale nepovedlo se mi to. Stáhnul jsem si ten 3D driver (myslím, že je pro ubuntu 7.04), rozbalil a přesunul jsem oba soubory do /usr/lib/xorg/modules/drivers/ a do xorg.conf jsem místo driver "vesa" napsal driver "sis".
Restartnul jsem X a spustilo se mi v low-graphics módu a napsalo to něco v tom smyslu, že to nemůže načíst modul SIS.
Můžete mi prosím poradit, abych mohl rozběhnout 3D akceleraci?
Děkuji
-
Ještě jsem zkusil nainstalovat sis ovladače pro linux, ale pravděpodobně nejsou na moji grafickou kartu.
SiS.com/download Download Center > IGP Graphics Drivers : SiS630 & SiS730 series : Linux
No, každopádně to zkončilo chybou:
bohous@notes:~/Plocha/drivers/sis$ ./XSiS_SVGA
_XSERVTransSocketUNIXCreateListener: ...SocketCreateListener() failed
_XSERVTransMakeAllCOTSServerListeners: server already running
Fatal server error:
Cannot establish any listening sockets - Make sure an X server isn't already running
When reporting a problem related to a server crash, please send
the full server output, not just the last messages
bohous@notes:~/Plocha/drivers/sis$