Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Internet a sítě => Téma založeno: funkymonk 26 Dubna 2009, 20:16:30
-
Ahoj,
Rozhodl jsem se prejit z Win XP na Ubuntu. Dnes jsem nainstaloval verzi 9.04, ale nejak nemuzu rozjet internet (na Win XP mi normalne fungoval). Pripojeni mam pres UPC, modem Webstar (Scientific Atlanta), sitovku Realtek. Zkousel jsem hledat na wiki v navodu na nastaveni internetu, ale je to tam udelany pro nejakou jinou verzi a ja se v tom moc nevyznam... Ani nevim, kde je vlastne problem, jestli vubec funguje sitova karta, nebo jestli nekde neco spatne nastavuju.
Prece jen Ubuntu jsem nainstaloval poprve dneska a vubec se v tom nevyznam. Kdyby mi nekdo poradil co s tim, budu Vam vdecnej.
Dekuju.
-
Klikni na >aplikacie >prislušenstvo >terminal a napíš tam :lspci a výpis pošli sem. Inač sieť by ti mala automaticky , cez network-managera nabehnuť, IP-čku si zistíš príkazom: ifconfig a branu : route -n ( to iste aj : ip -a , a ip -r )
-
zkus restartovat ten modem tím, že ho vytáhneš ze zásuvky cca na 30s.
-
matee: modem jsem restartovat zkousel a nic...
petertomasy:
jan@desktop:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 745 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 07)
00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 07)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:0a.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
00:0b.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax/Voice/Spkp (w/Handset) Modem (WorldW SmartDAA) (rev 01)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a4)
jan@desktop:~$ ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:276 (276.0 B) TX bytes:276 (276.0 B)
jan@desktop:~$ route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
-
není vidět síťová karta, dejte výpisy
lsmod
dmesg
-
mam tez pripojeni pres upc a naprosto bez problemu ale pri prechodu z vindous jsem funkcnost netu vyzkousel nejdriv na livecd
-
Diky za pomoc, vecer, az se dostanu k svemu PC, tak to sem hodim.
-
posilam vypisy z terminalu pro lsmod a dmesg:
jan@desktop:~$ lsmod
Module Size Used by
nls_iso8859_1 12032 0
nls_cp437 13696 0
vfat 18816 0
fat 58272 1 vfat
usb_storage 82880 0
binfmt_misc 16776 1
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
input_polldev 11912 0
video 25360 0
output 11008 1 video
lp 17156 0
ppdev 15620 0
snd_emu10k1_synth 14336 0
snd_emux_synth 40832 1 snd_emu10k1_synth
snd_seq_virmidi 13440 1 snd_emux_synth
snd_seq_midi_emul 14592 1 snd_emux_synth
snd_emu10k1 144288 4 snd_emu10k1_synth
snd_ac97_codec 112292 1 snd_emu10k1
ac97_bus 9856 1 snd_ac97_codec
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 82948 3 snd_emu10k1,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 16904 2 snd_emu10k1,snd_pcm
snd_util_mem 12288 2 snd_emux_synth,snd_emu10k1
snd_hwdep 15108 2 snd_emux_synth,snd_emu10k1
snd_seq_dummy 10756 0
snd_seq_oss 37760 0
snd_seq_midi 14336 0
snd_rawmidi 29696 3 snd_seq_virmidi,snd_emu10k1,snd_seq_midi
snd_seq_midi_event 15104 3 snd_seq_virmidi,snd_seq_oss,snd_seq_midi
snd_seq 56880 9 snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 29704 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 14988 8 snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 62628 19 snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_hwdep,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
psmouse 61972 0
pcspkr 10496 0
serio_raw 13316 0
soundcore 15200 1 snd
sis_agp 15360 1
parport_pc 40100 1
parport 42220 3 lp,ppdev,parport_pc
i2c_sis96x 12420 0
i2c_sis630 14348 0
shpchp 40212 0
agpgart 42696 1 sis_agp
8139too 32128 0
8139cp 27776 0
mii 13312 2 8139too,8139cp
floppy 64324 0
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
[ 0.000000] modified: 00000000ffee0000 - 00000000fff00000 (reserved)
[ 0.000000] modified: 00000000fffc0000 - 0000000100000000 (reserved)
[ 0.000000] kernel direct mapping tables up to 1fff0000 @ 10000-16000
[ 0.000000] RAMDISK: 1f8ae000 - 1ffdf5e9
[ 0.000000] ACPI: RSDP 000FA420, 0014 (r0 AMI )
[ 0.000000] ACPI: RSDT 1FFF0000, 002C (r1 AMIINT SiS735XX 1000 MSFT 100000B)
[ 0.000000] ACPI: FACP 1FFF0030, 0081 (r1 AMIINT SiS735XX 11 MSFT 100000B)
[ 0.000000] ACPI: DSDT 1FFF0110, 32F2 (r1 SiS 745 100 MSFT 100000D)
[ 0.000000] ACPI: FACS 1FFF8000, 0040
[ 0.000000] ACPI: APIC 1FFF00C0, 0050 (r1 AMIINT SiS735XX 1000 MSFT 100000B)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1fff0000
[ 0.000000] low ram: 00000000 - 1fff0000
[ 0.000000] bootmap 00012000 - 00016000
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 001fff0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 000087c52c] TEXT DATA BSS ==> [0000100000 - 000087c52c]
[ 0.000000] #4 [001f8ae000 - 001ffdf5e9] RAMDISK ==> [001f8ae000 - 001ffdf5e9]
[ 0.000000] #5 [000087d000 - 0000881000] INIT_PG_TABLE ==> [000087d000 - 0000881000]
[ 0.000000] #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
[ 0.000000] #7 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] #8 [0000012000 - 0000016000] BOOTMAP ==> [0000012000 - 0000016000]
[ 0.000000] found SMP MP-table at [c00fb980] 000fb980
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001fff0
[ 0.000000] HighMem 0x0001fff0 -> 0x0001fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0001fff0
[ 0.000000] On node 0 totalpages: 130943
[ 0.000000] free_area_init_node: node 0, pgdat c06d0f80, node_mem_map c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 125968 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 1, nr_node_ids 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129919
[ 0.000000] Kernel command line: root=UUID=dbad45e8-4e03-4bf8-a19f-828415402f13 ro quiet splash
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1500.094 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] allocated 2620800 bytes of page_cgroup
[ 0.004000] please try cgroup_disable=memory option if you don't want
[ 0.004000] Scanning for low memory corruption every 60 seconds
[ 0.004000] Memory: 501404k/524224k available (4126k kernel code, 22192k reserved, 2208k data, 532k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB)
[ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.004000] vmalloc : 0xe07f0000 - 0xff3fe000 ( 492 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 0.004000] .init : 0xc0737000 - 0xc07bc000 ( 532 kB)
[ 0.004000] .data : 0xc0507a6f - 0xc072fe60 (2208 kB)
[ 0.004000] .text : 0xc0100000 - 0xc0507a6f (4126 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.004020] Calibrating delay loop (skipped), value calculated using timer frequency.. 3000.18 BogoMIPS (lpj=6000376)
[ 0.004055] Security Framework initialized
[ 0.004068] SELinux: Disabled at boot.
[ 0.004114] AppArmor: AppArmor initialized
[ 0.004129] Mount-cache hash table entries: 512
[ 0.004373] Initializing cgroup subsys ns
[ 0.004380] Initializing cgroup subsys cpuacct
[ 0.004384] Initializing cgroup subsys memory
[ 0.004391] Initializing cgroup subsys freezer
[ 0.004412] CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
[ 0.004417] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004421] CPU: L2 Cache: 256K (64 bytes/line)
[ 0.004448] Checking 'hlt' instruction... OK.
[ 0.020667] SMP alternatives: switching to UP code
[ 0.225016] Freeing SMP alternatives: 18k freed
[ 0.225027] ACPI: Core revision 20080926
[ 0.229025] ACPI: Checking initramfs for custom DSDT
[ 0.618263] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.657958] CPU0: AMD Athlon(tm) XP 1800+ stepping 01
[ 0.660002] Brought up 1 CPUs
[ 0.660002] Total of 1 processors activated (3000.18 BogoMIPS).
[ 0.660002] CPU0 attaching NULL sched-domain.
[ 0.660002] net_namespace: 776 bytes
[ 0.660002] Booting paravirtualized kernel on bare hardware
[ 0.660002] Time: 16:59:45 Date: 04/27/09
[ 0.660002] regulator: core version 0.5
[ 0.660002] NET: Registered protocol family 16
[ 0.660002] EISA bus registered
[ 0.660002] ACPI: bus type pci registered
[ 0.660002] PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
[ 0.660002] PCI: Using configuration type 1 for base access
[ 0.661747] ACPI: EC: Look up EC in DSDT
[ 0.668636] ACPI: Interpreter enabled
[ 0.668645] ACPI: (supports S0 S1 S4 S5)
[ 0.668670] ACPI: Using IOAPIC for interrupt routing
[ 0.674915] ACPI: No dock devices found.
[ 0.674932] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.675009] pci 0000:00:00.0: reg 10 32bit mmio: [0xd0000000-0xd3ffffff]
[ 0.675143] pci 0000:00:02.0: Enabling SiS 96x SMBus
[ 0.675189] pci 0000:00:02.1: reg 20 io port: [0xc00-0xc1f]
[ 0.675223] pci 0000:00:02.2: reg 10 32bit mmio: [0xcfffe000-0xcfffefff]
[ 0.675274] pci 0000:00:02.3: reg 10 32bit mmio: [0xcffff000-0xcfffffff]
[ 0.675348] pci 0000:00:02.5: reg 20 io port: [0xff00-0xff0f]
[ 0.675406] pci 0000:00:0a.0: reg 10 io port: [0xdc00-0xdc3f]
[ 0.675444] pci 0000:00:0a.0: supports D1 D2
[ 0.675477] pci 0000:00:0b.0: reg 10 32bit mmio: [0xcff90000-0xcff9ffff]
[ 0.675485] pci 0000:00:0b.0: reg 14 io port: [0xd800-0xd807]
[ 0.675517] pci 0000:00:0b.0: supports D1 D2
[ 0.675521] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.675527] pci 0000:00:0b.0: PME# disabled
[ 0.675561] pci 0000:00:0c.0: reg 10 io port: [0xd400-0xd4ff]
[ 0.675569] pci 0000:00:0c.0: reg 14 32bit mmio: [0xcfffdf00-0xcfffdfff]
[ 0.675596] pci 0000:00:0c.0: reg 30 32bit mmio: [0xcffe0000-0xcffeffff]
[ 0.675606] pci 0000:00:0c.0: supports D1 D2
[ 0.675609] pci 0000:00:0c.0: PME# supported from D1 D2 D3hot D3cold
[ 0.675614] pci 0000:00:0c.0: PME# disabled
[ 0.675683] pci 0000:01:00.0: reg 10 32bit mmio: [0xce000000-0xceffffff]
[ 0.675691] pci 0000:01:00.0: reg 14 32bit mmio: [0xc0000000-0xc7ffffff]
[ 0.675715] pci 0000:01:00.0: reg 30 32bit mmio: [0xcfee0000-0xcfefffff]
[ 0.675769] pci 0000:00:01.0: bridge 32bit mmio: [0xcdd00000-0xcfefffff]
[ 0.675776] pci 0000:00:01.0: bridge 32bit mmio pref: [0xbda00000-0xcdbfffff]
[ 0.675786] bus 00 -> node 0
[ 0.675795] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.677304] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 0.677493] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 0.677670] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 0.677846] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 0.678021] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.678197] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.678373] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.678548] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 0.678672] ACPI: Power Resource [URP1] (off)
[ 0.678725] ACPI: Power Resource [URP2] (off)
[ 0.678772] ACPI: Power Resource [FDDP] (off)
[ 0.678817] ACPI: Power Resource [LPTP] (off)
[ 0.678939] ACPI: WMI: Mapper loaded
[ 0.679361] SCSI subsystem initialized
[ 0.679451] libata version 3.00 loaded.
[ 0.679544] usbcore: registered new interface driver usbfs
[ 0.679575] usbcore: registered new interface driver hub
[ 0.679627] usbcore: registered new device driver usb
[ 0.679834] PCI: Using ACPI for IRQ routing
[ 0.680025] Bluetooth: Core ver 2.13
[ 0.680112] NET: Registered protocol family 31
[ 0.680115] Bluetooth: HCI device and connection manager initialized
[ 0.680121] Bluetooth: HCI socket layer initialized
[ 0.680125] NET: Registered protocol family 8
[ 0.680128] NET: Registered protocol family 20
[ 0.680145] NetLabel: Initializing
[ 0.680147] NetLabel: domain hash size = 128
[ 0.680150] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.680181] NetLabel: unlabeled traffic allowed by default
[ 0.680353] AppArmor: AppArmor Filesystem Enabled
[ 0.680367] pnp: PnP ACPI init
[ 0.680367] ACPI: bus type pnp registered
[ 0.686019] pnp: PnP ACPI: found 13 devices
[ 0.686023] ACPI: ACPI bus type pnp unregistered
[ 0.686030] PnPBIOS: Disabled by ACPI PNP
[ 0.720847] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.720850] pci 0000:00:01.0: IO window: disabled
[ 0.720859] pci 0000:00:01.0: MEM window: 0xcdd00000-0xcfefffff
[ 0.720864] pci 0000:00:01.0: PREFETCH window: 0x000000bda00000-0x000000cdbfffff
[ 0.720887] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.720890] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.720893] bus: 01 index 0 mmio: [0x0-0x0]
[ 0.720896] bus: 01 index 1 mmio: [0xcdd00000-0xcfefffff]
[ 0.720899] bus: 01 index 2 mmio: [0xbda00000-0xcdbfffff]
[ 0.720902] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.720925] NET: Registered protocol family 2
[ 0.721127] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.721541] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.721873] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.722217] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.722221] TCP reno registered
[ 0.722448] NET: Registered protocol family 1
[ 0.722703] checking if image is initramfs... it is
[ 1.224048] Switched to high resolution mode on CPU 0
[ 1.599695] Freeing initrd memory: 7365k freed
[ 1.599920] cpufreq: No nForce2 chipset.
[ 1.600201] audit: initializing netlink socket (disabled)
[ 1.600241] type=2000 audit(1240851585.600:1): initialized
[ 1.610707] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.612598] VFS: Disk quotas dquot_6.5.1
[ 1.612694] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.613624] fuse init (API version 7.10)
[ 1.613735] msgmni has been set to 994
[ 1.614096] alg: No test for stdrng (krng)
[ 1.614118] io scheduler noop registered
[ 1.614122] io scheduler anticipatory registered
[ 1.614125] io scheduler deadline registered
[ 1.614148] io scheduler cfq registered (default)
[ 1.614264] pci 0000:01:00.0: Boot video device
[ 1.619054] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.619068] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.619290] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.619295] ACPI: Power Button (FF) [PWRF]
[ 1.619374] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.619378] ACPI: Power Button (CM) [PWRB]
[ 1.619592] processor ACPI_CPU:00: registered as cooling_device0
[ 1.622232] isapnp: Scanning for PnP cards...
[ 1.975538] isapnp: No Plug & Play device found
[ 1.977648] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.977765] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.977862] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.978231] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.978372] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.979571] brd: module loaded
[ 1.980124] loop: module loaded
[ 1.980272] Fixed MDIO Bus: probed
[ 1.980283] PPP generic driver version 2.4.2
[ 1.980394] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.980453] Driver 'sd' needs updating - please use bus_type methods
[ 1.980476] Driver 'sr' needs updating - please use bus_type methods
[ 1.981266] pata_sis 0000:00:02.5: version 0.5.2
[ 1.981649] scsi0 : pata_sis
[ 1.981844] scsi1 : pata_sis
[ 1.983150] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 1.983155] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 2.200571] ata1.00: ATA-6: ST3120022A, 3.06, max UDMA/100
[ 2.200575] ata1.00: 234441648 sectors, multi 16: LBA48
[ 2.216378] ata1.00: configured for UDMA/100
[ 2.388360] ata2.00: ATAPI: LITE-ON DVDRW SOHW-1653S, CS02, max UDMA/66
[ 2.388399] ata2.01: ATAPI: CD-W540E, 1.0D, max UDMA/33
[ 2.388423] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 2.404253] ata2.00: configured for UDMA/33
[ 2.420279] ata2.01: configured for UDMA/33
[ 2.421089] scsi 0:0:0:0: Direct-Access ATA ST3120022A 3.06 PQ: 0 ANSI: 5
[ 2.421262] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 2.421294] sd 0:0:0:0: [sda] Write Protect is off
[ 2.421298] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.421343] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.421475] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 2.421500] sd 0:0:0:0: [sda] Write Protect is off
[ 2.421503] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.421544] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.421551] sda: sda1 sda2 < sda5 >
[ 2.455736] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.455836] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.456640] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW SOHW-1653S CS02 PQ: 0 ANSI: 5
[ 2.460539] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 2.460545] Uniform CD-ROM driver Revision: 3.20
[ 2.460712] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.460788] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.462429] scsi 1:0:1:0: CD-ROM TEAC CD-W540E 1.0D PQ: 0 ANSI: 5
[ 2.464799] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 2.464900] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 2.464953] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 2.465182] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.465209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.465254] ohci_hcd 0000:00:02.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.465309] ohci_hcd 0000:00:02.2: OHCI Host Controller
[ 2.465426] ohci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 2.465482] ohci_hcd 0000:00:02.2: irq 19, io mem 0xcfffe000
[ 2.522115] usb usb1: configuration #1 chosen from 1 choice
[ 2.522159] hub 1-0:1.0: USB hub found
[ 2.522182] hub 1-0:1.0: 3 ports detected
[ 2.522341] ohci_hcd 0000:00:02.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.522357] ohci_hcd 0000:00:02.3: OHCI Host Controller
[ 2.522429] ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2
[ 2.522458] ohci_hcd 0000:00:02.3: irq 23, io mem 0xcffff000
[ 2.578067] usb usb2: configuration #1 chosen from 1 choice
[ 2.578114] hub 2-0:1.0: USB hub found
[ 2.578132] hub 2-0:1.0: 3 ports detected
[ 2.578249] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.578396] usbcore: registered new interface driver libusual
[ 2.578452] usbcore: registered new interface driver usbserial
[ 2.578469] USB Serial support registered for generic
[ 2.578510] usbcore: registered new interface driver usbserial_generic
[ 2.578513] usbserial: USB Serial Driver core
[ 2.578588] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 2.578892] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.578903] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.579076] mice: PS/2 mouse device common for all mice
[ 2.579260] rtc_cmos 00:02: RTC can wake from S4
[ 2.579318] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.579346] rtc0: alarms up to one month, 114 bytes nvram
[ 2.579445] device-mapper: uevent: version 1.0.3
[ 2.579646] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 2.579746] device-mapper: multipath: version 1.0.5 loaded
[ 2.579752] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.579900] EISA: Probing bus 0 at eisa.0
[ 2.579942] EISA: Detected 0 cards.
[ 2.579996] cpuidle: using governor ladder
[ 2.580029] cpuidle: using governor menu
[ 2.580813] TCP cubic registered
[ 2.580939] NET: Registered protocol family 10
[ 2.581555] lo: Disabled Privacy Extensions
[ 2.582022] NET: Registered protocol family 17
[ 2.582053] Bluetooth: L2CAP ver 2.11
[ 2.582055] Bluetooth: L2CAP socket layer initialized
[ 2.582060] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.582063] Bluetooth: SCO socket layer initialized
[ 2.582127] Bluetooth: RFCOMM socket layer initialized
[ 2.582142] Bluetooth: RFCOMM TTY layer initialized
[ 2.582145] Bluetooth: RFCOMM ver 1.10
[ 2.582178] powernow-k8: Processor cpuid 681 not supported
[ 2.582226] Using IPI No-Shortcut mode
[ 2.582409] registered taskstats version 1
[ 2.582550] Magic number: 5:157:996
[ 2.582720] rtc_cmos 00:02: setting system clock to 2009-04-27 16:59:47 UTC (1240851587)
[ 2.582725] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.582727] EDD information not available.
[ 2.584160] Freeing unused kernel memory: 532k freed
[ 2.584342] Write protecting the kernel text: 4128k
[ 2.584399] Write protecting the kernel read-only data: 1532k
[ 2.623398] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.908054] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 3.088117] usb 1-1: device descriptor read/64, error -62
[ 3.227261] Floppy drive(s): fd0 is 1.44M
[ 3.247911] FDC 0 is a post-1991 82077
[ 3.376088] usb 1-1: device descriptor read/64, error -62
[ 3.420129] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 3.420201] 8139cp 0000:00:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 3.432909] 8139too Fast Ethernet driver 0.9.28
[ 3.433014] 8139too 0000:00:0c.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.434227] eth0: RealTek RTL8139 at 0xd400, 00:00:00:00:00:00, IRQ 19
[ 3.434231] eth0: Identified 8139 chip type 'RTL-8100'
[ 3.656131] usb 1-1: new full speed USB device using ohci_hcd and address 3
[ 3.836144] usb 1-1: device descriptor read/64, error -62
[ 4.120066] usb 1-1: device descriptor read/64, error -62
[ 4.172239] PM: Starting manual resume from disk
[ 4.172248] PM: Resume from partition 8:5
[ 4.172251] PM: Checking hibernation image.
[ 4.172581] PM: Resume from disk failed.
[ 4.223164] kjournald starting. Commit interval 5 seconds
[ 4.223191] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.400049] usb 1-1: new full speed USB device using ohci_hcd and address 4
[ 4.808047] usb 1-1: device not accepting address 4, error -62
[ 4.984049] usb 1-1: new full speed USB device using ohci_hcd and address 5
[ 5.392033] usb 1-1: device not accepting address 5, error -62
[ 5.392079] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 5.568048] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 5.777633] usb 2-1: configuration #1 chosen from 1 choice
[ 5.780456] hub 2-1:1.0: USB hub found
[ 5.783410] hub 2-1:1.0: 4 ports detected
[ 9.187328] udev: starting version 141
[ 9.464019] Linux agpgart interface v0.103
[ 9.477092] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.487728] sis630_smbus 0000:00:02.0: SIS630 comp. bus not detected, module not inserted.
[ 9.503665] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[ 9.503678] ACPI: I/O resource 0000:00:02.1 [0xc00-0xc1f] conflicts with ACPI region SMRG [0xc00-0xc1f]
[ 9.503682] ACPI: Device needs an ACPI driver
[ 9.552125] parport_pc 00:0a: reported by Plug and Play ACPI
[ 9.552238] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 9.566241] agpgart-sis 0000:00:00.0: SiS chipset [1039/0745]
[ 9.572586] agpgart-sis 0000:00:00.0: AGP aperture is 64M @ 0xd0000000
[ 9.831552] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 10.071839] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 10.417830] EMU10K1_Audigy 0000:00:0a.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 10.420433] Audigy2 value: Special config.
[ 10.528099] psmouse serio1: ID: 10 00 64<6>ppdev: user-space parallel port driver
[ 11.034571] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 11.185284] lp0: using parport0 (interrupt-driven).
[ 11.359976] Adding 1485972k swap on /dev/sda5. Priority:-1 extents:1 across:1485972k
[ 11.943496] EXT3 FS on sda1, internal journal
[ 13.357224] type=1505 audit(1240851598.273:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1838
[ 13.454259] type=1505 audit(1240851598.369:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1842
[ 13.454752] type=1505 audit(1240851598.369:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1842
[ 13.454900] type=1505 audit(1240851598.369:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1842
[ 13.455029] type=1505 audit(1240851598.369:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1842
[ 13.728096] type=1505 audit(1240851598.645:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1847
[ 13.728734] type=1505 audit(1240851598.645:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1847
[ 13.789453] type=1505 audit(1240851598.705:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1851
[ 17.372468] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.372475] Bluetooth: BNEP filters: protocol multicast
[ 17.431072] Bridge firewalling registered
[ 17.620024] usb 1-1: new full speed USB device using ohci_hcd and address 6
[ 17.800034] usb 1-1: device descriptor read/64, error -62
[ 18.088053] usb 1-1: device descriptor read/64, error -62
[ 18.368803] usb 1-1: new full speed USB device using ohci_hcd and address 7
[ 18.548028] usb 1-1: device descriptor read/64, error -62
[ 18.837505] usb 1-1: device descriptor read/64, error -62
[ 19.104060] usb 1-1: new full speed USB device using ohci_hcd and address 8
[ 19.524026] usb 1-1: device not accepting address 8, error -62
[ 19.700151] usb 1-1: new full speed USB device using ohci_hcd and address 9
[ 20.109246] usb 1-1: device not accepting address 9, error -62
[ 20.109293] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 738.793985] usb 2-1.2: new full speed USB device using ohci_hcd and address 3
[ 738.946423] usb 2-1.2: configuration #1 chosen from 1 choice
[ 739.003996] Initializing USB Mass Storage driver...
[ 739.007206] scsi2 : SCSI emulation for USB Mass Storage devices
[ 739.007756] usbcore: registered new interface driver usb-storage
[ 739.007764] USB Mass Storage support registered.
[ 739.010823] usb-storage: device found at 3
[ 739.010829] usb-storage: waiting for device to settle before scanning
[ 744.010081] usb-storage: device scan complete
[ 744.017037] scsi 2:0:0:0: Direct-Access Kingston DataTraveler II+ PMAP PQ: 0 ANSI: 0 CCS
[ 744.489950] sd 2:0:0:0: [sdb] 2030592 512-byte hardware sectors: (1.03 GB/991 MiB)
[ 744.496972] sd 2:0:0:0: [sdb] Write Protect is off
[ 744.496982] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 744.496987] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 744.522904] sd 2:0:0:0: [sdb] 2030592 512-byte hardware sectors: (1.03 GB/991 MiB)
[ 744.529943] sd 2:0:0:0: [sdb] Write Protect is off
[ 744.529954] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 744.529958] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 744.529972] sdb: sdb1
[ 744.540691] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 744.540872] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 895.366547] usb 2-1.2: USB disconnect, address 3
[ 1174.746009] usb 2-1.2: new full speed USB device using ohci_hcd and address 4
[ 1174.898474] usb 2-1.2: configuration #1 chosen from 1 choice
[ 1174.944894] scsi3 : SCSI emulation for USB Mass Storage devices
[ 1174.948857] usb-storage: device found at 4
[ 1174.948864] usb-storage: waiting for device to settle before scanning
[ 1179.950092] usb-storage: device scan complete
[ 1179.957049] scsi 3:0:0:0: Direct-Access Kingston DataTraveler II+ PMAP PQ: 0 ANSI: 0 CCS
[ 1180.383929] sd 3:0:0:0: [sdb] 2030592 512-byte hardware sectors: (1.03 GB/991 MiB)
[ 1180.390944] sd 3:0:0:0: [sdb] Write Protect is off
[ 1180.390954] sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1180.390959] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1180.416929] sd 3:0:0:0: [sdb] 2030592 512-byte hardware sectors: (1.03 GB/991 MiB)
[ 1180.423927] sd 3:0:0:0: [sdb] Write Protect is off
[ 1180.423936] sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1180.423940] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1180.423955] sdb: sdb1
[ 1180.439577] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 1180.439732] sd 3:0:0:0: Attached scsi generic sg3 type 0
jan@desktop:~$
-
Ovladač je načtený, ale nelíbí se mi ta mac adresa
[ 3.434227] eth0: RealTek RTL8139 at 0xd400, 00:00:00:00:00:00, IRQ 19
gksudo gedit /etc/network/interfacesdoplňte tam pokud není:
auto eth0
iface eth0 inet dhcp
hwaddress ether 00:0c:76:b3:df:bauložte a
sudo /etc/init.d/networking restart
ip a
pokud tam stále nebude IP adresa pro eth0
sudo ip l s eth0 up
sudo dhclient eth0
ip a
pokud stále není adresa
sudo mii-tool
sudo ethtool eth0
případné výpisy a obsah /etc/network/interfaces sem.
-
na tu mac adresu pozor - u UPC se nova mac adresa musi "preregistrovat", jinak nepojede net
-
me to prijde nejake divne ja jsem instaloval kubuntu trem kamaradum a sobe vsichni mame upc a chodi naprosto v pohode a to i bez restartu modemu
-
na tu mac adresu pozor - u UPC se nova mac adresa musi "preregistrovat", jinak nepojede net
To už delší dobu neplatí, registrace MAC síťové karty a následné čachry s případným připojením routeru, klonováním MAC atd. už nejsou potřeba. Při změně připojeného zařízení ke kabelovému modemu stačí tento pouze restartovat.
-
na tu mac adresu pozor - u UPC se nova mac adresa musi "preregistrovat", jinak nepojede net
To už delší dobu neplatí, registrace MAC síťové karty a následné čachry s případným připojením routeru, klonováním MAC atd. už nejsou potřeba. Při změně připojeného zařízení ke kabelovému modemu stačí tento pouze restartovat.
fakt? tak tim lip :)
sorry za mylnou informaci - vychazel jsem z vlastni zkusenosti, ktera je bohudik starsiho data :)
-
Uf! Tak vypada to, ze uz to funguje. Jenom teda v tom network connections nemam nic. Ale internet normalne bezi.
v /etc/network/interfacesbylo jen auto lo
iface lo inet loopbacktak jsem to doplnil podle navodu a dal sudo /etc/init.d/networking restart
Pak jsem uz jen restartoval PC a modem a vse ok.
Dekuju vsem za pomoc a za ochotu!