Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Obecná podpora => Téma založeno: Peter33 03 Července 2010, 14:29:38
-
Zdravim
Systém se mi z ničeho nic (myslim bez nějakých úprav či aktualizací) začal zamrzat, zkrátka je s nim skoro nemožná práce. OVšem správce procesů neukazoval nějaký zvlášť zatěžující proces, tak jsem začal podezřívat disk, ovšem SMART test i test povrchu dopadl v pořádku. Ale.... :
dmesg:
(...)
0.324665] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.327683] VFS: Disk quotas dquot_6.5.2
[ 0.327807] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.328930] fuse init (API version 7.13)
[ 0.329083] msgmni has been set to 978
[ 0.332438] alg: No test for stdrng (krng)
[ 0.332571] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.332578] io scheduler noop registered
[ 0.332582] io scheduler anticipatory registered
[ 0.332585] io scheduler deadline registered
[ 0.332673] io scheduler cfq registered (default)
[ 0.332904] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.332958] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.333171] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.333180] ACPI: Power Button [PWRB]
[ 0.333295] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.333301] ACPI: Power Button [PWRF]
[ 0.333393] fan PNP0C0B:00: registered as cooling_device0
[ 0.333403] ACPI: Fan [FAN] (on)
[ 0.334042] processor LNXCPU:00: registered as cooling_device1
[ 0.349579] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.349599] ACPI: Thermal Zone [THRM] (59 C)
[ 0.352092] isapnp: Scanning for PnP cards...
[ 0.360590] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.360746] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.360894] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.361415] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.361607] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.363664] brd: module loaded
[ 0.368963] loop: module loaded
[ 0.369210] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.369646] pata_acpi 0000:00:09.0: setting latency timer to 64
[ 0.370276] Fixed MDIO Bus: probed
[ 0.370347] PPP generic driver version 2.4.2
[ 0.370440] tun: Universal TUN/TAP device driver, 1.6
[ 0.370445] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.370604] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.371200] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 0.371213] alloc irq_desc for 22 on node -1
[ 0.371217] alloc kstat_irqs on node -1
[ 0.371233] ehci_hcd 0000:00:02.2: PCI INT C -> Link[APCL] -> GSI 22 (level, high) -> IRQ 22
[ 0.371267] ehci_hcd 0000:00:02.2: setting latency timer to 64
[ 0.371273] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 0.371358] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 0.371412] ehci_hcd 0000:00:02.2: debug port 1
[ 0.371420] ehci_hcd 0000:00:02.2: selective suspend/wakeup unavailable
[ 0.371429] ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
[ 0.371462] ehci_hcd 0000:00:02.2: irq 22, io mem 0xef005000
[ 0.420068] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
[ 0.420399] usb usb1: configuration #1 chosen from 1 choice
[ 0.420464] hub 1-0:1.0: USB hub found
[ 0.420490] hub 1-0:1.0: 6 ports detected
[ 0.420638] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.421254] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[ 0.421266] alloc irq_desc for 21 on node -1
[ 0.421271] alloc kstat_irqs on node -1
[ 0.421285] ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 21 (level, high) -> IRQ 21
[ 0.421320] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 0.421326] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 0.421416] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 0.421470] ohci_hcd 0000:00:02.0: irq 21, io mem 0xef003000
[ 0.506228] usb usb2: configuration #1 chosen from 1 choice
[ 0.506291] hub 2-0:1.0: USB hub found
[ 0.506317] hub 2-0:1.0: 3 ports detected
[ 0.506982] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
[ 0.506994] alloc irq_desc for 20 on node -1
[ 0.506999] alloc kstat_irqs on node -1
[ 0.507014] ohci_hcd 0000:00:02.1: PCI INT B -> Link[APCG] -> GSI 20 (level, high) -> IRQ 20
[ 0.507049] ohci_hcd 0000:00:02.1: setting latency timer to 64
[ 0.507055] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 0.507143] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[ 0.507199] ohci_hcd 0000:00:02.1: irq 20, io mem 0xef004000
[ 0.593847] usb usb3: configuration #1 chosen from 1 choice
[ 0.593911] hub 3-0:1.0: USB hub found
[ 0.593938] hub 3-0:1.0: 3 ports detected
[ 0.594063] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.594250] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.594255] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.595014] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.600728] mice: PS/2 mouse device common for all mice
[ 0.601025] rtc_cmos 00:06: RTC can wake from S4
[ 0.601130] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 0.601184] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 0.601378] device-mapper: uevent: version 1.0.3
[ 0.601632] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.601746] device-mapper: multipath: version 1.1.0 loaded
[ 0.601751] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.604186] EISA: Probing bus 0 at eisa.0
[ 0.604217] Cannot allocate resource for EISA slot 4
[ 0.604222] Cannot allocate resource for EISA slot 5
[ 0.604242] EISA: Detected 0 cards.
[ 0.605224] cpuidle: using governor ladder
[ 0.605230] cpuidle: using governor menu
[ 0.606065] TCP cubic registered
[ 0.606394] NET: Registered protocol family 10
[ 0.607204] lo: Disabled Privacy Extensions
[ 0.607750] NET: Registered protocol family 17
[ 0.607837] powernow-k8: Processor cpuid 662 not supported
[ 0.607874] Using IPI No-Shortcut mode
[ 0.609467] PM: Resume from disk failed.
[ 0.609511] registered taskstats version 1
[ 0.609872] Magic number: 2:837:983
[ 0.610063] rtc_cmos 00:06: setting system clock to 2010-07-03 11:59:24 UTC (1278158364)
[ 0.610069] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.610073] EDD information not available.
[ 0.624733] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.035807] isapnp: No Plug & Play device found
[ 1.078503] Freeing initrd memory: 7778k freed
[ 1.092999] usb 2-3: new low speed USB device using ohci_hcd and address 2
[ 1.093105] Freeing unused kernel memory: 656k freed
[ 1.094501] Write protecting the kernel text: 4676k
[ 1.094557] Write protecting the kernel read-only data: 1840k
[ 1.140571] udev: starting version 151
[ 1.310373] usb 2-3: configuration #1 chosen from 1 choice
[ 1.508390] Floppy drive(s): fd0 is 1.44M
[ 1.531224] FDC 0 is a post-1991 82077
[ 1.580629] pata_amd 0000:00:09.0: version 0.4.1
[ 1.580753] pata_amd 0000:00:09.0: setting latency timer to 64
[ 1.592669] scsi0 : pata_amd
[ 1.593128] scsi1 : pata_amd
[ 1.594528] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 1.594535] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.595025] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 1.595518] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
[ 1.595530] forcedeth 0000:00:04.0: PCI INT A -> Link[APCH] -> GSI 22 (level, high) -> IRQ 22
[ 1.595541] forcedeth 0000:00:04.0: setting latency timer to 64
[ 1.595651] nv_probe: set workaround bit for reversed mac addr
[ 1.760537] ata1.00: ATA-6: WDC WD400BB-00JHA0, 05.01C05, max UDMA/100
[ 1.760544] ata1.00: 78165360 sectors, multi 16: LBA
[ 1.760590] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1.768475] ata1.00: configured for UDMA/100
[ 1.768717] scsi 0:0:0:0: Direct-Access ATA WDC WD400BB-00JH 05.0 PQ: 0 ANSI: 5
[ 1.769071] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.769741] sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 1.769845] sd 0:0:0:0: [sda] Write Protect is off
[ 1.769851] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.769905] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.770211] sda:
[ 1.774069] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 1.774074] ata1.00: BMDMA stat 0x64
[ 1.774081] ata1.00: failed command: READ DMA
[ 1.774093] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 1.774096] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 1.774101] ata1.00: status: { DRDY ERR }
[ 1.774105] ata1.00: error: { ICRC ABRT }
[ 1.774142] ata1: soft resetting link
[ 1.940558] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1.948447] ata1.00: configured for UDMA/100
[ 1.948462] ata1: EH complete
[ 1.956935] ata1.00: limiting speed to UDMA/66:PIO4
[ 1.956941] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 1.956946] ata1.00: BMDMA stat 0x64
[ 1.956950] ata1.00: failed command: READ DMA
[ 1.956961] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 1.956964] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 1.956969] ata1.00: status: { DRDY ERR }
[ 1.956973] ata1.00: error: { ICRC ABRT }
[ 1.957001] ata1: soft resetting link
[ 2.113313] forcedeth 0000:00:04.0: ifname eth0, PHY OUI 0x57d @ 1, addr 00:10:dc:da:78:1c
[ 2.113320] forcedeth 0000:00:04.0: timirq lnktim desc-v1
[ 2.120586] ata1: nv_mode_filter: 0x1f39f&0x3f39f->0x1f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 2.136446] ata1.00: configured for UDMA/66
[ 2.136476] ata1: EH complete
[ 2.139859] sda1 sda2 < sda5 sda6 >
[ 2.168266] sda: detected capacity change from 0 to 40020664320
[ 2.169137] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.185371] usbcore: registered new interface driver hiddev
[ 2.192285] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:02.0/usb2/2-3/2-3:1.0/input/input4
[ 2.192758] generic-usb 0003:045E:0040.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-3/input0
[ 2.192838] usbcore: registered new interface driver usbhid
[ 2.193097] usbhid: v2.6:USB HID core driver
[ 2.639307] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 2.639317] EXT3-fs: write access will be enabled during recovery.
[ 2.692446] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 2.692451] ata1.00: BMDMA stat 0x64
[ 2.692459] ata1.00: failed command: READ DMA
[ 2.692472] ata1.00: cmd c8/00:00:17:1b:cc/00:00:00:00:00/e0 tag 0 dma 131072 in
[ 2.692474] res 51/84:00:16:1c:cc/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 2.692480] ata1.00: status: { DRDY ERR }
[ 2.692484] ata1.00: error: { ICRC ABRT }
[ 2.692527] ata1: soft resetting link
[ 2.856567] ata1: nv_mode_filter: 0x1f39f&0x3f39f->0x1f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 2.864457] ata1.00: configured for UDMA/66
[ 2.864474] ata1: EH complete
[ 2.875073] ata1.00: limiting speed to UDMA/33:PIO4
[ 2.875081] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 2.875085] ata1.00: BMDMA stat 0x64
[ 2.875090] ata1.00: failed command: READ DMA
[ 2.875101] ata1.00: cmd c8/00:00:17:1b:cc/00:00:00:00:00/e0 tag 0 dma 131072 in
[ 2.875104] res 51/84:00:16:1c:cc/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 2.875109] ata1.00: status: { DRDY ERR }
[ 2.875113] ata1.00: error: { ICRC ABRT }
[ 2.875140] ata1: soft resetting link
[ 3.036545] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 3.044453] ata1.00: configured for UDMA/33
[ 3.044464] ata1: EH complete
[ 3.210156] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 3.210163] ata1.00: BMDMA stat 0x64
[ 3.210171] ata1.00: failed command: WRITE DMA
[ 3.210183] ata1.00: cmd ca/00:08:ff:ea:57/00:00:00:00:00/e0 tag 0 dma 4096 out
[ 3.210186] res 51/84:01:06:eb:57/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 3.210191] ata1.00: status: { DRDY ERR }
[ 3.210196] ata1.00: error: { ICRC ABRT }
[ 3.210237] ata1: soft resetting link
[ 3.484554] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 3.492442] ata1.00: configured for UDMA/33
[ 3.492457] ata1: EH complete
[ 3.496909] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 3.496914] ata1.00: BMDMA stat 0x64
[ 3.496919] ata1.00: failed command: WRITE DMA
[ 3.496930] ata1.00: cmd ca/00:18:5f:1a:6c/00:00:00:00:00/e0 tag 0 dma 12288 out
[ 3.496933] res 51/84:01:76:1a:6c/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 3.496938] ata1.00: status: { DRDY ERR }
[ 3.496942] ata1.00: error: { ICRC ABRT }
[ 3.496971] ata1: soft resetting link
[ 3.660531] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 3.668456] ata1.00: configured for UDMA/33
[ 3.668466] ata1: EH complete
[ 3.669014] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 3.669019] ata1.00: BMDMA stat 0x64
[ 3.669024] ata1.00: failed command: WRITE DMA
[ 3.669035] ata1.00: cmd ca/00:18:5f:1a:6c/00:00:00:00:00/e0 tag 0 dma 12288 out
[ 3.669038] res 51/84:01:76:1a:6c/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 3.669043] ata1.00: status: { DRDY ERR }
[ 3.669047] ata1.00: error: { ICRC ABRT }
[ 3.669075] ata1: soft resetting link
[ 3.832547] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 3.840456] ata1.00: configured for UDMA/33
[ 3.840466] ata1: EH complete
[ 3.841018] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 3.841023] ata1.00: BMDMA stat 0x64
[ 3.841028] ata1.00: failed command: WRITE DMA
[ 3.841039] ata1.00: cmd ca/00:18:5f:1a:6c/00:00:00:00:00/e0 tag 0 dma 12288 out
[ 3.841041] res 51/84:01:76:1a:6c/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 3.841047] ata1.00: status: { DRDY ERR }
[ 3.841051] ata1.00: error: { ICRC ABRT }
[ 3.841078] ata1: soft resetting link
[ 4.004547] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 4.012464] ata1.00: configured for UDMA/33
[ 4.012473] ata1: EH complete
[ 4.020790] kjournald starting. Commit interval 5 seconds
[ 4.020827] EXT3-fs: sda1: orphan cleanup on readonly fs
[ 4.020840] ext3_orphan_cleanup: deleting unreferenced inode 156609
[ 4.020908] ext3_orphan_cleanup: deleting unreferenced inode 156597
[ 4.020922] EXT3-fs: sda1: 2 orphan inodes deleted
[ 4.020925] EXT3-fs: recovery complete.
[ 4.024121] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.789049] Adding 2931820k swap on /dev/sda6. Priority:-1 extents:1 across:2931820k
[ 13.197100] udev: starting version 151
[ 13.586979] i2c i2c-0: nForce2 SMBus adapter at 0x5000
[ 13.587031] i2c i2c-1: nForce2 SMBus adapter at 0x5040
[ 13.792501] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.794841] Linux agpgart interface v0.103
[ 14.001693] type=1505 audit(1278158377.889:2): operation="profile_load" pid=400 name="/sbin/dhclient3"
[ 14.002199] type=1505 audit(1278158377.889:3): operation="profile_load" pid=400 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.002477] type=1505 audit(1278158377.889:4): operation="profile_load" pid=400 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.068669] agpgart: Detected NVIDIA nForce2 chipset
[ 14.076140] parport_pc 00:0c: reported by Plug and Play ACPI
[ 14.076211] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 14.130714] lp: driver loaded but no devices found
[ 14.164527] lp0: using parport0 (interrupt-driven).
[ 14.200921] agpgart-nvidia 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[ 14.245224] Disabling lock debugging due to kernel taint
[ 14.290523] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
[ 14.541044] vga16fb: initializing
[ 14.541059] vga16fb: mapped to 0xc00a0000
[ 14.541550] fb0: VGA16 VGA frame buffer device
[ 14.545408] ppdev: user-space parallel port driver
[ 15.239464] ndiswrapper: driver tnet1130 (Texas Instruments,03/10/2004,6.0.0.18) loaded
[ 15.240426] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 15.240440] alloc irq_desc for 17 on node -1
[ 15.240444] alloc kstat_irqs on node -1
[ 15.240461] ndiswrapper 0000:01:08.0: PCI INT A -> Link[APC2] -> GSI 17 (level, high) -> IRQ 17
[ 17.183194] ndiswrapper: using IRQ 17
[ 17.486892] wlan0: ethernet device 00:4f:62:00:9c:11 using NDIS driver: tnet1130, version: 0x5000200, NDIS version: 0x501, vendor: 'TNET1130', 104C:9066.5.conf
[ 17.487096] wlan0: encryption modes supported: WEP; TKIP with WPA
[ 17.491696] usbcore: registered new interface driver ndiswrapper
[ 17.531123] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 17.531138] alloc irq_desc for 19 on node -1
[ 17.531143] alloc kstat_irqs on node -1
[ 17.531159] nvidia 0000:02:00.0: PCI INT A -> Link[APC4] -> GSI 19 (level, high) -> IRQ 19
[ 17.533994] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.22 Sun Nov 8 20:26:31 PST 2009
[ 17.847022] Console: switching to colour frame buffer device 80x30
[ 18.790645] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
[ 18.790660] Intel ICH 0000:00:06.0: PCI INT A -> Link[APCJ] -> GSI 21 (level, high) -> IRQ 21
[ 18.790735] Intel ICH 0000:00:06.0: setting latency timer to 64
[ 19.116038] intel8x0_measure_ac97_clock: measured 55315 usecs (2680 samples)
[ 19.116046] intel8x0: clocking to 48000
[ 19.883730] EXT3 FS on sda1, internal journal
[ 20.542049] kjournald starting. Commit interval 5 seconds
[ 20.542500] EXT3 FS on sda5, internal journal
[ 20.542511] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.672081] type=1505 audit(1278158385.561:5): operation="profile_load" pid=741 name="/usr/share/gdm/guest-session/Xsession"
[ 21.675915] type=1505 audit(1278158385.561:6): operation="profile_replace" pid=742 name="/sbin/dhclient3"
[ 21.677189] type=1505 audit(1278158385.565:7): operation="profile_replace" pid=742 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 21.677518] type=1505 audit(1278158385.565:8): operation="profile_replace" pid=742 name="/usr/lib/connman/scripts/dhclient-script"
[ 21.728394] type=1505 audit(1278158385.617:9): operation="profile_load" pid=743 name="/usr/bin/evince"
[ 21.736626] type=1505 audit(1278158385.625:10): operation="profile_load" pid=743 name="/usr/bin/evince-previewer"
[ 21.741614] type=1505 audit(1278158385.629:11): operation="profile_load" pid=743 name="/usr/bin/evince-thumbnailer"
[ 21.840606] type=1505 audit(1278158385.730:12): operation="profile_load" pid=752 name="/usr/lib/cups/backend/cups-pdf"
[ 21.841278] type=1505 audit(1278158385.730:13): operation="profile_load" pid=752 name="/usr/sbin/cupsd"
[ 21.978162] type=1505 audit(1278158385.867:14): operation="profile_load" pid=753 name="/usr/sbin/tcpdump"
[ 22.978997] eth0: no link during initialization.
[ 22.979464] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.997670] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 26.624423] agpgart-nvidia 0000:00:00.0: AGP 3.0 bridge
[ 26.624448] agpgart-nvidia 0000:00:00.0: putting AGP V3 device into 8x mode
[ 26.624525] nvidia 0000:02:00.0: putting AGP V3 device into 8x mode
[ 59.422430] ndiswrapper (iw_set_auth:1602): invalid cmd 12
[ 60.443761] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 71.228040] wlan0: no IPv6 routers present
[ 74.697824] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 74.697835] ata1.00: BMDMA stat 0x64
[ 74.697844] ata1.00: failed command: WRITE DMA
[ 74.697857] ata1.00: cmd ca/00:00:81:d0:4e/00:00:00:00:00/e4 tag 0 dma 131072 out
[ 74.697860] res 51/84:01:80:d1:4e/00:00:00:00:00/e4 Emask 0x10 (ATA bus error)
[ 74.697866] ata1.00: status: { DRDY ERR }
[ 74.697870] ata1.00: error: { ICRC ABRT }
[ 74.697912] ata1: soft resetting link
[ 74.860586] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 74.868454] ata1.00: configured for UDMA/33
[ 74.868483] ata1: EH complete
[ 87.246094] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 87.246105] ata1.00: BMDMA stat 0x64
[ 87.246113] ata1.00: failed command: WRITE DMA
[ 87.246126] ata1.00: cmd ca/00:08:5f:1a:6c/00:00:00:00:00/e0 tag 0 dma 4096 out
[ 87.246129] res 51/84:01:66:1a:6c/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 87.246134] ata1.00: status: { DRDY ERR }
[ 87.246139] ata1.00: error: { ICRC ABRT }
[ 87.246182] ata1: soft resetting link
[ 87.520569] ata1: nv_mode_filter: 0x739f&0x3f39f->0x739f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 87.528444] ata1.00: configured for UDMA/33
[ 87.528469] ata1: EH complete
[ 89.524277] ondemand governor failed, too long transition latency of HW, fallback to performance governor
[ 92.505693] ata1.00: limiting speed to PIO4
[ 92.505705] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 92.505713] ata1.00: BMDMA stat 0x64
[ 92.505721] ata1.00: failed command: WRITE DMA
[ 92.505734] ata1.00: cmd ca/00:08:d9:f2:4e/00:00:00:00:00/e4 tag 0 dma 4096 out
[ 92.505737] res 51/84:01:e0:f2:4e/00:00:00:00:00/e4 Emask 0x10 (ATA bus error)
[ 92.505742] ata1.00: status: { DRDY ERR }
[ 92.505747] ata1.00: error: { ICRC ABRT }
[ 92.505789] ata1: soft resetting link
[ 92.668587] ata1: nv_mode_filter: 0x1f&0x3f39f->0x1f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 92.676456] ata1.00: configured for PIO4
[ 92.676482] ata1: EH complete
[ 127.245241] gvfsd-metadata[1351]: segfault at 8 ip 0804d35a sp bfdf97d0 error 4 in gvfsd-metadata[8048000+c000]
Jádro: 2.6.32-22-generic
Setkal jste s se s tím někdo?
-
Párkrát se mi to taky stalo a systém zamrzl tak, že pomohl jenom tvrdý restart.
-
Updatuj. Co jádro xxx23-generic?
-
Updatuj. Co jádro xxx23-generic?
Po aktualizaci systemu (jako myslim apt-get upgrade) se to zda byt v pohode, ale v seznamu aktualizaci byli myslim jen nejake knihovny, jadro nikoliv, tak asi nejaka chyba, co se opravila.
Tak jsem to zakřikl, po vypnutí a zapnutí stroje, problém opět zpět a opět v dmesg hlášky failed command: WRITE DMA atp. Bude to asi teda spíš hardwarový problém (?), ale test povrchu i smart se zdá být v pohodě, a disk nevydává žádné podivné zvuky, teplota taky v normálu. Tak nevim, co by s tim diskem jinak mohlo bejt, leda změřit napětí zdroje? Zkusim teda to jiné jádro...
-
Vypisuje chyby DMA komunikácie. Skontroloval by som datový a napájací kábel.
-
Vypisuje chyby DMA komunikácie. Skontroloval by som datový a napájací kábel.
Díky za nasměrování.
Vyměnil jsem datovej kabel, práce se o něco urychlila (v dmesg už nejsou vidět chybové hlášky), ale stále rychlost nedosahuje původních hodnot (systém je podle mě zpomalenej kvůli rychlosti disku, cpu zatíženo minimálně, swap skoro na nule)..., stále se s tím nedá přílíš pracovat...
sudo hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 480 MB in 2.00 seconds = 239.52 MB/sec
Timing buffered disk reads: 78 MB in 3.03 seconds = 25.73 MB/sec
jsou tyto hodnoty v normálu?
2.164130] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 2.164214] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 2.492516] ata2.00: ATA-6: WDC WD400BB-00JHA0, 05.01C05, max UDMA/100
[ 2.492605] ata2.00: 78165360 sectors, multi 16: LBA
[ 2.492723] ata2: nv_mode_filter: 0x3f39f&0x739f->0x739f, BIOS=0x7000 (0xc000) ACPI=0x701f (60:600:0x13)
[ 2.500436] ata2.00: configured for UDMA/33
[ 3.041576] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.066716] EXT3-fs: mounted filesystem with ordered data mode.
Chápu tenhle výpis dobře tak, že disk podporuje UDMA/100, ale systém si stejně nastaví UDMA/33? Pokud ano, tak protože někde vázně komunikace, nebo proto, že to mam blbě nastavený? :) Dík.
-
UDMA/33 bola maximálna rýchlosť so starým typom káblu.
Nový typ mal 2x viac drátov, každý druhý drát je uzemnený. Radič to dokáže otestovať a nastaviť rýchlosť.
Druhá možnosť - ak je na tom istom kábli aj CD/DVD mechanika radič sa prispôsobí pomalšiemu zariadeniu.
-
UDMA/33 bola maximálna rýchlosť so starým typom káblu.
Nový typ mal 2x viac drátov, každý druhý drát je uzemnený. Radič to dokáže otestovať a nastaviť rýchlosť.
Druhá možnosť - ak je na tom istom kábli aj CD/DVD mechanika radič sa prispôsobí pomalšiemu zariadeniu.
Ad první možnost) Takže musim nějak říct systému, že už může přidat, že má lepší kabel? :) Ad druhá možnost) optickou mechaniku jsem odpojil, disk je na kabelu sám...
-
Tak jsem tam vrazil ještě jinej kabel k disku a ted...
dmesg |grep ata
[ 0.000000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] modified: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] Memory: 500400k/524224k available (4673k kernel code, 22988k reserved, 2121k data, 656k init, 0k highmem)
[ 0.000000] .data : 0xc0590663 - 0xc07a2e48 (2121 kB)
[ 0.263375] libata version 3.00 loaded.
[ 0.316989] cpufreq-nforce2: FSB changing is maybe unstable and can lead to crashes and data loss.
[ 0.451877] pata_acpi 0000:00:09.0: setting latency timer to 64
[ 1.134498] Write protecting the kernel read-only data: 1840k
[ 1.623409] pata_amd 0000:00:09.0: version 0.4.1
[ 1.623533] pata_amd 0000:00:09.0: setting latency timer to 64
[ 1.624989] scsi0 : pata_amd
[ 1.635645] scsi1 : pata_amd
[ 1.637210] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 1.637294] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.964536] ata2.00: ATA-6: WDC WD400BB-00JHA0, 05.01C05, max UDMA/100
[ 1.964628] ata2.00: 78165360 sectors, multi 16: LBA
[ 1.964745] ata2: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc600) ACPI=0x3f01f (20:600:0x13)
[ 1.972459] ata2.00: configured for UDMA/100
[ 2.497181] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.765142] EXT3-fs: mounted filesystem with ordered data mode.
A teď to vypadá, že tam nastavil UDMA/100. Subjektivně se mi zdá, že třeba spuštění www prohlížeče, nebo přihlášení do gnome trvá trochu déle, ale už je to docela použitelný, takže prostě hardwarový problém.
-
Ten disk je 40GB? To už rychlejší nebude.