Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Obecná podpora => Téma založeno: gogo21 26 Srpna 2010, 22:21:20
-
Nainštaloval som 10.4 32bit. Zo synaptiku som stiahol a nainštaloval xsane. Pri zapnutí scanera (Epson stylus CX3650, multifunkčné zariadenie) a spustení xsane sa zobrazí hlásenie: "chyba počas CMS konverzíí: Nie je možné otvoriť ICM profile scanera: Zatvoriť". Xsane som odinštaloval a preinštaloval niekoľko krát ale nič sa nezmenilo. V predchádzajúcej verzii 9.04 scaner pracoval bez závad. Taktiež aj teraz vo winxp pracuje bez závad. Čo je to CMS konverzia a ICM profile?
-
?Můžeš prosím tě zapnout scanner, otevřít Terminál (http://wiki.ubuntu.cz/Termin%C3%A1l), a dát tu výstup z příkazů
sane-find-scanner
scanimage -L
-
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
rudo@rudo-desktop:~$ scanimage -L
device `epson2:libusb:002:004' is a Epson CX3600 flatbed scanner
-
Ještě
sudo sane-find-scanner
lsusb
-
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
found USB scanner (vendor=0x04b8 [EPSON], product=0x080e [USB MFP]) at libusb:002:005
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
rudo@rudo-desktop:~$ lsusb
Bus 002 Device 005: ID 04b8:080e Seiko Epson Corp. CX-3500/3600/3650 MFP
Bus 002 Device 002: ID 093a:2510 Pixart Imaging, Inc. Hama Optical Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 058f:6377 Alcor Micro Corp. Multimedia Card Reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-
Zkus skenovat z příkazové řádky
scanimage -v > /tmp/test.pnm
Jestli skenování proběhlo, mrkni se na ten obrázek (/tmp/test.pnm). Je OK?
-
nascanovalo OK
-
Zkus v xsane najet do Nastavení a pohrát si s volbou enable color management (vypnout nebo zapnout, pak zkusit skenovat).
https://answers.launchpad.net/ubuntu/+source/xsane/+question/65736
-
Vyriešené. Bolo tam zafajkované "Povoliť správu farieb". Keď som odfajkoval, všetko začalo pracovať bez problémov. Ďakujem za radu.
-
Slováci mají "Povoliť správu farieb" přeložené a Česi nie?! To je nějaký binec! ;D