Fórum Ubuntu CZ/SK

Ostatní => Archiv => Téma založeno: dumi 16 Ledna 2007, 10:25:02

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 10:25:02

Az mi je trapne pisat, bo viem, ze problemy s netom sa tu riesili milionkrat, snazil som si to cele prejst, ale aj tak som nenasiel odpoved. Preto prosim prosim o pomoc: mam wired connection na eth1, v ubuntu 6.10 v system-správa-sieť som si nastavoval siet. v prvej zalozke (Connections) v properties k eth1 som zadal svoju staticku ip adresu, subnet mask aj default gateway, povolil som toto pripojenie. v dalsej zalozke (General) mi to hodilo nazov mojho pocitaca, nerobil som nic, v dalse zalozke (DNS) som do policka DNS Servers zadal adresu svojho dns servera a v poslednej zalozke (Hosts) som nerobil nic. ked si v terminali dam ifconfig eth1, vyhodi mi to toto:

eth1      Link encap:Ethernet  HWaddr 00:08:54:d6:1e:61  
          inet addr:10.105.2.30  Bcast:10.105.2.63  Mask:255.255.255.192
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:209 Base address:0x9000

Taze to vie o mojej sietovke, akurat to vobec nejde. kde robim chybu? este na zaver doplnim, ze mam AMD Pcnet-homebased network adapter, ze mi karta vobec neblika a ze nic neviem ani pingnut. Dik moc, ze mi venujete svoj cas a poradite mi.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 10:32:49

Poslete vypis souboru /etc/resolv.conf a prikazu route. Urcite je ta spravna sitova karta eth1? Neni to eth0?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 10:43:24

je to dobra sietovka, lebo MAC adresa sedi. udaje su tutola:

/etc/resolv.conf
nameserver 84.16.32.234

route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
10.105.2.0      *               255.255.255.192 U     0      0        0 eth1
default         10.105.2.1      0.0.0.0         UG    0      0        0 eth1


DNS je dobry.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 10:50:39

10.105.2.1 je adresa toho routeru? Podle vasi adresy a masky je vas adresni prostor 10.105.2.1-10.105.2.63, takze to vypada OK. Jde pingnout alespon na adresu toho routeru?
Pak uz zbyva jedine vadny kabel nebo poskozeny konektor na karte (nebo na routeru).

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 10:58:16

Neviem ci adresa roteru, vo win to je oznacene ako default gateway. jej hodnota je 10.105.2.1 a ano, broadcast address mam 10.105.2.63. nezda sa mi, ze by to mohol byt kabel, bo teraz pisem z win na tom istom pocitaci a cez tu istu kartu...

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 11:03:33

Co je to za sitovou kartu? Presny typ ve WIndows zjistite prikazem ipconfig /all.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 11:12:43

hodim to sem cele: ipconfig/all /prepis/

Windows IP Configuration

Host Name.....................: dumi
Primary Dns Suffix..........:
Node Type......................: Unknown
IP Routing Enabled........: No
WINS Proxy Enabled......: No

Ethernet adapter Local Area Connection 6:

Connection-specific DNS Suffix....:
Description..................................: AMD PCnet-Home Based Network Adapter

Physical Address.........................: 00-08-54-D6-1E-61
Dhcp Enabled..............................: No
IP Address..................................: 10.105.2.30
Subnet Mask...............................: 255.255.255.192
Default Gateway.........................: 10.105.2.1
DNS Servers................................: 84.16.32.234

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 11:30:38

aha, AMD PCnet-Home Based Network Adapter je oznaceni te sitove karty, ja myslel ze routeru.

stejny problem se stejnou sitovou kartou se resi tady: http://www.abclinuxu.cz/forum/show/98330
vypada to, ze tyhle karty nemaji rady linux :(

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 11:56:37

ach jaj, tam jeden cloviecik pisal, ze:
"mal som rovnaký problem. je to karta s čipsetom 79C978, ktorá má konektor aj na ethernet aj na ten telefón (čo spôsobuje problém). driver je pcnet32. treba ho naloadovať s parametrom pnahome=1 (čo som sa dočítal iba v zdrojáku). takže

modprobe pcnet32 pnahome=1

a potom stači reštartnuť sieť. "

tak mi uz iba prosim porad ako to mam urobit, bo sa do toho nevyznam. dik

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 16 Ledna 2007, 12:08:15

Takhle v konzoli:

sudo modprobe pcnet32 pnahome=1
sudo /etc/init.d/networking restart

Uspech je podminen tim, ze modul pcnet32 existuje.

Pokud to bude funkcni,
Je potreba provest jeste neco dalsiho.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 12:23:43

hmm, tak som to tam zadal a nic. ja to vzdavam, druhy den sa hram s tym netom a v ziadnej distribucii okrem knoppixu som to nerozbehal. ale knoppix nechcem, bo myslim ze na zaciatok moc zlozity na mna, tak asi ostanem pri win. do kelu

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 12:49:58

Musite bezpodminecne pouzivat tuto sitovou kartu? Nebylo by vhodne koupit v bazaru za dve stovky treba nejakou Intel Pro 100 nebo jinou normalni sitovku?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 12:55:59

porozmyslam, mozno by to bol aj dobry napad. kazdopadne dakujem moc za rady, velmo si to cenim, ze takto riesite problemy uplnych lam ako som ja. velmi dakujem

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 13:00:30

Naprosta vetsina beznych sitovych karet je v Ubuntu podporovana bez potreby doinstalovavat jakekoliv dalsi ovladace. Ta vase je bohuzel trochu exoticka.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 13:30:54

exoticka? pre ubuntu asi hej, ale inak neviem. a potrebujem taku, do ktorej ide telefonny kabel a nie lan, taze intel pro 100 mi nepomoze, ale uz browsujem net a hladam :)

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 13:48:09

Telefonni kabel do sitove karty? K cemu je to dobre?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Milhouse 16 Ledna 2007, 13:56:52

No mě to připadá, jako když člověk chce používat telefoní linku do síťové karty, místo do modemu. To by bylo překvápko! ;D

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 16 Ledna 2007, 14:27:21

No vysvetlete bliz jak je to s temi kabely. Jak vypadaji konektory, co kam vede a tak.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 14:42:34

ano ano, takze (pardon za kvalitu, ale fotene webcamerou):
http://img183.imageshack.us/img183/2486/kartamv8.png
http://img145.imageshack.us/img145/7177/detailvp9.png
kazdopadne je vidno, ze ten jeden oddeleny port je LAN a tie dva (na ciernom pozadi) su porty, do ktorych ide telefonny kabel (nie z telefonu, ale taky, ktory ma styri kontaktne body). pri jednom pise LINE a pri druhom TEL.
je jedno do ktoreho z tych dvoch ten sietovy kabel zapojim, net ide vo win cez oba. LAN kabel nemam vobec. takto mi to defaultne nastavil poskytovatel internetu. na strankach amd (http://www.amd.com/gb-uk/ConnectivitySolutions/ProductInformation/0,,50_2330_6629_2452%5E2525,00.html) som nasiel nejaky linux driver, skusim este ten spustit, aj ked sa obavam, ze moj malicky problem je vlastne mierne obludne velky..

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Milhouse 16 Ledna 2007, 15:30:19

Tak to vidím poprvé. Tohle je speciálka, vůbec se nedivím, že to nechodí hned od základu.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 16 Ledna 2007, 16:00:37

A to k vam jako vas poskytovatel dotahl internet po nejakem telefonnim kabelu? Porad nejak nechapu, co je to za technologii. ADSL to evidentne neni... Nebo se zkuste obratit na poskytovatele, treba maji v zaloze nejake jine reseni pro uzivatele Linuxu (hm, to jsem ale napsal peknou blbost, uznavam...)

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 16 Ledna 2007, 16:09:51

na streche mame mikrovlnku a z nej je vyvedeny kabel az k nam, tot vsio.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 16 Ledna 2007, 16:31:32

Klasicky konektor RJ-11 jde i do zdirky pro RJ-45, podle toho, co vidim a ctu se jedna o kartu kombinovanou s modemem, zkuste tedy privod LAN dat do zdirky RJ-45. Co se tyce funkce - asi windriver prepina jednotlive zdirky podle toho, co je do ktere pripojene, K radne funkci i 100Mbit site staci jen 4 draty , tak mne napada ... ono to asi fungovat nebude (rj11 v rj45), protoze rozmisteni dratu je malinko jine.

Muj nazor - i kdyz koupite novou sitovku, budete muset udelat nasledujici:
1) ucvaknout rj-11 konektor
2) nacvaknout rj-45 konektor dle normy (prvni par na pin 1,2 druhy par na pin 3 a 6)

Ale osobne si myslim, ze by stacilo jen opravit kabel a pres konektor rj-45 jej dat do portu LAN

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 16 Ledna 2007, 19:17:33

S tim ucvakavanim kabelu bych nechvatal, jeste nevime vsechno. Je potreba se podivat do vypisu hardwaru windows / nastaveni site jak tam to zarizeni je nazvane. Kolik tam je nainstalovanych protokolu  a jak  vypada ten "telefonni kabel". Co je v te siroke tmave zdirce vedle "telefonni" ?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 16 Ledna 2007, 20:41:20

Citace: dumi

kazdopadne je vidno, ze ten jeden oddeleny port je LAN a tie dva (na ciernom pozadi) su porty, do ktorych ide telefonny kabel (nie z telefonu, ale taky, ktory ma styri kontaktne body). pri jednom pise LINE a pri druhom TEL.

Pokud je nahore nejake wifi zarizeni (klient), predpokladam, ze se jedna o patch kabel, ktery ma na jedne strane (u wifi zarizeni) klasicky RJ-45 konektor a dole z neznameho duvodu (chybejici konektor, nefunkcni sitova karta -- spatne nastaveny port pro LAN) konektor RJ-11

Udelejme to tedy jeste jinak, co je to za wifi zarizeni? Tim myslim nazev a typ.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 16 Ledna 2007, 20:54:18

A jak vime co je dole za konektor ?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 16 Ledna 2007, 21:23:58

Vzhledem k tomu, ze tazatel psal, ze se jedna o telefonni kabel a na obrazku je klasicka zdirka pro RJ-11 konektor, nepredpokladam, ze tam dava cokoliv jineho. Pokud je nahore RJ-45 a podle typu klientskeho zarizeni WiFi nezjistime, ze se jedna o technologii prenosu modem->modem pripadne xDSL (nic jineho u zdirek oznacenych jako Line, Phone a LAN neda ocekavat), mel bych pomerne jasno, co za kabel by mel byt pouzit a kam by mel byt pripojen.

Kazdopadne na strankach AMD je dokumentace a pekny FAQ:
http://www.amd.com/us-en/ConnectivitySolutions/ProductInformation/0,,50_2330_6629_2460~8309,00.html#8311

Q:   What is the difference between a phoneline setup and a CAT5 setup?
A:   A home phoneline network uses your existing in-home phone wiring to connect your computers. An Ethernet network uses standard Category 5 cable and Ethernet hub to connect your computers.

How does the Auto-detect feature in the driver Properties box work? How do I force operation with a specific PHY or port?
A:   The device driver Autodetects the ports available on the adapter in the following sequence:

    * External Ethernet PHY
    * 10BaseT port (Internal Ethernet Phy)
    * J11 port (phone)

If an external Ethernet connection is detected, the driver chooses external Ethernet port for data communication. If a link does not exist on the external Ethernet port, the driver checks if a link exists on the Internal Ethernet Phy. If a link exists, it chooses the Internal Ethernet Phy. If the internal PHY link doesn’t exist, it selects the RJ11 port.

If no links are detected, the driver defaults to the RJ11 port.

The user also has the option to force connection through a port using the Driver Properties dialog box.

Takze podle vseho je opravdu pouzita xDSL technologie prenosu dat

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 17 Ledna 2007, 00:31:02

skusim zodpovedat co viem:
1,windows tu kartu povazuje za LAN or High-Speed Internet
2,ak som spravne pochopil toto: http://en.wikipedia.org/wiki/RJ11,_RJ14,_RJ25, tak ja mam konektor RJ14 vyvedeny z LAN kabla (ostatne drotiky okrem tych styroch su ustrihnute), v user´s guide k sietovke sa pise, ze podporuje dva RJ-11 phone jacks a jeden 10Base-T RJ-45 port. Zapojeny je oranzovy a zeleny par drotikov (zeleny z vonku, oranzovy par v strede).
3, "Co je v te siroke tmave zdirce vedle ´telefonni´?"-ta "telefonna" je LAN a siroka tmava - v skutocnosti su tam dva uz spominane telefonne porty.
4, co mame za wifi netusim, mozem zavolat providerovi a spytat sa, ale asi by som potreboval mat uz konkretne poziadavky a vediet, co od neho chcem.
5, prekablovavat ten moj rj11 na rj45 by sice slo, ale jednak na to nemam naradie a jednak neviem, ci mi to zabezpeci funkcnost.
6, podla providera (www.micronet.sk) mam FWA pripojenie.
uff, som ani netusil ze moj problem skonci takto..:)

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 17 Ledna 2007, 01:13:54

a mozem este jednu vec sa spytat? na uz spominanych strankach AMD (http://www.amd.com/gb-uk/ConnectivitySolutions/ProductInformation/0,,50_2330_6629_2452%5E2525,00.html) som nasiel Linux Drivers. jednak su z roku 2000, jednak su pre SUSE a jednak neviem ci ich vobec mam skusat nainstalovat a ak ano tak ako. hmm?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: ped 17 Ledna 2007, 03:19:14

ale ak tam knoppix funguje.. nebolo by jednoduchsie keby niekto poradil ako z neho zistit nastavenie siete/modulov a skusit spravit rovnake nastavenie aj pod ubuntu?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 17 Ledna 2007, 06:53:20

Ano, to je spravny smer uvah. Premyslime o dratu a zbytecne. Z knoppixu se nastaveni site zjisti stejne jako v ubuntu.

ifconfig, lsmod, lshw, lspci.
dmesg a najit v nem moment zavadeni site.

Taky se docela muze stat, ze modul pro tu kartu v Ub. nenajdete.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 17 Ledna 2007, 08:35:18

tak teda pisem z knoppixu, tu su zistene udaje (len xcem povedat, ze v knoppixe mi rozoznava iba tu sietovku, taze ju hlasi ako eth0 a nie eth1), sietovku som si nakonfiguroval v programiku netcardconfig:

ifconfig

Kód: [Vybrat]

eth0      Link encap:Ethernet  HWaddr 00:08:54:D6:1E:61
          inet addr:10.105.2.30  Bcast:10.105.2.63  Mask:255.255.255.192
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:335 errors:0 dropped:0 overruns:0 frame:0
          TX packets:338 errors:0 dropped:0 overruns:0 carrier:0
          collisions:112 txqueuelen:1000
          RX bytes:362111 (353.6 KiB)  TX bytes:54947 (53.6 KiB)
          Interrupt:18 Base address:0x9000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:6 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:300 (300.0 b)  TX bytes:300 (300.0 b)lsmod

Kód: [Vybrat]

Module                  Size  Used by    Not tainted
autofs4                 8756   1 (autoclean)
af_packet              13544   0 (autoclean)
nls_iso8859-1           2844   0 (autoclean)
nls_cp437               4348   0 (autoclean)
soundcore               3428   0 (autoclean)
agpgart                42724   0 (unused)
pcnet32                17188   1
mii                     2240   0 [pcnet32]
crc32                   2816   0 [pcnet32]
serial                 52100   0 (autoclean)
mousedev                3832   1
hid                    22564   0 (unused)
input                   3168   0 [mousedev hid]
pcmcia_core            39840   0
thermal                 6724   0 (unused)
processor               9008   0 [thermal]
fan                     1600   0 (unused)
button                  2700   0 (unused)
battery                 5952   0
ac                      1824   0
rtc                     7036   0 (autoclean)
cloop                   8740   2
sbp2                   16396   0 (unused)
ohci1394               22664   0 (unused)
ieee1394              183076   0 [sbp2 ohci1394]
usb-storage            61760   0 (unused)
usb-ohci               17896   0 (unused)
usbcore                57600   1 [hid usb-storage usb-ohci]
ataraid                 6180   0
ide-scsi                8816   1lshw

Kód: [Vybrat]

bash: lshw: command not foundlspci

Kód: [Vybrat]

0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1)
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
0000:00:01.0 ISA bridge: nVidia Corporation: Unknown device 0080 (rev a3)
0000:00:01.1 SMBus: nVidia Corporation: Unknown device 0084 (rev a1)
0000:00:02.0 USB Controller: nVidia Corporation: Unknown device 0087 (rev a1)
0000:00:02.1 USB Controller: nVidia Corporation: Unknown device 0087 (rev a1)
0000:00:02.2 USB Controller: nVidia Corporation: Unknown device 0088 (rev a2)
0000:00:04.0 Bridge: nVidia Corporation: Unknown device 008c (rev a3)
0000:00:06.0 Multimedia audio controller: nVidia Corporation: Unknown device 008a (rev a1)
0000:00:08.0 PCI bridge: nVidia Corporation: Unknown device 008b (rev a3)
0000:00:09.0 IDE interface: nVidia Corporation: Unknown device 0085 (rev a3)
0000:00:0b.0 IDE interface: nVidia Corporation: Unknown device 008e (rev a3)
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
0000:02:0a.0 Ethernet controller: Advanced Micro Devices [AMD] 79c978 [HomePNA] (rev 52)
0000:02:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)dmesg

Kód: [Vybrat]

CPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 22) *0, disabled.
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
00:00:01[A] -> 2-23 -> IRQ 23 level low
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
00:00:02[A] -> 2-21 -> IRQ 21 level high
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
00:00:02[b] -> 2-20 -> IRQ 20 level high
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
ACPI: PCI Interrupt Link [APCI] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [APCI] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [APCI] enabled at IRQ 21
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
ACPI: PCI Interrupt Link [APCK] enabled at IRQ 21
ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 20
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
00:00:0b[A] -> 2-22 -> IRQ 22 level high
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
00:02:06[A] -> 2-18 -> IRQ 18 level low
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
00:02:06[b] -> 2-19 -> IRQ 19 level low
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
00:02:06[C] -> 2-16 -> IRQ 16 level low
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
00:02:06[D] -> 2-17 -> IRQ 17 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 000 00  1    0    0   0   0    0    0    00
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  1    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    1    0   0   0    1    1    71
 0a 001 01  0    0    0   0   0    1    1    79
 0b 001 01  0    0    0   0   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 001 01  1    1    0   1   0    1    1    D9
 11 001 01  1    1    0   1   0    1    1    E1
 12 001 01  1    1    0   1   0    1    1    C9
 13 001 01  1    1    0   1   0    1    1    D1
 14 001 01  1    1    0   0   0    1    1    B9
 15 001 01  1    1    0   0   0    1    1    B1
 16 001 01  1    1    0   0   0    1    1    C1
 17 001 01  1    1    0   1   0    1    1    A9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xd0000000, mapped to 0xe0815000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:e340
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2-U400R: IDE controller at PCI slot 00:09.0
NFORCE2-U400R: chipset revision 163
NFORCE2-U400R: not 100% native mode: will probe irqs later
NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2-U400R: 00:09.0 (rev a3) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
NFORCE2-U400R-SATA: IDE controller at PCI slot 00:0b.0
NFORCE2-U400R-SATA: chipset revision 163
NFORCE2-U400R-SATA: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2-U400R-SATA: 00:0b.0 (rev a3) UDMA133 controller
NFORCE2-U400R-SATA: 100% native mode on irq 22
    ide2: BM-DMA at 0xac00-0xac07, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0xac08-0xac0f, BIOS settings: hdg:pio, hdh:pio
hda: WDC AC14300R, ATA DISK drive
hdb: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
hde: WDC WD800JD-00LSA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0x9f0-0x9f7,0xbf2 on irq 22
hda: attached ide-disk driver.
hda: host protected area => 1
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 8421840 sectors (4312 MB) w/512KiB Cache, CHS=524/255/63
hde: attached ide-disk driver.
hde: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hde: task_no_data_intr: error=0x04 { DriveStatusError }
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=9729/255/63
Partition check:
 hda: hda1 hda2 hda3 < hda5 >
 hde: hde1 hde2 < hde5 hde6 >
ide: late registration of driver.
SCSI subsystem driver Revision: 1.00
libata version 1.02 loaded.
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 781k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
hdb: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: HL-DT-ST  Model: DVDRAM GSA-4163B  Rev: A104
  Type:   CD-ROM                             ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
NCR53c406a: no available ports found
aec671x_detect:
scsi: Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18k (Release Date: Thu Aug 28 10:05:11 EDT 2003)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
Guestimating sector 8420879 for superblock
Guestimating sector 156280064 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
Medley RAID: No usable RAID sets found
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 00:50:50 Aug  9 2004
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:02.0 to 64
usb-ohci.c: USB OHCI at membase 0xe0b35000, IRQ 21
usb-ohci.c: usb-00:02.0, PCI device 10de:0087 (nVidia Corporation)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
PCI: Setting latency timer of device 00:02.1 to 64
usb-ohci.c: USB OHCI at membase 0xe0b37000, IRQ 20
usb-ohci.c: usb-00:02.1, PCI device 10de:0087 (nVidia Corporation)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 4 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
ohci1394: $Rev: 1045 $ Ben Collins
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[19]  MMIO=[e0001000-e00017ff]  Max Packet=[2048]
sbp2: $Rev: 1074 $ Ben Collins
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00006b252b]
hub.c: new USB device 00:02.1-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x458/0x36) is not claimed by any active driver.
hub.c: new USB device 00:02.1-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x93a/0x2471) is not claimed by any active driver.
scsi singledevice 0 0 0 0
scsi singledevice 0 0 1 0
scsi singledevice 0 0 2 0
scsi singledevice 0 0 3 0
scsi singledevice 0 0 4 0
scsi singledevice 0 0 5 0
scsi singledevice 0 0 6 0
scsi singledevice 0 0 7 0
scsi singledevice 0 1 0 0
scsi singledevice 0 1 1 0
scsi singledevice 0 1 2 0
scsi singledevice 0 1 3 0
scsi singledevice 0 1 4 0
scsi singledevice 0 1 5 0
scsi singledevice 0 1 6 0
scsi singledevice 0 1 7 0
scsi singledevice 1 0 0 0
scsi singledevice 1 0 1 0
scsi singledevice 1 0 2 0
scsi singledevice 1 0 3 0
scsi singledevice 1 0 4 0
scsi singledevice 1 0 5 0
scsi singledevice 1 0 6 0
scsi singledevice 1 0 7 0
scsi singledevice 1 1 0 0
scsi singledevice 1 1 1 0
scsi singledevice 1 1 2 0
scsi singledevice 1 1 3 0
scsi singledevice 1 1 4 0
scsi singledevice 1 1 5 0
scsi singledevice 1 1 6 0
scsi singledevice 1 1 7 0
scsi singledevice 2 0 0 0
scsi singledevice 2 0 1 0
scsi singledevice 2 0 2 0
scsi singledevice 2 0 3 0
scsi singledevice 2 0 4 0
scsi singledevice 2 0 5 0
scsi singledevice 2 0 6 0
scsi singledevice 2 0 7 0
scsi singledevice 2 1 0 0
scsi singledevice 2 1 1 0
scsi singledevice 2 1 2 0
scsi singledevice 2 1 3 0
scsi singledevice 2 1 4 0
scsi singledevice 2 1 5 0
scsi singledevice 2 1 6 0
scsi singledevice 2 1 7 0
scsi singledevice 3 0 0 0
scsi singledevice 3 0 1 0
scsi singledevice 3 0 2 0
scsi singledevice 3 0 3 0
scsi singledevice 3 0 4 0
scsi singledevice 3 0 5 0
scsi singledevice 3 0 6 0
scsi singledevice 3 0 7 0
scsi singledevice 3 1 0 0
scsi singledevice 3 1 1 0
scsi singledevice 3 1 2 0
scsi singledevice 3 1 3 0
scsi singledevice 3 1 4 0
scsi singledevice 3 1 5 0
scsi singledevice 3 1 6 0
scsi singledevice 3 1 7 0
scsi singledevice 4 0 0 0
scsi singledevice 4 0 1 0
scsi singledevice 4 0 2 0
scsi singledevice 4 0 3 0
scsi singledevice 4 0 4 0
scsi singledevice 4 0 5 0
scsi singledevice 4 0 6 0
scsi singledevice 4 0 7 0
scsi singledevice 4 1 0 0
scsi singledevice 4 1 1 0
scsi singledevice 4 1 2 0
scsi singledevice 4 1 3 0
scsi singledevice 4 1 4 0
scsi singledevice 4 1 5 0
scsi singledevice 4 1 6 0
scsi singledevice 4 1 7 0
scsi singledevice 5 0 0 0
scsi singledevice 5 0 1 0
scsi singledevice 5 0 2 0
scsi singledevice 5 0 3 0
scsi singledevice 5 0 4 0
scsi singledevice 5 0 5 0
scsi singledevice 5 0 6 0
scsi singledevice 5 0 7 0
scsi singledevice 5 1 0 0
scsi singledevice 5 1 1 0
scsi singledevice 5 1 2 0
scsi singledevice 5 1 3 0
scsi singledevice 5 1 4 0
scsi singledevice 5 1 5 0
scsi singledevice 5 1 6 0
scsi singledevice 5 1 7 0
scsi singledevice 6 0 0 0
scsi singledevice 6 0 1 0
scsi singledevice 6 0 2 0
scsi singledevice 6 0 3 0
scsi singledevice 6 0 4 0
scsi singledevice 6 0 5 0
scsi singledevice 6 0 6 0
scsi singledevice 6 0 7 0
scsi singledevice 6 1 0 0
scsi singledevice 6 1 1 0
scsi singledevice 6 1 2 0
scsi singledevice 6 1 3 0
scsi singledevice 6 1 4 0
scsi singledevice 6 1 5 0
scsi singledevice 6 1 6 0
scsi singledevice 6 1 7 0
scsi singledevice 7 0 0 0
scsi singledevice 7 0 1 0
scsi singledevice 7 0 2 0
scsi singledevice 7 0 3 0
scsi singledevice 7 0 4 0
scsi singledevice 7 0 5 0
scsi singledevice 7 0 6 0
scsi singledevice 7 0 7 0
scsi singledevice 7 1 0 0
scsi singledevice 7 1 1 0
scsi singledevice 7 1 2 0
scsi singledevice 7 1 3 0
scsi singledevice 7 1 4 0
scsi singledevice 7 1 5 0
scsi singledevice 7 1 6 0
scsi singledevice 7 1 7 0
blk: queue c03661a0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0366a78, I/O limit 4095Mb (mask 0xffffffff)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.01
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 27791 blocks, 65536 bytes/block, largest block is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 144k freed
Real Time Clock Driver v1.10f
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
usb-uhci.c: $Revision: 1.275 $ time 00:50:50 Aug  9 2004
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input: USB HID v1.10 Mouse [Genius NetScroll + Mini Traveler] on usb2:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
scsi singledevice 0 0 1 0
scsi singledevice 0 0 2 0
scsi singledevice 0 0 3 0
scsi singledevice 0 0 4 0
scsi singledevice 0 0 5 0
scsi singledevice 0 0 6 0
scsi singledevice 0 0 7 0
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
pcnet32.c:v1.30c 05.25.2004 tsbogend@alpha.franken.de
pcnet32: media reset to 0x8181.
pcnet32: PCnet/Home 79C978 at 0x9000, 00 08 54 d6 1e 61 assigned IRQ 18.
eth0: registered as PCnet/Home 79C978
pcnet32: 1 cards_found.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xd8000000
Adding Swap: 168640k swap-space (priority -1)

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 17 Ledna 2007, 10:24:20

Zbytecne o kabelu mluvime jen v pripade, ze (jak bylo receno drive) by bylo lepsi koupit novou sitovku za dve stovky. Sitovka se mi jevi spravne nastavena i pod ubuntu, videl bych to na problem s modulem (a dost mozna opravdu i s spatnym nastavenim primarni diry ze ktere se bere signal, coz je zalezitost modulu)

Poprosil bych jeste o lsmod, dmesg a lspci z ubuntu

Mozna bude problem s tim parametrem u modprobe pcnet32 pnahome=1
v te diskuzi, kde tento prispevek (ohledne modulu) nekdo resil, zaroven borec psal, ze mu to funguje az tak na treti ctvrty pokus ...

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 17 Ledna 2007, 11:21:51

tak teda ubuntu si o mojom systeme mysli toto:

lsmod

Kód: [Vybrat]

Module                  Size  Used by
nls_utf8                3200  1
nls_cp437               6912  1
vfat                   14720  1
fat                    56348  1 vfat
usb_storage            75072  1
libusual               17040  1 usb_storage
binfmt_misc            13448  1
rfcomm                 42260  0
l2cap                  27136  5 rfcomm
bluetooth              53476  4 rfcomm,l2cap
ipv6                  272288  10
cpufreq_userspace       5408  0
cpufreq_stats           7744  0
freq_table              6048  1 cpufreq_stats
cpufreq_powersave       2944  0
cpufreq_ondemand        8876  0
cpufreq_conservative     8712  0
video                  17540  0
tc1100_wmi              8324  0
sony_acpi               6412  0
sbs                    16804  0
pcc_acpi               14080  0
i2c_ec                  6272  1 sbs
hotkey                 11556  0
dev_acpi               12292  0
container               5632  0
button                  7952  0
battery                11652  0
asus_acpi              17688  0
ac                      6788  0
af_packet              24584  0
sbp2                   24584  0
lp                     12964  0
tsdev                   9152  0
spca5xx               637648  0
sg                     37404  0
snd_intel8x0           34844  1
snd_ac97_codec         97696  1 snd_intel8x0
snd_ac97_bus            3456  1 snd_ac97_codec
videodev               10752  1 spca5xx
parport_pc             37796  1
usbhid                 45152  0
snd_pcm_oss            47360  0
snd_mixer_oss          19584  1 snd_pcm_oss
pcnet32                33796  0
mii                     6912  1 pcnet32
i2c_nforce2             8192  0
i2c_core               23424  2 i2c_ec,i2c_nforce2
nvidia_agp              9628  1
agpgart                34888  1 nvidia_agp
snd_pcm                84612  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer              25348  1 snd_pcm
snd                    58372  8 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
parport                39496  2 lp,parport_pc
shpchp                 42144  0
pci_hotplug            32828  1 shpchp
evdev                  11392  1
floppy                 63044  0
soundcore              11232  1 snd
snd_page_alloc         11400  2 snd_intel8x0,snd_pcm
psmouse                41352  0
pcspkr                  4352  0
serio_raw               8452  0
ext3                  142728  1
jbd                    62228  1 ext3
ehci_hcd               34696  0
ohci_hcd               22532  0
usbcore               134912  7 usb_storage,libusual,spca5xx,usbhid,ehci_hcd,ohci_hcd
ohci1394               37040  0
ieee1394              306104  2 sbp2,ohci1394
forcedeth              32268  0
ide_generic             2432  0
ide_cd                 33696  0
cdrom                  38944  1 ide_cd
ide_disk               18560  3
generic                 5764  0
sd_mod                 22656  2
amd74xx                15260  0 [permanent]
sata_nv                11268  0
libata                 74892  1 sata_nv
scsi_mod              144648  5 usb_storage,sbp2,sg,sd_mod,libata
thermal                15624  0
processor              31560  1 thermal
fan                     6020  0
fbcon                  41504  0
tileblit                3840  1 fbcon
font                    9344  1 fbcon
bitblit                 7168  1 fbcon
softcursor              3328  1 bitblit
vesafb                  9244  0
capability              5896  0
commoncap               8704  1 capabilitylspci

Kód: [Vybrat]

00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1)
00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
00:01.0 ISA bridge: nVidia Corporation MCP2A ISA bridge (rev a3)
00:01.1 SMBus: nVidia Corporation MCP2A SMBus (rev a1)
00:02.0 USB Controller: nVidia Corporation MCP2A USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP2A USB Controller (rev a1)
00:02.2 USB Controller: nVidia Corporation MCP2A USB Controller (rev a2)
00:04.0 Bridge: nVidia Corporation MCP2A Ethernet Controller (rev a3)
00:06.0 Multimedia audio controller: nVidia Corporation MCP2S AC'97 Audio Controller (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP2A PCI Bridge (rev a3)
00:09.0 IDE interface: nVidia Corporation MCP2A IDE (rev a3)
00:0b.0 IDE interface: nVidia Corporation nForce2 Serial ATA Controller (rev a3)
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
02:0a.0 Ethernet controller: Advanced Micro Devices [AMD] 79c978 [HomePNA] (rev 52)
02:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)dmesg

Kód: [Vybrat]

[17179569.184000] Linux version 2.6.17-10-generic (root@vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu 2.6.17-10.33-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[17179569.184000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[17179569.184000]  BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 511MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f5b50
[17179569.184000] On node 0 totalpages: 131056
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   Normal zone: 126960 pages, LIFO batch:31
[17179569.184000] DMI 2.2 present.
[17179569.184000] ACPI: RSDP (v000 Nvidia                                ) @ 0x000f7580
[17179569.184000] ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
[17179569.184000] ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
[17179569.184000] ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7f40
[17179569.184000] ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x4008
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 6:8 APIC version 16
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: BIOS IRQ0 pin2 override ignored.
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] ACPI: IRQ14 used by override.
[17179569.184000] ACPI: IRQ15 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda2 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[17179569.184000] Detected 1743.090 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179572.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179572.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179572.012000] Memory: 509800k/524224k available (1910k kernel code, 13836k reserved, 1070k data, 308k init, 0k highmem)
[17179572.012000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179572.092000] Calibrating delay using timer specific routine.. 3489.91 BogoMIPS (lpj=6979826)
[17179572.092000] Security Framework v1.0.0 initialized
[17179572.092000] SELinux:  Disabled at boot.
[17179572.092000] Mount-cache hash table entries: 512
[17179572.092000] CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[17179572.092000] CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[17179572.092000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179572.092000] CPU: L2 Cache: 256K (64 bytes/line)
[17179572.092000] CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
[17179572.092000] Checking 'hlt' instruction... OK.
[17179572.108000] SMP alternatives: switching to UP code
[17179572.108000] Freeing SMP alternatives: 16k freed
[17179572.108000] checking if image is initramfs... it is
[17179572.644000] Freeing initrd memory: 5563k freed
[17179572.644000] ACPI: Core revision 20060707
[17179572.652000] ACPI: Looking for DSDT ... not found!
[17179572.652000] CPU0: AMD Sempron(tm)   2500+ stepping 01
[17179572.652000] Total of 1 processors activated (3489.91 BogoMIPS).
[17179572.652000] ENABLING IO-APIC IRQs
[17179572.652000] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[17179572.796000] Brought up 1 CPUs
[17179572.796000] migration_cost=0
[17179572.796000] NET: Registered protocol family 16
[17179572.796000] EISA bus registered
[17179572.796000] ACPI: bus type pci registered
[17179572.812000] PCI: PCI BIOS revision 2.10 entry at 0xfbe50, last bus=2
[17179572.812000] PCI: Using configuration type 1
[17179572.812000] Setting up standard PCI resources
[17179572.824000] ACPI: Interpreter enabled
[17179572.824000] ACPI: Using IOAPIC for interrupt routing
[17179572.828000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179572.828000] PCI: Probing PCI hardware (bus 00)
[17179572.832000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:09.0
[17179572.832000] Boot video device is 0000:01:00.0
[17179572.832000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179572.908000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[17179572.908000] ACPI: Power Resource [ISAV] (on)
[17179572.908000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[17179572.912000] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[17179572.912000] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.912000] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[17179572.912000] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[17179572.912000] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.912000] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[17179572.912000] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[17179572.912000] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[17179572.912000] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.916000] ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[17179572.916000] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.916000] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[17179572.916000] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[17179572.916000] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.916000] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.916000] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179572.916000] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[17179572.916000] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
[17179572.916000] ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21) *0, disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21) *0, disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21) *0, disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21) *0, disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21) *0, disabled.
[17179572.920000] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21) *0, disabled.
[17179572.924000] ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
[17179572.924000] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21) *0, disabled.
[17179572.924000] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21) *0, disabled.
[17179572.924000] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21) *0, disabled.
[17179572.924000] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21) *0, disabled.
[17179572.924000] ACPI: PCI Interrupt Link [APSI] (IRQs 22) *0, disabled.
[17179572.928000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179572.928000] pnp: PnP ACPI init
[17179572.936000] pnp: PnP ACPI: found 13 devices
[17179572.936000] PnPBIOS: Disabled by ACPI PNP
[17179572.936000] PCI: Using ACPI for IRQ routing
[17179572.936000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179572.980000] pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
[17179572.980000] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
[17179572.980000] pnp: 00:00: ioport range 0x4400-0x447f has been reserved
[17179572.980000] pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
[17179572.980000] pnp: 00:00: ioport range 0x4200-0x427f has been reserved
[17179572.980000] pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
[17179572.980000] pnp: 00:01: ioport range 0x5000-0x503f has been reserved
[17179572.980000] pnp: 00:01: ioport range 0x5100-0x513f has been reserved
[17179572.980000] PCI: Bridge: 0000:00:08.0
[17179572.980000]   IO window: 9000-9fff
[17179572.980000]   MEM window: e0000000-e0ffffff
[17179572.980000]   PREFETCH window: disabled.
[17179572.980000] PCI: Bridge: 0000:00:1e.0
[17179572.980000]   IO window: disabled.
[17179572.980000]   MEM window: e1000000-e2ffffff
[17179572.980000]   PREFETCH window: d0000000-d7ffffff
[17179572.980000] PCI: Setting latency timer of device 0000:00:08.0 to 64
[17179572.980000] NET: Registered protocol family 2
[17179573.020000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[17179573.020000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[17179573.020000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[17179573.020000] TCP: Hash tables configured (established 16384 bind 8192)
[17179573.020000] TCP reno registered
[17179573.020000] audit: initializing netlink socket (disabled)
[17179573.020000] audit(1169031989.020:1): initialized
[17179573.020000] VFS: Disk quotas dquot_6.5.1
[17179573.020000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179573.020000] Initializing Cryptographic API
[17179573.020000] io scheduler noop registered
[17179573.020000] io scheduler anticipatory registered
[17179573.020000] io scheduler deadline registered
[17179573.020000] io scheduler cfq registered (default)
[17179573.020000] isapnp: Scanning for PnP cards...
[17179573.376000] isapnp: No Plug & Play device found
[17179573.400000] Real Time Clock Driver v1.12ac
[17179573.400000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179573.400000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.400000] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.400000] mice: PS/2 mouse device common for all mice
[17179573.400000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179573.400000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179573.400000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179573.400000] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[17179573.400000] PNP: PS/2 controller doesn't have AUX irq; using default 12
[17179573.404000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179573.404000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179573.404000] EISA: Probing bus 0 at eisa.0
[17179573.404000] Cannot allocate resource for EISA slot 4
[17179573.404000] Cannot allocate resource for EISA slot 5
[17179573.404000] EISA: Detected 0 cards.
[17179573.404000] TCP bic registered
[17179573.404000] NET: Registered protocol family 1
[17179573.404000] NET: Registered protocol family 8
[17179573.404000] NET: Registered protocol family 20
[17179573.404000] Using IPI No-Shortcut mode
[17179573.404000] ACPI: (supports S0 S1 S4 S5)
[17179573.404000] Freeing unused kernel memory: 308k freed
[17179573.620000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179574.540000] Capability LSM initialized
[17179575.100000] SCSI subsystem initialized
[17179575.104000] libata version 1.20 loaded.
[17179575.108000] sata_nv 0000:00:0b.0: version 0.8
[17179575.108000] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
[17179575.108000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APSI] -> GSI 22 (level, high) -> IRQ 177
[17179575.108000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[17179575.108000] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xAC00 irq 177
[17179575.108000] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xAC08 irq 177
[17179575.312000] ata1: SATA link up 1.5 Gbps (SStatus 113)
[17179575.476000] ata1: dev 0 cfg 49:2f00 82:706b 83:7e01 84:4023 85:7068 86:3c01 87:4023 88:407f
[17179575.476000] ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48
[17179575.476000] nv_sata: Primary device added
[17179575.476000] nv_sata: Primary device removed
[17179575.476000] nv_sata: Secondary device removed
[17179575.484000] ata1: dev 0 configured for UDMA/133
[17179575.484000] scsi0 : sata_nv
[17179575.688000] ata2: SATA link down (SStatus 0)
[17179575.688000] scsi1 : sata_nv
[17179575.688000]   Vendor: ATA       Model: WDC WD800JD-00LS  Rev: 06.0
[17179575.688000]   Type:   Direct-Access                      ANSI SCSI revision: 05
[17179575.688000] NFORCE2-U400R: IDE controller at PCI slot 0000:00:09.0
[17179575.688000] NFORCE2-U400R: chipset revision 163
[17179575.688000] NFORCE2-U400R: not 100% native mode: will probe irqs later
[17179575.688000] NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
[17179575.688000] NFORCE2-U400R: 0000:00:09.0 (rev a3) UDMA133 controller
[17179575.688000]     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[17179575.688000]     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[17179575.688000] Probing IDE interface ide0...
[17179575.704000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[17179575.708000] sda: Write Protect is off
[17179575.708000] sda: Mode Sense: 00 3a 00 00
[17179575.708000] SCSI device sda: drive cache: write back
[17179575.708000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[17179575.708000] sda: Write Protect is off
[17179575.708000] sda: Mode Sense: 00 3a 00 00
[17179575.708000] SCSI device sda: drive cache: write back
[17179575.708000]  sda: sda1 sda2 < sda5 sda6 >
[17179575.744000] sd 0:0:0:0: Attached scsi disk sda
[17179575.976000] hda: WDC AC14300R, ATA DISK drive
[17179576.424000] hdb: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
[17179576.496000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179576.536000] Probing IDE interface ide1...
[17179577.112000] hda: max request size: 128KiB
[17179577.112000] hda: 8421840 sectors (4311 MB) w/512KiB Cache, CHS=8912/15/63
[17179577.112000] hda: cache flushes not supported
[17179577.112000]  hda: hda1 hda2 hda3 < hda5 >
[17179577.156000] hdb: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[17179577.156000] Uniform CD-ROM driver Revision: 3.20
[17179577.636000] Probing IDE interface ide1...
[17179577.692000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54.
[17179577.692000] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
[17179577.692000] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 21 (level, high) -> IRQ 185
[17179577.692000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[17179577.724000] ieee1394: Initialized config rom entry `ip1394'
[17179577.732000] usbcore: registered new driver usbfs
[17179577.732000] usbcore: registered new driver hub
[17179577.736000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179578.212000] eth0: forcedeth.c: subsystem: 01462:570c bound to 0000:00:04.0
[17179578.212000] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[17179578.212000] ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 193
[17179578.212000] PCI: Via IRQ fixup for 0000:02:0b.0, from 9 to 1
[17179578.264000] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
[17179578.264000] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, high) -> IRQ 201
[17179578.264000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[17179578.264000] ohci_hcd 0000:00:02.0: OHCI Host Controller
[17179578.264000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[17179578.264000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[193]  MMIO=[e0001000-e00017ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[17179578.280000] ohci_hcd 0000:00:02.0: irq 201, io mem 0xe3001000
[17179578.336000] usb usb1: configuration #1 chosen from 1 choice
[17179578.336000] hub 1-0:1.0: USB hub found
[17179578.336000] hub 1-0:1.0: 4 ports detected
[17179578.440000] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
[17179578.440000] ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [APCG] -> GSI 21 (level, high) -> IRQ 185
[17179578.440000] PCI: Setting latency timer of device 0000:00:02.1 to 64
[17179578.440000] ohci_hcd 0000:00:02.1: OHCI Host Controller
[17179578.440000] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[17179578.456000] ohci_hcd 0000:00:02.1: irq 185, io mem 0xe3002000
[17179578.512000] usb usb2: configuration #1 chosen from 1 choice
[17179578.512000] hub 2-0:1.0: USB hub found
[17179578.512000] hub 2-0:1.0: 4 ports detected
[17179578.616000] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
[17179578.616000] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 20 (level, high) -> IRQ 201
[17179578.616000] PCI: Setting latency timer of device 0000:00:02.2 to 64
[17179578.616000] ehci_hcd 0000:00:02.2: EHCI Host Controller
[17179578.616000] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
[17179578.616000] ehci_hcd 0000:00:02.2: debug port 1
[17179578.616000] PCI: cache line size of 64 is not supported by device 0000:00:02.2
[17179578.616000] ehci_hcd 0000:00:02.2: irq 201, io mem 0xe3003000
[17179578.616000] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179578.616000] usb usb3: configuration #1 chosen from 1 choice
[17179578.616000] hub 3-0:1.0: USB hub found
[17179578.616000] hub 3-0:1.0: 8 ports detected
[17179578.756000] Attempting manual resume
[17179578.784000] kjournald starting.  Commit interval 5 seconds
[17179578.784000] EXT3-fs: mounted filesystem with ordered data mode.
[17179579.544000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00006b252b]
[17179579.576000] usb 2-1: new low speed USB device using ohci_hcd and address 2
[17179579.788000] usb 2-1: configuration #1 chosen from 1 choice
[17179580.096000] usb 2-2: new full speed USB device using ohci_hcd and address 3
[17179580.308000] usb 2-2: configuration #1 chosen from 1 choice
[17179597.520000] input: PC Speaker as /class/input/input1
[17179597.688000] FDC 0 is a post-1991 82077
[17179597.784000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179597.796000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179598.576000] Linux agpgart interface v0.101 (c) Dave Jones
[17179598.620000] agpgart: Detected NVIDIA nForce2 chipset
[17179598.628000] agpgart: AGP aperture is 128M @ 0xd8000000
[17179598.672000] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
[17179598.672000] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
[17179598.740000] pcnet32.c:v1.32 18.Mar.2006 tsbogend@alpha.franken.de
[17179598.740000] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[17179598.740000] ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 209
[17179598.740000] pcnet32: media set to 10Mbit mode.
[17179598.740000] pcnet32: PCnet/Home 79C978 at 0x9000, 00 08 54 d6 1e 61 assigned IRQ 209.
[17179598.740000] eth1: registered as PCnet/Home 79C978
[17179598.740000] pcnet32: 1 cards_found.
[17179598.852000] eth1: link down
[17179598.872000] usbcore: registered new driver hiddev
[17179598.884000] input: Genius NetScroll + Mini Traveler as /class/input/input2
[17179598.884000] input: USB HID v1.10 Mouse [Genius NetScroll + Mini Traveler] on usb-0000:00:02.1-1
[17179598.884000] usbcore: registered new driver usbhid
[17179598.884000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179598.940000] parport: PnPBIOS parport detected.
[17179598.940000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[17179598.992000] Linux video capture interface: v1.00
[17179599.072000] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
[17179599.072000] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) -> IRQ 185
[17179599.072000] PCI: Setting latency timer of device 0000:00:06.0 to 64
[17179599.120000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[17179599.216000] drivers/media/video/spca5xx/spca5xx-main.c: USB SPCA5XX camera found. Genius VideoCam Ge111
[17179599.224000] usbcore: registered new driver spca5xx
[17179599.224000] drivers/media/video/spca5xx/spca5xx-main.c: spca5xx driver 00.57.08 registered
[17179599.268000] ts: Compaq touchscreen protocol output
[17179599.392000] intel8x0_measure_ac97_clock: measured 54651 usecs
[17179599.392000] intel8x0: clocking to 48000
[17179599.580000] lp0: using parport0 (interrupt-driven).
[17179599.612000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[17179599.612000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179599.648000] Adding 168640k swap on /dev/disk/by-uuid/682f2957-871b-4c38-868c-38e1a13ef76f.  Priority:-1 extents:1 across:168640k
[17179599.780000] EXT3 FS on hda2, internal journal
[17179601.296000] NET: Registered protocol family 17
[17179604.620000] ACPI: Power Button (FF) [PWRF]
[17179604.620000] ACPI: Power Button (CM) [PWRB]
[17179604.780000] ibm_acpi: ec object not found
[17179604.960000] pcc_acpi: loading...
[17179625.068000] NET: Registered protocol family 10
[17179625.068000] lo: Disabled Privacy Extensions
[17179625.068000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[17179625.068000] IPv6 over IPv4 tunneling driver
[17179628.368000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[17179628.368000] apm: overridden by ACPI.
[17179631.748000] Bluetooth: Core ver 2.8
[17179631.748000] NET: Registered protocol family 31
[17179631.748000] Bluetooth: HCI device and connection manager initialized
[17179631.748000] Bluetooth: HCI socket layer initialized
[17179631.796000] Bluetooth: L2CAP ver 2.8
[17179631.796000] Bluetooth: L2CAP socket layer initialized
[17179631.856000] Bluetooth: RFCOMM socket layer initialized
[17179631.856000] Bluetooth: RFCOMM TTY layer initialized
[17179631.856000] Bluetooth: RFCOMM ver 1.7
[17180133.120000] usb 3-1: new high speed USB device using ehci_hcd and address 4
[17180133.252000] usb 3-1: configuration #1 chosen from 1 choice
[17180133.392000] usbcore: registered new driver libusual
[17180133.488000] Initializing USB Mass Storage driver...
[17180133.488000] scsi2 : SCSI emulation for USB Mass Storage devices
[17180133.488000] usb-storage: device found at 4
[17180133.488000] usb-storage: waiting for device to settle before scanning
[17180133.488000] usbcore: registered new driver usb-storage
[17180133.488000] USB Mass Storage support registered.
[17180138.488000] usb-storage: device scan complete
[17180138.492000]   Vendor: USB 2.0   Model: Flash Disk        Rev: 0.00
[17180138.492000]   Type:   Direct-Access                      ANSI SCSI revision: 02
[17180138.492000] SCSI device sdb: 2048000 512-byte hdwr sectors (1049 MB)
[17180138.492000] sdb: Write Protect is off
[17180138.492000] sdb: Mode Sense: 00 00 00 00
[17180138.492000] sdb: assuming drive cache: write through
[17180138.496000] SCSI device sdb: 2048000 512-byte hdwr sectors (1049 MB)
[17180138.496000] sdb: Write Protect is off
[17180138.496000] sdb: Mode Sense: 00 00 00 00
[17180138.496000] sdb: assuming drive cache: write through
[17180138.496000]  sdb: sdb1
[17180138.756000] sd 2:0:0:0: Attached scsi removable disk sdb
[17180138.756000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[17180139.772000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 17 Ledna 2007, 12:14:44

Nemam moc casu na to koukat, vidim tam modul forcedeth, coz je modul pro integrovanou nvidia sitovku. Mel by byt zakazany. Proto se Vam ta karta hlasi jako eth1 a je v tom maglajz. Pokud tu masinu nebudete vyuzivat jako router, je potreba  popsat, jak to cele mate zapojene. Mam z toho divne pocity.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 17 Ledna 2007, 19:29:26

No zda se, ze modul forcedeth je stejne nevyuzit, klidne bych jej nechal, spis mne zaujal vypis z logu, konkretne:

Kód: [Vybrat]

[17179598.740000] pcnet32.c:v1.32 18.Mar.2006 tsbogend@alpha.franken.de
[17179598.740000] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[17179598.740000] ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 209
[17179598.740000] pcnet32: media set to 10Mbit mode.
[17179598.740000] pcnet32: PCnet/Home 79C978 at 0x9000, 00 08 54 d6 1e 61 assigned IRQ 209.
[17179598.740000] eth1: registered as PCnet/Home 79C978
[17179598.740000] pcnet32: 1 cards_found.
[17179598.852000] eth1: link downa

Kód: [Vybrat]

[17179625.068000] ADDRCONF(NETDEV_UP): eth1: link is not readyUplne nahodou, blbou trapnou nahodou, neni karta ve stavu down?
Zkuste do terminalu nabusit "sudo ifconfig eth1 up"

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 18 Ledna 2007, 14:33:39

dal som # ifconfig eth1 up a takisto nic. firefox nejde, pri pingnuti to vyhadzuje host unknown. a vzadu ani nesvieti zelene blikatko ked nam nieco s internetom robit, ako by karta na nic ani nereagovala, cista hibernacia.
Aby som zosumarizoval svoje pripojenie pre tych, ktori sa v tom stracaju: mam FWA pripojenie, na streche je mikrovlnka a z nej zvedeny kabel az mne do bytu. vyvedene mam z neho 4 kabliky do konektora RJ11. Sietovu kartu mam AMD PCnet-Home Based Network Adapter (Generic), ktory ma 1xRJ45 konektor a 2xRJ11. zapojeny kabel mam pochopitelne do konektora RJ11. ak mam ziskat nejake dalsie info od poskytovatela, dajte mi pls vediet ake.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 18 Ledna 2007, 14:45:17

Vidim tam modul mii, takze byste mohl zkusit diagnostiku pres mii. Nainstalujte si mii-tools a spuste mii-diag , pripadne mii-tool. jestli nesviti zelena, karta nema link,(nekomunikuje s druhym kioncem) takze asi nefunguje ovladac. Link je zaklad, pokud nebude, nema cenu zkouset konfiguraci site.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 18 Ledna 2007, 16:49:47

nic som neinstaloval, ale v terminali mi obidve funkcie normalne isli zadat, tu su hodnoty:

Kód: [Vybrat]

mii-diag
Using the default interface 'eth0'.
SIOCGMIIPHY on eth0 failed: Operation not supported

mii-tool
SIOCGMIIPHY on 'eth0' failed: Operation not supported
SIOCGMIIPHY on 'eth1' failed: Operation not supported
no MII interfaces foundak si mam nainstalovat mii-tools, mozes mi pls hodit na to link? bo som nasiel mrte mirrorov na vselico ohladom mii a nie je mi zrejme, ze co teda mam instalnut, dik.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 19 Ledna 2007, 07:01:33

Ne, podle vypisu uz tam jsou a kartu nedovedou, takze smula... Nebo mozna ta karta neni ziva, neni natazeny ovladac, resp. je, ale kartu nespustil.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 19 Ledna 2007, 09:34:10

Driver natazeny je a kartu spustil, ale asi si s ni dost dobre nerozumi (link down), jeste bych zkusil stahnout novou verzi driveru a bohuzel kompiloval

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 19 Ledna 2007, 09:45:07

Jestli ji spustil, tak by mely reagovat mii-tools, ne ? Aspon nahlasit link down.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 19 Ledna 2007, 09:48:00

taze si mam stiahnut novu verziu mii tools?
ci driver aky?

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Petr Merlin Vaněček 19 Ledna 2007, 10:50:26

mii-tools reagovat nemusi, ne vzdy je totiz karta podporovana
Kazdopadne jsem trosku googloval a nasel nasledujici prispevek:

I have AMD 79c978 based homepna card and I have used ubuntu since warty preview. Homepna have been tricky. With warty livecd homepna worked well. Warty install cd (preview) recognised this card as homepna. Card has link and act light. When detecting network cards link light went down. pcnet module was loaded in ethernet "mode". when pcnet32 homepna=1 was added to /etc/modules link light didn't go off in hotplug. Hoary was like warty. Hoary live don't recognise homepna card. If before detecting network hardware in live-expert opens shell and modprobe -rv pcnet32 and modprobe pcnet32 network is ok. Breezy is like hoary, but with linux-image-2.6.12-9 we need same modprobing again because pcnet32 is already loaded before /etc/modules.

Takze - modul pcnet32 je pravdepodobne zavaden s parametrem homepna=0, ktery rika, ze karta ma pracovat jako klasicka ethernet sitovka (cemuz by i odpovidalo link-down, protoze v RJ-45 neni zadny signal). Jak clanek radi, zkuste zadat do terminalu toto:

Kód: [Vybrat]

sudo modprobe -rv pcnet32
sudo modprobe pcnet32 homepna=1Tim odstranite natazeny modul s parametrem a znovu jej zavedete, predpokladam, ze diky parametru karta bude fungovat v homepna modu. Treba to povede k reseni.

[edit]Napsal jsem kraviny, opravil jsem[/edit]
[edit]Zajimava debata s moznym resenim je i zde
http://sourceforge.net/mailarchive/forum.php?forum_id=6401&max_rows=25&style=nested&viewmonth=200506
[/edit]

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 19 Ledna 2007, 11:28:33

ANOOOOOO! jooj, ta ja skocim totola ku plafonu! fungujeeee! wow, uch, ta to co totoooo! juchuuuu! dakujeeeeeem, paraada, uuuzasneeee, kraaasa. ta som myslel, ze mi ubuntu uz v zivote nepofici a ono to ide! som spravil teda totola:

Kód: [Vybrat]

sudo modprobe -rv pcnet32
sudo modprobe pcnet32 homepna=1
sudo /etc/init.d/networking restarta ide! sicko ideee, uff.
pardon za vykricniky a ine expresivne vyrazy, ale som naozaj dojaty. DAKUJEM VAM, ze ste boli ochotni venovat mi cas, poradit mi, snazit sa vyriesit problem, pricom VAS to stalo nemalo usilia a hladania na internete a chute bavit sa s uplnym zaciatocnikom. najuprimnejsie ako mozem Vam vsetkym vravim: DAKUJEM a klaniam sa. a teraz nie preto, ze sa moj problem vyriesil, ale preto, ze ste pre to urobili maximum (aj keby sa to nedalo by som Vam bol zaviazany). Pristup "linux guruov" na tomto fore ma nesmierne oslovil a velmi si ho vazim. Nakolko prechadzam na ubuntu verim, ze sa aj na tomto fore este stretneme. Dakujem, dakujem, dakujem!

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 19 Ledna 2007, 11:43:04

takze problem byl v tom, ze v diskuzi na kterou jsem odkazoval ( http://www.abclinuxu.cz/forum/show/98330?varianta=print ) pisatel v doporuceni chybne uvedl parametr pnahome=1, spravne ma byt homepna=1

koho by to napadlo....

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 19 Ledna 2007, 11:43:40

Jeste nezapomenout upravit /etc/modules.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 19 Ledna 2007, 11:46:47

do souboru /etc/modprobe.d/options pridejte radek

Kód: [Vybrat]

options pcnet32 homepna=1spravne nastaveni se pak provede pri kazdem startu pocitace, nebudete to muset delat rucne

dekuji: merlin, Pavelp i vsem ostatnim

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Pavelp 19 Ledna 2007, 11:55:10

Citace: lukas.svoboda

takze problem byl v tom, ze v diskuzi na kterou jsem odkazoval ( http://www.abclinuxu.cz/forum/show/98330?varianta=print ) pisatel v doporuceni chybne uvedl parametr pnahome=1, spravne ma byt homepna=1
koho by to napadlo....

To se mi jen zda ....

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 19 Ledna 2007, 12:01:50

s tym pridavanim riadku mam trochu problem, bo mam prava iba na read only. ako sa pls do da prehodit na root? bo z terminalu ten subor neviem spustit, d.

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: LS 19 Ledna 2007, 12:19:20

Citace: dumi

s tym pridavanim riadku mam trochu problem, bo mam prava iba na read only. ako sa pls do da prehodit na root? bo z terminalu ten subor neviem spustit, d.

Kód: [Vybrat]

sudo nano -w /etc/modprobe.d/optionsPred prikaz, ktery se ma spustit s pravy roota, pridejte "sudo". Viz. http://wiki.ubuntu.cz/Root_sudo

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: dumi 28 Ledna 2007, 22:39:08

dakujem, tak teda internet a vsetko uz v poriadku bezi, zacinam sa v tomto novom prostredi rozkukavat..
iba na zaver: chcel by som zmenit nazov svojho prispevku aby bol popisnejsi a aby som tam dodal, ze uz je moj problem vyrieseny a neviem to tu najst. mozte mi este s tymto pls helpnut abo admin to doplnit? dakujem a celkovo este raz dakujem za pristup a odpovede. gud lak!

Název: opat problemy s internetom [vyřešeno]
Přispěvatel: Milhouse 28 Ledna 2007, 23:26:13

Upravit název vlákna může jen moderátor a admin dané část fóra. Takže...

                                                                      [vyřešeno] :)