Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Hardware => Téma založeno: mrkrenek 19 Června 2013, 23:15:29
-
Zdravím,
Mám starší HP nc6120, a včera když jsem šel spát, a chtěl si zapnout nějakej seriál z disku, tak nešla myš, disk nic. Žádný ze 4 USB portů nefungoval.
Dnes večer je to stejné..
Myslíte že je to záležitost SW, nebo se prostě z ničeho nic "vysrali" komplet všechny ?
díky
honza@honza-HP-Compaq-nc6120-PY507EA-AKB:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-
Restartovals? Případně jej vypni a vytáhni na 20s aku.
-
Jinak v tom notebooku je jen jeden řadič, jestli odešel ten, tak samozřejmě vzal i všechny porty.
-
Restartovals? Případně jej vypni a vytáhni na 20s aku.
Restartoval jsem to ten první večer asi 10x, to nepomohlo, ale tu nabíječku vyndat zkusím
Jinak v tom notebooku je jen jeden řadič, jestli odešel ten, tak samozřejmě vzal i všechny porty.
Což by bylo ovšem nemilé :-\
Jednu chvíli to ale šlo, tak jsem rychle vykopíroval pár věcí. Potom jsem to zkusil zase odpojit a vypojit a opět to nešlo.
-
A funguje to mimo systém
-
A funguje to mimo systém
Nabootoval jsem teď Ubuntu 10.10 live a funguje jak myš, tak i externí disk.
A i v tom Ubuntu LTS co mám nainstalovaný na disku to teď funguje. Ale vsadím se, že večer až si zase budu chtít něco pustit, tak to nepujde
-
A neshazuje to nějaké zařízení, na Lenovu S205 mi určité druhy USB zařízení vždycky totálně shodili ovladač v jádře
-
Je to obyčejná myš od Lenova, externí disk je Verbatim.
Je nějakej log, do kterýho se můžu podívat, zda se to neděje ?
EDIT: teďka ten notebook běží asi 2 hodiny a všechna usb fungují
-
Až to zas spadne, zadej v terminálu prostě
dmesg měl by jsi vidět co selhalo
-
[ 28.846624] lib80211_crypt: registered algorithm 'TKIP'
[ 39.920172] eth1: no IPv6 routers present
[ 94.768186] usb 1-7: new high-speed USB device number 2 using ehci_hcd
[ 96.805542] Initializing USB Mass Storage driver...
[ 96.805751] usb-storage 1-7:1.0: Quirks match for vid 1058 pid 0704: 8000
[ 96.805797] scsi2 : usb-storage 1-7:1.0
[ 96.806003] usbcore: registered new interface driver usb-storage
[ 96.806009] USB Mass Storage support registered.
[ 97.804914] scsi 2:0:0:0: Direct-Access WD 3200BMV External 1.75 PQ: 0 ANSI: 4
[ 97.813453] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 97.814589] sd 2:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 97.815116] sd 2:0:0:0: [sdb] Write Protect is off
[ 97.815125] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 97.815614] sd 2:0:0:0: [sdb] No Caching mode page present
[ 97.815623] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 97.818420] sd 2:0:0:0: [sdb] No Caching mode page present
[ 97.818426] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 97.868323] sdb: sdb1
[ 97.870612] sd 2:0:0:0: [sdb] No Caching mode page present
[ 97.870622] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 97.870630] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 296.536075] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 296.844103] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 297.144116] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 297.444295] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 298.938114] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 299.204073] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 299.816134] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 302.164117] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 302.476072] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 302.784073] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 303.080067] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 303.384096] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 303.688112] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 303.984063] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 304.272081] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 304.548098] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 304.828095] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 305.128081] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 305.432096] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 305.732104] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 306.032087] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 306.332085] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 306.632091] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 306.765049] sd 2:0:0:0: [sdb] Unhandled error code
[ 306.765059] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 306.765070] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 f0 00
[ 306.765095] end_request: I/O error, dev sdb, sector 88000887
[ 306.765105] quiet_error: 39 callbacks suppressed
[ 306.765113] Buffer I/O error on device sdb1, logical block 11000103
[ 306.765129] Buffer I/O error on device sdb1, logical block 11000104
[ 306.765137] Buffer I/O error on device sdb1, logical block 11000105
[ 306.765144] Buffer I/O error on device sdb1, logical block 11000106
[ 306.765151] Buffer I/O error on device sdb1, logical block 11000107
[ 306.765159] Buffer I/O error on device sdb1, logical block 11000108
[ 306.765167] Buffer I/O error on device sdb1, logical block 11000109
[ 306.765174] Buffer I/O error on device sdb1, logical block 11000110
[ 306.765181] Buffer I/O error on device sdb1, logical block 11000111
[ 306.765189] Buffer I/O error on device sdb1, logical block 11000112
[ 306.888077] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 307.180076] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 307.468060] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 307.760069] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 308.032070] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 308.312083] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 308.444935] sd 2:0:0:0: [sdb] Unhandled error code
[ 308.444946] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 308.444956] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e ca 67 00 00 10 00
[ 308.444982] end_request: I/O error, dev sdb, sector 88001127
[ 308.592076] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 308.868079] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 309.132064] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 309.404079] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 309.680090] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 309.948227] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 310.080924] sd 2:0:0:0: [sdb] Unhandled error code
[ 310.080934] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 310.080945] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e ca 77 00 00 f0 00
[ 310.080969] end_request: I/O error, dev sdb, sector 88001143
[ 310.224208] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 310.496056] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 310.764234] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 311.020222] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 311.284087] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 311.560233] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 311.693270] sd 2:0:0:0: [sdb] Unhandled error code
[ 311.693280] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 311.693291] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e cb 67 00 00 10 00
[ 311.693316] end_request: I/O error, dev sdb, sector 88001383
[ 311.832198] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 312.096064] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 312.368231] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 312.636230] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 312.904231] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 313.176197] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 313.308953] sd 2:0:0:0: [sdb] Unhandled error code
[ 313.308962] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 313.308973] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 313.308998] end_request: I/O error, dev sdb, sector 88000887
[ 313.309008] quiet_error: 54 callbacks suppressed
[ 313.309015] Buffer I/O error on device sdb1, logical block 11000103
[ 313.432076] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 313.700223] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 313.956222] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 314.224205] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 314.492238] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 314.756218] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 314.889136] sd 2:0:0:0: [sdb] Unhandled error code
[ 314.889145] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 314.889156] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 314.889181] end_request: I/O error, dev sdb, sector 88000887
[ 314.889192] Buffer I/O error on device sdb1, logical block 11000103
[ 315.020220] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 315.276067] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 315.540238] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 315.796210] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 316.060199] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 316.328231] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 316.461415] sd 2:0:0:0: [sdb] Unhandled error code
[ 316.461425] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 316.461436] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 316.461461] end_request: I/O error, dev sdb, sector 88000887
[ 316.461473] Buffer I/O error on device sdb1, logical block 11000103
[ 316.588207] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 316.852233] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 317.112222] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 317.376227] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 317.632088] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 317.896200] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 318.029670] sd 2:0:0:0: [sdb] Unhandled error code
[ 318.029679] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 318.029690] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 97 00 00 08 00
[ 318.029714] end_request: I/O error, dev sdb, sector 88000919
[ 318.029725] Buffer I/O error on device sdb1, logical block 11000107
[ 318.180099] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 318.440067] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 318.696555] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 318.952086] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 319.208100] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 319.464089] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 319.597049] sd 2:0:0:0: [sdb] Unhandled error code
[ 319.597060] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 319.597071] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 319.597095] end_request: I/O error, dev sdb, sector 88000887
[ 319.597107] Buffer I/O error on device sdb1, logical block 11000103
[ 319.720087] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 319.976071] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 320.232087] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 320.488070] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 320.744077] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 321.000095] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 321.133259] sd 2:0:0:0: [sdb] Unhandled error code
[ 321.133270] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 321.133281] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 321.133305] end_request: I/O error, dev sdb, sector 88000887
[ 321.133317] Buffer I/O error on device sdb1, logical block 11000103
[ 321.256092] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 321.512059] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 321.768044] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 322.040091] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 322.296077] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 322.552090] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 322.685483] sd 2:0:0:0: [sdb] Unhandled error code
[ 322.685494] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 322.685505] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 322.685529] end_request: I/O error, dev sdb, sector 88000887
[ 322.685541] Buffer I/O error on device sdb1, logical block 11000103
[ 322.812089] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 322.954867] usb 1-7: device descriptor read/all, error -71
[ 323.068067] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 323.192081] usb 1-7: device descriptor read/64, error -71
[ 323.552060] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 323.695997] usb 1-7: device descriptor read/all, error -71
[ 323.814089] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 323.936221] usb 1-7: device descriptor read/64, error -71
[ 324.300049] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 324.556215] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 324.812208] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 325.068235] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 325.207305] sd 2:0:0:0: [sdb] Unhandled error code
[ 325.207313] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 325.207324] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 325.207349] end_request: I/O error, dev sdb, sector 88000887
[ 325.207361] Buffer I/O error on device sdb1, logical block 11000103
[ 325.328081] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 325.471961] usb 1-7: device descriptor read/all, error -71
[ 325.584243] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 325.708215] usb 1-7: device descriptor read/64, error -71
[ 326.068215] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 326.324201] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 326.467890] usb 1-7: device descriptor read/all, error -71
[ 326.580203] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 326.704210] usb 1-7: device descriptor read/64, error -71
[ 327.064098] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 327.320200] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 327.580107] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 327.723775] usb 1-7: device descriptor read/all, error -71
[ 327.836203] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 327.956197] usb 1-7: device descriptor read/64, error -71
[ 328.194904] sd 2:0:0:0: [sdb] Unhandled error code
[ 328.194914] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 328.194925] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 328.194949] end_request: I/O error, dev sdb, sector 88000887
[ 328.194959] Buffer I/O error on device sdb1, logical block 11000103
[ 328.316218] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 328.459294] usb 1-7: device descriptor read/all, error -71
[ 328.572195] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 328.692058] usb 1-7: device descriptor read/64, error -71
[ 329.056211] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 329.316216] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 329.572064] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 329.834097] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 330.092191] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 330.228142] sd 2:0:0:0: [sdb] Unhandled error code
[ 330.228150] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 330.228161] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 330.228185] end_request: I/O error, dev sdb, sector 88000887
[ 330.228198] Buffer I/O error on device sdb1, logical block 11000103
[ 330.348080] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 330.491457] usb 1-7: device descriptor read/all, error -71
[ 330.604229] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 330.724183] usb 1-7: device descriptor read/64, error -71
[ 331.084215] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 331.227433] usb 1-7: device descriptor read/all, error -71
[ 331.340203] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 331.460050] usb 1-7: device descriptor read/64, error -71
[ 331.828216] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 332.084050] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 332.344198] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 332.604083] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 332.739542] sd 2:0:0:0: [sdb] Unhandled error code
[ 332.739551] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 332.739562] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 332.739586] end_request: I/O error, dev sdb, sector 88000887
[ 332.739598] Buffer I/O error on device sdb1, logical block 11000103
[ 332.860208] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 333.120213] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 333.263202] usb 1-7: device descriptor read/all, error -71
[ 333.376209] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 333.496198] usb 1-7: device descriptor read/64, error -71
[ 333.872201] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 334.128051] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 334.388203] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 334.644074] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 334.780308] sd 2:0:0:0: [sdb] Unhandled error code
[ 334.780316] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 334.780327] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 334.780352] end_request: I/O error, dev sdb, sector 88000887
[ 334.780364] Buffer I/O error on device sdb1, logical block 11000103
[ 334.900225] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 335.156065] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 335.416108] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 335.672213] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 335.932065] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 336.200057] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 336.337376] sd 2:0:0:0: [sdb] Unhandled error code
[ 336.337385] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 336.337395] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 336.337420] end_request: I/O error, dev sdb, sector 88000887
[ 336.337433] Buffer I/O error on device sdb1, logical block 11000103
[ 336.460100] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 336.720211] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 336.980083] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 337.240215] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 337.504208] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 337.768231] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 337.900922] sd 2:0:0:0: [sdb] Unhandled error code
[ 337.900928] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 337.900934] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 337.900946] end_request: I/O error, dev sdb, sector 88000887
[ 337.900954] Buffer I/O error on device sdb1, logical block 11000103
[ 338.020077] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 338.292236] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 338.556060] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 338.816074] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 339.076201] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 339.332214] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 339.852055] usb 1-7: device not accepting address 2, error -71
[ 339.964187] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 340.084058] usb 1-7: device descriptor read/64, error -71
[ 340.324098] sd 2:0:0:0: [sdb] Unhandled error code
[ 340.324106] sd 2:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 340.324117] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 340.324142] end_request: I/O error, dev sdb, sector 88000887
[ 340.324153] Buffer I/O error on device sdb1, logical block 11000103
[ 340.444216] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 340.586647] usb 1-7: device descriptor read/all, error -71
[ 340.700214] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 340.820213] usb 1-7: device descriptor read/64, error -71
[ 341.188064] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 341.448046] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 341.592774] usb 1-7: device descriptor read/all, error -71
[ 341.708072] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 341.828069] usb 1-7: device descriptor read/64, error -71
[ 342.074609] usb 1-7: device descriptor read/all, error -71
[ 342.188131] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 342.596053] usb 1-7: device not accepting address 2, error -71
[ 342.708056] usb 1-7: reset high-speed USB device number 2 using ehci_hcd
[ 343.120209] usb 1-7: device not accepting address 2, error -71
[ 343.120267] usb 1-7: USB disconnect, device number 2
[ 343.130542] sd 2:0:0:0: [sdb] Unhandled error code
[ 343.130552] sd 2:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 343.130564] sd 2:0:0:0: [sdb] CDB: Read(10): 28 00 05 3e c9 77 00 00 08 00
[ 343.130588] end_request: I/O error, dev sdb, sector 88000887
[ 343.130600] Buffer I/O error on device sdb1, logical block 11000103
[ 343.336953] usb 1-7: new high-speed USB device number 3 using ehci_hcd
[ 343.456050] usb 1-7: device descriptor read/64, error -71
[ 343.703351] usb-storage 1-7:1.0: Quirks match for vid 1058 pid 0704: 8000
[ 343.704365] scsi3 : usb-storage 1-7:1.0
[ 344.820071] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 345.167719] usb 1-7: device descriptor read/all, error -71
[ 345.280039] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 345.407023] usb 1-7: device descriptor read/64, error -71
[ 345.764069] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 345.907275] usb 1-7: device descriptor read/all, error -71
[ 346.020077] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 346.140062] usb 1-7: device descriptor read/64, error -71
[ 346.387761] scsi 3:0:0:0: Direct-Access WD 3200BMV External 1.75 PQ: 0 ANSI: 4
[ 346.392607] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 346.393046] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 346.393520] sd 3:0:0:0: [sdb] Write Protect is off
[ 346.393529] sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 346.394747] sd 3:0:0:0: [sdb] No Caching mode page present
[ 346.394756] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 346.508074] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 346.649763] sd 3:0:0:0: [sdb] No Caching mode page present
[ 346.649774] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 346.780080] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 347.052062] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 347.308052] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 347.564058] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 347.707342] usb 1-7: device descriptor read/all, error -71
[ 347.820072] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 347.940050] usb 1-7: device descriptor read/64, error -71
[ 348.187470] usb 1-7: device descriptor read/all, error -71
[ 348.300067] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 348.712200] usb 1-7: device not accepting address 3, error -71
[ 348.824201] usb 1-7: reset high-speed USB device number 3 using ehci_hcd
[ 349.236062] usb 1-7: device not accepting address 3, error -71
[ 349.236123] usb 1-7: USB disconnect, device number 3
[ 349.244068] sd 3:0:0:0: [sdb] Unhandled error code
[ 349.244078] sd 3:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 349.244089] sd 3:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
[ 349.244114] end_request: I/O error, dev sdb, sector 0
[ 349.244124] Buffer I/O error on device sdb, logical block 0
[ 349.244534] ldm_validate_partition_table(): Disk read failed.
[ 349.244988] Dev sdb: unable to read RDB block 0
[ 349.245559] sdb: unable to read partition table
[ 349.248564] sd 3:0:0:0: [sdb] READ CAPACITY failed
[ 349.248573] sd 3:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 349.248583] sd 3:0:0:0: [sdb] Sense not available.
[ 349.248635] sd 3:0:0:0: [sdb] Asking for cache data failed
[ 349.248643] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 349.248651] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 349.360079] usb 1-7: new high-speed USB device number 4 using ehci_hcd
[ 349.484212] usb 1-7: device descriptor read/64, error -71
[ 349.727837] usb-storage 1-7:1.0: Quirks match for vid 1058 pid 0704: 8000
[ 349.727896] scsi4 : usb-storage 1-7:1.0
[ 350.844222] usb 1-7: reset high-speed USB device number 4 using ehci_hcd
[ 350.987520] usb 1-7: device descriptor read/all, error -71
[ 351.100082] usb 1-7: reset high-speed USB device number 4 using ehci_hcd
[ 351.236075] usb 1-7: device descriptor read/64, error -71
[ 351.517539] scsi 4:0:0:0: Direct-Access WD 3200BMV External 1.75 PQ: 0 ANSI: 4
[ 351.520484] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 351.521239] sd 4:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 351.521978] sd 4:0:0:0: [sdb] Write Protect is off
[ 351.521982] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 351.522765] sd 4:0:0:0: [sdb] No Caching mode page present
[ 351.522770] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 351.525256] sd 4:0:0:0: [sdb] No Caching mode page present
[ 351.525262] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 351.644080] usb 1-7: reset high-speed USB device number 4 using ehci_hcd
[ 351.791447] usb 1-7: device descriptor read/all, error -71
[ 351.910279] usb 1-7: reset high-speed USB device number 4 using ehci_hcd
[ 352.032192] usb 1-7: device descriptor read/64, error -71
[ 352.279660] usb 1-7: device descriptor read/all, error -71
[ 352.392190] usb 1-7: reset high-speed USB device number 4 using ehci_hcd
[ 352.804220] usb 1-7: device not accepting address 4, error -71
[ 352.916214] usb 1-7: reset high-speed USB device number 4 using ehci_hcd
[ 353.328192] usb 1-7: device not accepting address 4, error -71
[ 353.328244] usb 1-7: USB disconnect, device number 4
[ 353.336204] sd 4:0:0:0: [sdb] Unhandled error code
[ 353.336213] sd 4:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 353.336224] sd 4:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
[ 353.336248] end_request: I/O error, dev sdb, sector 0
[ 353.336258] Buffer I/O error on device sdb, logical block 0
[ 353.336663] ldm_validate_partition_table(): Disk read failed.
[ 353.337131] Dev sdb: unable to read RDB block 0
[ 353.337705] sdb: unable to read partition table
[ 353.340602] sd 4:0:0:0: [sdb] READ CAPACITY failed
[ 353.340610] sd 4:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 353.340620] sd 4:0:0:0: [sdb] Sense not available.
[ 353.340672] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 353.340680] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 353.340688] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 353.452223] usb 1-7: new high-speed USB device number 5 using ehci_hcd
[ 353.576073] usb 1-7: device descriptor read/64, error -71
[ 354.204187] usb 1-7: device not accepting address 5, error -71
[ 354.316066] usb 1-7: new high-speed USB device number 6 using ehci_hcd
[ 354.436201] usb 1-7: device descriptor read/64, error -71
[ 354.683883] usb 1-7: device descriptor read/all, error -71
[ 354.796226] usb 1-7: new high-speed USB device number 7 using ehci_hcd
[ 355.212053] usb 1-7: device not accepting address 7, error -71
[ 355.324212] usb 1-7: new high-speed USB device number 8 using ehci_hcd
[ 355.740210] usb 1-7: device not accepting address 8, error -71
[ 355.740250] hub 1-0:1.0: unable to enumerate USB device on port 7
[ 355.826927] uhci_hcd 0000:00:1d.3: host controller process error, something bad happened!
[ 355.826937] uhci_hcd 0000:00:1d.3: host controller halted, very bad!
[ 355.826959] uhci_hcd 0000:00:1d.3: HC died; cleaning up
[ 355.896177] hub 5-0:1.0: activate --> -19
[ 432.040409] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 432.228458] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 432.472194] usb 1-1: new high-speed USB device number 11 using ehci_hcd
[ 432.556416] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 432.768334] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 433.121662] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 433.360223] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 433.608358] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 433.906932] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 434.144201] usb 1-1: new high-speed USB device number 12 using ehci_hcd
[ 434.258131] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 434.600221] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 434.861712] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 435.100295] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 435.344476] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 435.596814] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 435.852300] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 436.093386] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 436.336683] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 436.605707] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 436.840229] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 437.131588] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 437.336710] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 437.576252] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 437.932468] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 438.320272] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 438.568595] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 438.824453] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 439.077393] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 439.312271] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 439.573915] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 439.808263] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 440.056550] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 440.308181] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 440.564387] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 440.801956] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 441.092469] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 441.315353] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 441.552435] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 441.796420] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 442.050417] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 442.416206] usb 1-1: new high-speed USB device number 13 using ehci_hcd
[ 442.544707] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 442.880534] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 443.292244] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 443.540364] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 443.797445] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 444.060424] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 444.286575] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 444.524546] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 444.769002] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 445.019277] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 445.276583] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 445.514443] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 445.760408] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 446.025272] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 446.300492] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 446.508475] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 446.760412] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 446.823475] uhci_hcd 0000:00:1d.0: host controller process error, something bad happened!
[ 446.823523] uhci_hcd 0000:00:1d.0: host controller process error, something bad happened!
[ 446.823526] uhci_hcd 0000:00:1d.0: host controller halted, very bad!
[ 446.823557] uhci_hcd 0000:00:1d.0: HC died; cleaning up
[ 447.124207] usb 1-1: new high-speed USB device number 14 using ehci_hcd
[ 447.268701] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 464.248194] usb 1-1: new high-speed USB device number 15 using ehci_hcd
[ 464.540485] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1903.153122] ipw2200: Firmware error detected. Restarting.
honza@honza-HP-Compaq-nc6120-PY507EA-AKB:~$
Akorát ten začátek chybí, nejde na něj vyrollovat
Ze začátku tam byl připojený disk WD, po chvíli koukání se odpojil. Pak to až nešlo, ani myš
-
Tak tohle je špatné, jádro postupně vyzkouší všechny ovládací moduly USB a každý selže. Normálně selhává jen ten vybraný, to se řeší tím, že tomu podstrčíš nějaký jiný, ale jak tomu podstrčit jiný, když selžou všechny.
Jaké máš v systému jádro uname -a
-
Já to pravidelně aktualizuji, takže tam bude asi to poslední (3.2.0.-47) ?
Omlouvám se, kdyby to byl nesmysl, beru to z hlavy ;)
-
Zadej ten příkaz výše do terminálu a výsledek dej sem, vypíše mi to verzi jádra i architekturu
-
uname -a
Linux honza-HP-Compaq-nc6120-PY507EA-AKB 3.2.0-49-generic-pae #75-Ubuntu SMP Tue Jun 18 18:00:21 UTC 2013 i686 i686 i386 GNU/Linux
-
Takže Ubuntu 12.04 32bit a jádro 3.2, pro tenhle systém najdeš v repozitáři backportované jádro 3.5, zkus si nainstalovat to
-
Link na nějaký návod ?
Děkuju
-
Link na nějaký návod ?
Děkuju
Naše wiki.
http://wiki.ubuntu.cz/aktualizace_kernelu (http://wiki.ubuntu.cz/aktualizace_kernelu)
-
sudo add-apt-repository ppa:upubuntu-com/kernel-i386
sudo apt-get update
sudo apt-get upgrade
Je to správně ?
Nejsem si jiste, tak se radši zeptám ???
-
Není nutný repozitář třetí strany, jen v Synaptiku vyhledej balíky linux-image-generic-lts-quantal a linux-headers-generic-lts-quantal ty označ k instalaci, zbytek potřebných změn to označí samo, nainstaluj a pak restartuj počítač a zkontroluj, že systém použil nové jádro.
-
Smím se zeptat, proč "lts-quantal" když já mám precise ?
jinak na ten update kernelu se vrhnu zítra, jsem tu jen na skok. Tak dám vědět, jak to dopadlo.
-
Protože je to jádro portované z 12.10 (Quantala), proto je takto označeno. Současné vydání 12.04.2 už ho má v základu, ale nižší instalace na něj automaticky nepřejdou (12.04 a 12.04.1)
-
Děkuju za vysvětlení :)
Večer to prubnu, pak dám vědět.
-
Tak uvidíme časem, jestli to bude dělat pořád.
Každopádně děkuju, máš u mě plus :D
EDIT: dopsal jsem ^^, a když jsem chtěl dát uspat do paměti, vypla se myš. Dělá to pořád..
Ale disk jede.. divný
[příloha smazaná administrátorem]
-
Otázka spíš je, vyřešil se původní problém s myší a diskem
-
těžko říct, kolikrát nefungovalo ani jedno usb.
teďka šel aspoň ten disk.. Je možný, že to teda shazuje ta myš ? (Lenovo)
-
Možné to je, asi bych zkusil jinou myš
-
Jenže ono to dělá jenom někdy, takže je to těžký "vysondovat".
Dám vědět, jak to pujde dál.
zatím děkuju ;)
-
Teď mi to nabídlo aktualizaci a míchá tam něco s kernelem 3.2, je možný že jsem nainstaloval tu 3.5 špatně ?
[příloha smazaná administrátorem]
-
Ne, jen ti zůstalo i jádro 3.2, použij Ubuntu Tweak a odstraň stará jádra
-
[ 1.790247] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.790295] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.790304] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.790323] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.790362] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002000
[ 1.790440] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.790448] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.790456] usb usb2: Product: UHCI Host Controller
[ 1.790463] usb usb2: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.790470] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.790778] hub 2-0:1.0: USB hub found
[ 1.790791] hub 2-0:1.0: 2 ports detected
[ 1.791001] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.791010] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.791024] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.791085] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00002020
[ 1.791163] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.791171] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.791179] usb usb3: Product: UHCI Host Controller
[ 1.791186] usb usb3: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.791193] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.791497] hub 3-0:1.0: USB hub found
[ 1.791509] hub 3-0:1.0: 2 ports detected
[ 1.791685] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.791695] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.791709] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.791772] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
[ 1.791846] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.791854] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.791861] usb usb4: Product: UHCI Host Controller
[ 1.791869] usb usb4: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.791876] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.792199] hub 4-0:1.0: USB hub found
[ 1.792211] hub 4-0:1.0: 2 ports detected
[ 1.792382] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.792391] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.792405] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.792470] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00002060
[ 1.792544] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.792552] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.792560] usb usb5: Product: UHCI Host Controller
[ 1.792567] usb usb5: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.792574] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.794235] uhci_hcd 0000:00:1d.1: host controller process error, something bad happened!
[ 1.794243] uhci_hcd 0000:00:1d.1: host controller halted, very bad!
[ 1.794264] uhci_hcd 0000:00:1d.1: HC died; cleaning up
[ 1.794770] uhci_hcd 0000:00:1d.2: host controller process error, something bad happened!
[ 1.794777] uhci_hcd 0000:00:1d.2: host controller halted, very bad!
[ 1.794798] uhci_hcd 0000:00:1d.2: HC died; cleaning up
[ 1.795525] uhci_hcd 0000:00:1d.3: host controller process error, something bad happened!
[ 1.795531] uhci_hcd 0000:00:1d.3: host controller halted, very bad!
[ 1.795551] uhci_hcd 0000:00:1d.3: HC died; cleaning up
[ 1.800931] uhci_hcd 0000:00:1d.0: host controller process error, something bad happened!
[ 1.800938] uhci_hcd 0000:00:1d.0: host controller halted, very bad!
[ 1.800958] uhci_hcd 0000:00:1d.0: HC died; cleaning up
[ 1.836471] usb usb5: can't set config #1, error -108
[ 1.836529] uhci_hcd 0000:00:1d.3: HC died; cleaning up
[ 1.836738] usbcore: registered new interface driver libusual
[ 1.836892] i8042: PNP: PS/2 Controller [PNP0303:C1C2,PNP0f13:C1C3] at 0x60,0x64 irq 1,12
[ 1.838649] i8042: Detected active multiplexing controller, rev 1.1
[ 1.839325] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.839339] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.882864] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.882938] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.883014] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.883314] mousedev: PS/2 mouse device common for all mice
[ 1.883712] rtc_cmos 00:08: RTC can wake from S4
[ 1.883961] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.884026] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.884171] device-mapper: uevent: version 1.0.3
[ 1.884346] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 1.884405] EISA: Probing bus 0 at eisa.0
[ 1.884418] Cannot allocate resource for EISA slot 1
[ 1.884423] Cannot allocate resource for EISA slot 2
[ 1.884428] Cannot allocate resource for EISA slot 3
[ 1.884434] Cannot allocate resource for EISA slot 4
[ 1.884452] Cannot allocate resource for EISA slot 7
[ 1.884463] EISA: Detected 0 cards.
[ 1.884563] cpuidle: using governor ladder
[ 1.884672] cpuidle: using governor menu
[ 1.884678] EFI Variables Facility v0.08 2004-May-17
[ 1.885129] ashmem: initialized
[ 1.885488] TCP: cubic registered
[ 1.885811] NET: Registered protocol family 10
[ 1.886355] NET: Registered protocol family 17
[ 1.886387] Key type dns_resolver registered
[ 1.886570] Using IPI No-Shortcut mode
[ 1.886806] PM: Hibernation image not present or could not be loaded.
[ 1.886835] registered taskstats version 1
[ 1.892369] Key type trusted registered
[ 1.897154] Key type encrypted registered
[ 1.903992] Magic number: 9:426:419
[ 1.904243] rtc_cmos 00:08: setting system clock to 2013-08-04 07:24:01 UTC (1375601041)
[ 1.908236] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.952581] isapnp: No Plug & Play device found
[ 1.953025] ata1.00: ATA-6: ST9808211A, 3.02, max UDMA/100
[ 1.953033] ata1.00: 156301488 sectors, multi 16: LBA48
[ 1.953048] ata1.01: ATAPI: HL-DT-ST DVD-RW GWA-4082N, CC15, max MWDMA2
[ 1.959577] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.959579] EDD information not available.
[ 1.968384] ata1.00: configured for UDMA/100
[ 1.984240] ata1.01: configured for MWDMA2
[ 1.986858] scsi 0:0:0:0: Direct-Access ATA ST9808211A 3.02 PQ: 0 ANSI: 5
[ 1.987064] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.987128] sd 0:0:0:0: [sda] Write Protect is off
[ 1.987132] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.987160] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.987523] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.990098] ACPI: Battery Slot [C174] (battery present)
[ 2.105984] sda: sda1 sda2 < sda5 >
[ 2.106331] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.110467] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-RW GWA-4082N CC15 PQ: 0 ANSI: 5
[ 2.115792] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 2.115795] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.115912] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 2.116070] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 2.116167] Freeing unused kernel memory: 760k freed
[ 2.116556] Write protecting the kernel text: 6056k
[ 2.116578] Write protecting the kernel read-only data: 2480k
[ 2.116580] NX-protecting the kernel data: 4184k
[ 2.134903] udevd[92]: starting version 175
[ 2.362452] tg3.c:v3.123 (March 21, 2012)
[ 2.364176] sdhci: Secure Digital Host Controller Interface driver
[ 2.364179] sdhci: Copyright(c) Pierre Ossman
[ 2.453300] tg3 0000:02:0e.0: eth0: Tigon3 [partno(BCM95705A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:14:c2:dd:ce:3c
[ 2.453309] tg3 0000:02:0e.0: eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0])
[ 2.453313] tg3 0000:02:0e.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 2.453316] tg3 0000:02:0e.0: eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
[ 2.453397] sdhci-pci 0000:02:06.4: SDHCI controller found [104c:8034] (rev 0)
[ 2.453488] mmc0: no vmmc regulator found
[ 2.453523] Registered led device: mmc0::
[ 2.491139] mmc0: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 2.491182] mmc1: no vmmc regulator found
[ 2.491224] Registered led device: mmc1::
[ 2.520035] mmc1: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 2.520058] mmc2: no vmmc regulator found
[ 2.520089] Registered led device: mmc2::
[ 2.556037] mmc2: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 2.612105] firewire_ohci 0000:02:06.2: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
[ 2.729306] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.112157] firewire_core 0000:02:06.2: created device fw0: GUID 718b500029314ca6, S400
[ 21.138321] Adding 1562620k swap on /dev/sda5. Priority:-1 extents:1 across:1562620k
[ 21.152329] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.201129] udevd[334]: starting version 175
[ 21.276477] lp: driver loaded but no devices found
[ 21.329128] ACPI: Video Device [C055] (multi-head: yes rom: no post: no)
[ 21.357359] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 21.435454] [drm] Initialized drm 1.1.0 20060810
[ 21.473712] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 21.551278] wmi: Mapper loaded
[ 21.760220] intel_rng: FWH not detected
[ 21.762003] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:099c]
[ 21.762028] yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
[ 21.762035] yenta_cardbus 0000:02:06.0: Using INTVAL to route CSC interrupts to PCI
[ 21.762038] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
[ 21.762045] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01aa1b22, devctl 0x64
[ 21.768340] lib80211: common routines for IEEE802.11 drivers
[ 21.768345] lib80211_crypt: registered algorithm 'NULL'
[ 21.770641] i915 0000:00:02.0: setting latency timer to 64
[ 21.775025] ppdev: user-space parallel port driver
[ 21.782496] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 21.782500] [drm] Driver supports precise vblank timestamp query.
[ 21.882822] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 21.992948] Bluetooth: Core ver 2.16
[ 21.992978] NET: Registered protocol family 31
[ 21.992981] Bluetooth: HCI device and connection manager initialized
[ 21.992983] Bluetooth: HCI socket layer initialized
[ 21.992985] Bluetooth: L2CAP socket layer initialized
[ 21.992996] Bluetooth: SCO socket layer initialized
[ 21.993874] parport_pc 00:04: reported by Plug and Play ACPI
[ 21.993954] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 21.996722] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0c78, PCI irq 18
[ 21.996727] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 21.996737] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
[ 21.996741] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x4fff:
[ 22.008679] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.008684] Bluetooth: BNEP filters: protocol multicast
[ 22.009736] libipw: 802.11 data/management/control stack, git-1.1.13
[ 22.009739] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 22.013543] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 22.013548] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 22.016219] cfg80211: Calling CRDA to update world regulatory domain
[ 22.000898] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff 0x4c00-0x4cff
[ 22.057672] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd03fffff]
[ 22.057680] pcmcia_socket pcmcia_socket0: cs: memory probe 0xd0000000-0xd03fffff:
[ 22.057684] excluding 0xd0000000-0xd003ffff
[ 22.057701] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x60000000-0x67ffffff pref]
[ 22.057705] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x67ffffff:
[ 22.057719] excluding 0x60000000-0x67ffffff
[ 22.080308] irda_init()
[ 22.080327] NET: Registered protocol family 23
[ 22.084246] Bluetooth: RFCOMM TTY layer initialized
[ 22.084252] Bluetooth: RFCOMM socket layer initialized
[ 22.084254] Bluetooth: RFCOMM ver 1.11
[ 22.095303] found SMC SuperIO Chip (devid=0x7a rev=00 base=0x004e): LPC47N227
[ 22.095328] smsc_superio_flat(): fir: 0x100, sir: 0x3e8, dma: 03, irq: 3, mode: 0x0e
[ 22.095334] smsc_ircc_present: can't get sir_base of 0x3e8
[ 22.099178] lp0: using parport0 (interrupt-driven).
[ 22.104804] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 22.117973] type=1400 audit(1375601061.709:2): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=633 comm="apparmor_parser"
[ 22.123047] type=1400 audit(1375601061.713:3): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=633 comm="apparmor_parser"
[ 22.162200] type=1400 audit(1375601061.753:4): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=642 comm="apparmor_parser"
[ 22.170024] type=1400 audit(1375601061.761:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser"
[ 22.170356] type=1400 audit(1375601061.761:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser"
[ 22.292000] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
[ 22.358894] [drm] initialized overlay support
[ 22.602715] init: failsafe main process (710) killed by TERM signal
[ 22.834767] type=1400 audit(1375601062.425:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=806 comm="apparmor_parser"
[ 22.835257] type=1400 audit(1375601062.425:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=806 comm="apparmor_parser"
[ 22.857186] type=1400 audit(1375601062.449:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=808 comm="apparmor_parser"
[ 22.860630] type=1400 audit(1375601062.453:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=808 comm="apparmor_parser"
[ 22.860971] type=1400 audit(1375601062.453:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=808 comm="apparmor_parser"
[ 22.884512] psmouse serio4: synaptics: Touchpad model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000/0x0
[ 22.884523] psmouse serio4: synaptics: serio: Synaptics pass-through port at isa0060/serio4/input0
[ 23.001099] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input5
[ 23.057028] fbcon: inteldrmfb (fb0) is primary device
[ 23.058343] Console: switching to colour frame buffer device 128x48
[ 23.058383] fb0: inteldrmfb frame buffer device
[ 23.058386] drm: registered panic notifier
[ 23.058398] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 23.065192] ACPI Warning: 0x00001060-0x0000107f SystemIO conflicts with Region \_SB_.C002.C003.C08F 1 (20120320/utaddress-251)
[ 23.065204] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 23.065207] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
[ 23.065212] ACPI Warning: 0x00001028-0x0000102f SystemIO conflicts with Region \_SB_.C002.C003.C086 1 (20120320/utaddress-251)
[ 23.065217] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 23.065221] ACPI Warning: 0x00001100-0x0000113f SystemIO conflicts with Region \_SB_.C002.C003.C097 1 (20120320/utaddress-251)
[ 23.065226] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 23.065229] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 23.066286] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 23.199573] cfg80211: World regulatory domain updated:
[ 23.199580] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 23.199583] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.199586] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.199588] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.199591] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.199593] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.214453] input: HP WMI hotkeys as /devices/virtual/input/input6
[ 23.564310] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.568281] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.576193] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 23.776732] ipw2200: Radio Frequency Kill Switch is On:
[ 23.776732] Kill switch must be turned off for wireless networking to work.
[ 23.806082] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806088] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806091] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806094] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806096] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806099] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806101] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806104] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806107] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806109] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806112] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806114] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806117] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806120] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806122] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806125] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806127] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806130] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806132] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806135] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806137] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806140] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.806143] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806145] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.806148] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806151] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.806153] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 23.806156] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.810731] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
[ 23.810918] yenta_cardbus 0000:02:06.1: CardBus bridge found [103c:099c]
[ 23.810945] yenta_cardbus 0000:02:06.1: Using CSCINT to route CSC interrupts to PCI
[ 23.810948] yenta_cardbus 0000:02:06.1: Routing CardBus interrupts to PCI
[ 23.810955] yenta_cardbus 0000:02:06.1: TI: mfunc 0x01aa1b22, devctl 0x64
[ 23.861051] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.052870] yenta_cardbus 0000:02:06.1: ISA IRQ mask 0x0c78, PCI irq 19
[ 24.052878] yenta_cardbus 0000:02:06.1: Socket status: 30000006
[ 24.052883] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #04 to #07
[ 24.052895] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
[ 24.052900] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x4000-0x4fff:
[ 24.054191] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff 0x4c00-0x4cff
[ 24.062279] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd03fffff]
[ 24.062283] pcmcia_socket pcmcia_socket1: cs: memory probe 0xd0000000-0xd03fffff:
[ 24.062288] excluding 0xd0000000-0xd003ffff
[ 24.062304] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [mem 0x60000000-0x67ffffff pref]
[ 24.062308] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x67ffffff:
[ 24.062322] excluding 0x60000000-0x67ffffff
[ 24.119158] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[ 24.120492] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 24.121214] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[ 24.121556] excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 24.121893] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[ 24.122467] clean.
[ 24.122485] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[ 24.123121] clean.
[ 24.123141] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[ 24.123146] excluding 0xc0000-0xc7fff 0xe0000-0xfffff
[ 24.123176] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[ 24.123193] clean.
[ 24.123210] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[ 24.123224] excluding 0x60000000-0x60ffffff
[ 24.123243] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[ 24.123900] clean.
[ 24.128277] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af:
[ 24.129256] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 24.129973] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff:
[ 24.130313] excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 24.130651] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff:
[ 24.131226] clean.
[ 24.131243] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7:
[ 24.131879] clean.
[ 24.131898] pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0fffff:
[ 24.131902] excluding 0xc0000-0xc7fff 0xe0000-0xfffff
[ 24.131931] pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff:
[ 24.131948] clean.
[ 24.131965] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff:
[ 24.131979] excluding 0x60000000-0x60ffffff
[ 24.156842] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff:
[ 24.157509] clean.
[ 24.244040] intel8x0_measure_ac97_clock: measured 55433 usecs (2671 samples)
[ 24.244047] intel8x0: clocking to 48000
[ 25.031956] init: anacron main process (965) killed by TERM signal
[ 26.096028] ipw2200: Failed to send POWER_MODE: Command timed out.
[ 31.688053] ipw2200: Failed to send POWER_MODE: Command timed out.
[ 104.772074] usb 1-1: new high-speed USB device number 3 using ehci_hcd
[ 104.915108] usb 1-1: device descriptor read/all, error -71
[ 105.028076] usb 1-1: new high-speed USB device number 4 using ehci_hcd
[ 105.174850] usb 1-1: unable to read config index 0 descriptor/all
[ 105.174860] usb 1-1: can't read configurations, error -71
[ 105.288065] usb 1-1: new high-speed USB device number 5 using ehci_hcd
[ 105.325390] usb 1-1: unable to read config index 0 descriptor/all
[ 105.325399] usb 1-1: can't read configurations, error -71
[ 105.440060] usb 1-1: new high-speed USB device number 6 using ehci_hcd
[ 105.470936] usb 1-1: device descriptor read/8, error -71
[ 105.599101] usb 1-1: device descriptor read/8, error -71
[ 105.700071] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 112.636039] usb 1-1: new high-speed USB device number 7 using ehci_hcd
[ 112.785975] usb 1-1: unable to read config index 0 descriptor/all
[ 112.785984] usb 1-1: can't read configurations, error -71
[ 112.900041] usb 1-1: new high-speed USB device number 8 using ehci_hcd
[ 113.042764] usb 1-1: device descriptor read/all, error -71
[ 113.156024] usb 1-1: new high-speed USB device number 9 using ehci_hcd
[ 113.186707] usb 1-1: device descriptor read/8, error -71
[ 113.314776] usb 1-1: device descriptor read/8, error -71
[ 113.528053] usb 1-1: new high-speed USB device number 10 using ehci_hcd
[ 113.558759] usb 1-1: device descriptor read/8, error -71
[ 113.687212] usb 1-1: device descriptor read/8, error -71
[ 113.788066] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 120.716215] usb 1-1: new high-speed USB device number 11 using ehci_hcd
[ 120.862845] usb 1-1: device descriptor read/all, error -71
[ 120.976066] usb 1-1: new high-speed USB device number 12 using ehci_hcd
[ 121.122821] usb 1-1: device descriptor read/all, error -71
[ 121.236225] usb 1-1: new high-speed USB device number 13 using ehci_hcd
[ 121.280534] usb 1-1: unable to read config index 0 descriptor/all
[ 121.280545] usb 1-1: can't read configurations, error -71
[ 121.396195] usb 1-1: new high-speed USB device number 14 using ehci_hcd
[ 121.436588] usb 1-1: unable to read config index 0 descriptor/all
[ 121.436597] usb 1-1: can't read configurations, error -71
[ 121.440227] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 223.504205] usb 1-2: new high-speed USB device number 17 using ehci_hcd
[ 223.646906] usb 1-2: device descriptor read/all, error -71
[ 223.760201] usb 1-2: new high-speed USB device number 18 using ehci_hcd
[ 223.902856] usb 1-2: device descriptor read/all, error -71
[ 224.016196] usb 1-2: new high-speed USB device number 19 using ehci_hcd
[ 224.046776] usb 1-2: device descriptor read/8, error -71
[ 224.174936] usb 1-2: device descriptor read/8, error -71
[ 224.388201] usb 1-2: new high-speed USB device number 20 using ehci_hcd
[ 224.424696] usb 1-2: unable to read config index 0 descriptor/all
[ 224.424705] usb 1-2: can't read configurations, error -71
[ 224.428046] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 231.480241] usb 1-2: new high-speed USB device number 21 using ehci_hcd
[ 231.631595] usb 1-2: unable to read config index 0 descriptor/all
[ 231.631609] usb 1-2: can't read configurations, error -71
[ 231.744212] usb 1-2: new high-speed USB device number 22 using ehci_hcd
[ 231.890893] usb 1-2: device descriptor read/all, error -71
[ 232.004198] usb 1-2: new high-speed USB device number 23 using ehci_hcd
[ 232.055612] usb 1-2: unable to read config index 0 descriptor/all
[ 232.055622] usb 1-2: can't read configurations, error -71
[ 232.168196] usb 1-2: new high-speed USB device number 24 using ehci_hcd
[ 232.205184] usb 1-2: unable to read config index 0 descriptor/all
[ 232.205194] usb 1-2: can't read configurations, error -71
[ 232.208190] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 239.140111] usb 1-2: new high-speed USB device number 25 using ehci_hcd
[ 239.287000] usb 1-2: device descriptor read/all, error -71
[ 239.400092] usb 1-2: new high-speed USB device number 26 using ehci_hcd
[ 239.552486] usb 1-2: unable to read config index 0 descriptor/all
[ 239.552503] usb 1-2: can't read configurations, error -75
[ 239.668059] usb 1-2: new high-speed USB device number 27 using ehci_hcd
[ 239.698908] usb 1-2: device descriptor read/8, error -71
[ 239.827118] usb 1-2: device descriptor read/8, error -71
[ 240.040199] usb 1-2: new high-speed USB device number 28 using ehci_hcd
[ 240.078859] usb 1-2: unable to read config index 0 descriptor/all
[ 240.078869] usb 1-2: can't read configurations, error -71
[ 240.080188] hub 1-0:1.0: unable to enumerate USB device on port 2
Přes víkend jsem byl připojenej přes mobil a dneska ráno přestala zase fungovat myš, telefon co byl přes USB připojen tak mě odpojil. Tak jsem to opět všechno odpojil/zapojil, myš se nechytla a telefon mi jen nabídl jestli chci flash/pc suite a pak stejně nic.. (měl se nabíjet a připojit mě).
Jinou myš jsem zkusil, ale nechytala se. (bezdrátová)
Teď jsem dorazil domu, píšu sem a zase nejde :D
-
[ 0.342833] ACPI: AC Adapter [C172] (on-line)
[ 0.342941] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 0.342950] ACPI: Sleep Button [C1E8]
[ 0.343011] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 0.343056] ACPI: Lid Switch [C1E9]
[ 0.343120] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.343124] ACPI: Power Button [PWRF]
[ 0.343247] ACPI: Fan [C248] (off)
[ 0.343321] ACPI: Fan [C249] (off)
[ 0.343396] ACPI: Fan [C24A] (off)
[ 0.343463] ACPI: Fan [C24B] (off)
[ 0.343522] ACPI: Requesting acpi_cpufreq
[ 0.701654] Freeing initrd memory: 15192k freed
[ 0.716917] Marking TSC unstable due to TSC halts in idle
[ 0.716939] ACPI: acpi_idle registered with cpuidle
[ 0.740263] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.740269] ACPI: Thermal Zone [TZ1] (44 C)
[ 0.754249] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.754252] ACPI: Thermal Zone [TZ2] (29 C)
[ 0.763666] thermal LNXTHERM:02: registered as thermal_zone2
[ 0.763669] ACPI: Thermal Zone [TZ3] (29 C)
[ 0.767407] thermal LNXTHERM:03: registered as thermal_zone3
[ 0.767410] ACPI: Thermal Zone [TZ4] (66 C)
[ 0.767444] ACPI: Battery Slot [C174] (battery present)
[ 0.767731] ACPI: Battery Slot [C173] (battery absent)
[ 0.767804] GHES: HEST is not enabled!
[ 0.767940] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.788508] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.788613] ACPI: Battery Slot [C173] (battery absent)
[ 0.788633] isapnp: Scanning for PnP cards...
[ 0.901946] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[ 0.923688] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.011298] Linux agpgart interface v0.103
[ 1.011378] agpgart-intel 0000:00:00.0: Intel 915GM Chipset
[ 1.011444] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[ 1.012372] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 1.012531] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 1.014478] brd: module loaded
[ 1.015491] loop: module loaded
[ 1.015665] ata_piix 0000:00:1f.1: version 2.13
[ 1.015729] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.016144] scsi0 : ata_piix
[ 1.016229] scsi1 : ata_piix
[ 1.016751] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x2580 irq 14
[ 1.016754] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x2588 irq 15
[ 1.017218] Fixed MDIO Bus: probed
[ 1.017289] tun: Universal TUN/TAP device driver, 1.6
[ 1.017291] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.017340] PPP generic driver version 2.4.2
[ 1.017400] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.017444] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.017449] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.017457] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.017491] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.021384] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 1.021568] ata2: port disabled--ignoring
[ 1.021599] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0580000
[ 1.065447] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.065522] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.065526] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.065529] usb usb1: Product: EHCI Host Controller
[ 1.065532] usb usb1: Manufacturer: Linux 3.5.0-37-generic ehci_hcd
[ 1.065535] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.065692] hub 1-0:1.0: USB hub found
[ 1.065699] hub 1-0:1.0: 8 ports detected
[ 1.065806] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.065837] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.065861] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.065866] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.065875] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.065901] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002000
[ 1.065939] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.065943] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.065946] usb usb2: Product: UHCI Host Controller
[ 1.065949] usb usb2: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.065952] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.066088] hub 2-0:1.0: USB hub found
[ 1.066094] hub 2-0:1.0: 2 ports detected
[ 1.066176] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.066181] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.066187] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.066226] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00002020
[ 1.066264] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.066267] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.066270] usb usb3: Product: UHCI Host Controller
[ 1.066274] usb usb3: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.066277] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.066411] hub 3-0:1.0: USB hub found
[ 1.066416] hub 3-0:1.0: 2 ports detected
[ 1.066500] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.066505] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.066512] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.066550] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
[ 1.066587] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.066590] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.066594] usb usb4: Product: UHCI Host Controller
[ 1.066597] usb usb4: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.066600] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.066762] hub 4-0:1.0: USB hub found
[ 1.066767] hub 4-0:1.0: 2 ports detected
[ 1.066849] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.066854] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.066860] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.066900] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00002060
[ 1.066938] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.066942] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.066945] usb usb5: Product: UHCI Host Controller
[ 1.066948] usb usb5: Manufacturer: Linux 3.5.0-37-generic uhci_hcd
[ 1.066951] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.067088] hub 5-0:1.0: USB hub found
[ 1.067094] hub 5-0:1.0: 2 ports detected
[ 1.067242] usbcore: registered new interface driver libusual
[ 1.067314] i8042: PNP: PS/2 Controller [PNP0303:C1C2,PNP0f13:C1C3] at 0x60,0x64 irq 1,12
[ 1.068926] i8042: Detected active multiplexing controller, rev 1.1
[ 1.069631] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.069638] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.113270] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.113302] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.113332] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.113470] mousedev: PS/2 mouse device common for all mice
[ 1.113656] rtc_cmos 00:08: RTC can wake from S4
[ 1.113811] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.113846] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.113913] device-mapper: uevent: version 1.0.3
[ 1.113994] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 1.114018] EISA: Probing bus 0 at eisa.0
[ 1.114025] Cannot allocate resource for EISA slot 1
[ 1.114028] Cannot allocate resource for EISA slot 2
[ 1.114030] Cannot allocate resource for EISA slot 3
[ 1.114032] Cannot allocate resource for EISA slot 4
[ 1.114043] Cannot allocate resource for EISA slot 7
[ 1.114049] EISA: Detected 0 cards.
[ 1.114095] cpuidle: using governor ladder
[ 1.114134] cpuidle: using governor menu
[ 1.114137] EFI Variables Facility v0.08 2004-May-17
[ 1.114342] ashmem: initialized
[ 1.114512] TCP: cubic registered
[ 1.114655] NET: Registered protocol family 10
[ 1.114903] NET: Registered protocol family 17
[ 1.114917] Key type dns_resolver registered
[ 1.115007] Using IPI No-Shortcut mode
[ 1.115114] PM: Hibernation image not present or could not be loaded.
[ 1.115132] registered taskstats version 1
[ 1.117808] Key type trusted registered
[ 1.119869] Key type encrypted registered
[ 1.122351] Magic number: 9:566:699
[ 1.122507] rtc_cmos 00:08: setting system clock to 2013-08-04 20:40:31 UTC (1375648831)
[ 1.126748] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.126751] EDD information not available.
[ 1.214515] isapnp: No Plug & Play device found
[ 1.215324] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.228400] ata1.00: ATA-6: ST9808211A, 3.02, max UDMA/100
[ 1.228404] ata1.00: 156301488 sectors, multi 16: LBA48
[ 1.228411] ata1.01: ATAPI: HL-DT-ST DVD-RW GWA-4082N, CC15, max MWDMA2
[ 1.243778] ACPI: Battery Slot [C174] (battery present)
[ 1.244277] ata1.00: configured for UDMA/100
[ 1.260281] ata1.01: configured for MWDMA2
[ 1.262744] scsi 0:0:0:0: Direct-Access ATA ST9808211A 3.02 PQ: 0 ANSI: 5
[ 1.262923] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.263025] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.263084] sd 0:0:0:0: [sda] Write Protect is off
[ 1.263088] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.263114] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.316082] sda: sda1 sda2 < sda5 >
[ 1.316418] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.320435] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-RW GWA-4082N CC15 PQ: 0 ANSI: 5
[ 1.325541] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 1.325544] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.325665] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 1.325791] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 1.325901] Freeing unused kernel memory: 760k freed
[ 1.326295] Write protecting the kernel text: 6056k
[ 1.326317] Write protecting the kernel read-only data: 2480k
[ 1.326319] NX-protecting the kernel data: 4184k
[ 1.344815] udevd[90]: starting version 175
[ 1.564072] usb 2-2: new low-speed USB device number 2 using uhci_hcd
[ 1.573982] sdhci: Secure Digital Host Controller Interface driver
[ 1.573986] sdhci: Copyright(c) Pierre Ossman
[ 1.574313] sdhci-pci 0000:02:06.4: SDHCI controller found [104c:8034] (rev 0)
[ 1.574405] mmc0: no vmmc regulator found
[ 1.574443] Registered led device: mmc0::
[ 1.611109] mmc0: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.611163] mmc1: no vmmc regulator found
[ 1.611208] Registered led device: mmc1::
[ 1.640100] mmc1: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.640150] mmc2: no vmmc regulator found
[ 1.640199] Registered led device: mmc2::
[ 1.672021] mmc2: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.672198] tg3.c:v3.123 (March 21, 2012)
[ 1.753656] tg3 0000:02:0e.0: eth0: Tigon3 [partno(BCM95705A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:14:c2:dd:ce:3c
[ 1.753664] tg3 0000:02:0e.0: eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0])
[ 1.753668] tg3 0000:02:0e.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.753671] tg3 0000:02:0e.0: eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
[ 1.777064] usb 2-2: New USB device found, idVendor=04b3, idProduct=310c
[ 1.777069] usb 2-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1.777073] usb 2-2: Product: USB Optical Mouse
[ 1.808904] firewire_ohci 0000:02:06.2: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
[ 1.847208] usbcore: registered new interface driver usbhid
[ 1.847212] usbhid: USB HID core driver
[ 1.851318] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input4
[ 1.851566] hid-generic 0003:04B3:310C.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.0-2/input0
[ 1.970376] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.308157] firewire_core 0000:02:06.2: created device fw0: GUID 718b500029314ca6, S400
[ 20.448089] Adding 1562620k swap on /dev/sda5. Priority:-1 extents:1 across:1562620k
[ 20.460336] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.501671] udevd[341]: starting version 175
[ 20.589544] lp: driver loaded but no devices found
[ 20.639186] ACPI: Video Device [C055] (multi-head: yes rom: no post: no)
[ 20.667550] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 20.701504] [drm] Initialized drm 1.1.0 20060810
[ 20.825523] wmi: Mapper loaded
[ 20.827480] lib80211: common routines for IEEE802.11 drivers
[ 20.827485] lib80211_crypt: registered algorithm 'NULL'
[ 20.880989] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:099c]
[ 20.881016] yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
[ 20.881023] yenta_cardbus 0000:02:06.0: Using INTVAL to route CSC interrupts to PCI
[ 20.881026] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
[ 20.881034] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01aa1b22, devctl 0x64
[ 20.924177] i915 0000:00:02.0: setting latency timer to 64
[ 20.925515] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 20.925520] [drm] Driver supports precise vblank timestamp query.
[ 20.962818] cfg80211: Calling CRDA to update world regulatory domain
[ 20.965946] libipw: 802.11 data/management/control stack, git-1.1.13
[ 20.965951] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 20.983619] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.986184] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 20.986188] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 20.994363] intel_rng: FWH not detected
[ 21.016072] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 21.108553] parport_pc 00:04: reported by Plug and Play ACPI
[ 21.108635] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 21.112969] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0c78, PCI irq 18
[ 21.112975] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 21.112984] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
[ 21.112989] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x4fff:
[ 21.170208] irda_init()
[ 21.170228] NET: Registered protocol family 23
[ 21.170976] found SMC SuperIO Chip (devid=0x7a rev=00 base=0x004e): LPC47N227
[ 21.170998] smsc_superio_flat(): fir: 0x100, sir: 0x3e8, dma: 03, irq: 3, mode: 0x0e
[ 21.171004] smsc_ircc_present: can't get sir_base of 0x3e8
[ 21.114566] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff 0x4c00-0x4cff
[ 21.185079] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd03fffff]
[ 21.185086] pcmcia_socket pcmcia_socket0: cs: memory probe 0xd0000000-0xd03fffff:
[ 21.185091] excluding 0xd0000000-0xd003ffff
[ 21.185107] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x60000000-0x67ffffff pref]
[ 21.185111] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x67ffffff:
[ 21.185125] excluding 0x60000000-0x67ffffff
[ 21.199968] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 21.213959] lp0: using parport0 (interrupt-driven).
[ 21.311405] Bluetooth: Core ver 2.16
[ 21.312557] NET: Registered protocol family 31
[ 21.312561] Bluetooth: HCI device and connection manager initialized
[ 21.312563] Bluetooth: HCI socket layer initialized
[ 21.312565] Bluetooth: L2CAP socket layer initialized
[ 21.312571] Bluetooth: SCO socket layer initialized
[ 21.313415] ppdev: user-space parallel port driver
[ 21.338105] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 21.338111] Bluetooth: BNEP filters: protocol multicast
[ 21.355858] Bluetooth: RFCOMM TTY layer initialized
[ 21.355867] Bluetooth: RFCOMM socket layer initialized
[ 21.355869] Bluetooth: RFCOMM ver 1.11
[ 21.416173] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
[ 21.443329] [drm] initialized overlay support
[ 21.465158] type=1400 audit(1375648851.837:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=671 comm="apparmor_parser"
[ 21.465754] type=1400 audit(1375648851.837:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=671 comm="apparmor_parser"
[ 21.466089] type=1400 audit(1375648851.837:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=671 comm="apparmor_parser"
[ 21.483550] type=1400 audit(1375648851.853:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=679 comm="apparmor_parser"
[ 21.488737] type=1400 audit(1375648851.861:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=679 comm="apparmor_parser"
[ 21.963568] psmouse serio4: synaptics: Touchpad model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000/0x0
[ 21.963580] psmouse serio4: synaptics: serio: Synaptics pass-through port at isa0060/serio4/input0
[ 21.982115] init: failsafe main process (724) killed by TERM signal
[ 22.008141] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input6
[ 22.226333] fbcon: inteldrmfb (fb0) is primary device
[ 22.236160] Console: switching to colour frame buffer device 128x48
[ 22.236203] fb0: inteldrmfb frame buffer device
[ 22.236206] drm: registered panic notifier
[ 22.236222] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 22.241138] ACPI Warning: 0x00001060-0x0000107f SystemIO conflicts with Region \_SB_.C002.C003.C08F 1 (20120320/utaddress-251)
[ 22.241148] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 22.241151] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
[ 22.241155] ACPI Warning: 0x00001028-0x0000102f SystemIO conflicts with Region \_SB_.C002.C003.C086 1 (20120320/utaddress-251)
[ 22.241161] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 22.241165] ACPI Warning: 0x00001100-0x0000113f SystemIO conflicts with Region \_SB_.C002.C003.C097 1 (20120320/utaddress-251)
[ 22.241170] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 22.241172] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 22.242049] type=1400 audit(1375648852.613:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=829 comm="apparmor_parser"
[ 22.242532] type=1400 audit(1375648852.613:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=829 comm="apparmor_parser"
[ 22.243114] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 22.254703] type=1400 audit(1375648852.625:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=832 comm="apparmor_parser"
[ 22.256777] type=1400 audit(1375648852.629:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=832 comm="apparmor_parser"
[ 22.257116] type=1400 audit(1375648852.629:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=832 comm="apparmor_parser"
[ 22.442407] cfg80211: World regulatory domain updated:
[ 22.442413] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 22.442416] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 22.442419] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 22.442422] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 22.442425] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 22.442427] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 22.552135] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 22.935895] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 22.939946] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.940780] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.084623] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084629] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084632] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084635] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084637] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084640] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084642] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084645] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084647] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084650] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084653] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084655] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084658] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084661] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084663] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084666] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084668] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084682] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084685] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084688] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084690] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084693] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 23.084695] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084698] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.084701] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084703] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.084706] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 23.084709] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 23.149128] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
[ 23.150532] yenta_cardbus 0000:02:06.1: CardBus bridge found [103c:099c]
[ 23.150560] yenta_cardbus 0000:02:06.1: Using CSCINT to route CSC interrupts to PCI
[ 23.150563] yenta_cardbus 0000:02:06.1: Routing CardBus interrupts to PCI
[ 23.150570] yenta_cardbus 0000:02:06.1: TI: mfunc 0x01aa1b22, devctl 0x64
[ 23.384738] yenta_cardbus 0000:02:06.1: ISA IRQ mask 0x0c78, PCI irq 19
[ 23.384746] yenta_cardbus 0000:02:06.1: Socket status: 30000006
[ 23.384751] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #04 to #07
[ 23.384764] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
[ 23.384769] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x4000-0x4fff:
[ 23.386060] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff 0x4c00-0x4cff
[ 23.390412] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd03fffff]
[ 23.390416] pcmcia_socket pcmcia_socket1: cs: memory probe 0xd0000000-0xd03fffff:
[ 23.390421] excluding 0xd0000000-0xd003ffff
[ 23.390437] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [mem 0x60000000-0x67ffffff pref]
[ 23.390441] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x67ffffff:
[ 23.390454] excluding 0x60000000-0x67ffffff
[ 23.418698] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[ 23.419701] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 23.420765] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[ 23.421107] excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 23.421445] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[ 23.422018] clean.
[ 23.422036] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[ 23.422689] clean.
[ 23.422712] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[ 23.422716] excluding 0xc0000-0xc7fff 0xe0000-0xfffff
[ 23.422745] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[ 23.422763] clean.
[ 23.422780] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[ 23.422794] excluding 0x60000000-0x60ffffff
[ 23.422813] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[ 23.423468] clean.
[ 23.430752] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af:
[ 23.431739] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 23.432787] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff:
[ 23.433130] excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 23.433467] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff:
[ 23.434040] clean.
[ 23.434058] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7:
[ 23.434691] clean.
[ 23.434712] pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0fffff:
[ 23.434717] excluding 0xc0000-0xc7fff 0xe0000-0xfffff
[ 23.434746] pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff:
[ 23.434763] clean.
[ 23.434780] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff:
[ 23.434794] excluding 0x60000000-0x60ffffff
[ 23.434813] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff:
[ 23.435468] clean.
[ 23.524043] intel8x0_measure_ac97_clock: measured 55419 usecs (2670 samples)
[ 23.524049] intel8x0: clocking to 48000
[ 24.209565] lib80211_crypt: registered algorithm 'TKIP'
[ 338.196129] uhci_hcd 0000:00:1d.0: host controller process error, something bad happened!
[ 338.196142] uhci_hcd 0000:00:1d.0: host controller halted, very bad!
[ 338.196167] uhci_hcd 0000:00:1d.0: HC died; cleaning up
[ 338.196200] usb 2-2: USB disconnect, device number 2
[ 354.449440] audit_printk_skb: 39 callbacks suppressed
[ 354.449451] type=1400 audit(1375649183.865:25): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=685 comm="cupsd" pid=685 comm="cupsd" capability=36 capname="block_suspend"
honza@honza-HP-Compaq-nc6120-PY507EA-AKB:~$
Opět stejný scénář, po chvíli se vypla myš
-
Teď už to nepadá, ale objevuje se tam host controler halted, což v kostce znamená, že ten počítač deaktivuje řadič USB.
Zkus si vypnout uspávání řadiče, návod je tady http://askubuntu.com/questions/141832/usb-mouse-sleeping-after-5-seconds-when-on-battery
-
Chtěl jsem to udělat podle toho prvního příspěvku pod tím a poprvé mi vyskočilo :
honza@honza-HP-Compaq-nc6120-PY507EA-AKB:~$ sudo gedit /etc/laptop-mode/conf.d/usb-autosuspend.conf
[sudo] password for honza:
(gedit:2589): Gtk-WARNING **: Attempting to store changes into `/root/.local/share/recently-used.xbel', but failed: Nelze vytvořit soubor „/root/.local/share/recently-used.xbel.9EMZ0W“: Adresář nebo soubor neexistuje
(gedit:2589): Gtk-WARNING **: Attempting to set the permissions of `/root/.local/share/recently-used.xbel', but failed: Adresář nebo soubor neexistuje
(gedit:2589): GLib-GIO-WARNING **: Missing callback called fullpath = /root/.local/share/recently-used.xbel
A když jsem to dělal po druhé, tak je to jen prázdnej dokument.
Já totiž v etc ani folder laptop-mode nemám
[příloha smazaná administrátorem]
-
Zkusíme něco lehčího, vypnout správu napájení pro USB není tak jednoduché jak se zdá.
Zkus si jen do GRUBu přidat parametr acpi_osi=Linux
-
Pro mě neprobádané vody, je to správně ?
GRUB_DEFAULT=0
GRUB_HIDDEN_TIMEOUT=0
GRUB_HIDDEN_TIMEOUT_QUIET=true
GRUB_TIMEOUT=10
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX="acpi_osi=Linux"
-
Technicky ano, ale lepší je to přidat o řádek výš, tedy tohle
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" upravit na tohle GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=Linux" z toho řádku pod tím to můžeš vymazat. Nezapomenout po uložení udělat update GRUBu sudo update-grub
-
A potom zkusit opět ten návod z toho linku ?
-
To ne, ty návody jsou staré, balík laptop-mode se už v základu nepoužívá
-
No každopádně ten parametr jsem už do grubu přidal, jaký je další postup ?
-
Nic, počkat jestli to znovu spadne
-
Tak já už vím, co to způsobuje. V tom návodu ten cápek psal, že mu to dělá, když to vypojí a jede z baterky.
Mě to po tom přidání parametru fungovalo, ale chtěl jsem vědět, jestli to pojede i když vypojím adaptér.
V momentě kdy jsem sklopil LCD, přestalo to fungovat.
Restartoval jsem to 7 krát, vždy myš funguje, ale jakmile trochu přiklopím displej, USBčka se vypnou.
Přitom toho kontaktu, co kontroluje jestli se displej zaklopil se to ani nedotkne.
To asi nebude záležitost SW. Alespoň se vyřešilo to, že funguje po restartu, předtím jsem to mohl restartovat 20x a ta myš nenaskočila.
-
USB porty nevypíná snímač zavření LCD, někteří výrobci na to používají pro úsporu energie kontakt přímo v pantu
-
USB porty nevypíná snímač zavření LCD, někteří výrobci na to používají pro úsporu energie kontakt přímo v pantu
Je to ntb HP, je tedy nějaká možnost vypnout to šetření energie vůči USB ?
Promiň, že se tak laicky ptám :D
-
Obávám se, že to šteluje BIOS, možná by stálo za zvážení provést jeho update. HP je bohužel známé tím, že má v BIOSech dost chyb
-
Obávám se, že to šteluje BIOS, možná by stálo za zvážení provést jeho update. HP je bohužel známé tím, že má v BIOSech dost chyb
Dejme tomu, že s tím už moc nezmůžu, model to není nejnovější.
Dotaz do budoucna, myslíš že budu mít obdobné problémy na lenovu (L412) ? Plánuju si jedno koupit, ale četl jsem zde na foru, že Lenovo řeší dost chyb v biosu ovladači ve Win.. tak jestli se pohnu z místa, nebo to bude podobné.
-
Spíš horší, Lenovo jsou příšerné krámy. Uvažoval bych spíš o Asus nebo o Aceru, pokud se vyhneš nejlevnější řadě Aspire, tam má Acer dobré jen netbooky.
Lenovo řeší ten svůj nefungující BIOS i HW právě ovladači do Windows. Je to výhodné, jednak zabrání zákazníkovi instalovat cokoli jiného než dodaný OS, protože ty jejich ovladače plné bugů ani na jiném než dodaném systému správně nefungují a pak je tu samozřejmě věc, která se asi hodí všem výrobcům. Nešetrné chování Windows k HW, nerespektování některých nastavení BIOSu (od W98) a povolení nebezpečných funkcí v jádru, které mohou počítač poškodit, obvykle kvůli jedinému, jejich zakázáním by některé (velmi agresivní) DRM ochrany přestaly fungovat.
-
Škoda, Ubunty mě baví, tak jsem je chtěl dát na nějakej silnější notebook, než je tenhle (1,86 single core, 1,5gb ram) a asi to nikam nepovede.
Na pevném počítači je mám, ale vzhledem k tomu, že po večerech si sem tam něco zahraju, tak spíše prerefruju na pevném PC win.
Ptám se protože jsem si vygooglil tohle a říkají, že je to naprosto v pohodě
http://www.ubuntu.com/certification/hardware/201101-6966/
-
Pokud je to certifikovaný HW, tak by mělo vše fungovat bez nutnosti zásahu do systému, ale dost mě překvapuje, že se nějaké Lenovo vůbec dostalo mezi certifikovaný HW. Obvykle musím pro Lenova patchovat jádro (ovladače), protože nic na nich nefunguje normálně
-
Dejme tomu, že to shrneme.
S tím HP, co se mu vypínají USBčka ti došli nápady, krom aktualizace biosu, což se mi nechce na úkor stáří notebooku.
A s tím lenovem, ubuntu zkusím, ale říkáš že na Lenovech to žádná sláva není.
Pokud je to tak, tak asi zamknu téma.
-
Asi tak, kromě aktualizace BIOSu už mě u toho HP nenapadá co s tím. Kdyby ten počítač uspával jen obsazená USB jak to občas na některých strojích blbne, tak bych možná pár věcí ještě věděl, jenže tenhle prostě vypne kompletně celý HUB uvnitř. Ale něco mě ještě napadlo, ale bude to trochu delší.
Do stejného řádku jako jsi přidával "acpi_osi=Linux" dodej ještě tohle "pcie_aspm=force" bude to tedy vypadat takhle GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=Linux pcie_aspm=force" pak aktualizuj GRUB sudo update-grub a po restartu moduly jádra sudo update-initramfs -u trvá to dlouho, tak počkat.
Teď zadej sudo gedit /etc/modprobe.d/usbcore.conf to by mělo vytvořit prázdný soubor, do něj vlož tohle options usbcore autosuspend=0 po restartu znovu aktualizuj moduly sudo update-initramfs -u
-
Dnes po 5ti minutách používání notebooku z baterky se myš vypla.
Z elektriky funguje, zatím..
-
Pro vyřešení by to asi opravdu chtělo dát tam novější BIOS, pokud je nějaký k dispozici. Obvykle to není těžké, můžu se na to podívat co HP pro tento notebook nabízí, ale potřeboval bych vědět přesný model + verzi BIOSu
-
Tak je to HP compaq nc6120, verze biosu 1.15
Teďka nefunguje myška a externí disk jenom na USB funguje
-
Já mám trochu problém, nemůžu moc psát, včera jsem si totálně zničil levou ruku, nicméně k tomu notebooku už jsem něco pohledal.
HP opět nezklamalo, bezproblémový update BIOSu je možný pouze z Windows, ostatní metody jsou poměrně komplikované a jak už to tak bývá dělat update BIOSu na používaných Windows, to zavání průšvihem, takže aby si k tomu ještě člověk nainstaloval čistý systém.
Poslední verze BIOSu na stránkách HP je označena jako F.14 a je z 27.7.2006
Na tu myš zkus ještě tohle sudo echo 'ACTION=="add", SUBSYSTEM=="usb", TEST=="power/control" ATTR{power/control}="on"' >/etc/udev/rules.d/usb_power_save.rules
-
V nastavení BIOSu problém není? Vlákno jsem prošel a nevšiml jsem si.
Sestře jsem aktualizoval BIOS na HP620 z běžících WXP bez problémů.
-
honza@honza-HP-Compaq-nc6120-PY507EA-AKB:~$ sudo echo 'ACTION=="add", SUBSYSTEM=="usb", TEST=="power/control" ATTR{power/control}="on"' >/etc/udev/rules.d/usb_power_save.rules
bash: /etc/udev/rules.d/usb_power_save.rules: Operace zamítnuta
Na heslo su se to ani nezeptalo..
-
protože tím myslel, že se to přidá do souboru kde jsou existující podadresáře, zkontroluj to.
-
v tom případě usb_power_save.rules v tý složce vůbec není.
Je tam jenom 70-prersistent cd, net a readme. Toť vše. Vytvořit file tam na klikačku nejde.
-
máš pravdu, zřejmě to bude mít potíže s oprávněním pro /etc/sudoers
musíš se stát adminem (root)
sudo -iecho 'ACTION=="add", SUBSYSTEM=="usb", TEST=="power/control" ATTR\{power/control\}="on"' > /etc/udev/rules.d/80-usb-power-save.rulesexitčíslo 80 jsem zvolil aby bylo poznat co tam bylo dáno naposledy, a také se z toho bude naposledy číst.
-
Ten file už tam je, chceš po mě nějaký výpis ?
btw, myška pořád nic
-
ne já s tím nezačal, jen jsem ti upřesnil .. mám omezené kapacity
-
ne já s tím nezačal, jen jsem ti upřesnil .. mám omezené kapacity
Jo takhle :D , ale děkuju ;)
-
Zkus tomu souboru ještě přidělit spustitelný příznak
-
Zkus tomu souboru ještě přidělit spustitelný příznak
obávám se, že ani to nepomůže, teď jsem si všiml, že tam má můj experiment, když jsem zjišťoval proč to nejde..
echo 'ACTION=="add", SUBSYSTEM=="usb", TEST=="power/control" ATTR\{power/control\}="on"' > /etc/udev/rules.d/80-usb-power-save.rules
echo 'ACTION=="add", SUBSYSTEM=="usb", TEST=="power/control" ATTR{power/control}="on"' > /etc/udev/rules.d/80-usb-power-save.rulesty escape znaky před složenýma závorkama, teď to je správně, jak to chtěl Rover623, takže znovu ono se to přepíše
-
ani tohle nepomohlo..
opět přidávám dmesg
[ 1.065405] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.065412] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.109033] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.109065] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.109096] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.109233] mousedev: PS/2 mouse device common for all mice
[ 1.109420] rtc_cmos 00:08: RTC can wake from S4
[ 1.109564] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.109611] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.109679] device-mapper: uevent: version 1.0.3
[ 1.109759] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 1.109784] EISA: Probing bus 0 at eisa.0
[ 1.109792] Cannot allocate resource for EISA slot 1
[ 1.109794] Cannot allocate resource for EISA slot 2
[ 1.109796] Cannot allocate resource for EISA slot 3
[ 1.109799] Cannot allocate resource for EISA slot 4
[ 1.109810] Cannot allocate resource for EISA slot 7
[ 1.109816] EISA: Detected 0 cards.
[ 1.109862] cpuidle: using governor ladder
[ 1.109901] cpuidle: using governor menu
[ 1.109904] EFI Variables Facility v0.08 2004-May-17
[ 1.110109] ashmem: initialized
[ 1.110279] TCP: cubic registered
[ 1.110423] NET: Registered protocol family 10
[ 1.110670] NET: Registered protocol family 17
[ 1.110684] Key type dns_resolver registered
[ 1.110803] Using IPI No-Shortcut mode
[ 1.110907] PM: Hibernation image not present or could not be loaded.
[ 1.110924] registered taskstats version 1
[ 1.113632] Key type trusted registered
[ 1.115732] Key type encrypted registered
[ 1.118262] Magic number: 9:155:12
[ 1.118418] rtc_cmos 00:08: setting system clock to 2013-08-22 05:01:09 UTC (1377147669)
[ 1.122655] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.122657] EDD information not available.
[ 1.210417] isapnp: No Plug & Play device found
[ 1.211049] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.224362] ata1.00: ATA-6: ST9808211A, 3.02, max UDMA/100
[ 1.224366] ata1.00: 156301488 sectors, multi 16: LBA48
[ 1.224373] ata1.01: ATAPI: HL-DT-ST DVD-RW GWA-4082N, CC15, max MWDMA2
[ 1.238502] ACPI: Battery Slot [C174] (battery present)
[ 1.240279] ata1.00: configured for UDMA/100
[ 1.256279] ata1.01: configured for MWDMA2
[ 1.258762] scsi 0:0:0:0: Direct-Access ATA ST9808211A 3.02 PQ: 0 ANSI: 5
[ 1.258942] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.259044] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.259103] sd 0:0:0:0: [sda] Write Protect is off
[ 1.259107] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.259133] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.313597] sda: sda1 sda2 < sda5 >
[ 1.313932] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.317954] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-RW GWA-4082N CC15 PQ: 0 ANSI: 5
[ 1.323110] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 1.323114] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.323236] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 1.323300] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 1.323408] Freeing unused kernel memory: 760k freed
[ 1.323800] Write protecting the kernel text: 6056k
[ 1.323822] Write protecting the kernel read-only data: 2480k
[ 1.323824] NX-protecting the kernel data: 4184k
[ 1.342405] udevd[90]: starting version 175
[ 1.560060] usb 2-2: new low-speed USB device number 2 using uhci_hcd
[ 1.578277] sdhci: Secure Digital Host Controller Interface driver
[ 1.578283] sdhci: Copyright(c) Pierre Ossman
[ 1.578619] sdhci-pci 0000:02:06.4: SDHCI controller found [104c:8034] (rev 0)
[ 1.578710] mmc0: no vmmc regulator found
[ 1.578747] Registered led device: mmc0::
[ 1.615102] mmc0: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.615157] mmc1: no vmmc regulator found
[ 1.615203] Registered led device: mmc1::
[ 1.644058] mmc1: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.644103] mmc2: no vmmc regulator found
[ 1.644149] Registered led device: mmc2::
[ 1.676604] mmc2: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.676765] tg3.c:v3.123 (March 21, 2012)
[ 1.743334] tg3 0000:02:0e.0: eth0: Tigon3 [partno(BCM95705A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:14:c2:dd:ce:3c
[ 1.743342] tg3 0000:02:0e.0: eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0])
[ 1.743346] tg3 0000:02:0e.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.743349] tg3 0000:02:0e.0: eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
[ 1.767676] usb 2-2: New USB device found, idVendor=04b3, idProduct=310c
[ 1.767682] usb 2-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1.767686] usb 2-2: Product: USB Optical Mouse
[ 1.797116] firewire_ohci 0000:02:06.2: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
[ 1.812905] usbcore: registered new interface driver usbhid
[ 1.812908] usbhid: USB HID core driver
[ 1.823378] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input4
[ 1.824100] hid-generic 0003:04B3:310C.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.0-2/input0
[ 1.982576] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.296159] firewire_core 0000:02:06.2: created device fw0: GUID 718b500029314ca6, S400
[ 16.867071] Adding 1562620k swap on /dev/sda5. Priority:-1 extents:1 across:1562620k
[ 16.880035] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.920408] udevd[336]: starting version 175
[ 16.999337] lp: driver loaded but no devices found
[ 17.069159] ACPI: Video Device [C055] (multi-head: yes rom: no post: no)
[ 17.072314] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 17.168755] [drm] Initialized drm 1.1.0 20060810
[ 17.184954] wmi: Mapper loaded
[ 17.234925] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 17.390210] i915 0000:00:02.0: setting latency timer to 64
[ 17.391449] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 17.391454] [drm] Driver supports precise vblank timestamp query.
[ 17.457530] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 17.499704] parport_pc 00:04: reported by Plug and Play ACPI
[ 17.499788] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 17.501797] irda_init()
[ 17.501814] NET: Registered protocol family 23
[ 17.527096] found SMC SuperIO Chip (devid=0x7a rev=00 base=0x004e): LPC47N227
[ 17.527120] smsc_superio_flat(): fir: 0x100, sir: 0x3e8, dma: 03, irq: 3, mode: 0x0e
[ 17.527127] smsc_ircc_present: can't get sir_base of 0x3e8
[ 17.538674] intel_rng: FWH not detected
[ 17.556426] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:099c]
[ 17.556453] yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
[ 17.556460] yenta_cardbus 0000:02:06.0: Using INTVAL to route CSC interrupts to PCI
[ 17.556463] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
[ 17.556471] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01aa1b22, devctl 0x64
[ 17.556567] lib80211: common routines for IEEE802.11 drivers
[ 17.556570] lib80211_crypt: registered algorithm 'NULL'
[ 17.582760] cfg80211: Calling CRDA to update world regulatory domain
[ 17.600254] lp0: using parport0 (interrupt-driven).
[ 17.601443] libipw: 802.11 data/management/control stack, git-1.1.13
[ 17.601446] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 17.602814] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 17.602817] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 17.644178] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
[ 17.738858] type=1400 audit(1377147686.115:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=569 comm="apparmor_parser"
[ 17.741130] type=1400 audit(1377147686.119:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=569 comm="apparmor_parser"
[ 17.741462] type=1400 audit(1377147686.119:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=569 comm="apparmor_parser"
[ 17.788997] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0c78, PCI irq 18
[ 17.789005] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 17.789014] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
[ 17.789018] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x4fff:
[ 17.790311] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff 0x4c00-0x4cff
[ 17.853139] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd03fffff]
[ 17.853146] pcmcia_socket pcmcia_socket0: cs: memory probe 0xd0000000-0xd03fffff:
[ 17.853151] excluding 0xd0000000-0xd003ffff
[ 17.853168] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x60000000-0x67ffffff pref]
[ 17.853171] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x67ffffff:
[ 17.853185] excluding 0x60000000-0x67ffffff
[ 17.891530] Bluetooth: Core ver 2.16
[ 17.891550] NET: Registered protocol family 31
[ 17.891551] Bluetooth: HCI device and connection manager initialized
[ 17.891552] Bluetooth: HCI socket layer initialized
[ 17.891553] Bluetooth: L2CAP socket layer initialized
[ 17.891557] Bluetooth: SCO socket layer initialized
[ 17.903437] [drm] initialized overlay support
[ 17.912119] yenta_cardbus 0000:02:06.1: CardBus bridge found [103c:099c]
[ 17.912149] yenta_cardbus 0000:02:06.1: Using CSCINT to route CSC interrupts to PCI
[ 17.912152] yenta_cardbus 0000:02:06.1: Routing CardBus interrupts to PCI
[ 17.912159] yenta_cardbus 0000:02:06.1: TI: mfunc 0x01aa1b22, devctl 0x64
[ 17.923312] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.923318] Bluetooth: BNEP filters: protocol multicast
[ 17.966888] Bluetooth: RFCOMM TTY layer initialized
[ 17.966902] Bluetooth: RFCOMM socket layer initialized
[ 17.966904] Bluetooth: RFCOMM ver 1.11
[ 18.103621] init: failsafe main process (702) killed by TERM signal
[ 18.147043] yenta_cardbus 0000:02:06.1: ISA IRQ mask 0x0c78, PCI irq 19
[ 18.147052] yenta_cardbus 0000:02:06.1: Socket status: 30000006
[ 18.147057] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #04 to #07
[ 18.147069] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
[ 18.147073] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x4000-0x4fff:
[ 18.246508] psmouse serio4: synaptics: Touchpad model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000/0x0
[ 18.246519] psmouse serio4: synaptics: serio: Synaptics pass-through port at isa0060/serio4/input0
[ 18.304602] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input6
[ 18.305140] ppdev: user-space parallel port driver
[ 18.390573] type=1400 audit(1377147686.767:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=796 comm="apparmor_parser"
[ 18.406874] type=1400 audit(1377147686.783:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=798 comm="apparmor_parser"
[ 18.407355] type=1400 audit(1377147686.783:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=798 comm="apparmor_parser"
[ 18.412829] type=1400 audit(1377147686.791:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=796 comm="apparmor_parser"
[ 18.439155] type=1400 audit(1377147686.815:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=807 comm="apparmor_parser"
[ 18.439736] type=1400 audit(1377147686.815:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=807 comm="apparmor_parser"
[ 18.211770] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff 0x4c00-0x4cff
[ 18.456481] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd03fffff]
[ 18.456490] pcmcia_socket pcmcia_socket1: cs: memory probe 0xd0000000-0xd03fffff:
[ 18.456494] excluding 0xd0000000-0xd003ffff
[ 18.456511] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge window: [mem 0x60000000-0x67ffffff pref]
[ 18.456514] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x67ffffff:
[ 18.456528] excluding 0x60000000-0x67ffffff
[ 18.456675] type=1400 audit(1377147686.835:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=807 comm="apparmor_parser"
[ 18.501196] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 18.655000] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 18.686676] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[ 18.687665] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 18.694261] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[ 18.694604] excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 18.694943] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[ 18.695518] clean.
[ 18.695536] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[ 18.723818] cfg80211: World regulatory domain updated:
[ 18.723825] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 18.723828] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.723831] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.723833] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.723836] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.723839] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.724790] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 19.047476] clean.
[ 19.047529] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[ 19.047535] excluding 0xc0000-0xc7fff 0xe0000-0xfffff
[ 19.047566] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[ 19.047583] clean.
[ 19.047600] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[ 19.047615] excluding 0x60000000-0x60ffffff
[ 19.047635] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[ 19.061036] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af:
[ 19.062026] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 19.062742] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff:
[ 19.072071] clean.
[ 19.170903] excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 19.171281] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff:
[ 19.171857] clean.
[ 19.171875] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7:
[ 19.184578] clean.
[ 19.184627] pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0fffff:
[ 19.184632] excluding 0xc0000-0xc7fff 0xe0000-0xfffff
[ 19.184663] pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff:
[ 19.184681] clean.
[ 19.184698] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff:
[ 19.184712] excluding 0x60000000-0x60ffffff
[ 19.184732] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff:
[ 19.185390] clean.
[ 19.207158] fbcon: inteldrmfb (fb0) is primary device
[ 19.209854] Console: switching to colour frame buffer device 128x48
[ 19.209896] fb0: inteldrmfb frame buffer device
[ 19.209899] drm: registered panic notifier
[ 19.209912] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 19.209958] ACPI Warning: 0x00001060-0x0000107f SystemIO conflicts with Region \_SB_.C002.C003.C08F 1 (20120320/utaddress-251)
[ 19.209965] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 19.209968] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
[ 19.209972] ACPI Warning: 0x00001028-0x0000102f SystemIO conflicts with Region \_SB_.C002.C003.C086 1 (20120320/utaddress-251)
[ 19.209977] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 19.209981] ACPI Warning: 0x00001100-0x0000113f SystemIO conflicts with Region \_SB_.C002.C003.C097 1 (20120320/utaddress-251)
[ 19.209986] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 19.209988] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 19.212792] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 19.483689] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483695] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483698] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483701] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483703] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483706] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483708] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483711] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483714] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483716] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483719] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483721] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483724] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483727] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483729] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483732] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483734] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483737] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483739] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483742] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483745] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483747] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.483750] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483753] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.483755] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483758] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.483760] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 19.483763] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.515485] init: alsa-restore main process (895) terminated with status 19
[ 19.655076] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.655655] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
[ 19.669325] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.208039] intel8x0_measure_ac97_clock: measured 55488 usecs (2673 samples)
[ 20.208046] intel8x0: clocking to 48000
[ 20.550495] lib80211_crypt: registered algorithm 'TKIP'
[ 394.788374] audit_printk_skb: 39 callbacks suppressed
[ 394.788386] type=1400 audit(1377148062.274:25): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=805 comm="cupsd" pid=805 comm="cupsd" capability=36 capname="block_suspend"
[ 2154.034558] pci 0000:00:1e.0: wake-up capability enabled by ACPI
[ 2160.079371] PM: Syncing filesystems ... done.
[ 2160.090429] PM: Preparing system for mem sleep
[ 2160.161441] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 2160.176186] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 2160.192076] PM: Entering mem sleep
[ 2160.192097] Suspending console(s) (use no_console_suspend to debug)
[ 2160.192772] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 2160.212773] sd 0:0:0:0: [sda] Stopping disk
[ 2160.242068] parport_pc 00:04: disabled
[ 2160.242529] serial 00:02: disabled
[ 2160.242962] ACPI handle has no context!
[ 2160.242972] ACPI handle has no context!
[ 2160.243048] ACPI handle has no context!
[ 2160.243079] eth1: Going into suspend...
[ 2162.483191] PM: suspend of drv:sd dev:0:0:0:0 complete after 2290.416 msecs
[ 2162.483209] PM: suspend of drv:scsi dev:target0:0:0 complete after 2290.352 msecs
[ 2162.483218] PM: suspend of drv:scsi dev:host0 complete after 2242.232 msecs
[ 2162.483262] PM: suspend of drv: dev:ata1 complete after 2240.458 msecs
[ 2162.483316] PM: suspend of drv:ata_piix dev:0000:00:1f.1 complete after 2240.197 msecs
[ 2162.483326] PM: suspend of drv: dev:pci0000:00 complete after 2239.374 msecs
[ 2162.483333] PM: suspend of devices complete after 2291.017 msecs
[ 2162.483335] PM: suspend devices took 2.288 seconds
[ 2162.483599] PM: late suspend of devices complete after 0.260 msecs
[ 2162.484329] ehci_hcd 0000:00:1d.7: wake-up capability enabled by ACPI
[ 2162.500087] uhci_hcd 0000:00:1d.3: wake-up capability enabled by ACPI
[ 2162.500145] uhci_hcd 0000:00:1d.2: wake-up capability enabled by ACPI
[ 2162.500202] uhci_hcd 0000:00:1d.1: wake-up capability enabled by ACPI
[ 2162.500259] uhci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[ 2162.500399] PM: noirq suspend of devices complete after 16.797 msecs
[ 2162.500563] ACPI: Preparing to enter system sleep state S3
[ 2162.500699] PM: Saving platform NVS memory
[ 2162.500789] Disabling non-boot CPUs ...
[ 2162.500789] ACPI: Low-level resume complete
[ 2162.500789] PM: Restoring platform NVS memory
[ 2162.500789] Force enabled HPET at resume
[ 2162.500789] ACPI: Waking up from system sleep state S3
[ 2162.629872] uhci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[ 2162.629936] uhci_hcd 0000:00:1d.1: wake-up capability disabled by ACPI
[ 2162.629999] uhci_hcd 0000:00:1d.2: wake-up capability disabled by ACPI
[ 2162.630061] uhci_hcd 0000:00:1d.3: wake-up capability disabled by ACPI
[ 2162.630114] ehci_hcd 0000:00:1d.7: wake-up capability disabled by ACPI
[ 2162.631649] PM: noirq resume of devices complete after 2.141 msecs
[ 2162.631814] PM: early resume of devices complete after 0.104 msecs
[ 2162.631896] i915 0000:00:02.0: setting latency timer to 64
[ 2162.670738] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2162.670763] usb usb2: root hub lost power or was reset
[ 2162.670780] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2162.670803] usb usb3: root hub lost power or was reset
[ 2162.670820] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2162.670843] usb usb4: root hub lost power or was reset
[ 2162.670860] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 2162.670883] usb usb5: root hub lost power or was reset
[ 2162.670902] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2162.670928] pci 0000:00:1e.0: setting latency timer to 64
[ 2162.670942] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 2162.670980] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 2162.670987] eth1: Coming out of suspend...
[ 2162.671094] pci 0000:00:1e.0: wake-up capability disabled by ACPI
[ 2162.674041] ata1.01: _GTF evaluation failed (AE 0x1001)
[ 2162.674093] ata2: port disabled--ignoring
[ 2162.803611] PM: resume of drv:hub dev:1-0:1.0 complete after 129.483 msecs
[ 2162.803699] PM: resume of drv: dev:ep_00 complete after 129.563 msecs
[ 2162.803705] PM: resume of drv: dev:ep_81 complete after 129.575 msecs
[ 2162.836093] PM: resume of drv:hub dev:3-0:1.0 complete after 133.852 msecs
[ 2162.836099] PM: resume of drv: dev:ep_00 complete after 133.824 msecs
[ 2162.836103] PM: resume of drv:hub dev:4-0:1.0 complete after 133.789 msecs
[ 2162.836109] PM: resume of drv: dev:ep_00 complete after 101.821 msecs
[ 2162.836113] PM: resume of drv: dev:ep_81 complete after 133.855 msecs
[ 2162.836117] PM: resume of drv: dev:ep_81 complete after 101.842 msecs
[ 2162.904072] PM: resume of drv:hub dev:5-0:1.0 complete after 163.257 msecs
[ 2162.904078] PM: resume of drv: dev:ep_00 complete after 163.229 msecs
[ 2162.904082] PM: resume of drv: dev:ep_81 complete after 163.250 msecs
[ 2162.908070] PM: resume of drv:hub dev:2-0:1.0 complete after 233.872 msecs
[ 2162.908076] PM: resume of drv: dev:ep_00 complete after 205.879 msecs
[ 2162.908080] PM: resume of drv:usb dev:2-2 complete after 104.368 msecs
[ 2162.908100] PM: resume of drv: dev:ep_81 complete after 233.899 msecs
[ 2162.964885] serial 00:02: activated
[ 2162.966502] parport_pc 00:04: activated
[ 2163.168070] usb 2-2: reset low-speed USB device number 2 using uhci_hcd
[ 2163.300082] firewire_core 0000:02:06.2: rediscovered device fw0
[ 2163.484216] PM: resume of drv:usbhid dev:2-2:1.0 complete after 680.495 msecs
[ 2163.484222] PM: resume of drv: dev:ep_00 complete after 680.465 msecs
[ 2163.484226] PM: resume of drv: dev:ep_81 complete after 680.487 msecs
[ 2164.596395] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 2164.596398] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 2164.596401] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2164.596404] ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2164.596590] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 2164.620278] ata1.00: configured for UDMA/100
[ 2164.636275] ata1.01: configured for MWDMA2
[ 2164.745588] PM: resume of drv:scsi dev:host0 complete after 2071.511 msecs
[ 2164.745599] PM: resume of drv:ata_port dev:ata1 complete after 1778.582 msecs
[ 2164.747254] PM: resume of drv:scsi_host dev:host0 complete after 2073.147 msecs
[ 2164.747259] PM: resume of drv:scsi dev:target0:0:0 complete after 2006.395 msecs
[ 2164.747266] PM: resume of drv:scsi dev:target0:0:1 complete after 2006.345 msecs
[ 2164.747272] PM: resume of drv:sd dev:0:0:0:0 complete after 2006.389 msecs
[ 2164.747276] sd 0:0:0:0: [sda] Starting disk
[ 2164.747283] PM: resume of drv:sr dev:0:0:1:0 complete after 1943.663 msecs
[ 2164.747290] PM: resume of drv:scsi_device dev:0:0:1:0 complete after 1943.584 msecs
[ 2164.778225] PM: resume of drv:scsi_device dev:0:0:0:0 complete after 2037.316 msecs
[ 2165.078999] PM: resume of devices complete after 2447.176 msecs
[ 2165.079180] PM: resume devices took 2.448 seconds
[ 2165.079279] PM: Finishing wakeup.
[ 2165.079281] Restarting tasks ... done.
[ 2165.125656] video LNXVIDEO:00: Restoring backlight state
[ 2167.038383] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2167.240200] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 2168.506125] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 2500.423201] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 2500.438649] JFS: nTxBlock = 8192, nTxLock = 65536
[ 2500.521411] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 2500.636130] QNX4 filesystem 0.2.3 registered.
[ 2500.702643] Btrfs loaded
[ 2550.036005] uhci_hcd 0000:00:1d.0: host controller process error, something bad happened!
[ 2550.036020] uhci_hcd 0000:00:1d.0: host controller halted, very bad!
[ 2550.036044] uhci_hcd 0000:00:1d.0: HC died; cleaning up
[ 2550.036092] usb 2-2: USB disconnect, device number 2
honza@honza-HP-Compaq-nc6120-PY507EA-AKB:~$
-
změň verzi jádra,
jo a ještě něco v prvních příspěvcích si nesplnil rady jako vyndat akumulátor, psals jen o vyndaném napájení.
Sice tohle jsem potřeboval jen když se mi nechtěl zapnout laptop a ono to stejně asi nepomůže ale ..
A co to nastavení biosu, nevrátilo se z ničeho nic na výchozí hodnoty položky ovlivňující usb porty.
Co já vím co máš v biosu..
-
co tak koukám do biosu tak by mohlo bejt k věci je
USB legacy support - enable
parallel port mode - ecp
intel execution disable - enabled