Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Internet a sítě => Téma založeno: Fatima 16 Dubna 2014, 14:33:55
-
Dobrý den, prosím o radu a předem upozorňuji , že jsem začátečník a laik. Na starý notebook /HP Compaq nx6325, karta Broadcom BCM 4311 802.11a/b/g rev 01/ jsme nainstalovali UBuntu 12.04.4 LTS a nefunguje wifi. Přitom ve Windows fungovalo normálně, připojení po drátě je vpořádku, udělala jsem update a upgrade, přidala ovladač Linus STA driver a B43 a dále nějaké ovladače přes ndiswrapper, ale všechno neúspěšně. Předem děkuji.
-
Zkuste nainstalovat balík bcmwl-kernel-source.
sudo apt-get install bcmwl-kernel-sourceA ještě odinstalujte ten ndiswrapper.
-
Zkuste nainstalovat balík bcmwl-kernel-source.
sudo apt-get install bcmwl-kernel-sourceA ještě odinstalujte ten ndiswrapper.
Neměl by tam být jenom b43?
edit : už si nevzpomenu, v kterém vlákně jsme to řešily, ale tady je návod : http://askubuntu.com/questions/55868/how-to-install-broadcom-wireless-drivers-bcm43xx
-
Děkuji, ten balík už je instalovaný, zkoušela jsem ho i odstranit a nechat jen B43, ale žádná kombinace nefunguje. Ndiswrapper už je také odinstalován.
-
Děkuji, ten balík už je instalovaný, zkoušela jsem ho i odstranit a nechat jen B43, ale žádná kombinace nefunguje. Ndiswrapper už je také odinstalován.
Takže je tam jenom b43 ? Jenom blbá otázka, proběhl mezitím restart ?
-
sudo apt-get install firmware-b43-installer a přestaňte vymejšlet kraviny, rozchodit tyhle karty je snadné, jen u toho člověk nesmí přemejšlet jak ve Windows
-
sudo apt-get install firmware-b43-installer a přestaňte vymejšlet kraviny, rozchodit tyhle karty je snadné, jen u toho člověk nesmí přemejšlet jak ve Windows
Vždyť jo, prý ho instalovali, ale asi nerestartovali.
-
Ale jestli je ta karta lpphy, tak to stejně fungovat nebude, chtělo by to
lspci
-
Teď jsou tam oba, ale nefunovalo to ani s jedním zvlášť. A restarovat počítač napadne i mě blondýnu...
-
Teď jsou tam oba, ale nefunovalo to ani s jedním zvlášť. A restarovat počítač napadne i mě blondýnu...
Jak oba ? Lepší bude ten výpis, jak psal Rover623
lspci
-
omlouvám se, ale nevím, jak to sem vložit.
-
omlouvám se, ale nevím, jak to sem vložit.
Nad smajlíkama je # tak do toho.
-
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD/ATI] RS480/RS482/RS485 Host Bridge (rev 10)
00:01.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Bridge [int gfx]
00:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Express Port 1
00:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Express Port 2
00:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Express Port 3
00:12.0 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 Serial ATA Controller (rev 80)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 USB Host Controller (rev 80)
00:13.1 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 USB Host Controller (rev 80)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 USB2 Host Controller (rev 80)
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 SMBus Controller (rev 82)
00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 IDE Controller (rev 80)
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 High Definition Audio Controller (rev 01)
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 PCI-ISA Bridge (rev 80)
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 PCI-PCI Bridge (rev 80)
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RS482M [Mobility Radeon Xpress 200]
02:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
02:04.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
02:04.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller
02:04.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
02:04.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
30:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01)
-
Mělo by to být v tom rámečku, ale to se kdyžtak upraví.
Takže, teď by to mělo vypadat následovně.
sudo apt-get remove bcmwl-kernel-source
sudo apt-get install firmware-b43-installer b43-fwcutter
pak se podívat, zda je bcm na blacklistu
cat /etc/modprobe.d/* | egrep 'bcm'
pokud ano, přepíšeme soubor blacklist.conf
cd /etc/modprobe.d/
sudo gedit blacklist.conf
najdeme "blacklist bcm43xx" a na začátek napíšeme #
to je z toho návodu.
-
Odpověď #12
za to sa nedá nedať K+ :)
[code]sem[/code] ;)
-
Odpověď #12
za to sa nedá nedať K+ :)
Prostě se tam tomu nechce. :D
-
Tak jsem se to pokusila provést, výsledek je:
# replaced by b43 and ssb.
# blacklist bcm43xx
a už by to mělo fungovat?
Restarovala jsem počítač, ale nic..
Děkuji za shovívavost.
-
Je to ztracené nebo mám ještě doufat, že má úloha nějaké řešení?
-
daj sem ešte prosím výpis z tohto
lspci -vk
-
[]helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ lspci -vk
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD/ATI] RS480/RS482/RS485 Host Bridge (rev 10)
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 64
Kernel modules: ati-agp
00:01.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Bridge [int gfx] (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: d4300000-d43fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
Capabilities: <access denied>
Kernel modules: shpchp
00:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Express Port 1 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
I/O behind bridge: 00004000-00005fff
Memory behind bridge: d0000000-d3ffffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Express Port 2 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: cc000000-cfffffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RC4xx/RS4xx PCI Express Port 3 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
Memory behind bridge: c8000000-c80fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:12.0 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 Serial ATA Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
I/O ports at 9000 [size=8]
I/O ports at 9008 [size=4]
I/O ports at 9010 [size=8]
I/O ports at 7018 [size=4]
I/O ports at 7020 [size=16]
Memory at d4409000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 44000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil
Kernel modules: sata_sil
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 USB Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
Memory at d4401000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:13.1 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 USB Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
Memory at d4402000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 USB2 Host Controller (rev 80) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
Memory at d4403000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 SMBus Controller (rev 82)
Subsystem: Hewlett-Packard Company Device 30b0
Flags: 66MHz, medium devsel
I/O ports at 8200 [size=16]
Memory at d4404000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 IDE Controller (rev 80) (prog-if 82 [Master PriP])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at 7040 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
Kernel modules: pata_atiixp
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 High Definition Audio Controller (rev 01)
Subsystem: Device 30b0:103c
Flags: bus master, slow devsel, latency 64, IRQ 16
Memory at 44080000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd-hda-intel
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 PCI-ISA Bridge (rev 80)
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, 66MHz, medium devsel, latency 0
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] IXP SB4x0 PCI-PCI Bridge (rev 80) (prog-if 01 [Subtractive decode])
Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d4000000-d42fffff
Prefetchable memory behind bridge: 40000000-43ffffff
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: <access denied>
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
Kernel driver in use: k8temp
Kernel modules: k8temp
01:05.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RS482M [Mobility Radeon Xpress 200] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, fast Back2Back, 66MHz, medium devsel, latency 64, IRQ 17
Memory at c0000000 (32-bit, prefetchable) [size=128M]
I/O ports at 6000 [size=256]
Memory at d4300000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d4320000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
Kernel modules: radeon, radeonfb
02:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
Subsystem: Hewlett-Packard Company Device 30b0
Physical Slot: 1-2
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 23
Memory at d4000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
02:04.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, medium devsel, latency 168, IRQ 20
Memory at d4010000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 48000000-4bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:04.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at d4011000 (32-bit, non-prefetchable) [size=2K]
Memory at d4014000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
02:04.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at d4018000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: tifm_7xx1
Kernel modules: tifm_7xx1
02:04.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
Subsystem: Hewlett-Packard Company Device 30b0
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at d4019000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
30:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01)
Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at c8000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel modules: ssb
-
skús
sudo modprobe b43a reštart alebo vypnúť zapnúť wifi
-
Je to ztracené nebo mám ještě doufat, že má úloha nějaké řešení?
wifi bude fungovať, len potrebuješ firmware, bez ktorého to nejde ... ( je to ošetrené licenciou... ) A to nainštaluješ absolútne jednoducho .
Pripoj sa na sieť káblom, a nainštaluj si tento balík, sudo apt-get install linux-firmware-nonfree potom , aby si nemusela pc reštartovať natiahni ovládač " b43" ručne a wifi proste musí fungovať ...
sudo modprobe b43 tiež dávam +K , za snahu .
PS pre istotu si skontroluj firmware , musí byť skopírované v /lib/firmware/b43 ... malo by to vyzertať asi takot nejako :/lib/firmware/b43/ucode11.fw
/lib/firmware/b43/ucode13.fw
/lib/firmware/b43/ucode14.fw
/lib/firmware/b43/ucode15.fw
/lib/firmware/b43/ucode16_lp.fw
/lib/firmware/b43/ucode16_mimo.fw
/lib/firmware/b43/ucode16_sslpn.fw
/lib/firmware/b43/ucode16_sslpn_nobt.fw
/lib/firmware/b43/ucode17_mimo.fw
/lib/firmware/b43/ucode19_sslpn.fw
/lib/firmware/b43/ucode19_sslpn_nobt.fw
/lib/firmware/b43/ucode20_sslpn.fw
/lib/firmware/b43/ucode20_sslpn_nobt.fw
/lib/firmware/b43/ucode21_sslpn.fw
/lib/firmware/b43/ucode21_sslpn_nobt.fw
/lib/firmware/b43/ucode22_mimo.fw
/lib/firmware/b43/ucode22_sslpn.fw
/lib/firmware/b43/ucode24_lcn.fw
/lib/firmware/b43/ucode24_mimo.fw
/lib/firmware/b43/ucode25_lcn.fw
/lib/firmware/b43/ucode25_mimo.fw
/lib/firmware/b43/ucode26_mimo.fw
/lib/firmware/b43/ucode27_sslpn.fw
/lib/firmware/b43/ucode29_mimo.fw
/lib/firmware/b43/ucode30_mimo.fw
/lib/firmware/b43/ucode32_mimo.fw
/lib/firmware/b43/ucode33_lcn40.fw
/lib/firmware/b43/ucode5.fw
/lib/firmware/b43/ucode9.fw
atď
-
Díky, vše se mi zdá nainstalované..
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ sudo apt-get install linux-firmware-nonfree
[sudo] password for helena:
Čtu seznamy balíků… Hotovo
Vytvářím strom závislostí
Čtu stavové informace… Hotovo
linux-firmware-nonfree je již nejnovější verze.
Následující balík byl nainstalován automaticky a již není potřeba:
dkms
Pro jejich odstranění použijte „apt-get autoremove“.
0 aktualizováno, 0 nově instalováno, 0 k odstranění a 0 neaktualizováno.
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ sudo apt-get install firmware-b43-installer b43-fwcutter
Čtu seznamy balíků… Hotovo
Vytvářím strom závislostí
Čtu stavové informace… Hotovo
b43-fwcutter je již nejnovější verze.
firmware-b43-installer je již nejnovější verze.
Následující balík byl nainstalován automaticky a již není potřeba:
dkms
Pro jejich odstranění použijte „apt-get autoremove“.
0 aktualizováno, 0 nově instalováno, 0 k odstranění a 0 neaktualizováno.
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ sudo modprobe b43
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$
ale po restartu opět nic..
A jak najdu ten adresář?
-
vidím to na chybu na 95 % medzi klávesnicou a stoličkou ;)
Prosím Ťa, pošli ešte tieto výpisy:iwlist scan
iwconfig
ifconfig -a
nm-tool
ten adresár si naklikaj v súborovom manažeri ... alebo cez terminál cd /lib/firmware/b43
ls
-
Abychom nakonec nezjistily, že je tam pořád ten dodatečný ovladač.
-
Dobrý den,
vidím to na chybu na 95 % medzi klávesnicou a stoličkou
to je přece od začátku jasný :(.., možná i na 98,5%
ten adresár si naklikaj v súborovom manažeri ... alebo cez terminál
jen jsem se chtěla ujistit, že to hledám dobře, ale nic v těch souborech nevidím
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ cd /lib/firmware/b43
bash: cd: /lib/firmware/b43: Operace zamítnuta
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ ls
Dokumenty Hudba Plocha Šablony Videa
examples.desktop Obrázky Stažené Veřejné
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$
Tady jsou ty výpisy
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ ifconfig -a
eth0 Link encap:Ethernet HWadr 00:17:a4:da:99:38
inet adr:192.168.0.103 Všesměr:192.168.0.255 Maska:255.255.255.0
inet6-adr: fe80::217:a4ff:feda:9938/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:1641 errors:0 dropped:0 overruns:0 frame:0
TX packets:1269 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 1490906 (1.4 MB) Odesláno bajtů: 146220 (146.2 KB)
Přerušení:23
lo Link encap:Místní smyčka
inet adr:127.0.0.1 Maska:255.0.0.0
inet6-adr: ::1/128 Rozsah:Počítač
AKTIVOVÁNO SMYČKA BĚŽÍ MTU:65536 Metrika:1
RX packets:457 errors:0 dropped:0 overruns:0 frame:0
TX packets:457 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 35391 (35.3 KB) Odesláno bajtů: 35391 (35.3 KB)
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ nm-tool
Díky!!
-
Á. nedostatečná oprávnění. Tak nám sem pošlete
sudo ls /lib/firmware/b43
-
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ sudo ls /lib/firmware/b43
[sudo] password for helena:
a0g0bsinitvals5.fw lp0bsinitvals14.fw sslpn2bsinitvals17.fw
a0g0bsinitvals9.fw lp0bsinitvals15.fw sslpn2bsinitvals19.fw
a0g0initvals5.fw lp0bsinitvals16.fw sslpn2initvals17.fw
a0g0initvals9.fw lp0initvals13.fw sslpn2initvals19.fw
a0g1bsinitvals13.fw lp0initvals14.fw sslpn3bsinitvals21.fw
a0g1bsinitvals5.fw lp0initvals15.fw sslpn3initvals21.fw
a0g1bsinitvals9.fw lp0initvals16.fw sslpn4bsinitvals22.fw
a0g1initvals13.fw lp1bsinitvals20.fw sslpn4initvals22.fw
a0g1initvals5.fw lp1bsinitvals22.fw ucode11.fw
a0g1initvals9.fw lp1initvals20.fw ucode13.fw
b0g0bsinitvals13.fw lp1initvals22.fw ucode14.fw
b0g0bsinitvals5.fw lp2bsinitvals19.fw ucode15.fw
b0g0bsinitvals9.fw lp2initvals19.fw ucode16_lp.fw
b0g0initvals13.fw n0absinitvals11.fw ucode16_mimo.fw
b0g0initvals5.fw n0bsinitvals11.fw ucode16_sslpn.fw
b0g0initvals9.fw n0bsinitvals16.fw ucode16_sslpn_nobt.fw
ht0bsinitvals26.fw n0bsinitvals17.fw ucode17.fw
ht0bsinitvals29.fw n0bsinitvals22.fw ucode17_mimo.fw
ht0initvals26.fw n0bsinitvals24.fw ucode19.fw
ht0initvals29.fw n0bsinitvals25.fw ucode19_sslpn.fw
lcn0bsinitvals24.fw n0initvals11.fw ucode19_sslpn_nobt.fw
lcn0bsinitvals25.fw n0initvals16.fw ucode20.fw
lcn0bsinitvals26.fw n0initvals17.fw ucode20_sslpn.fw
lcn0initvals24.fw n0initvals22.fw ucode20_sslpn_nobt.fw
lcn0initvals25.fw n0initvals24.fw ucode21_sslpn.fw
lcn0initvals26.fw n0initvals25.fw ucode21_sslpn_nobt.fw
lcn1bsinitvals24.fw n1bsinitvals20.fw ucode22_mimo.fw
lcn1bsinitvals25.fw n1initvals20.fw ucode22_sslpn.fw
lcn1bsinitvals26.fw n16bsinitvals30.fw ucode24_lcn.fw
lcn1initvals24.fw n16initvals30.fw ucode24_mimo.fw
lcn1initvals25.fw n18bsinitvals32.fw ucode25_lcn.fw
lcn1initvals26.fw n18initvals32.fw ucode25_mimo.fw
lcn2bsinitvals24.fw n2bsinitvals19.fw ucode26_mimo.fw
lcn2bsinitvals25.fw n2initvals19.fw ucode27_sslpn.fw
lcn2bsinitvals26.fw pcm5.fw ucode29_mimo.fw
lcn2initvals24.fw sslpn0bsinitvals16.fw ucode30_mimo.fw
lcn2initvals25.fw sslpn0initvals16.fw ucode32_mimo.fw
lcn2initvals26.fw sslpn1bsinitvals20.fw ucode33_lcn40.fw
lcn400bsinitvals33.fw sslpn1bsinitvals27.fw ucode5.fw
lcn400initvals33.fw sslpn1initvals20.fw ucode9.fw
lp0bsinitvals13.fw sslpn1initvals27.fw
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$
-
firmware máš na správnom mieste, ale wifina nemá vytvorené žiadne sieťové rozhranie, ako keby wifi bola hardwerovo vypnutá , buď v biose, alebo blokovaná tlačítkom na notebooku. pomol by výpis:
rfkill list all
dmesg
lsmod | grep b43 ten druhý príkaz bude dlhý , ale veľa vecí napovie
-
Moc děkuju, že mi věnuješ čas.
Dlouhý to teda je..
Tlačítko na notebooku mačkám pořád jako divá, ale nesvítí a nesvítí. Pravda je, že jak to pořád vypínám a zapínám, tak se mi jednou přechodně objevilo po kliknutí na síť, že wifi je hardwarově blokovaná, nebo tak něco, ale teď to vůbec nic o wifi neříká, jakoby neexistovala.
[ 0.211517] pci_bus 0000:01: resource 0 [io 0x6000-0x6fff]
[ 0.211520] pci_bus 0000:01: resource 1 [mem 0xd4300000-0xd43fffff]
[ 0.211524] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xc7ffffff 64bit pref]
[ 0.211527] pci_bus 0000:10: resource 0 [io 0x4000-0x5fff]
[ 0.211531] pci_bus 0000:10: resource 1 [mem 0xd0000000-0xd3ffffff]
[ 0.211534] pci_bus 0000:20: resource 0 [io 0x2000-0x3fff]
[ 0.211537] pci_bus 0000:20: resource 1 [mem 0xcc000000-0xcfffffff]
[ 0.211541] pci_bus 0000:30: resource 1 [mem 0xc8000000-0xc80fffff]
[ 0.211544] pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
[ 0.211548] pci_bus 0000:02: resource 1 [mem 0xd4000000-0xd42fffff]
[ 0.211551] pci_bus 0000:02: resource 2 [mem 0x40000000-0x43ffffff pref]
[ 0.211554] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.211558] pci_bus 0000:02: resource 5 [mem 0x40000000-0xfcffffffff]
[ 0.211561] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.211564] pci_bus 0000:03: resource 0 [io 0x1000-0x10ff]
[ 0.211568] pci_bus 0000:03: resource 1 [io 0x1400-0x14ff]
[ 0.211571] pci_bus 0000:03: resource 2 [mem 0x40000000-0x43ffffff pref]
[ 0.211574] pci_bus 0000:03: resource 3 [mem 0x48000000-0x4bffffff]
[ 0.211624] NET: Registered protocol family 2
[ 0.211854] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.211906] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.211954] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.211954] TCP: reno registered
[ 0.211954] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.211954] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.211954] NET: Registered protocol family 1
[ 0.211954] pci 0000:00:00.0: MSI quirk detected; MSI disabled
[ 0.211954] pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled
[ 0.211954] pci 0000:01:05.0: Boot video device
[ 0.211954] PCI: CLS 64 bytes, default 64
[ 0.211954] Trying to unpack rootfs image as initramfs...
[ 0.689183] Freeing initrd memory: 16724K (f5f46000 - f6f9b000)
[ 0.689373] Scanning for low memory corruption every 60 seconds
[ 0.689702] Initialise module verification
[ 0.689769] audit: initializing netlink socket (disabled)
[ 0.689787] type=2000 audit(1397741272.687:1): initialized
[ 0.726343] bounce pool size: 64 pages
[ 0.726357] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.728890] zbud: loaded
[ 0.728960] VFS: Disk quotas dquot_6.5.2
[ 0.729028] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.729824] fuse init (API version 7.22)
[ 0.729946] msgmni has been set to 1739
[ 0.730391] Key type asymmetric registered
[ 0.730394] Asymmetric key parser 'x509' registered
[ 0.730452] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.730490] io scheduler noop registered
[ 0.730492] io scheduler deadline registered (default)
[ 0.730537] io scheduler cfq registered
[ 0.730807] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.730834] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.735405] ACPI: AC Adapter [C1C3] (on-line)
[ 0.735497] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0
[ 0.735504] ACPI: Sleep Button [C266]
[ 0.735563] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 0.735603] ACPI: Lid Switch [C267]
[ 0.735662] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.735666] ACPI: Power Button [PWRF]
[ 0.735764] ACPI: Fan [C364] (off)
[ 0.735822] ACPI: Fan [C365] (off)
[ 0.735882] ACPI: Fan [C366] (off)
[ 0.735938] ACPI: Fan [C367] (off)
[ 0.744398] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.744402] ACPI: Thermal Zone [TZ1] (36 C)
[ 0.748377] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.748380] ACPI: Thermal Zone [TZ2] (27 C)
[ 0.763502] thermal LNXTHERM:02: registered as thermal_zone2
[ 0.763505] ACPI: Thermal Zone [TZ3] (26 C)
[ 0.763581] GHES: HEST is not enabled!
[ 0.763705] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.765764] Linux agpgart interface v0.103
[ 0.767843] isapnp: Scanning for PnP cards...
[ 0.817970] brd: module loaded
[ 0.862979] loop: module loaded
[ 0.863090] megasas: 06.600.18.00-rc1 Wed. May. 15 17:00:00 PDT 2013
[ 0.863699] libphy: Fixed MDIO Bus: probed
[ 0.863876] tun: Universal TUN/TAP device driver, 1.6
[ 0.863878] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.863929] PPP generic driver version 2.4.2
[ 0.864051] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.864054] ehci-pci: EHCI PCI platform driver
[ 0.864249] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 0.864258] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 1
[ 0.864338] ehci-pci 0000:00:13.2: irq 19, io mem 0xd4403000
[ 0.908401] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 0.908492] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.908495] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.908498] usb usb1: Product: EHCI Host Controller
[ 0.908501] usb usb1: Manufacturer: Linux 3.11.0-19-generic ehci_hcd
[ 0.908504] usb usb1: SerialNumber: 0000:00:13.2
[ 0.908645] hub 1-0:1.0: USB hub found
[ 0.908651] hub 1-0:1.0: 8 ports detected
[ 0.909039] ehci-platform: EHCI generic platform driver
[ 0.909054] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.909056] ohci-pci: OHCI PCI platform driver
[ 0.909196] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 0.909204] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2
[ 0.909223] ohci-pci 0000:00:13.0: irq 19, io mem 0xd4401000
[ 1.088170] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.088173] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.088176] usb usb2: Product: OHCI PCI host controller
[ 1.088179] usb usb2: Manufacturer: Linux 3.11.0-19-generic ohci_hcd
[ 1.088182] usb usb2: SerialNumber: 0000:00:13.0
[ 1.088310] hub 2-0:1.0: USB hub found
[ 1.088319] hub 2-0:1.0: 4 ports detected
[ 1.088643] ohci-pci 0000:00:13.1: OHCI PCI host controller
[ 1.088653] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 3
[ 1.088672] ohci-pci 0000:00:13.1: irq 19, io mem 0xd4402000
[ 1.132707] isapnp: No Plug & Play device found
[ 1.148068] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.148101] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.148104] usb usb3: Product: OHCI PCI host controller
[ 1.148107] usb usb3: Manufacturer: Linux 3.11.0-19-generic ohci_hcd
[ 1.148110] usb usb3: SerialNumber: 0000:00:13.1
[ 1.148231] hub 3-0:1.0: USB hub found
[ 1.148243] hub 3-0:1.0: 4 ports detected
[ 1.148427] ohci-platform: OHCI generic platform driver
[ 1.148441] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.148549] i8042: PNP: PS/2 Controller [PNP0303:C21E,PNP0f13:C21F] at 0x60,0x64 irq 1,12
[ 1.150196] i8042: Detected active multiplexing controller, rev 1.1
[ 1.151915] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.151922] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.151961] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.151990] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.152091] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.152268] mousedev: PS/2 mouse device common for all mice
[ 1.152464] rtc_cmos 00:06: RTC can wake from S4
[ 1.152651] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.152684] rtc_cmos 00:06: alarms up to one month, y3k, 114 bytes nvram
[ 1.152784] device-mapper: uevent: version 1.0.3
[ 1.152859] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[ 1.152955] platform eisa.0: Probing EISA bus 0
[ 1.152959] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 1.152963] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 1.152967] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 1.152970] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 1.152974] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 1.152977] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 1.152981] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 1.152984] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 1.152988] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 1.152991] platform eisa.0: EISA: Detected 0 cards
[ 1.153001] cpufreq-nforce2: No nForce2 chipset.
[ 1.153005] cpuidle: using governor ladder
[ 1.153007] cpuidle: using governor menu
[ 1.153022] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.153143] TCP: cubic registered
[ 1.153362] NET: Registered protocol family 10
[ 1.153603] NET: Registered protocol family 17
[ 1.153619] Key type dns_resolver registered
[ 1.153794] Using IPI No-Shortcut mode
[ 1.153900] PM: Hibernation image not present or could not be loaded.
[ 1.153906] Loading module verification certificates
[ 1.159307] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: ca1b055db3ec8cb1ca2747acb5e7f809ae1841c4'
[ 1.159348] registered taskstats version 1
[ 1.162284] Key type trusted registered
[ 1.165113] Key type encrypted registered
[ 1.167876] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.168337] Magic number: 10:568:483
[ 1.168519] rtc_cmos 00:06: setting system clock to 2014-04-17 13:27:53 UTC (1397741273)
[ 1.168701] powernow-k8: fid 0xa (1800 MHz), vid 0xe
[ 1.168704] powernow-k8: fid 0x8 (1600 MHz), vid 0x10
[ 1.168707] powernow-k8: fid 0x0 (800 MHz), vid 0x18
[ 1.168737] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 3500+ (1 cpu cores) (version 2.20.00)
[ 1.168745] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.168746] EDD information not available.
[ 1.169604] ACPI: Battery Slot [C1C5] (battery present)
[ 1.169705] ACPI: Battery Slot [C1C4] (battery absent)
[ 1.170331] Freeing unused kernel memory: 900K (c1a7e000 - c1b5f000)
[ 1.170385] Write protecting the kernel text: 6684k
[ 1.170493] Write protecting the kernel read-only data: 3444k
[ 1.170495] NX-protecting the kernel data: 5604k
[ 1.177387] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.194352] udevd[92]: starting version 175
[ 1.502139] sata_sil 0000:00:12.0: version 2.4
[ 1.502147] sata_sil 0000:00:12.0: quirky BIOS, skipping spindown on poweroff and hibernation
[ 1.505753] scsi0 : sata_sil
[ 1.509643] scsi1 : sata_sil
[ 1.509763] ata1: SATA max UDMA/100 mmio m512@0xd4409000 tf 0xd4409080 irq 16
[ 1.509768] ata2: SATA max UDMA/100 mmio m512@0xd4409000 tf 0xd44090c0 irq 16
[ 1.511783] pps_core: LinuxPPS API ver. 1 registered
[ 1.511788] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.512738] scsi2 : pata_atiixp
[ 1.515503] scsi3 : pata_atiixp
[ 1.515834] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x7040 irq 14
[ 1.515838] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x7048 irq 15
[ 1.530736] sdhci: Secure Digital Host Controller Interface driver
[ 1.530740] sdhci: Copyright(c) Pierre Ossman
[ 1.542682] sdhci-pci 0000:02:04.3: SDHCI controller found [104c:803c] (rev 0)
[ 1.542816] mmc0: no vqmmc regulator found
[ 1.542819] mmc0: no vmmc regulator found
[ 1.544777] PTP clock support registered
[ 1.555340] mmc0: SDHCI controller on PCI [0000:02:04.3] using PIO
[ 1.648085] firewire_ohci 0000:02:04.1: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
[ 1.648472] tg3.c:v3.132 (May 21, 2013)
[ 1.685181] tg3 0000:02:01.0 eth0: Tigon3 [partno(BCM95788A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:17:a4:da:99:38
[ 1.685188] tg3 0000:02:01.0 eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0])
[ 1.685192] tg3 0000:02:01.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.685196] tg3 0000:02:01.0 eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[ 1.708905] ata3.00: ATAPI: PIONEER DVDRW DVR-K17, 1.05, max MWDMA2
[ 1.712033] usb 3-1: new full-speed USB device number 2 using ohci-pci
[ 1.740830] ata3.00: configured for MWDMA2
[ 1.828067] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.836326] ata1.00: ATA-7: FUJITSU MHV2080BH PL, 892C, max UDMA/100
[ 1.836330] ata1.00: 156301488 sectors, multi 16: LBA48
[ 1.852332] ata1.00: configured for UDMA/100
[ 1.852476] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
[ 1.852893] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.852970] sd 0:0:0:0: [sda] Write Protect is off
[ 1.852975] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.853008] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.853556] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.911100] sda: sda1 sda2 < sda5 >
[ 1.911599] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.917078] usb 3-1: New USB device found, idVendor=08ff, idProduct=2580
[ 1.917082] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.917085] usb 3-1: Product: Fingerprint Sensor
[ 2.148140] firewire_core 0000:02:04.1: created device fw0: GUID 00023f9929651a0e, S400
[ 2.172051] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.181481] scsi 2:0:0:0: CD-ROM PIONEER DVDRW DVR-K17 1.05 PQ: 0 ANSI: 5
[ 2.193392] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.193395] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.193537] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 2.193695] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 2.529699] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.923507] init: ureadahead main process (287) terminated with status 5
[ 5.075756] Adding 915452k swap on /dev/sda5. Priority:-1 extents:1 across:915452k FS
[ 6.212571] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.560467] udevd[361]: starting version 175
[ 8.014506] lp: driver loaded but no devices found
[ 8.212378] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 8.792252] parport_pc 00:01: [io 0x0378-0x037f]
[ 8.792262] parport_pc 00:01: [io 0x0778-0x077a]
[ 8.792354] parport_pc 00:01: [irq 7]
[ 8.792359] parport_pc 00:01: [dma 1]
[ 8.793640] parport_pc 00:01: activated
[ 8.793645] parport_pc 00:01: reported by Plug and Play ACPI
[ 8.804945] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 8.892249] lp0: using parport0 (interrupt-driven).
[ 9.001484] tpm_tis 00:02: 1.2 TPM (device-id 0xB, rev-id 16)
[ 9.028198] wmi: Mapper loaded
[ 9.105203] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 9.105332] [Firmware Bug]: _BCQ is used instead of _BQC
[ 9.120163] tpm_tis 00:02: Adjusting TPM timeout parameters.
[ 9.141308] acpi device:03: registered as cooling_device5
[ 9.141392] ACPI: Video Device [C07B] (multi-head: yes rom: no post: no)
[ 9.142635] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/LNXVIDEO:00/input/input4
[ 9.194133] ppdev: user-space parallel port driver
[ 9.376513] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 9.556906] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.561633] yenta_cardbus 0000:02:04.0: CardBus bridge found [103c:30b0]
[ 9.561663] yenta_cardbus 0000:02:04.0: Enabling burst memory read transactions
[ 9.561670] yenta_cardbus 0000:02:04.0: Using INTVAL to route CSC interrupts to PCI
[ 9.561673] yenta_cardbus 0000:02:04.0: Routing CardBus interrupts to PCI
[ 9.561681] yenta_cardbus 0000:02:04.0: TI: mfunc 0x01a11002, devctl 0x64
[ 9.668564] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8200, revision 0
[ 9.785451] input: HP WMI hotkeys as /devices/virtual/input/input5
[ 9.821049] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0c78, PCI irq 20
[ 9.821057] yenta_cardbus 0000:02:04.0: Socket status: 30000006
[ 9.821062] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 9.821074] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [io 0x1000-0x1fff]
[ 9.821078] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x1000-0x1fff:
[ 9.822900] excluding 0x1000-0x10ff 0x1400-0x14ff
[ 9.834914] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [mem 0xd4000000-0xd42fffff]
[ 9.834921] pcmcia_socket pcmcia_socket0: cs: memory probe 0xd4000000-0xd42fffff:
[ 9.834925] excluding 0xd4000000-0xd402ffff
[ 9.834937] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [mem 0x40000000-0x43ffffff pref]
[ 9.834941] pcmcia_socket pcmcia_socket0: cs: memory probe 0x40000000-0x43ffffff:
[ 9.834951] excluding 0x40000000-0x43ffffff
[ 9.944077] tpm_tis 00:02: TPM is disabled/deactivated (0x7)
[ 10.512899] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[ 10.514371] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 10.515379] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[ 10.515887] excluding 0x3f0-0x3f7 0x408-0x40f 0x4d0-0x4d7
[ 10.516396] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[ 10.517281] clean.
[ 10.517302] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[ 10.517666] excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
[ 10.518056] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[ 10.518066] excluding 0xc0000-0xfffff
[ 10.518086] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[ 10.518097] clean.
[ 10.518115] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[ 10.518126] clean.
[ 10.518144] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[ 10.519071] clean.
[ 10.543859] psmouse serio4: synaptics: Touchpad model: 1, fw: 6.2, id: 0x2580b1, caps: 0xa04793/0x300000/0x0, board id: 71, fw id: 240405
[ 10.543871] psmouse serio4: synaptics: serio: Synaptics pass-through port at isa0060/serio4/input0
[ 10.591554] [drm] Initialized drm 1.1.0 20060810
[ 10.613022] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input6
[ 11.609265] hda-intel 0000:00:14.2: Using LPIB position fix
[ 11.612816] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[ 11.716929] autoconfig: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[ 11.716945] speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 11.716948] hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 11.716950] mono: mono_out=0x0
[ 11.716951] inputs:
[ 11.950353] [drm] radeon kernel modesetting enabled.
[ 11.951007] [drm] initializing kernel modesetting (RS480 0x1002:0x5975 0x103C:0x30B0).
[ 11.951030] [drm] register mmio base: 0xD4300000
[ 11.951033] [drm] register mmio size: 65536
[ 11.951143] [drm] Generation 2 PCI interface, using max accessible memory
[ 11.951151] radeon 0000:01:05.0: VRAM: 128M 0x0000000038000000 - 0x000000003FFFFFFF (128M used)
[ 11.951155] radeon 0000:01:05.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF
[ 11.951283] [drm] Detected VRAM RAM=128M, BAR=128M
[ 11.951286] [drm] RAM width 128bits DDR
[ 11.951729] [TTM] Zone kernel: Available graphics memory: 445638 kiB
[ 11.951732] [TTM] Zone highmem: Available graphics memory: 447594 kiB
[ 11.951734] [TTM] Initializing pool allocator
[ 11.951740] [TTM] Initializing DMA pool allocator
[ 11.951770] [drm] radeon: 128M of VRAM memory ready
[ 11.951772] [drm] radeon: 512M of GTT memory ready.
[ 11.951787] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 11.959611] [drm] radeon: 2 quad pipes, 1 z pipes initialized.
[ 11.965553] [drm] PCIE GART of 512M enabled (table at 0x0000000034080000).
[ 11.965608] radeon 0000:01:05.0: WB enabled
[ 11.965614] radeon 0000:01:05.0: fence driver on ring 0 use gpu addr 0x0000000040000000 and cpu addr 0xf517d000
[ 11.965618] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 11.965620] [drm] Driver supports precise vblank timestamp query.
[ 11.965654] [drm] radeon: irq initialized.
[ 11.965668] [drm] Loading R300 Microcode
[ 12.433920] [drm] radeon: ring at 0x0000000040001000
[ 12.433945] [drm] ring test succeeded in 1 usecs
[ 12.434101] [drm] ib test succeeded in 0 usecs
[ 12.434905] [drm] Panel ID String: QDS
[ 12.434908] [drm] Panel Size 1024x768
[ 12.459316] [drm] radeon legacy LVDS backlight initialized
[ 12.459319] [drm] Radeon Display Connectors
[ 12.459321] [drm] Connector 0:
[ 12.459323] [drm] VGA-1
[ 12.459326] [drm] DDC: 0x68 0x68 0x68 0x68 0x68 0x68 0x68 0x68
[ 12.459328] [drm] Encoders:
[ 12.459330] [drm] CRT1: INTERNAL_DAC2
[ 12.459331] [drm] Connector 1:
[ 12.459333] [drm] LVDS-1
[ 12.459336] [drm] DDC: 0x198 0x198 0x19c 0x19c 0x1a0 0x1a0 0x1a4 0x1a4
[ 12.459338] [drm] Encoders:
[ 12.459339] [drm] LCD1: INTERNAL_LVDS
[ 12.459341] [drm] Connector 2:
[ 12.459343] [drm] SVIDEO-1
[ 12.459344] [drm] Encoders:
[ 12.459346] [drm] TV1: INTERNAL_DAC2
[ 12.459412] [drm] radeon: power management initialized
[ 12.529777] [drm] fb mappable at 0xC0040000
[ 12.529783] [drm] vram apper at 0xC0000000
[ 12.529785] [drm] size 3145728
[ 12.529786] [drm] fb depth is 24
[ 12.529788] [drm] pitch is 4096
[ 12.530036] fbcon: radeondrmfb (fb0) is primary device
[ 12.568528] Console: switching to colour frame buffer device 128x48
[ 12.575699] radeon 0000:01:05.0: fb0: radeondrmfb frame buffer device
[ 12.575702] radeon 0000:01:05.0: registered panic notifier
[ 12.575718] [drm] Initialized radeon 2.34.0 20080528 for 0000:01:05.0 on minor 0
[ 12.902461] type=1400 audit(1397741285.231:2): apparmor="STATUS" operation="profile_load" parent=671 profile="unconfined" name="/sbin/dhclient" pid=692 comm="apparmor_parser"
[ 12.902473] type=1400 audit(1397741285.231:3): apparmor="STATUS" operation="profile_load" parent=671 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=692 comm="apparmor_parser"
[ 12.902481] type=1400 audit(1397741285.231:4): apparmor="STATUS" operation="profile_load" parent=671 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=692 comm="apparmor_parser"
[ 12.903325] type=1400 audit(1397741285.231:5): apparmor="STATUS" operation="profile_replace" parent=671 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=692 comm="apparmor_parser"
[ 12.903334] type=1400 audit(1397741285.231:6): apparmor="STATUS" operation="profile_replace" parent=671 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=692 comm="apparmor_parser"
[ 12.903782] type=1400 audit(1397741285.231:7): apparmor="STATUS" operation="profile_replace" parent=671 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=692 comm="apparmor_parser"
[ 12.904822] type=1400 audit(1397741285.231:8): apparmor="STATUS" operation="profile_replace" parent=689 profile="unconfined" name="/sbin/dhclient" pid=693 comm="apparmor_parser"
[ 12.904832] type=1400 audit(1397741285.231:9): apparmor="STATUS" operation="profile_replace" parent=689 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser"
[ 12.904839] type=1400 audit(1397741285.231:10): apparmor="STATUS" operation="profile_replace" parent=689 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser"
[ 12.905701] type=1400 audit(1397741285.231:11): apparmor="STATUS" operation="profile_replace" parent=689 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser"
[ 14.079447] init: failsafe main process (791) killed by TERM signal
[ 17.005553] Bluetooth: Core ver 2.16
[ 17.005641] NET: Registered protocol family 31
[ 17.005644] Bluetooth: HCI device and connection manager initialized
[ 17.006575] Bluetooth: HCI socket layer initialized
[ 17.006584] Bluetooth: L2CAP socket layer initialized
[ 17.006595] Bluetooth: SCO socket layer initialized
[ 17.162174] Bluetooth: RFCOMM TTY layer initialized
[ 17.162192] Bluetooth: RFCOMM socket layer initialized
[ 17.162195] Bluetooth: RFCOMM ver 1.11
[ 17.351704] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.351711] Bluetooth: BNEP filters: protocol multicast
[ 17.351726] Bluetooth: BNEP socket layer initialized
[ 20.244749] audit_printk_skb: 15 callbacks suppressed
[ 20.244756] type=1400 audit(1397741292.571:17): apparmor="STATUS" operation="profile_load" parent=949 profile="unconfined" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=955 comm="apparmor_parser"
[ 20.244766] type=1400 audit(1397741292.571:18): apparmor="STATUS" operation="profile_load" parent=949 profile="unconfined" name="chromium_browser" pid=955 comm="apparmor_parser"
[ 20.245415] type=1400 audit(1397741292.571:19): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="chromium_browser" pid=955 comm="apparmor_parser"
[ 20.250455] type=1400 audit(1397741292.575:20): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="/sbin/dhclient" pid=956 comm="apparmor_parser"
[ 20.250471] type=1400 audit(1397741292.575:21): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=956 comm="apparmor_parser"
[ 20.250479] type=1400 audit(1397741292.575:22): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=956 comm="apparmor_parser"
[ 20.251328] type=1400 audit(1397741292.575:23): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=956 comm="apparmor_parser"
[ 20.251335] type=1400 audit(1397741292.575:24): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=956 comm="apparmor_parser"
[ 20.251784] type=1400 audit(1397741292.575:25): apparmor="STATUS" operation="profile_replace" parent=949 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=956 comm="apparmor_parser"
[ 20.677559] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.678626] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.754471] type=1400 audit(1397741293.079:26): apparmor="STATUS" operation="profile_load" parent=949 profile="unconfined" name="/usr/bin/evince" pid=957 comm="apparmor_parser"
[ 22.254661] tg3 0000:02:01.0 eth0: Link is up at 100 Mbps, full duplex
[ 22.254674] tg3 0000:02:01.0 eth0: Flow control is on for TX and on for RX
[ 22.254696] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 51.432071] usb 2-3: new low-speed USB device number 2 using ohci-pci
[ 51.648128] usb 2-3: New USB device found, idVendor=0458, idProduct=0046
[ 51.648135] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 51.648140] usb 2-3: Product: Wireless Mouse
[ 51.648143] usb 2-3: Manufacturer: Genius
[ 51.800144] hidraw: raw HID events driver (C) Jiri Kosina
[ 51.918868] usbcore: registered new interface driver usbhid
[ 51.918875] usbhid: USB HID core driver
[ 52.008956] input: Genius Wireless Mouse as /devices/pci0000:00/0000:00:13.0/usb2/2-3/2-3:1.0/input/input7
[ 52.009319] hid-generic 0003:0458:0046.0001: input,hidraw0: USB HID v1.10 Mouse [Genius Wireless Mouse] on usb-0000:00:13.0-3/input0
[ 58.323577] audit_printk_skb: 126 callbacks suppressed
[ 58.323589] type=1400 audit(1397741331.647:69): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/mission-control-5" name="/usr/share/gvfs/remote-volume-monitors/" pid=1982 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 68.179340] tg3 0000:02:01.0 eth0: Link is down
[ 72.107875] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 85.421603] tg3 0000:02:01.0 eth0: Link is up at 100 Mbps, full duplex
[ 85.421620] tg3 0000:02:01.0 eth0: Flow control is on for TX and on for RX
[ 85.421673] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
helena@helena-HP-Compaq-nx6325-EY352EA-AKB:~$ lsmod | grep b43