Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Internet a sítě => Téma založeno: davoss1 25 Prosince 2014, 23:23:15
-
Pěkný večer.Už několik dní se zoufale snažím rozběhat wifi na notebooku.Přečetl jsem toho tuny.Sítová karta je:Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07).Zkoušel jsem i přechod z verze 12.04 na vyšší,ale nic.Ovladače taky nic.Při těchto pokusech to psalo něco chyba s gmail a gmail run.Už fakt nevím.Přes kabel mi net valí a přes modem od t- mobilu taky.Nahoře vpravo po kliknutí na ikonu sítí to píše u bezdrátové-zařízení není připraveno(chybí firmware).To už jsem se taky snažil najít.Prostě nic.Bluetooth taky zmizel.Mám notas HP 255 G1.Ještě rok v záruce.Než ho půjdu reklamovat,zkusil jsem naposled aspon tohle.Moc díky za případnou rad a pomoc.
-
tak ukaž co to píše!
-
Ted jsem hrabal zase v něčem a píše tohle...
eth0 Link encap:Ethernet HWadr a0:48:1c:ed:5c:4e
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST MTU:1500 Metrika:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)
lo Link encap:Místní smyčka
inet adr:127.0.0.1 Maska:255.0.0.0
inet6-adr: ::1/128 Rozsah:Počítač
AKTIVOVÁNO SMYČKA BĚŽÍ MTU:16436 Metrika:1
RX packets:5380 errors:0 dropped:0 overruns:0 frame:0
TX packets:5380 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 550149 (550.1 KB) Odesláno bajtů: 550149 (550.1 KB)
ppp0 Link encap:Point-to-Point Protokol
inet adr:10.84.244.34 P-t-P:10.64.64.64 Maska:255.255.255.255
AKTIVOVÁNO POINTOPOINT BĚŽÍ NEARP MULTICAST MTU:1500 Metrika:1
RX packets:48796 errors:0 dropped:0 overruns:0 frame:0
TX packets:40758 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:3
Přijato bajtů: 41198908 (41.1 MB) Odesláno bajtů: 6270491 (6.2 MB)
wlan0 Link encap:Ethernet HWadr 70:18:8b:d9:1e:85
VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST MTU:1500 Metrika:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)
davoss@davoss-HP-255-G1-Notebook-PC:~$ iwconfig
ppp0 no wireless extensions.
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
-
Dej sem část dmesg s řádkama od wifi a případně s žádostí o ten firmware.
Jinak někde na abclinuxu jsem četl, že mže být problém s wifi u současného připojení ethernetu. Proto taky pak mžeš zkusit vypojit kabel nebo deaktivovat eth.
-
Předem děkuju za bleskovou reakci.Nejsem PC odborník,ale snad třeba tohle něco vysvětlí.Dík.....
firmware: příkaz nebyl nalezen
davoss@davoss-HP-255-G1-Notebook-PC:~$ sudo apt-get install firmware-b43-lpphy-installer
[sudo] password for davoss:
Čtu seznamy balíků… Hotovo
Vytvářím strom závislostí
Čtu stavové informace… Hotovo
Následující balíky byly nainstalovány automaticky a již nejsou potřeba:
execstack kde-l10n-cs libxml-parser-perl gdisk cdbs libelfg0 intltool
language-pack-kde-cs-base python-scour language-pack-kde-cs
language-pack-kde-en kde-l10n-engb compiz-plugins foo2zjs dpkg-repack
dh-modaliases python-support dh-translations python-progressbar
language-pack-kde-en-base
Pro jejich odstranění použijte „apt-get autoremove“.
Následující balíky budou ODSTRANĚNY:
firmware-b43-installer
Následující NOVÉ balíky budou nainstalovány:
firmware-b43-lpphy-installer
0 aktualizováno, 1 nově instalováno, 1 k odstranění a 0 neaktualizováno.
2 instalováno nebo odstraněno pouze částečně.
Potřebuji stáhnout 3 390 B archivů.
Po této operaci bude na disku uvolněno 1 024 B.
Chcete pokračovat [Y/n]? y
Mám:1 http://archive.ubuntu.com/ubuntu/ precise/multiverse firmware-b43-lpphy-installer all 1:015-9 [3 390 B]
Staženo 3 390 B za 0s (6 770 B/s)
(Čtu databázi … nyní je nainstalováno 452773 souborů a adresářů.)
Odinstalování balíku firmware-b43-installer …
Vybírám dosud nevybraný balík firmware-b43-lpphy-installer.
(Čtu databázi … nyní je nainstalováno 452770 souborů a adresářů.)
Rozbaluji firmware-b43-lpphy-installer (z …/firmware-b43-lpphy-installer_1%3a015-9_all.deb) …
Nastavuji balík qmail (1.06-4) …
The hostname -f command returned: $1
Your system needs to have a fully qualified domain name (fqdn) in
order to install the var-qmail packages.
Installation aborted.
dpkg: chyba při zpracovávání qmail (--configure):
podproces instalovaný post-installation skript vrátil chybový status 1
Žádné apport hlášení nebylo vytvořeno, protože již byl dosažen MaxReports
dpkg: nesplněné závislosti zamezily konfiguraci balíku qmail-run:
qmail-run závisí na qmail (>= 1.06-2.1); avšak:
Balík qmail zatím není zkonfigurován.
dpkg: chyba při zpracovávání qmail-run (--configure):
problém se závislostmi - nechávám nezkonfigurované
Žádné apport hlášení nebylo vytvořeno, protože již byl dosažen MaxReports
Nastavuji balík firmware-b43-lpphy-installer (1:015-9) …
No chroot environment found. Starting normal installation
No supported card found.
Use proper b43 or b43legacy firmware.
Aborting.
Při zpracování nastaly chyby:
qmail
qmail-run
E: Sub-process /usr/bin/dpkg returned an error code (1)
-
Ten výpis smaž, a místo toho dej výpis dmesg a obal to tagem #.
-
Tak napřed pěkně dlouhý výpis a ted už skoro nic.Nebudu dělat frajera,tohle je asi větší problém.Možná se to dá nějak takhle na dálku.Každopádně díky za pomoc.Přeju dobrou noc.
-
Vypni na laptopu čudlík který deaktivuje wifi+bt pak zase zapni a dej výpis dmesg prostě když nevím jak to vypadá nebudu radit s instalací nějakým ovladačem když nemžu vědět jestli to k něčemu bude.
Jinak http://community.linuxmint.com/tutorial/view/218 ale není to současné ubuntu.
-
Pěkný den.Tak to tlačítko vypínání vůbec nereaguje.a výpis je tento:
width channel with regulatory rule:
[ 19.382982] cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 19.382986] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 19.382990] cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 19.382993] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 19.382997] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
[ 19.391181] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 19.402076] Registered led device: rt2800pci-phy0::radio
[ 19.402165] Registered led device: rt2800pci-phy0::assoc
[ 19.402254] Registered led device: rt2800pci-phy0::quality
[ 19.403454] lib80211: common routines for IEEE802.11 drivers
[ 19.403463] lib80211_crypt: registered algorithm 'NULL'
[ 19.417570] wl: disagrees about version of symbol cfg80211_scan_done
[ 19.417584] wl: Unknown symbol cfg80211_scan_done (err -22)
[ 19.417662] wl: disagrees about version of symbol cfg80211_disconnected
[ 19.417666] wl: Unknown symbol cfg80211_disconnected (err -22)
[ 19.417715] wl: disagrees about version of symbol wiphy_register
[ 19.417718] wl: Unknown symbol wiphy_register (err -22)
[ 19.417735] wl: disagrees about version of symbol wiphy_new
[ 19.417739] wl: Unknown symbol wiphy_new (err -22)
[ 19.417754] wl: disagrees about version of symbol cfg80211_put_bss
[ 19.417758] wl: Unknown symbol cfg80211_put_bss (err -22)
[ 19.417772] wl: disagrees about version of symbol cfg80211_roamed
[ 19.417775] wl: Unknown symbol cfg80211_roamed (err -22)
[ 19.417808] wl: disagrees about version of symbol cfg80211_ibss_joined
[ 19.417811] wl: Unknown symbol cfg80211_ibss_joined (err -22)
[ 19.417835] wl: disagrees about version of symbol cfg80211_michael_mic_failure
[ 19.417839] wl: Unknown symbol cfg80211_michael_mic_failure (err -22)
[ 19.417853] wl: disagrees about version of symbol cfg80211_connect_result
[ 19.417856] wl: Unknown symbol cfg80211_connect_result (err -22)
[ 19.417887] wl: disagrees about version of symbol wiphy_unregister
[ 19.417891] wl: Unknown symbol wiphy_unregister (err -22)
[ 19.417913] wl: disagrees about version of symbol cfg80211_get_bss
[ 19.417916] wl: Unknown symbol cfg80211_get_bss (err -22)
[ 19.417936] wl: disagrees about version of symbol __ieee80211_get_channel
[ 19.417940] wl: Unknown symbol __ieee80211_get_channel (err -22)
[ 19.417984] wl: disagrees about version of symbol ieee80211_channel_to_frequency
[ 19.417987] wl: Unknown symbol ieee80211_channel_to_frequency (err -22)
[ 19.418013] wl: disagrees about version of symbol cfg80211_inform_bss_frame
[ 19.418017] wl: Unknown symbol cfg80211_inform_bss_frame (err -22)
[ 19.418059] wl: disagrees about version of symbol wiphy_free
[ 19.418063] wl: Unknown symbol wiphy_free (err -22)
[ 19.450199] microcode: CPU0: patch_level=0x0500010d
[ 19.823317] type=1400 audit(1419584856.635:7): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=596 comm="cupsd" pid=596 comm="cupsd" capability=36 capname="block_suspend"
[ 19.877261] init: failsafe main process (716) killed by TERM signal
[ 20.035031] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xf00173/0x240000/0xa2400
[ 20.068178] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9
[ 20.082047] type=1400 audit(1419584856.895:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=896 comm="apparmor_parser"
[ 20.091312] type=1400 audit(1419584856.903:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=897 comm="apparmor_parser"
[ 20.092844] type=1400 audit(1419584856.907:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=896 comm="apparmor_parser"
[ 20.093048] type=1400 audit(1419584856.907:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=897 comm="apparmor_parser"
[ 20.705882] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705894] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705899] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705904] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705908] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705912] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705916] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705920] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705924] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705928] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705931] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705935] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705939] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705942] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705946] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705950] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705953] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705957] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705960] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705964] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705968] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705971] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.705975] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705979] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.705983] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705986] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.705990] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 20.705994] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.705999] cfg80211: World regulatory domain updated:
[ 20.706002] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 20.706006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.706009] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.706013] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.706017] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.706020] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.711793] microcode: CPU1: patch_level=0x0500010d
[ 20.763356] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 20.807942] kvm: disabled by bios
[ 20.828848] r8169 0000:03:00.0: eth0: link down
[ 20.829428] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.830251] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.843593] input: HP WMI hotkeys as /devices/virtual/input/input10
[ 20.882249] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 20.882600] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.910933] kvm: disabled by bios
[ 20.929809] usb 1-2: USB disconnect, device number 2
[ 21.282546] vesafb: mode is 1366x768x32, linelength=5632, pages=0
[ 21.282557] vesafb: scrolling: redraw
[ 21.282563] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[ 21.286006] vesafb: framebuffer at 0x80000000, mapped to 0xffffc90004b80000, using 4224k, total 4224k
[ 21.286429] Console: switching to colour frame buffer device 170x48
[ 21.286485] fb0: VESA VGA frame buffer device
[ 21.400188] init: anti-failure-late main process (1364) terminated with status 127
[ 23.057691] fglrx_pci 0000:00:01.0: irq 45 for MSI/MSI-X
[ 23.059552] [fglrx] Firegl kernel thread PID: 1467
[ 23.059728] [fglrx] Firegl kernel thread PID: 1468
[ 23.060257] [fglrx] Firegl kernel thread PID: 1469
[ 23.060500] [fglrx] IRQ 45 Enabled
[ 23.065934] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 23.065940] [fglrx] Reserved FB block: Unshared offset:fe36000, size:2000
[ 23.065945] [fglrx] Reserved FB block: Unshared offset:fe38000, size:1c8000
[ 23.065949] [fglrx] Reserved FB block: Unshared offset:17fee000, size:12000
[ 23.165602] [fglrx] ATIF platform detected with notification ID: 0xd0
[ 25.627023] usb 1-2: new high-speed USB device number 3 using ehci_hcd
[ 25.761636] usb 1-2: New USB device found, idVendor=12d1, idProduct=1506
[ 25.761653] usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[ 25.761663] usb 1-2: Product: HUAWEI Mobile
[ 25.761672] usb 1-2: Manufacturer: HUAWEI
[ 25.765175] scsi4 : usb-storage 1-2:1.4
[ 25.765636] scsi5 : usb-storage 1-2:1.5
[ 25.774680] init: plymouth-upstart-bridge main process (545) killed by TERM signal
[ 25.842515] usbcore: registered new interface driver usbserial
[ 25.842548] usbcore: registered new interface driver usbserial_generic
[ 25.842582] USB Serial support registered for generic
[ 25.842591] usbserial: USB Serial Driver core
[ 25.870636] usbcore: registered new interface driver option
[ 25.871236] USB Serial support registered for GSM modem (1-port)
[ 25.871812] option 1-2:1.0: GSM modem (1-port) converter detected
[ 25.873814] usb 1-2: GSM modem (1-port) converter now attached to ttyUSB0
[ 25.873907] option 1-2:1.2: GSM modem (1-port) converter detected
[ 25.874320] usb 1-2: GSM modem (1-port) converter now attached to ttyUSB1
[ 25.874358] option 1-2:1.3: GSM modem (1-port) converter detected
[ 25.875530] usb 1-2: GSM modem (1-port) converter now attached to ttyUSB2
[ 26.768427] scsi 5:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 26.770858] scsi 4:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 26.776219] sr1: scsi-1 drive
[ 26.777174] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 26.779033] sr 4:0:0:0: Attached scsi generic sg2 type 5
[ 26.779537] sd 5:0:0:0: Attached scsi generic sg3 type 0
[ 26.781348] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 327.853178] init: keep-brightness-boot main process (1968) terminated with status 127
[ 331.621525] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 331.648796] ISOFS: changing to secondary root
[ 332.088455] audit_printk_skb: 42 callbacks suppressed
[ 332.088465] type=1400 audit(1419585168.971:26): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=596 comm="cupsd" pid=596 comm="cupsd" capability=36 capname="block_suspend"
[ 378.254663] usb 1-3: new high-speed USB device number 4 using ehci_hcd
[ 378.441260] usb 1-3: New USB device found, idVendor=0979, idProduct=0371
[ 378.441277] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 378.441287] usb 1-3: Product: USB 2.0 Device
[ 378.441296] usb 1-3: Manufacturer: Jeilin
[ 378.441304] usb 1-3: SerialNumber: JL2007BV2000
[ 378.451108] scsi6 : usb-storage 1-3:1.0
[ 379.488871] scsi 6:0:0:0: Direct-Access General USB FLASH Drive 1.00 PQ: 0 ANSI: 0 CCS
[ 379.492742] sd 6:0:0:0: Attached scsi generic sg4 type 0
[ 379.500039] sd 6:0:0:0: [sdc] 237568 512-byte logical blocks: (121 MB/116 MiB)
[ 379.505699] sd 6:0:0:0: [sdc] Write Protect is off
[ 379.505720] sd 6:0:0:0: [sdc] Mode Sense: 02 00 00 00
[ 379.511323] sd 6:0:0:0: [sdc] No Caching mode page found
[ 379.511343] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 379.532714] sd 6:0:0:0: [sdc] No Caching mode page found
[ 379.532734] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 379.536788] sdc: sdc1
[ 379.554706] sd 6:0:0:0: [sdc] No Caching mode page found
[ 379.554767] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 379.554779] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 380.053074] usb 1-3: USB disconnect, device number 4
[ 380.060737] scsi 6:0:0:0: [sdc] Unhandled error code
[ 380.060756] scsi 6:0:0:0: [sdc]
[ 380.060763] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 380.060771] scsi 6:0:0:0: [sdc] CDB:
[ 380.060786] Read(10): 28 00 00 03 9e 70 00 00 08 00
[ 380.060816] end_request: I/O error, dev sdc, sector 237168
[ 380.060828] Buffer I/O error on device sdc, logical block 29646
[ 380.060950] Buffer I/O error on device sdc, logical block 29646
[ 380.061050] Buffer I/O error on device sdc, logical block 29694
[ 380.061063] Buffer I/O error on device sdc, logical block 29694
[ 380.061096] Buffer I/O error on device sdc, logical block 1
[ 380.061107] Buffer I/O error on device sdc, logical block 1
[ 380.061126] Buffer I/O error on device sdc, logical block 1
[ 380.061175] Buffer I/O error on device sdc, logical block 29695
[ 380.061198] Buffer I/O error on device sdc, logical block 0
[ 380.314184] usb 1-3: new high-speed USB device number 5 using ehci_hcd
[ 380.492929] usb 1-3: device descriptor read/all, error -71
[ 380.550182] hub 1-0:1.0: unable to enumerate USB device on port 3
[ 380.894134] usb 3-3: new full-speed USB device number 2 using ohci_hcd
[ 381.114943] usb 3-3: New USB device found, idVendor=0979, idProduct=0371
[ 381.114961] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 381.114971] usb 3-3: Product: USB 2.0 Device
[ 381.114979] usb 3-3: Manufacturer: Jeilin
[ 381.114988] usb 3-3: SerialNumber: JL2007BV2000
[ 381.124495] scsi7 : usb-storage 3-3:1.0
[ 382.164888] scsi 7:0:0:0: Direct-Access General USB FLASH Drive 1.00 PQ: 0 ANSI: 0 CCS
[ 382.168178] sd 7:0:0:0: Attached scsi generic sg4 type 0
[ 382.177705] sd 7:0:0:0: [sdc] 237568 512-byte logical blocks: (121 MB/116 MiB)
[ 382.186822] sd 7:0:0:0: [sdc] Write Protect is off
[ 382.186843] sd 7:0:0:0: [sdc] Mode Sense: 02 00 00 00
[ 382.195847] sd 7:0:0:0: [sdc] No Caching mode page found
[ 382.195867] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 382.238051] sd 7:0:0:0: [sdc] No Caching mode page found
[ 382.238072] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 382.250084] sdc: sdc1
[ 382.289839] sd 7:0:0:0: [sdc] No Caching mode page found
[ 382.289859] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 382.289871] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[ 757.936409] usb 3-3: USB disconnect, device number 2
[ 800.302052] audit_printk_skb: 124 callbacks suppressed
[ 800.302067] type=1400 audit(1419585637.283:27): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=596 comm="cupsd" pid=596 comm="cupsd" capability=36 capname="block_suspend"
[ 857.687466] PPP BSD Compression module registered
[ 857.729453] PPP Deflate Compression module registered
[ 892.597358] usb 1-3: new high-speed USB device number 7 using ehci_hcd
[ 892.677423] hub 1-0:1.0: unable to enumerate USB device on port 3
[ 988.920651] usb 1-3: new high-speed USB device number 8 using ehci_hcd
[ 989.108435] usb 1-3: New USB device found, idVendor=0979, idProduct=0371
[ 989.108452] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 989.108462] usb 1-3: Product: USB 2.0 Device
[ 989.108471] usb 1-3: Manufacturer: Jeilin
[ 989.108479] usb 1-3: SerialNumber: JL2007BV2000
[ 989.116350] scsi8 : usb-storage 1-3:1.0
[ 990.155837] scsi 8:0:0:0: Direct-Access General USB FLASH Drive 1.00 PQ: 0 ANSI: 0 CCS
[ 990.159287] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 990.163963] sd 8:0:0:0: [sdc] 237568 512-byte logical blocks: (121 MB/116 MiB)
[ 990.170168] sd 8:0:0:0: [sdc] Write Protect is off
[ 990.170190] sd 8:0:0:0: [sdc] Mode Sense: 02 00 00 00
[ 990.176061] sd 8:0:0:0: [sdc] No Caching mode page found
[ 990.176076] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 990.196307] sd 8:0:0:0: [sdc] No Caching mode page found
[ 990.196328] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 990.199590] sdc: sdc1
[ 990.219911] sd 8:0:0:0: [sdc] No Caching mode page found
[ 990.219954] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 990.219967] sd 8:0:0:0: [sdc] Attached SCSI removable disk
[ 1080.670865] usb 1-3: USB disconnect, device number 8
[ 3308.592829] PM: Syncing filesystems ... done.
[ 3308.604055] PM: Preparing system for mem sleep
[ 3308.604092] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 3308.621631] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 3308.637452] PM: Entering mem sleep
[ 3308.637583] Suspending console(s) (use no_console_suspend to debug)
[ 3308.638281] option1 ttyUSB0: option_instat_callback: error -2
[ 3308.638331] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 3308.678186] pciehp 0000:00:07.0:pcie04: pciehp_suspend ENTRY
[ 3308.678309] ACPI handle has no context!
[ 3308.678321] [fglrx:firegl_pplib_notify_event] *ERROR* PPLIB: PPLib Notify Event failed!
[ 3308.678327] [fglrx:firegl_pplib_notify_event] *ERROR* ulEventType = 00000002, ulEventData = 00000000
[ 3308.678426] [fglrx] IRQ 45 Disabled
[ 3308.678682] [fglrx] Preparing suspend fglrx in kernel.
[ 3308.733848] sd 0:0:0:0: [sda] Stopping disk
[ 3308.771964] [fglrx] Suspending fglrx in kernel completed.
[ 3308.771969] [fglrx] Power down the ASIC .
[ 3308.797207] PM: suspend of drv:snd_hda_intel dev:0000:00:14.2 complete after 119.765 msecs
[ 3309.308738] PM: suspend of drv:sd dev:0:0:0:0 complete after 670.564 msecs
[ 3309.308767] PM: suspend of drv:scsi dev:target0:0:0 complete after 670.464 msecs
[ 3309.308784] PM: suspend of drv:scsi dev:host0 complete after 670.409 msecs
[ 3309.308916] PM: suspend of drv: dev:ata1 complete after 670.273 msecs
[ 3309.308972] PM: suspend of drv:ahci dev:0000:00:11.0 complete after 630.973 msecs
[ 3309.308990] PM: suspend of drv: dev:pci0000:00 complete after 627.881 msecs
[ 3309.309004] PM: suspend of devices complete after 671.281 msecs
[ 3309.309018] PM: suspend devices took 0.672 seconds
[ 3309.309365] PM: late suspend of devices complete after 0.341 msecs
[ 3309.329113] pcieport 0000:00:15.0: wake-up capability enabled by ACPI
[ 3309.345543] ehci_hcd 0000:00:13.2: wake-up capability enabled by ACPI
[ 3309.361113] ohci_hcd 0000:00:13.0: wake-up capability enabled by ACPI
[ 3309.361157] ehci_hcd 0000:00:12.2: wake-up capability enabled by ACPI
[ 3309.377109] ohci_hcd 0000:00:12.0: wake-up capability enabled by ACPI
[ 3309.377265] PM: noirq suspend of devices complete after 67.908 msecs
[ 3309.377310] ACPI: Preparing to enter system sleep state S3
[ 3309.425107] PM: Saving platform NVS memory
[ 3309.431147] Disabling non-boot CPUs ...
[ 3309.431750] Broke affinity for irq 17
[ 3309.532986] CPU 1 is now offline
[ 3309.534098] ACPI: Low-level resume complete
[ 3309.534190] PM: Restoring platform NVS memory
[ 3309.535669] LVT offset 0 assigned for vector 0x400
[ 3309.535812] Enabling non-boot CPUs ...
[ 3309.536088] Booting Node 0 Processor 1 APIC 0x1
[ 3309.550243] CPU1 is up
[ 3309.551322] ACPI: Waking up from system sleep state S3
[ 3309.619475] ohci_hcd 0000:00:12.0: wake-up capability disabled by ACPI
[ 3309.634958] ehci_hcd 0000:00:12.2: wake-up capability disabled by ACPI
[ 3309.635017] ohci_hcd 0000:00:13.0: wake-up capability disabled by ACPI
[ 3309.650957] ehci_hcd 0000:00:13.2: wake-up capability disabled by ACPI
[ 3309.653736] PM: noirq resume of devices complete after 34.690 msecs
[ 3309.654059] PM: early resume of devices complete after 0.216 msecs
[ 3309.654479] snd_hda_intel 0000:00:01.1: irq 43 for MSI/MSI-X
[ 3309.654614] pciehp 0000:00:07.0:pcie04: pciehp_resume ENTRY
[ 3309.666369] pcieport 0000:00:15.0: wake-up capability disabled by ACPI
[ 3309.667503] [fglrx] Power up the ASIC
[ 3309.688512] [fglrx] Preparing resume fglrx in kernel.
[ 3309.709157] [fglrx] Resuming fglrx in kernel completed.
[ 3309.709247] [fglrx] IRQ 45 Enabled
[ 3309.786963] PM: resume of drv: dev:ep_00 complete after 131.459 msecs
[ 3309.787023] PM: resume of drv: dev:ep_00 complete after 131.393 msecs
[ 3309.787036] PM: resume of drv:hub dev:3-0:1.0 complete after 131.743 msecs
[ 3309.787040] PM: resume of drv:hub dev:4-0:1.0 complete after 131.465 msecs
[ 3309.787049] PM: resume of drv: dev:ep_81 complete after 131.759 msecs
[ 3309.787057] PM: resume of drv: dev:ep_81 complete after 131.459 msecs
[ 3309.839111] PM: resume of drv:usb dev:1-2 complete after 182.797 msecs
[ 3309.839185] PM: resume of drv:option dev:1-2:1.0 complete after 182.849 msecs
[ 3309.839203] PM: resume of drv:hub dev:1-0:1.0 complete after 183.956 msecs
[ 3309.839208] PM: resume of drv:option dev:1-2:1.2 complete after 182.686 msecs
[ 3309.839224] PM: resume of drv:usb-storage dev:1-2:1.4 complete after 182.515 msecs
[ 3309.839241] PM: resume of drv: dev:ep_00 complete after 183.995 msecs
[ 3309.839244] PM: resume of drv: dev:ep_00 complete after 182.216 msecs
[ 3309.839253] PM: resume of drv:usb dev:1-2:1.1 complete after 182.794 msecs
[ 3309.839256] PM: resume of drv: dev:ep_81 complete after 182.888 msecs
[ 3309.839263] PM: resume of drv: dev:ep_01 complete after 182.838 msecs
[ 3309.839267] PM: resume of drv:option dev:1-2:1.3 complete after 182.652 msecs
[ 3309.839271] PM: resume of drv: dev:ep_85 complete after 182.724 msecs
[ 3309.839277] PM: resume of drv: dev:ep_03 complete after 182.697 msecs
[ 3309.839284] PM: resume of drv:usb-storage dev:1-2:1.5 complete after 182.415 msecs
[ 3309.839287] PM: resume of drv:option1 dev:ttyUSB1 complete after 182.188 msecs
[ 3309.839294] PM: resume of drv:scsi dev:host4 complete after 182.554 msecs
[ 3309.839301] PM: resume of drv: dev:ep_82 complete after 182.905 msecs
[ 3309.839308] PM: resume of drv: dev:ep_87 complete after 182.469 msecs
[ 3309.839312] PM: resume of drv:option1 dev:ttyUSB0 complete after 182.250 msecs
[ 3309.839316] PM: resume of drv:scsi_host dev:host4 complete after 182.542 msecs
[ 3309.839320] PM: resume of drv: dev:ep_81 complete after 184.078 msecs
[ 3309.839323] PM: resume of drv:scsi dev:target4:0:0 complete after 182.164 msecs
[ 3309.839329] PM: resume of drv: dev:ep_05 complete after 182.520 msecs
[ 3309.839335] PM: resume of drv:sr dev:4:0:0:0 complete after 182.145 msecs
[ 3309.839338] PM: resume of drv: dev:ep_83 complete after 182.849 msecs
[ 3309.839345] PM: resume of drv: dev:ep_86 complete after 182.699 msecs
[ 3309.839351] PM: resume of drv: dev:ep_04 complete after 182.675 msecs
[ 3309.839355] PM: resume of drv:scsi_device dev:4:0:0:0 complete after 182.132 msecs
[ 3309.839359] PM: resume of drv:option1 dev:ttyUSB2 complete after 182.230 msecs
[ 3309.839367] PM: resume of drv:scsi dev:host5 complete after 182.467 msecs
[ 3309.839405] PM: resume of drv: dev:ep_88 complete after 182.411 msecs
[ 3309.839411] PM: resume of drv:scsi_host dev:host5 complete after 182.478 msecs
[ 3309.839414] PM: resume of drv: dev:ep_06 complete after 182.449 msecs
[ 3309.839419] PM: resume of drv:scsi dev:target5:0:0 complete after 182.166 msecs
[ 3309.839435] PM: resume of drv:sd dev:5:0:0:0 complete after 182.147 msecs
[ 3309.839458] PM: resume of drv:scsi_device dev:5:0:0:0 complete after 182.139 msecs
[ 3309.907091] usb 2-1: reset high-speed USB device number 2 using ehci_hcd
[ 3310.113138] PM: resume of drv: dev:ep_00 complete after 457.101 msecs
[ 3310.113203] PM: resume of drv:uvcvideo dev:2-1:1.1 complete after 457.211 msecs
[ 3310.113226] PM: resume of drv:uvcvideo dev:2-1:1.0 complete after 457.283 msecs
[ 3310.113259] PM: resume of drv: dev:ep_83 complete after 457.301 msecs
[ 3310.147006] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3310.156771] ata2.00: configured for UDMA/100
[ 3310.191234] PM: resume of drv:scsi dev:host1 complete after 535.406 msecs
[ 3310.191318] PM: resume of drv:scsi dev:target1:0:0 complete after 535.184 msecs
[ 3310.191338] PM: resume of drv:sr dev:1:0:0:0 complete after 535.176 msecs
[ 3310.191358] PM: resume of drv:scsi_host dev:host1 complete after 535.500 msecs
[ 3310.191365] PM: resume of drv:scsi_device dev:1:0:0:0 complete after 535.171 msecs
[ 3311.994626] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3311.998226] ata1.00: configured for UDMA/100
[ 3312.014715] PM: resume of drv:scsi dev:host0 complete after 2359.344 msecs
[ 3312.014737] PM: resume of drv:ata_port dev:ata1 complete after 2287.688 msecs
[ 3312.014742] PM: resume of drv:scsi_host dev:host0 complete after 2359.348 msecs
[ 3312.014749] PM: resume of drv:scsi dev:target0:0:0 complete after 2359.107 msecs
[ 3312.014759] PM: resume of drv:sd dev:0:0:0:0 complete after 2359.083 msecs
[ 3312.014768] sd 0:0:0:0: [sda] Starting disk
[ 3312.031955] PM: resume of drv:scsi_device dev:0:0:0:0 complete after 2376.240 msecs
[ 3312.447111] PM: resume of devices complete after 2793.645 msecs
[ 3312.447332] PM: resume devices took 2.796 seconds
[ 3312.447508] PM: Finishing wakeup.
[ 3312.448662] usb 1-2: USB disconnect, device number 3
[ 3312.458424] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 3312.458472] option 1-2:1.0: device disconnected
[ 3312.458932] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 3312.458971] option 1-2:1.2: device disconnected
[ 3312.459158] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 3312.459189] option 1-2:1.3: device disconnected
[ 3312.447512] Restarting tasks ... done.
[ 3312.492961] video LNXVIDEO:00: Restoring backlight state
[ 3313.854097] usb 1-2: new high-speed USB device number 9 using ehci_hcd
[ 3313.986978] usb 1-2: New USB device found, idVendor=12d1, idProduct=14fe
[ 3313.986990] usb 1-2: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[ 3313.986996] usb 1-2: Product: HUAWEI Mobile
[ 3313.987000] usb 1-2: Manufacturer: HUAWEI
[ 3313.995284] scsi9 : usb-storage 1-2:1.0
[ 3314.006197] scsi10 : usb-storage 1-2:1.1
[ 3314.997451] scsi 9:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 3315.007759] sr1: scsi-1 drive
[ 3315.009418] sr 9:0:0:0: Attached scsi CD-ROM sr1
[ 3315.011071] sr 9:0:0:0: Attached scsi generic sg2 type 5
[ 3315.018047] scsi 10:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 3315.019762] sd 10:0:0:0: Attached scsi generic sg3 type 0
[ 3315.023033] sd 10:0:0:0: [sdb] Attached SCSI removable disk
[ 3315.255589] usb 1-2: USB disconnect, device number 9
[ 3315.265705] scsi 10:0:0:0: rejecting I/O to offline device
[ 3315.265722] scsi 10:0:0:0: killing request
[ 3315.790558] r8169 0000:03:00.0: eth0: link down
[ 3315.791145] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3315.798398] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 3319.952795] usb 1-2: new high-speed USB device number 10 using ehci_hcd
[ 3320.086220] usb 1-2: New USB device found, idVendor=12d1, idProduct=1506
[ 3320.086231] usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[ 3320.086237] usb 1-2: Product: HUAWEI Mobile
[ 3320.086242] usb 1-2: Manufacturer: HUAWEI
[ 3320.089156] option 1-2:1.0: GSM modem (1-port) converter detected
[ 3320.089935] usb 1-2: GSM modem (1-port) converter now attached to ttyUSB0
[ 3320.090232] option 1-2:1.2: GSM modem (1-port) converter detected
[ 3320.090767] usb 1-2: GSM modem (1-port) converter now attached to ttyUSB1
[ 3320.090926] option 1-2:1.3: GSM modem (1-port) converter detected
[ 3320.091391] usb 1-2: GSM modem (1-port) converter now attached to ttyUSB2
[ 3320.096783] scsi11 : usb-storage 1-2:1.4
[ 3320.100951] scsi12 : usb-storage 1-2:1.5
[ 3321.101298] scsi 11:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 3321.102517] scsi 12:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 3321.106642] sr1: scsi-1 drive
[ 3321.107202] sr 11:0:0:0: Attached scsi CD-ROM sr1
[ 3321.107555] sr 11:0:0:0: Attached scsi generic sg2 type 5
[ 3321.110311] sd 12:0:0:0: Attached scsi generic sg3 type 0
[ 3321.111777] sd 12:0:0:0: [sdb] Attached SCSI removable disk
[ 3368.340866] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 3368.341616] ISOFS: changing to secondary root
Dík a dobrou chut.
-
ppp0 Link encap:Point-to-Point Protokol
inet adr:10.84.244.34 P-t-P:10.64.64.64 Maska:255.255.255.255
AKTIVOVÁNO POINTOPOINT BĚŽÍ NEARP MULTICAST MTU:1500 Metrika:1
RX packets:48796 errors:0 dropped:0 overruns:0 frame:0
TX packets:40758 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:3
Přijato bajtů: 41198908 (41.1 MB) Odesláno bajtů: 6270491 (6.2 MB)
Nastavuji balík qmail (1.06-4) …
The hostname -f command returned: $1
Your system needs to have a fully qualified domain name (fqdn) in
order to install the var-qmail packages.
Installation aborted.
Při zpracování nastaly chyby:
qmail
qmail-run
E: Sub-process /usr/bin/dpkg returned an error code (1)
si asi pripojený cez modem, a okrem toho máš problém s balíčkom gmail
viacej tu (http://askubuntu.com/questions/435786/owncloud-problem-installing-packages) , v prvom rade pošli tento výpis (http://forum.ubuntu.cz/index.php?topic=73184.msg527533#msg527533) aby bolo jasné čo máš za železo ...
-
1) pise ti to (sice nechapu co to dela s qmail), ze ti chybi fqdn .. uprav etc/hosts .. viz hosts manual
2) ukaz vystup z:
ip link set wkan0 up
iwlist wlan0 scan
-
Pěkný večer
davoss@davoss-HP-255-G1-Notebook-PC:~$ ip link set wkan0 up
Cannot find device "wkan0"
davoss@davoss-HP-255-G1-Notebook-PC:~$ iwlist wlan0 scan
wlan0 Failed to read scan data : Network is down
Tak tohle......................
-
davoss@davoss-HP-255-G1-Notebook-PC:~$ wget -N -t 5 -T 10 http://dl.dropbox.com/u/57264241/wireless_script && \
> chmod +x wireless_script && \
> ./wireless_script
--2014-12-26 20:51:34-- http://dl.dropbox.com/u/57264241/wireless_script
Překládám dl.dropbox.com (dl.dropbox.com)… 54.243.116.95
Navazuje se spojení s dl.dropbox.com (dl.dropbox.com)|54.243.116.95|:80… spojeno.
HTTP požadavek odeslán, program čeká na odpověď… 302 FOUND
Přesměrováno na: http://dl.dropboxusercontent.com/u/57264241/wireless_script [následuji]
--2014-12-26 20:51:34-- http://dl.dropboxusercontent.com/u/57264241/wireless_script
Překládám dl.dropboxusercontent.com (dl.dropboxusercontent.com)… 184.72.240.186, 184.73.161.30, 174.129.38.110, ...
Navazuje se spojení s dl.dropboxusercontent.com (dl.dropboxusercontent.com)|184.72.240.186|:80… spojeno.
HTTP požadavek odeslán, program čeká na odpověď… 302 FOUND
Cookie přišedši z dl.dropboxusercontent.com se pokusila nastavit doménu na dl.dropboxusercontent.com
Cookie přišedši z dl.dropboxusercontent.com se pokusila nastavit doménu na dl.dropboxusercontent.com
Přesměrováno na: https://dl.dropboxusercontent.com/u/57264241/wireless_script [následuji]
--2014-12-26 20:51:34-- https://dl.dropboxusercontent.com/u/57264241/wireless_script
Navazuje se spojení s dl.dropboxusercontent.com (dl.dropboxusercontent.com)|184.72.240.186|:443… spojeno.
HTTP požadavek odeslán, program čeká na odpověď… 200 OK
Délka: 13362 (13K) [text/plain]
Nelze použít časová razítka, protože v odpovědi serveru
schází hlavička „Last-modified“.
--2014-12-26 20:51:35-- https://dl.dropboxusercontent.com/u/57264241/wireless_script
Využije se existující spojení s dl.dropboxusercontent.com:443.
HTTP požadavek odeslán, program čeká na odpověď… 200 OK
Délka: 13362 (13K) [text/plain]
Ukládám do: „wireless_script“
100%[======================================>] 13 362 --.-K/s za 0s
2014-12-26 20:51:36 (85,1 MB/s) – „wireless_script“ uloženo [13362/13362]
Results saved in "/home/davoss/wireless-info.txt".
-
Results saved in "/home/davoss/wireless-info.txt".
po slovensky: výsledok je uložený v "/home/davoss/wireless-info.txt"
tak ho teda sem pošli , a prosím, ulož ho do tagu # ( vložiť kód ) inak sa to nedá vôbec čítať
-
#
Ubuntu
##### lspci #############################
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 07)
Subsystem: Hewlett-Packard Company Device [103c:188b]
Kernel driver in use: r8169
07:00.0 Network controller [0280]: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe [1814:3290]
Subsystem: Hewlett-Packard Company Ralink RT3290LE 802.11bgn 1x1 Wi-Fi and Bluetooth 4.0 Combo Adapter [103c:18ec]
Kernel driver in use: rt2800pci
##### lsusb #############################
Bus 001 Device 003: ID 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
Bus 002 Device 002: ID 064e:e263 Suyin Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
##### PCMCIA card info ##################
##### rfkill ############################
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
##### lsmod #############################
hp_wmi 18093 0
sparse_keymap 13891 1 hp_wmi
rt2800pci 18522 0
rt2800lib 62728 1 rt2800pci
crc_ccitt 12708 2 ppp_async,rt2800lib
rt2x00pci 14477 1 rt2800pci
rt2x00lib 54856 3 rt2800pci,rt2800lib,rt2x00pci
mac80211 557966 3 rt2800lib,rt2x00pci,rt2x00lib
cfg80211 211292 2 rt2x00lib,mac80211
compat 14957 3 rt2800pci,mac80211,cfg80211
eeprom_93cx6 13345 1 rt2800pci
wmi 19257 1 hp_wmi
##### interfaces ########################
auto lo
iface lo inet loopback
##### ifconfig ##########################
eth0 Link encap:Ethernet HWaddr a0:48:1c:ed:5c:4e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.177.104.203 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:36904 errors:0 dropped:0 overruns:0 frame:0
TX packets:29191 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:31044890 (31.0 MB) TX bytes:4683799 (4.6 MB)
wlan0 Link encap:Ethernet HWaddr 70:18:8b:d9:1e:85
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
##### iwconfig ##########################
ppp0 no wireless extensions.
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
##### route #############################
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0
10.64.64.64 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 ppp0
##### resolv.conf #######################
nameserver 127.0.0.1
##### nm-tool ###########################
NetworkManager Tool
State: connected (global)
- Device: ttyUSB0 [T-Mobile Výchozí] ----------------------------------------
Type: Mobile Broadband (GSM)
Driver: option1
State: connected
Default: yes
Capabilities:
IPv4 Settings:
Address: 10.177.104.203
Prefix: 32 (255.255.255.255)
Gateway: 10.64.64.64
DNS: 93.153.117.1
DNS: 93.153.117.33
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: rt2800pci
State: unavailable
Default: no
HW Address: 70:18:8B:D9:1E:85
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: A0:48:1C:ED:5C:4E
Capabilities:
Carrier Detect: yes
Wired Properties
Carrier: off
##### NetworkManager.state ##############
[main]
NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
WimaxEnabled=true
##### NetworkManager.conf ###############
[main]
plugins=ifupdown,keyfile
dns=dnsmasq
[ifupdown]
managed=false
##### NetworkManager profiles ###########
Snad jsem tě pochopil a půjde to přečíst.Jestli ne,tak omluva.Fakt nejsem tak kovanej v počítačích jako vy ostatní tady.
-
Takhle pane kolego :
[příloha smazaná administrátorem]
-
ale to nebude celý výpis ... tam chýba veľa veci . skus to ešte raz
-
Dávám to natvrdo.A jestli to už nepůjde,kašlu na to.Někam to zanesu a bude....................
########## wireless info START ##########
Report from: 26 Dec 2014 21:17 CET +0100
Booted last: 26 Dec 2014 20:13 CET +0100
Script from: 20 Sep 2014 23:04 UTC +0000
##### release ###########################
Distributor ID: Ubuntu
Description: Ubuntu 12.04.5 LTS
Release: 12.04
Codename: precise
##### kernel ############################
Linux 3.5.0-57-generic #84~precise1-Ubuntu SMP Thu Nov 6 06:09:35 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
Parameters: ro, quiet, splash, vt.handoff=7
##### desktop ###########################
Ubuntu
##### lspci #############################
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 07)
Subsystem: Hewlett-Packard Company Device [103c:188b]
Kernel driver in use: r8169
07:00.0 Network controller [0280]: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe [1814:3290]
Subsystem: Hewlett-Packard Company Ralink RT3290LE 802.11bgn 1x1 Wi-Fi and Bluetooth 4.0 Combo Adapter [103c:18ec]
Kernel driver in use: rt2800pci
##### lsusb #############################
Bus 001 Device 003: ID 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
Bus 002 Device 002: ID 064e:e263 Suyin Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
##### PCMCIA card info ##################
##### rfkill ############################
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
##### lsmod #############################
hp_wmi 18093 0
sparse_keymap 13891 1 hp_wmi
rt2800pci 18522 0
rt2800lib 62728 1 rt2800pci
crc_ccitt 12708 2 ppp_async,rt2800lib
rt2x00pci 14477 1 rt2800pci
rt2x00lib 54856 3 rt2800pci,rt2800lib,rt2x00pci
mac80211 557966 3 rt2800lib,rt2x00pci,rt2x00lib
cfg80211 211292 2 rt2x00lib,mac80211
compat 14957 3 rt2800pci,mac80211,cfg80211
eeprom_93cx6 13345 1 rt2800pci
wmi 19257 1 hp_wmi
##### interfaces ########################
auto lo
iface lo inet loopback
##### ifconfig ##########################
eth0 Link encap:Ethernet HWaddr a0:48:1c:ed:5c:4e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.177.104.203 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:36904 errors:0 dropped:0 overruns:0 frame:0
TX packets:29191 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:31044890 (31.0 MB) TX bytes:4683799 (4.6 MB)
wlan0 Link encap:Ethernet HWaddr 70:18:8b:d9:1e:85
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
##### iwconfig ##########################
ppp0 no wireless extensions.
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
##### route #############################
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0
10.64.64.64 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 ppp0
##### resolv.conf #######################
nameserver 127.0.0.1
##### nm-tool ###########################
NetworkManager Tool
State: connected (global)
- Device: ttyUSB0 [T-Mobile Výchozí] ----------------------------------------
Type: Mobile Broadband (GSM)
Driver: option1
State: connected
Default: yes
Capabilities:
IPv4 Settings:
Address: 10.177.104.203
Prefix: 32 (255.255.255.255)
Gateway: 10.64.64.64
DNS: 93.153.117.1
DNS: 93.153.117.33
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: rt2800pci
State: unavailable
Default: no
HW Address: 70:18:8B:D9:1E:85
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: A0:48:1C:ED:5C:4E
Capabilities:
Carrier Detect: yes
Wired Properties
Carrier: off
##### NetworkManager.state ##############
[main]
NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
WimaxEnabled=true
##### NetworkManager.conf ###############
[main]
plugins=ifupdown,keyfile
dns=dnsmasq
[ifupdown]
managed=false
##### NetworkManager profiles ###########
-
ok , hlavne klid :)
-
########## wireless info START ##########
Report from: 26 Dec 2014 22:07 CET +0100
Booted last: 26 Dec 2014 20:13 CET +0100
Script from: 20 Sep 2014 23:04 UTC +0000
##### release ###########################
Distributor ID: Ubuntu
Description: Ubuntu 12.04.5 LTS
Release: 12.04
Codename: precise
##### kernel ############################
Linux 3.5.0-57-generic #84~precise1-Ubuntu SMP Thu Nov 6 06:09:35 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
Parameters: ro, quiet, splash, vt.handoff=7
##### desktop ###########################
Ubuntu
##### lspci #############################
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 07)
Subsystem: Hewlett-Packard Company Device [103c:188b]
Kernel driver in use: r8169
07:00.0 Network controller [0280]: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe [1814:3290]
Subsystem: Hewlett-Packard Company Ralink RT3290LE 802.11bgn 1x1 Wi-Fi and Bluetooth 4.0 Combo Adapter [103c:18ec]
Kernel driver in use: rt2800pci
##### lsusb #############################
Bus 001 Device 003: ID 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
Bus 002 Device 002: ID 064e:e263 Suyin Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
##### PCMCIA card info ##################
##### rfkill ############################
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
##### lsmod #############################
hp_wmi 18093 0
sparse_keymap 13891 1 hp_wmi
rt2800pci 18522 0
rt2800lib 62728 1 rt2800pci
crc_ccitt 12708 2 ppp_async,rt2800lib
rt2x00pci 14477 1 rt2800pci
rt2x00lib 54856 3 rt2800pci,rt2800lib,rt2x00pci
mac80211 557966 3 rt2800lib,rt2x00pci,rt2x00lib
cfg80211 211292 2 rt2x00lib,mac80211
compat 14957 3 rt2800pci,mac80211,cfg80211
eeprom_93cx6 13345 1 rt2800pci
wmi 19257 1 hp_wmi
##### interfaces ########################
auto lo
iface lo inet loopback
##### ifconfig ##########################
eth0 Link encap:Ethernet HWaddr <MAC 'eth0' [IF]>
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.177.104.203 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:45492 errors:0 dropped:0 overruns:0 frame:0
TX packets:37129 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:35908315 (35.9 MB) TX bytes:6204198 (6.2 MB)
wlan0 Link encap:Ethernet HWaddr <MAC 'wlan0' [IF]>
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
##### iwconfig ##########################
ppp0 no wireless extensions.
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
##### route #############################
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0
10.64.64.64 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 ppp0
##### resolv.conf #######################
nameserver 127.0.0.1
##### nm-tool ###########################
NetworkManager Tool
State: connected (global)
- Device: ttyUSB0 [T-Mobile Výchozí] ----------------------------------------
Type: Mobile Broadband (GSM)
Driver: option1
State: connected
Default: yes
Capabilities:
IPv4 Settings:
Address: 10.177.104.203
Prefix: 32 (255.255.255.255)
Gateway: 10.64.64.64
DNS: 93.153.117.1
DNS: 93.153.117.33
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: rt2800pci
State: unavailable
Default: no
HW Address: <MAC 'wlan0' [IF]>
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: <MAC 'eth0' [IF]>
Capabilities:
Carrier Detect: yes
Wired Properties
Carrier: off
##### NetworkManager.state ##############
[main]
NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
WimaxEnabled=true
##### NetworkManager.conf ###############
[main]
plugins=ifupdown,keyfile
dns=dnsmasq
[ifupdown]
managed=false
##### NetworkManager profiles ###########
[[/etc/NetworkManager/system-connections/Hotspot]] (600 root)
[connection] id=Hotspot | type=802-11-wireless | autoconnect=false
[802-11-wireless] ssid=davoss-HP-255-G1-Notebook-PC | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=shared
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/Vydra]] (600 root)
[connection] id=Vydra | type=802-11-wireless
[802-11-wireless] ssid=Vydra | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/WIFI COR]] (600 root)
[connection] id=WIFI COR | type=802-11-wireless
[802-11-wireless] ssid=WIFI COR | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/LeoExpress]] (600 root)
[connection] id=LeoExpress | type=802-11-wireless
[802-11-wireless] ssid=LeoExpress | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/davoss]] (600 root)
[connection] id=davoss | type=802-11-wireless
[802-11-wireless] ssid=davoss | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/Dekada]] (600 root)
[connection] id=Dekada | type=802-11-wireless
[802-11-wireless] ssid=Dekada | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/Svatava - iPad]] (600 root)
[connection] id=Svatava - iPad | type=802-11-wireless
[802-11-wireless] ssid=Svatava - iPad | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/Regiojet]] (600 root)
[connection] id=Regiojet | type=802-11-wireless
[802-11-wireless] ssid=Regiojet | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/MITHEA]] (600 root)
[connection] id=MITHEA | type=802-11-wireless
[802-11-wireless] ssid=MITHEA | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/Bezdrátové připojení 1]] (600 root)
[connection] id=Bezdrátové připojení 1 | type=802-11-wireless
[802-11-wireless] ssid=Ostrava | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/CeskyTesin]] (600 root)
[connection] id=CeskyTesin | type=802-11-wireless
[802-11-wireless] ssid=CeskyTesin | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/WLAN-11g-AP]] (600 root)
[connection] id=WLAN-11g-AP | type=802-11-wireless
[802-11-wireless] ssid=WLAN-11g-AP | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/At zije Divadlo Sklep! :)]] (600 root)
[connection] id=At zije Divadlo Sklep! :) | type=802-11-wireless
[802-11-wireless] ssid=At zije Divadlo Sklep! :) | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/ZLUTY]] (600 root)
[connection] id=ZLUTY | type=802-11-wireless
[802-11-wireless] ssid=ZLUTY | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/AP-P]] (600 root)
[connection] id=AP-P | type=802-11-wireless
[802-11-wireless] ssid=AP-P | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/Internet]] (600 root)
[connection] id=Internet | type=802-11-wireless
[802-11-wireless] ssid=Internet | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/Android Hotspot7370]] (600 root)
[connection] id=Android Hotspot7370 | type=802-11-wireless
[802-11-wireless] ssid=Android Hotspot7370 | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/sporthotel2]] (600 root)
[connection] id=sporthotel2 | type=802-11-wireless
[802-11-wireless] ssid=sporthotel2 | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
[[/etc/NetworkManager/system-connections/csobAP]] (600 root)
[connection] id=csobAP | type=802-11-wireless
[802-11-wireless] ssid=csobAP | mac-address=<MAC 'wlan0' [IF]>
[ipv6] method=auto
[ipv4] method=auto
[[/etc/NetworkManager/system-connections/Dekada 1]] (600 root)
[connection] id=Dekada 1 | type=802-11-wireless
[802-11-wireless] ssid=Dekada | mac-address=<MAC 'wlan0' [IF]>
[ipv4] method=auto
[ipv6] method=auto
##### iw reg get ########################
Region: Europe/Prague (based on set time zone)
country 00:
(2402 - 2472 @ 40), (3, 20)
(2457 - 2482 @ 20), (3, 20), PASSIVE-SCAN, NO-IBSS
(2474 - 2494 @ 20), (3, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS
(5170 - 5250 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS
(5735 - 5835 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS
##### iwlist channels ###################
ppp0 no frequency information.
eth0 no frequency information.
lo no frequency information.
wlan0 14 channels in total; available frequencies :
Channel 01 : 2.412 GHz
Channel 02 : 2.417 GHz
Channel 03 : 2.422 GHz
Channel 04 : 2.427 GHz
Channel 05 : 2.432 GHz
Channel 06 : 2.437 GHz
Channel 07 : 2.442 GHz
Channel 08 : 2.447 GHz
Channel 09 : 2.452 GHz
Channel 10 : 2.457 GHz
Channel 11 : 2.462 GHz
Channel 12 : 2.467 GHz
Channel 13 : 2.472 GHz
Channel 14 : 2.484 GHz
##### iwlist scan #######################
ppp0 Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
lo Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
##### module infos ######################
[rt2800pci]
filename: /lib/modules/3.5.0-57-generic/updates/dkms/rt2800pci.ko
license: GPL
firmware: rt2860.bin
description: Ralink RT2800 PCI & PCMCIA Wireless LAN driver.
version: 3.0.0
author: http://rt2x00.serialmonkey.com
srcversion: 41B14A95C58ED67B6FB5F4C
depends: rt2x00lib,rt2800lib,rt2x00pci,compat,eeprom_93cx6
vermagic: 3.5.0-57-generic SMP mod_unload modversions
parm: nohwcrypt:Disable hardware encryption. (bool)
[rt2800lib]
filename: /lib/modules/3.5.0-57-generic/updates/dkms/rt2800lib.ko
license: GPL
description: Ralink RT2800 library
version: 3.0.0
author: http://rt2x00.serialmonkey.com, Bartlomiej Zolnierkiewicz
srcversion: 93046BBEA3A727AD14A7985
depends: rt2x00lib,mac80211,crc-ccitt
vermagic: 3.5.0-57-generic SMP mod_unload modversions
[rt2x00pci]
filename: /lib/modules/3.5.0-57-generic/updates/dkms/rt2x00pci.ko
license: GPL
description: rt2x00 pci library
version: 3.0.0
author: http://rt2x00.serialmonkey.com
srcversion: 93FC24DCA03D0CF9FAB79E7
depends: rt2x00lib,mac80211
vermagic: 3.5.0-57-generic SMP mod_unload modversions
[rt2x00lib]
filename: /lib/modules/3.5.0-57-generic/updates/dkms/rt2x00lib.ko
license: GPL
description: rt2x00 library
version: 3.0.0
author: http://rt2x00.serialmonkey.com
srcversion: FB31228361305FD1C6A3C11
depends: mac80211,cfg80211
vermagic: 3.5.0-57-generic SMP mod_unload modversions
[mac80211]
filename: /lib/modules/3.5.0-57-generic/updates/dkms/mac80211.ko
license: GPL
description: IEEE 802.11 subsystem
srcversion: 20383BD89331C672F84C85C
depends: cfg80211,compat
vermagic: 3.5.0-57-generic SMP mod_unload modversions
parm: max_nullfunc_tries:Maximum nullfunc tx tries before disconnecting (reason 4). (int)
parm: max_probe_tries:Maximum probe tries before disconnecting (reason 4). (int)
parm: probe_wait_ms:Maximum time(ms) to wait for probe response before disconnecting (reason 4). (int)
parm: ieee80211_default_rc_algo:Default rate control algorithm for mac80211 to use (charp)
[cfg80211]
filename: /lib/modules/3.5.0-57-generic/updates/dkms/cfg80211.ko
description: wireless configuration support
license: GPL
author: Johannes Berg
srcversion: 03EDA848F991DF674681216
depends: compat
vermagic: 3.5.0-57-generic SMP mod_unload modversions
parm: ieee80211_regdom:IEEE 802.11 regulatory domain code (charp)
parm: cfg80211_disable_40mhz_24ghz:Disable 40MHz support in the 2.4GHz band (bool)
##### module parameters #################
[rt2800pci]
nohwcrypt: N
[mac80211]
ieee80211_default_rc_algo: minstrel_ht
max_nullfunc_tries: 2
max_probe_tries: 5
probe_wait_ms: 500
[cfg80211]
cfg80211_disable_40mhz_24ghz: N
ieee80211_regdom: 00
##### /etc/modules ######################
lp
rtc
kbccmnd
lp
rtc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
disable_mmc
ath_pci
##### modprobe options ##################
[/etc/modprobe.d/blacklist-ath_pci.conf]
blacklist ath_pci
[/etc/modprobe.d/blacklist-bcm43.conf]
blacklist b43
blacklist b43legacy
blacklist ssb
blacklist bcm43xx
blacklist brcm80211
blacklist brcmfmac
blacklist brcmsmac
blacklist bcma
[/etc/modprobe.d/blacklist.conf]
blacklist evbug
blacklist usbmouse
blacklist usbkbd
blacklist eepro100
blacklist de4x5
blacklist eth1394
blacklist snd_intel8x0m
blacklist snd_aw2
blacklist i2c_i801
blacklist prism54
blacklist bcm43xx
blacklist garmin_gps
blacklist asus_acpi
blacklist snd_pcsp
blacklist pcspkr
blacklist amd76x_edac
[/etc/modprobe.d/blacklist-opensource-graphics.conf]
blacklist nouveau
blacklist radeon
blacklist lbm-nouveau
blacklist lbm-radeon
alias radeon off
alias lbm-radeon off
[/etc/modprobe.d/blacklist-rare-network.conf]
alias net-pf-3 off
alias net-pf-6 off
alias net-pf-9 off
alias net-pf-11 off
alias net-pf-12 off
alias net-pf-19 off
alias net-pf-21 off
alias net-pf-36 off
[/etc/modprobe.d/disable-mmc.conf]
install rtsx_pci /sbin/modprobe disable_mmc; /sbin/modprobe --ignore-install rtsx_pci
##### rc.local ##########################
service bluetooth restart
echo 0 > /sys/module/video/parameters/brightness_switch_enabled
exit 0
##### pm-utils ##########################
##### udev rules ########################
[/etc/udev/rules.d/70-persistent-net.rules]
# PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:15.0/0000:03:00.0 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="<MAC 'eth0' [IF]>", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
# PCI device 0x1814:/sys/devices/pci0000:00/0000:00:15.1/0000:07:00.0 (rt2800pci)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="<MAC 'wlan0' [IF]>", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
##### dmesg #############################
[ 21.018189] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 21.018525] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
########## wireless info END ############
Tak asi ted.Dík za trpělivost.Takhle ve svátek............
-
Pěkný večer
davoss@davoss-HP-255-G1-Notebook-PC:~$ ip link set wkan0 up
Cannot find device "wkan0"
davoss@davoss-HP-255-G1-Notebook-PC:~$ iwlist wlan0 scan
wlan0 Failed to read scan data : Network is down
Tak tohle......................
mel jsem tam preklep (za to omlouvam), nicmene ze tve reakce je naprosto zjevne, ze mozek nepouzivas a co ti to napise vubec nectes, takze je marne se snazit ti nejak pomahat ..
a prosim, pouzivej tag "code" aka "#", neda se na to divat a uz prede mnou ti to nekdo rikal