Fórum Ubuntu CZ/SK
Ubuntu pro osobní počítače => Instalace, aktualizace a spouštění => Téma založeno: karlitos 04 Října 2010, 17:34:28
-
Zdravim
Mel sem uzasny napad vymontovat disk z pocitace a kopirovat na nej pomoci USB prevodniku, po opetovne montazi > Read Error a odmita bootovat. Tak sem nabeh do Live CD a zkusil obnovit Grub 2 podle navodu na Wiki>
ubuntu@ubuntu:~$ sudo fdisk -l
Disk /dev/sda: 250.1 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xc09253ab
Device Boot Start End Blocks Id System
/dev/sda1 * 1 2611 20972826 83 Linux
/dev/sda2 2612 5222 20972857+ 7 HPFS/NTFS
/dev/sda3 29880 30401 4192965 82 Linux swap / Solaris
/dev/sda4 5223 29879 198057352+ 7 HPFS/NTFS
Partition table entries are not in disk order
ubuntu@ubuntu:~$ sudo fdisk -l
Disk /dev/sda: 250.1 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xc09253ab
Device Boot Start End Blocks Id System
/dev/sda1 * 1 2611 20972826 83 Linux
/dev/sda2 2612 5222 20972857+ 7 HPFS/NTFS
/dev/sda3 29880 30401 4192965 82 Linux swap / Solaris
/dev/sda4 5223 29879 198057352+ 7 HPFS/NTFS
Partition table entries are not in disk order
ubuntu@ubuntu:~$ sudo mount /dev/sda1 /mnt
ubuntu@ubuntu:~$ sudo mkdir /mnt/dev
mkdir: cannot create directory `/mnt/dev': File exists
ubuntu@ubuntu:~$ sudo mount --bind /dev /mnt/dev
ubuntu@ubuntu:~$ sudo chroot /mnt
ubuntu / # update-grub
Generating grub.cfg ...
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Found Debian background: linuxmint.png
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Found linux image: /boot/vmlinuz-2.6.32-24-generic-phc
Found initrd image: /boot/initrd.img-2.6.32-24-generic-phc
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Found linux image: /boot/vmlinuz-2.6.32-24-generic
Found initrd image: /boot/initrd.img-2.6.32-24-generic
Found memtest86+ image: /boot/memtest86+.bin
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
grep: /proc/mounts: No such file or directory
Cannot find list of partitions!
done
ubuntu / # grub-install /dev/sda
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Installation finished. No error reported.
ubuntu / # grub-install --recheck /dev/sda
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Is device-mapper driver missing from kernel?
/proc/devices: fopen failed: No such file or directory
Failed to set up list of device-mapper major numbers
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
/proc/devices: fopen failed: No such file or directory
Installation finished. No error reported.
Reset .... a zase Read Error, to same kdyz dam v menu LiveCD nabootovat z prvniho harddisku. Disk je v pocitaci jen jeden, jsou na nem 4 oddily, prvni je s Linuxem Mint 9 (buntu 10.04)
Moc prosim o radu, uz jsem zkousel asi treti navod a zkousel googlit chybove hlasky ale opet se ukazuje jak o tom vsem zase vim ho.... :-[
Diky K
-
Zkoušel jsi "nechrootový návod"?
http://forum.ubuntu.cz/index.php?topic=42267.0
Je disk v pořádku a správně připojený?
wiki - problémy při bootování (http://wiki.ubuntu.cz/%C5%98e%C5%A1en%C3%AD%20probl%C3%A9m%C5%AF/Bootov%C3%A1n%C3%AD)
Příp. připoj boot_info_script (http://wiki.ubuntu.cz/boot_info_script).
-
Zkoušel jsi přes recovery mode prostě jen obnovit zavaděč,klasicky příkazem update-grub
-
Diky vsem
Zkousel jsem i ten navod bez chroot - je uvedeny na nemecke ubuntu-Wiki - ale nepomohlo to.
Dival jsem se na ty rady pri chybach bootovani :
ubuntu@ubuntu:~$ sudo fsck -fv /dev/sda1
fsck z util-linux-ng 2.17.2
e2fsck 1.41.11 (14-Mar-2010)
Průchod 1: Kontroluji iuzly, bloky a velikosti
Průchod 2: Kontroluji strukturu adresářů
Průchod 3: Kontroluji dosažitelnost adresářů
Průchod 4: Kontroluji počty odkazů
Průchod 5: Kontroluji souhrnné informace skupin
349497 inodes used (26.61%)
435 non-contiguous files (0.1%)
582 non-contiguous directories (0.2%)
Počet iuzlů s ind/dind/tind bloky: 0/0/0
Histogram hloubky rozsahu: 257149/129/1
3506799 blocks used (66.89%)
0 bad blocks
1 large file
228183 regular files
24619 directories
61 character device files
26 block device files
2 fifos
536 links
96566 symbolic links (92088 fast symbolic links)
31 sockets
--------
350024 files
ubuntu@ubuntu:~$ sudo fsck -fv /dev/sda2
fsck z util-linux-ng 2.17.2
fsck: fsck.ntfs: nenalezeno
fsck: Chyba 2 při provádění fsck.ntfs nad /dev/sda2
ubuntu@ubuntu:~$ sudo fsck -fv /dev/sda3
fsck z util-linux-ng 2.17.2
fsck: fsck.swap: nenalezeno
fsck: Chyba 2 při provádění fsck.swap nad /dev/sda3
ubuntu@ubuntu:~$ sudo fsck -fv /dev/sda4
fsck z util-linux-ng 2.17.2
fsck: fsck.ntfs: nenalezeno
fsck: Chyba 2 při provádění fsck.ntfs nad /dev/sda4
Zkusim se jeste podivat na stav disku. Jestli odesel tak mame vyresene tema protoze se pudu utopit.
Jinak tady je vysledek toho co nasel ten skirpt (sdb je usb cudl co jsem pripojil) :
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in
partition #1 for /boot/grub.
=> Syslinux is installed in the MBR of /dev/sdb
sda1: _________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Linux Mint 9 Isadora
Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img
sda2: _________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files/dirs:
sda3: _________________________________________________________________________
File system: swap
Boot sector type: -
Boot sector info:
sda4: _________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files/dirs:
sdb1: _________________________________________________________________________
File system: vfat
Boot sector type: Fat32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files/dirs:
sdb2: _________________________________________________________________________
File system: vfat
Boot sector type: Fat16
Boot sector info: According to the info in the boot sector, sdb2 starts
at sector 0. But according to the info from fdisk,
sdb2 starts at sector 8369865.
Operating System:
Boot files/dirs:
=========================== Drive/Partition Info: =============================
Drive: sda ___________________ _____________________________________________________
Disk /dev/sda: 250,1 GB, 250 059 350 016 bajtů
hlav: 255, sektorů na stopu: 63, cylindrů: 30 401, celkem 488 397 168 sektorů
Jednotky = sektory po 1 * 512 = 512 bajtech
Velikost sektoru (logického/fyzického): 512 bajtů / 512 bajtů
Partition Boot Start End Size Id System
/dev/sda1 * 63 41,945,714 41,945,652 83 Linux
/dev/sda2 41,945,715 83,891,429 41,945,715 7 HPFS/NTFS
/dev/sda3 480,006,135 488,392,064 8,385,930 82 Linux swap / Solaris
/dev/sda4 83,891,430 480,006,134 396,114,705 7 HPFS/NTFS
Drive: sdb ___________________ _____________________________________________________
Disk /dev/sdb: 8 086 MB, 8 086 618 112 bajtů
hlav: 255, sektorů na stopu: 63, cylindrů: 983, celkem 15 794 176 sektorů
Jednotky = sektory po 1 * 512 = 512 bajtech
Velikost sektoru (logického/fyzického): 512 bajtů / 512 bajtů
Partition Boot Start End Size Id System
/dev/sdb1 * 63 8,369,864 8,369,802 6 FAT16
/dev/sdb2 8,369,865 15,791,894 7,422,030 6 FAT16
blkid -c /dev/null: ____________________________________________________________
Device UUID TYPE LABEL
/dev/loop0 squashfs
/dev/sda: PTTYPE="dos"
/dev/sda1 1d2dbcb3-12de-4372-9b51-ec81820da60f ext4
/dev/sda2 54F82EF737095AF8 ntfs windows
/dev/sda3 9e0ec5f1-445b-4b9c-9eb4-8cebe4562a68 swap
/dev/sda4 7A336D433F77A416 ntfs data
/dev/sdb: PTTYPE="dos"
/dev/sdb1 49B1-8C7D vfat
/dev/sdb2 BCEC-0F12 vfat corsair2
============================ "mount | grep ^/dev output: ===========================
Device Mount_Point Type Options
aufs / aufs (rw)
/dev/sr0 /cdrom iso9660 (ro,noatime)
/dev/loop0 /rofs squashfs (ro,noatime)
/dev/sdb2 /media/corsair2 vfat (rw,nosuid,nodev,uhelper=udisks,uid=999,gid=999,shortname=mixed,dmask=0077,utf8=1,flush)
/dev/sdb1 /media/49B1-8C7D vfat (rw,nosuid,nodev,uhelper=udisks,uid=999,gid=999,shortname=mixed,dmask=0077,utf8=1,flush)
=========================== sda1/boot/grub/grub.cfg: ===========================
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by /usr/sbin/grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="0"
if [ ${prev_saved_entry} ]; then
set saved_entry=${prev_saved_entry}
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z ${boot_once} ]; then
saved_entry=${chosen}
save_env saved_entry
fi
}
function recordfail {
set recordfail=1
if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi
}
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
if loadfont /usr/share/grub/unicode.pf2 ; then
set gfxmode=1024x768
#set gfxpayload=keep
insmod gfxterm
insmod vbe
if terminal_output gfxterm ; then true ; else
# For backward compatibility with versions of terminal.mod that don't
# understand terminal_output
terminal gfxterm
fi
fi
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
set locale_dir=($root)/boot/grub/locale
set lang=en
insmod gettext
if [ ${recordfail} = 1 ]; then
set timeout=-1
else
set timeout=10
fi
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
set menu_color_normal=white/black
set menu_color_highlight=black/light-gray
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/06_mint_theme ###
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
insmod png
if background_image /boot/grub/linuxmint.png ; then
set color_normal=white/black
set color_highlight=white/light-gray
else
set menu_color_normal=white/black
set menu_color_highlight=white/light-gray
fi
### END /etc/grub.d/06_mint_theme ###
### BEGIN /etc/grub.d/10_linux ###
menuentry "Linux Mint 9, 2.6.32-24-generic-phc (/dev/sda1)" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux /boot/vmlinuz-2.6.32-24-generic-phc root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro quiet splash
initrd /boot/initrd.img-2.6.32-24-generic-phc
}
menuentry "Linux Mint 9, 2.6.32-24-generic-phc (/dev/sda1) -- recovery mode" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
echo 'Loading Linux 2.6.32-24-generic-phc ...'
linux /boot/vmlinuz-2.6.32-24-generic-phc root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-2.6.32-24-generic-phc
}
menuentry "Linux Mint 9, 2.6.32-24-generic (/dev/sda1)" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux /boot/vmlinuz-2.6.32-24-generic root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro quiet splash
initrd /boot/initrd.img-2.6.32-24-generic
}
menuentry "Linux Mint 9, 2.6.32-24-generic (/dev/sda1) -- recovery mode" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
echo 'Loading Linux 2.6.32-24-generic ...'
linux /boot/vmlinuz-2.6.32-24-generic root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-2.6.32-24-generic
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/10_lupin ###
### END /etc/grub.d/10_lupin ###
### BEGIN /etc/grub.d/20_memtest86+ ###
menuentry "Memory test (memtest86+)" {
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux16 /boot/memtest86+.bin
}
menuentry "Memory test (memtest86+, serial console 115200)" {
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux16 /boot/memtest86+.bin console=ttyS0,115200n8
}
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
if [ ${timeout} != -1 ]; then
if keystatus; then
if keystatus --shift; then
set timeout=-1
else
set timeout=0
fi
else
if sleep --interruptible 3 ; then
set timeout=0
fi
fi
fi
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
=============================== sda1/etc/fstab: ===============================
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s UUID' to print the universally unique identifier
# for a device; this may be used with UUID= as a more robust way to name
# devices that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc nodev,noexec,nosuid 0 0
# / was on /dev/sda1 during installation
UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f / ext4 errors=remount-ro 0 1
# /media/data was on /dev/sda4 during installation
UUID=7A336D433F77A416 /media/data ntfs defaults,nls=utf8,umask=007,gid=46 0 0
# /media/windows was on /dev/sda2 during installation
UUID=54F82EF737095AF8 /media/windows ntfs defaults,nls=utf8,umask=007,gid=46 0 0
# swap was on /dev/sda3 during installation
UUID=9e0ec5f1-445b-4b9c-9eb4-8cebe4562a68 none swap sw 0 0
=================== sda1: Location of files loaded by Grub: ===================
8.7GB: boot/grub/core.img
9.0GB: boot/grub/grub.cfg
10.3GB: boot/initrd.img-2.6.32-24-generic
6.9GB: boot/initrd.img-2.6.32-24-generic-phc
9.5GB: boot/vmlinuz-2.6.32-24-generic
9.2GB: boot/vmlinuz-2.6.32-24-generic-phc
6.9GB: initrd.img
10.3GB: initrd.img.old
9.2GB: vmlinuz
9.5GB: vmlinuz.old
Zkoušel jsi přes recovery mode prostě jen obnovit zavaděč,klasicky příkazem update-grub
Ja se nedostanu ani do Grub menu :-\
Prikladam jeste co jsem nasel v dmesg :
[ 0.923611] ata1: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fff900 irq 22
[ 0.923615] ata2: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fff980 irq 22
[ 0.923619] ata3: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fffa00 irq 22
[ 0.923622] ata4: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fffa80 irq 22
[ 0.923948] scsi4 : pata_atiixp
[ 0.924037] scsi5 : pata_atiixp
[ 0.925112] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 0.925115] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 0.952498] usb 1-2: configuration #1 chosen from 1 choice
[ 0.952701] hub 1-2:1.0: USB hub found
[ 0.952773] hub 1-2:1.0: 4 ports detected
[ 0.976557] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[febff800-febfffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 1.019575] [drm] Initialized drm 1.1.0 20060810
[ 1.088731] ata5.01: ATAPI: BENQ DVD DD DW1625, BBIA, max UDMA/33
[ 1.104685] ata5.01: configured for UDMA/33
[ 1.240050] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.240092] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.328014] usb 2-1: new low speed USB device using ohci_hcd and address 2
[ 1.404026] ata1: softreset failed (device not ready)
[ 1.404029] ata3: softreset failed (device not ready)
[ 1.404033] ata3: applying SB600 PMP SRST workaround and retrying
[ 1.404035] ata1: applying SB600 PMP SRST workaround and retrying
[ 1.500634] usb 2-1: configuration #1 chosen from 1 choice
[ 1.520198] usbcore: registered new interface driver hiddev
[ 1.526781] input: Fujitsu Siemens Computers GmbH FSC KB USB as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.0/input/input3
[ 1.526859] generic-usb 0003:0BF8:1004.0001: input,hidraw0: USB HID v1.10 Keyboard [Fujitsu Siemens Computers GmbH FSC KB USB] on usb-0000:00:13.0-1/input0
[ 1.540584] input: Fujitsu Siemens Computers GmbH FSC KB USB as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.1/input/input4
[ 1.540634] generic-usb 0003:0BF8:1004.0002: input,hidraw1: USB HID v1.10 Device [Fujitsu Siemens Computers GmbH FSC KB USB] on usb-0000:00:13.0-1/input1
[ 1.540659] usbcore: registered new interface driver usbhid
[ 1.540662] usbhid: v2.6:USB HID core driver
[ 1.568033] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.568058] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.569080] ata1.00: ATA-7: Hitachi HDT725025VLA380, V5DOA7DA, max UDMA/100
[ 1.569083] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.569100] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.570315] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.570317] ata1.00: configured for UDMA/100
[ 1.571208] ata3.00: ATAPI: HL-DT-STDVD-RAM GSA-H60N, CX04, max UDMA/100
[ 1.571224] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.575649] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 1.575651] ata3.00: configured for UDMA/100
[ 1.584128] scsi 0:0:0:0: Direct-Access ATA Hitachi HDT72502 V5DO PQ: 0 ANSI: 5
[ 1.584270] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.584385] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.584423] sd 0:0:0:0: [sda] Write Protect is off
[ 1.584426] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.584445] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.584589] sda:
[ 1.599268] scsi 2:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H60N CX04 PQ: 0 ANSI: 5
[ 1.603446] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.603450] Uniform CD-ROM driver Revision: 3.20
[ 1.603538] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 1.603579] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 1.605665] scsi 4:0:1:0: CD-ROM BENQ DVD DD DW1625 BBIA PQ: 0 ANSI: 5
[ 1.612375] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
[ 1.612378] ata1.00: irq_stat 0x08000000, interface fatal error
[ 1.612382] ata1: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
[ 1.612385] ata1.00: failed command: READ FPDMA QUEUED
[ 1.612391] ata1.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
[ 1.612393] res 50/00:08:00:00:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
[ 1.612396] ata1.00: status: { DRDY }
[ 1.612400] ata1: hard resetting link
[ 1.613190] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 1.613263] sr 4:0:1:0: Attached scsi CD-ROM sr1
[ 1.613310] sr 4:0:1:0: Attached scsi generic sg2 type 5
[ 1.772015] usb 3-2: new full speed USB device using ohci_hcd and address 2
[ 1.938951] usb 3-2: configuration #1 chosen from 1 choice
[ 2.028176] usb 1-2.2: new low speed USB device using ehci_hcd and address 5
[ 2.096019] ata1: softreset failed (device not ready)
[ 2.096022] ata1: applying SB600 PMP SRST workaround and retrying
[ 2.142761] usb 1-2.2: configuration #1 chosen from 1 choice
[ 2.153432] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.5/usb1/1-2/1-2.2/1-2.2:1.0/input/input5
[ 2.153650] generic-usb 0003:046D:C518.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.5-2.2/input0
[ 2.159678] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.5/usb1/1-2/1-2.2/1-2.2:1.1/input/input6
[ 2.160194] generic-usb 0003:046D:C518.0004: input,hiddev96,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.5-2.2/input1
[ 2.248266] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c015113b2a2]
[ 2.260033] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.261102] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 2.262005] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 2.262008] ata1.00: revalidation failed (errno=-5)
[ 7.260014] ata1: hard resetting link
[ 7.744016] ata1: softreset failed (device not ready)
[ 7.744019] ata1: applying SB600 PMP SRST workaround and retrying
[ 7.908023] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.909066] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 7.910274] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 7.910276] ata1.00: configured for UDMA/100
[ 7.910286] ata1: EH complete
[ 7.936774] sda1 sda2 sda3 sda4
[ 7.968111] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
[ 7.968113] ata1.00: irq_stat 0x08000000, interface fatal error
[ 7.968117] ata1: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
[ 7.968120] ata1.00: failed command: READ FPDMA QUEUED
[ 7.968125] ata1.00: cmd 60/08:00:f8:4f:9c/00:00:1c:00:00/40 tag 0 ncq 4096 in
[ 7.968126] res 50/00:08:f8:4f:9c/00:00:1c:00:00/40 Emask 0x50 (ATA bus error)
[ 7.968129] ata1.00: status: { DRDY }
[ 7.968132] ata1: hard resetting link
[ 8.452014] ata1: softreset failed (device not ready)
[ 8.452017] ata1: applying SB600 PMP SRST workaround and retrying
[ 8.616030] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8.617075] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 8.618293] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 8.618295] ata1.00: configured for UDMA/100
[ 8.618300] ata1: EH complete
[ 8.634703] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
[ 8.634706] ata1.00: irq_stat 0x08000000, interface fatal error
[ 8.634709] ata1: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
[ 8.634712] ata1.00: failed command: READ FPDMA QUEUED
[ 8.634718] ata1.00: cmd 60/08:00:f8:4f:9c/00:00:1c:00:00/40 tag 0 ncq 4096 in
[ 8.634719] res 50/00:08:f8:4f:9c/00:00:1c:00:00/40 Emask 0x50 (ATA bus error)
[ 8.634722] ata1.00: status: { DRDY }
[ 8.634725] ata1: hard resetting link
[ 9.116021] ata1: softreset failed (device not ready)
[ 9.116023] ata1: applying SB600 PMP SRST workaround and retrying
[ 9.280027] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 9.281084] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 9.282307] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 9.282309] ata1.00: configured for UDMA/100
[ 9.282314] ata1: EH complete
[ 9.301304] ata1: limiting SATA link speed to 1.5 Gbps
[ 9.301307] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
[ 9.301310] ata1.00: irq_stat 0x08000000, interface fatal error
[ 9.301313] ata1: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
[ 9.301316] ata1.00: failed command: READ FPDMA QUEUED
[ 9.301322] ata1.00: cmd 60/08:00:f8:4f:9c/00:00:1c:00:00/40 tag 0 ncq 4096 in
[ 9.301324] res 50/00:08:f8:4f:9c/00:00:1c:00:00/40 Emask 0x50 (ATA bus error)
[ 9.301327] ata1.00: status: { DRDY }
[ 9.301329] ata1: hard resetting link
[ 9.784017] ata1: softreset failed (device not ready)
[ 9.784020] ata1: applying SB600 PMP SRST workaround and retrying
[ 9.948026] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9.949087] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 9.950316] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 9.950319] ata1.00: configured for UDMA/100
[ 9.950323] ata1: EH complete
[ 9.968245] sda: detected capacity change from 0 to 250059350016
-
V LiveCD připojíš sda1 normálně? Jsi schopen procházet soubory na oddíle?
-
Jo normalne pripojim
ubuntu@ubuntu:~$ sudo mount /dev/sda1 /mnt
ubuntu@ubuntu:~$ ls /mnt
bin etc initrd.img.old media proc selinux tmp vmlinuz
boot home lib mnt root srv usr vmlinuz.old
dev initrd.img lost+found opt sbin sys var
ubuntu@ubuntu:~$ ls /mnt/etc
acpi gshadow- pam.d
adduser.conf gtk-2.0 pango
aliases hal papersize
alternatives hddtemp.db passwd
anacrontab hdparm.conf passwd-
apm host.conf pcmcia
apparmor hostname perl
apparmor.d hosts pm
apport hosts.allow pnm2ppa.conf
apt hosts.deny polkit-1
at.deny hp popularity-contest.conf
avahi chatscripts ppp
avrdude.conf chromium-browser printcap
bash.bashrc ifplugd profile
bash.bashrc.save init profile.d
bash_completion init.d protocols
bash_completion.d initramfs-tools pulse
bindresvport.blacklist inputrc purple
blkid.conf insserv python
blkid.tab insserv.conf python2.6
bluetooth insserv.conf.d qt3
bogofilter.cf iproute2 rarfiles.lst
bonobo-activation issue rc.local
brlapi.key issue.dpkg-old rcS.d
brltty issue.net rc0.d
byobu issue.net.dpkg-old rc1.d
ca-certificates java rc2.d
ca-certificates.conf java-6-openjdk rc3.d
calendar java-6-sun rc4.d
compizconfig kbd rc5.d
ConsoleKit kernel rc6.d
console-setup kernel-img.conf request-key.conf
couchdb kerneloops.conf resolvconf
cron.d ldap resolv.conf
cron.daily ld.so.cache rmt
cron.hourly ld.so.conf rpc
cron.monthly ld.so.conf.d rsyslog.conf
crontab legal rsyslog.d
cron.weekly lftp.conf samba
crypttab libao.conf sane.d
cups libpaper.d scanbuttond
cvs-cron.conf linuxmint screenrc
cvs-pserver.conf locale.alias securetty
dbus-1 localtime security
debconf.conf logcheck sensors.d
debian_version login.defs sensors3.conf
default logrotate.conf services
defoma logrotate.d sgml
deluser.conf lsb-base shadow
depmod.d lsb-base-logging.sh shadow-
dhcp3 lsb-release shells
dictionaries-common lsb-release.dpkg-old skel
dkms ltrace.conf smartd.conf
doc-base magic smartmontools
dpkg magic.mime sound
eclipse.ini mailcap speech-dispatcher
emacs mailcap.order spring
environment mail.rc ssh
esmska manpath.config ssl
esound mc sudoers
fancontrol menu sudoers.d
fancontrol_safe menu-methods su-to-rootrc
ffserver.conf mime.types sysctl.conf
firefox mke2fs.conf sysctl.d
firefox-3.0 modprobe.d terminfo
firefox-3.5 modules thunderbird
fonts mono timezone
foomatic motd ts.conf
fstab mplayer ucf.conf
fuse.conf mtab udev
gai.conf mtab.fuselock ufw
gamin mtools.conf updatedb.conf
gconf mysql update-manager
gdb nanorc update-motd.d
gdm ndiswrapper update-notifier
ggi netscsid.conf vga
gimp network vim
gnome NetworkManager wgetrc
gnomenu networks wildmidi
gnome-system-tools nsswitch.conf wodim.conf
gnome-vfs-mime-magic obex-data-server wpa_supplicant
gnome-vfs-2.0 ODBCDataSources w3m
gre.d odbc.ini xdg
groff openal xml
group OpenCL xulrunner-1.9.2
group- openoffice X11
grub.d opt zsh_command_not_found
gshadow pam.conf
ubuntu@ubuntu:~$ sudo cp -r /mnt/etc/apt ./Desktop/
ubuntu@ubuntu:~$ ls ./Desktop/
apt boot_info_script055.sh RESULTS.txt ubiquity-gtkui.desktop
Pisu z Lubuntu LiveCD 10.04
-
Read Error
To je Grub hláška, nebo jiná? Je to přesné a úplné znění?
Pokud použiješ návod
http://forum.ubuntu.cz/index.php/topic,42267.0.html
píše to nějaké chyby?
-
No jak to rict : cerna obrazovka a bile Read error, zkusim udelat reset a poradne si to prohlidnout ale nevypada to na hlasku Grubu.
No sda1 jsem do mnt pripojil, takze kdyz budu pokracovat :
ubuntu@ubuntu:~$ sudo grub-install --root-directory=/mnt/ /dev/sda
// pocitac vrni skrka pocita ...
...//
Installation finished. No error reported.
ubuntu@ubuntu:~$
Tak ja pro klid duse udelam reset a napisu jak sem dopad, ale stejny postup uz jsem provadel.
--------------
Takze beze zmeny. Je to stoprocentne systemova hlaska - nedostanu se ani do Grubu. Vypaluju ted nejaky drive fitness test (http://www.hitachigst.com/support/downloads/#DFT), uvidime
-
Tak ta utilita je sama o sobe dost podivna a, ale kazdopadne mi nahlasila ze disk je vadny. Tak sem zase nabootoval do Lubuntu a spustil GSmartControl a tam spustil Extenden self test a ten probehl uspesne ! Tady je vypis z logu :
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar T7K500
Device Model: Hitachi HDT725025VLA380
Serial Number: VFL161RK017EDF
Firmware Version: V5DOA7DA
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1
Local Time is: Mon Oct 4 21:39:27 2010 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4949) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 83) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 098 098 016 Pre-fail Always - 131075
2 Throughput_Performance 0x0005 161 161 050 Pre-fail Offline - 195
3 Spin_Up_Time 0x0007 119 119 024 Pre-fail Always - 278 (Average 348)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 678
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 134 134 020 Pre-fail Offline - 32
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 853
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 675
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 680
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 680
194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Lifetime Min/Max 17/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 78
SMART Error Log Version: 1
ATA Error Count: 68 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 68 occurred at disk power-on lifetime: 851 hours (35 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 01 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 01 01 00 00 a0 00 05:35:19.600 IDENTIFY DEVICE
25 20 01 01 00 00 00 04 05:35:19.000 READ DMA EXT
25 20 00 00 00 00 e0 ff 05:35:07.000 READ DMA EXT
25 20 01 00 00 00 e0 00 05:33:31.100 READ DMA EXT
25 20 01 00 00 00 e0 00 05:33:31.000 READ DMA EXT
Error 67 occurred at disk power-on lifetime: 851 hours (35 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 6f 59 1c e0 Error: ICRC, ABRT at LBA = 0x001c596f = 1857903
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 01 6f 59 1c e0 00 05:33:28.600 READ DMA EXT
25 20 01 6f 59 1c e0 00 05:33:28.600 READ DMA EXT
37 20 00 6f 59 1c ed 00 05:33:28.600 SET MAX ADDRESS EXT
27 20 01 6f 59 1c e0 00 05:33:28.600 READ NATIVE MAX ADDRESS EXT
ec 20 00 6f 59 1c e0 00 05:33:28.600 IDENTIFY DEVICE
Error 66 occurred at disk power-on lifetime: 851 hours (35 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 51 00 34 21 28 e0 Error: at LBA = 0x00282134 = 2629940
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 34 21 28 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 34 21 28 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 33 21 28 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 32 21 28 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 31 21 28 e0 00 05:32:28.100 READ SECTOR(S) EXT
Error 65 occurred at disk power-on lifetime: 851 hours (35 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 51 00 cf d9 e8 e0 Error: at LBA = 0x00e8d9cf = 15260111
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 cf d9 e8 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 cf d9 e8 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 ce d9 e8 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 cd d9 e8 e0 00 05:32:28.100 READ SECTOR(S) EXT
24 00 01 cc d9 e8 e0 00 05:32:28.100 READ SECTOR(S) EXT
Error 64 occurred at disk power-on lifetime: 851 hours (35 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 0d c2 d9 e8 e9 Error: ABRT at LBA = 0x09e8d9c2 = 166255042
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 10 c0 d9 e8 e0 00 05:32:28.000 READ SECTOR(S) EXT
24 00 01 5f 43 33 e0 00 05:32:28.000 READ SECTOR(S) EXT
24 00 01 5e 43 33 e0 00 05:32:28.000 READ SECTOR(S) EXT
24 00 01 5d 43 33 e0 00 05:32:28.000 READ SECTOR(S) EXT
24 00 01 5c 43 33 e0 00 05:32:28.000 READ SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 853 -
# 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Jdu spustit badblocks a uvidime dal - vysledky budou az zitra.
-
Já vymontoval disk (IDE ext3) a kopíroval pomocí USB převodníku několikrát a nikdy mi to GRUB nepoškodilo.
-
ubuntu@ubuntu:~$ sudo badblocks -vsn /dev/sda1
Hledám špatné bloky v nedestruktivním režimu čtení i zápis
Od bloku 0 do 20972825
Hledám špatné bloky (nedestruktivní test čtení i zápisu)
hotovo lolololololololololo
Průchod dokončen, nalezeno 0 špatných bloků.
ubuntu@ubuntu:~$ sudo badblocks -vsn /dev/sda2
Hledám špatné bloky v nedestruktivním režimu čtení i zápis
Od bloku 0 do 20972856
Hledám špatné bloky (nedestruktivní test čtení i zápisu)
hotovo lolololololololololo
Průchod dokončen, nalezeno 0 špatných bloků.
Je nejaka moznost otestovat MBR na spatne bloky ? Ja proste nmechapu proc to nechce bootovat.
-
To vypadá na nějaký HW problém, zkus ten HDD vypojit/zapojit znovu apod.
Je nejaka moznost otestovat MBR na spatne bloky ?
Mrkni se třeba na výpis (z LiveCD (http://wiki.ubuntu.cz/LiveCD))sudo dd if=/dev/sda bs=512 count=1 | hd
jestli to píše nějaké chyby.
Případně vyfoť tu obrazovku s Read error hláškou.
-
ubuntu@ubuntu:~$ sudo dd if=/dev/sda bs=512 count=1 | hd
00000000 eb 63 90 05 02 00 a3 02 00 00 00 00 00 00 4e 50 |.c............NP|
00000010 fa 33 c0 bc 00 66 8e d0 50 07 50 1f fb fc bf 00 |.3...f..P.P.....|
00000020 08 be 00 7c b9 00 02 f3 a5 50 bf 2f 08 57 cb bb |...|.....P./.W..|
00000030 00 06 be 02 08 0f b6 0c b8 01 02 ba 80 00 cd 13 |................|
00000040 b9 05 00 bb 00 12 be 00 06 03 f1 e8 09 01 eb 0a |................|
00000050 b3 01 be 41 13 88 1c e9 80 00 00 80 01 00 00 00 |...A............|
00000060 00 00 00 00 ff fa 90 90 f6 c2 80 75 02 b2 80 ea |...........u....|
00000070 74 7c 00 00 31 c0 8e d8 8e d0 bc 00 20 fb a0 64 |t|..1....... ..d|
00000080 7c 3c ff 74 02 88 c2 52 bb 17 04 80 27 03 74 06 ||<.t...R....'.t.|
00000090 be 88 7d e8 1c 01 be 05 7c f6 c2 80 74 48 b4 41 |..}.....|...tH.A|
000000a0 bb aa 55 cd 13 5a 52 72 3d 81 fb 55 aa 75 37 83 |..U..ZRr=..U.u7.|
000000b0 e1 01 74 32 31 c0 89 44 04 40 88 44 ff 89 44 02 |..t21..D.@.D..D.|
000000c0 c7 04 10 00 66 8b 1e 5c 7c 66 89 5c 08 66 8b 1e |....f..\|f.\.f..|
000000d0 60 7c 66 89 5c 0c c7 44 06 00 70 b4 42 cd 13 72 |`|f.\..D..p.B..r|
000000e0 05 bb 00 70 eb 76 b4 08 cd 13 73 0d f6 c2 80 0f |...p.v....s.....|
000000f0 84 d0 00 be 93 7d e9 82 00 66 0f b6 c6 88 64 ff |.....}...f....d.|
00000100 40 66 89 44 04 0f b6 d1 c1 e2 02 88 e8 88 f4 40 |@f.D...........@|
00000110 89 44 08 0f b6 c2 c0 e8 02 66 89 04 66 a1 60 7c |.D.......f..f.`||
00000120 66 09 c0 75 4e 66 a1 5c 7c 66 31 d2 66 f7 34 88 |f..uNf.\|f1.f.4.|
00000130 d1 31 d2 66 f7 74 04 3b 44 08 7d 37 fe c1 88 c5 |.1.f.t.;D.}7....|
00000140 30 c0 c1 e8 02 08 c1 88 d0 5a 88 c6 bb 00 70 8e |0........Z....p.|
00000150 c3 31 db b8 01 02 cd 13 72 1e 8c c3 60 1e b9 00 |.1......r...`...|
00000160 01 8e db 31 f6 bf 00 80 8e c6 fc f3 a5 1f 61 ff |...1..........a.|
00000170 26 5a 7c be 8e 7d eb 03 be 9d 7d e8 34 00 be a2 |&Z|..}....}.4...|
00000180 7d e8 2e 00 cd 18 eb fe 47 52 55 42 20 00 47 65 |}.......GRUB .Ge|
00000190 6f 6d 00 48 61 72 64 20 44 69 73 6b 00 52 65 61 |om.Hard Disk.Rea|
000001a0 64 00 20 45 72 72 6f 72 0d 0a 00 bb 01 00 b4 0e |d. Error........|
000001b0 cd 10 ac 3c 00 75 f4 c3 ab 53 92 c0 00 00 80 01 |...<.u...S......|
000001c0 01 00 83 fe ff ff 3f 00 00 00 34 0a 80 02 00 fe |......?...4.....|
000001d0 ff ff 07 fe ff ff 73 0a 80 02 73 0a 80 02 00 fe |......s...s.....|
000001e0 ff ff 82 fe ff ff f7 4f 9c 1c 8a f5 7f 00 00 fe |.......O........|
000001f0 ff ff 07 fe ff ff e6 14 00 05 11 3b 9c 17 55 aa |...........;..U.|
00000200
1+0 vstoupivších záznamů
1+0 vystoupivších záznamů
512 bajtů (512 B) zkopírováno, 0,00141923 s, 361 kB/s
Na tom neni nic k foceni, cerna obrazovka a klasickym dosackym pismem Read Error - vlevo nahore, nic vic , nic min. Pokud necham bootovat z disku nebo pokud dam v menu LIveCD nabootovat z prvniho disku. Zkusim nejdriv pomoci DD udelat klon disku a pak zkusim disk vypojit a zapojit, púroc by ale jinak sel bez potizi pripojit, proc by z nej slo cist, testy vsechny probehly v poradku .... ja to nechapu.
-
Zas'')§)§*{}&\ pode@!#$%%^^ LENOVO
Tak resetuju a najednou mi to napise tohle - ihned na zacatku pri post procedure kde se detekujou disky :
harddisk locked, enter user pawword
press ESC to switch to master password
...
continue booting with this drive being locked may cause system to hang
...
3rd master harddisk SMART command failed, F2 continue,F1 setup
Toto se mi stalo pote, co jsem pripojil jiny sata disk prez usb redukci a udelal reset, takze tezko rict NA KTERY disk se to vztahuje. Problem je ze kdyz pripojim novy 500GB SATA disk prez USB redukci a pripojim ji , tak dmesg napise :
[ 773.777130] scsi 7:0:0:0: Direct-Access PQ: 0 ANSI: 2 CCS
[ 773.778654] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 773.790745] sd 7:0:0:0: [sdb] Attached SCSI disk
ale disk nemuzu najit:
ubuntu@ubuntu:~$ sudo fdisk -l
Disk /dev/sda: 250,1 GB, 250 059 350 016 bajtů
hlav: 255, sektorů na stopu: 63, cylindrů: 30 401
Jednotky = cylindry po 16065 * 512 = 8 225 280 bajtech
Velikost sektoru (logického/fyzického): 512 bajtů / 512 bajtů
Velikost I/O (minimální/optimální): 512 bajtů / 512 bajtů
Identifikátor disku: 0xc09253ab
Zařízení Zavádět Začátek Konec Bloky Id Systém
/dev/sda1 * 1 2611 20972826 83 Linux
/dev/sda2 2612 5222 20972857+ 7 HPFS/NTFS
/dev/sda3 29880 30401 4192965 82 Linux swap/Solaris
/dev/sda4 5223 29879 198057352+ 7 HPFS/NTFS
Diskové oddíly jsou chybně seřazeny
Parted ani gparted nic nevidi a stejnak nemuzu pouzit dd, pricemz ale :
ubuntu@ubuntu:~$ ls /dev
admmidi kmsg ram2 stdout tty34 tty8
adsp log ram3 tty tty35 tty9
amidi loop0 ram4 ttyS0 tty36 urandom
audio loop1 ram5 ttyS1 tty37 usb
block loop2 ram6 ttyS2 tty38 usbmon0
bsg loop3 ram7 ttyS3 tty39 usbmon1
bus loop4 ram8 tty0 tty4 usbmon2
cdrom loop5 ram9 tty1 tty40 usbmon3
cdrom1 loop6 random tty10 tty41 usbmon4
cdrw loop7 rfkill tty11 tty42 usbmon5
cdrw1 mapper rtc tty12 tty43 usbmon6
console mcelog rtc0 tty13 tty44 vcs
core mem scd0 tty14 tty45 vcsa
cpu_dma_latency midi scd1 tty15 tty46 vcsa1
disk mixer sda tty16 tty47 vcsa2
dmmidi net sda1 tty17 tty48 vcsa3
dri network_latency sda2 tty18 tty49 vcsa4
dsp network_throughput sda3 tty19 tty5 vcsa5
dvd null sda4 tty2 tty50 vcsa6
dvdrw oldmem sdb tty20 tty51 vcsa7
dvdrw1 pktcdvd sequencer tty21 tty52 vcs1
dvd1 port sequencer2 tty22 tty53 vcs2
ecryptfs ppp sg0 tty23 tty54 vcs3
fb0 psaux sg1 tty24 tty55 vcs4
fd ptmx sg2 tty25 tty56 vcs5
full pts sg3 tty26 tty57 vcs6
fuse ram0 shm tty27 tty58 vcs7
hidraw0 ram1 snapshot tty28 tty59 vga_arbiter
hidraw1 ram10 snd tty29 tty6 zero
hidraw2 ram11 sndstat tty3 tty60
hidraw3 ram12 sr0 tty30 tty61
hpet ram13 sr1 tty31 tty62
char ram14 stderr tty32 tty63
input ram15 stdin tty33 tty7
Jdu studovat tu hlasku - v BIOSU jsem mel vsechny security featury vypnuty, ani bios neni pod heslem, bios se nedavno resetil po vymnene baterky ... ja uz vazne nevim.
-
Znacim jako vyreseno - i kdyz vyreseno to neni.
Pomoci dd sem prehodil cely disk na jiny a ten okamzite nabootoval. Spis nez HW chyba disku se jedna o to ze se nejakym zpusobem zaktivovalo zaheslovani disku podle ATA standartu nebo co ... nechapu a hlavne co s tim ted. Navic je to Hitachi disk na ktery ruzne unlock-programky nestaci.Problem je ze delam na Thinkcenter masine kterou Lenovo vybavilo spoustou opicaren vhodnych do firemniho prostredi ale jinak to ma BIOS k nicemu, poradne si tam nc nenastavite. V biosu je kolonka na zmenu hesla HDD ale je neaktivni - seda a na internetu najdete prispevky do Lenovo fora kde to lide resili tim ze poslali MB na vymenu v ramci reklamace ... na palici
Takze budu zkouset prehrat firmware harddisku, parada :-\ No nic diky vsem za pomoc K
-
pokud si dobře pamatuju tak se to řešilo - downgrade biosu, změna a odinstalace hesla, upgrade biosu
//edit: pamatuju: http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=SF10-D0121 (http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=SF10-D0121)
-
D I KY ! Jestli to bude fungovat napiste adresu a poslu cukrovinky ! ;D
-
Tak ja nevim jestli to bylo tim zaheslovanim, pro jistotu jsem dal starou verzi BIOSU, dal prazdne heslo jednotky - napsalo mi to heslo deaktivovani - a nahraj BIOS aktualni.
Parada az sem dobre.
Pred tim jsem pomoci dd zklopil ten disk na jiny a z neho mohl bootovat tak jak jsem byl zvykly, tak jsem to ted zkousel obracene a bez uspechu. Nainstaloval jsem na ten problemovy disk pro jistotu ciste Ubuntu 10.04 a nabootovalo to krasne !!! ???
Tak jsem pomoci aktualni Clonezilly preklopil ten zalozni disk zase na ten problemovy a vypsalo mi to :
error hd0,1 out of disk
ale aspon uz na me ted blika
grub Rescue>
Zkousel jsem tento navod (http://superuser.com/questions/89307/grub2-error-out-of-disk) a u radku :
insmod /boot/grub/linux.mod
mi to zase vypsalo : out of disk hd0,1
ACHJOOOO co ja komu proved !!! Tak sem tam vrazil LiveCD a dal nabootovat z prvniho disku - a system se opravdu zavedl !!!
Takze jsem zkusil
sudo grub-install
sudo update-grub2
Nevypsalo mi to zadne hcybove hlasky a po resetu ...
error hd0,1 out of disk
:'( :-\ :'( ??? UAAAAAAAAA !!!!!!!
SOS spaste moji dusi
-
Dej tady výpis z boot_info_script (http://wiki.ubuntu.cz/boot_info_script).
-
-Vcera jsem zkousel opravit Grub pomoci Rescatuxu - byvaleho supergrubdisku - ted mi to hazi uz jen
out of disk
bez udani hd0,1
Pomoci LiveCD ale aspon zavedu system. Tady je vypis toho skriptu :
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in
partition #1 for /boot/grub.
=> Syslinux is installed in the MBR of /dev/sdb
sda1: _________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Linux Mint 9 Isadora
Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img
sda2: _________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files/dirs:
sda3: _________________________________________________________________________
File system: swap
Boot sector type: -
Boot sector info:
sda4: _________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files/dirs:
sdb1: _________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files/dirs:
=========================== Drive/Partition Info: =============================
Drive: sda ___________________ _____________________________________________________
Platte /dev/sda: 250.1 GByte, 250059350016 Byte
255 Köpfe, 63 Sektoren/Spur, 30401 Zylinder, zusammen 488397168 Sektoren
Einheiten = Sektoren von 1 × 512 = 512 Bytes
Sector size (logical/physical): 512 bytes / 512 bytes
Partition Boot Start End Size Id System
/dev/sda1 * 63 41,945,714 41,945,652 83 Linux
/dev/sda2 41,945,715 83,891,429 41,945,715 7 HPFS/NTFS
/dev/sda3 480,006,135 488,392,064 8,385,930 82 Linux swap / Solaris
/dev/sda4 83,891,430 480,006,134 396,114,705 7 HPFS/NTFS
Drive: sdb ___________________ _____________________________________________________
Platte /dev/sdb: 8086 MByte, 8086618112 Byte
255 Köpfe, 63 Sektoren/Spur, 983 Zylinder, zusammen 15794176 Sektoren
Einheiten = Sektoren von 1 × 512 = 512 Bytes
Sector size (logical/physical): 512 bytes / 512 bytes
Partition Boot Start End Size Id System
/dev/sdb1 63 15,791,894 15,791,832 7 HPFS/NTFS
blkid -c /dev/null: ____________________________________________________________
Device UUID TYPE LABEL
/dev/ramzswap0 swap
/dev/sda1 1d2dbcb3-12de-4372-9b51-ec81820da60f ext4
/dev/sda2 54F82EF737095AF8 ntfs windows
/dev/sda3 9e0ec5f1-445b-4b9c-9eb4-8cebe4562a68 swap
/dev/sda4 7A336D433F77A416 ntfs data
/dev/sda: PTTYPE="dos"
/dev/sdb1 3BBCE43050BE53D5 ntfs Corsair Survivor
/dev/sdb: PTTYPE="dos"
============================ "mount | grep ^/dev output: ===========================
Device Mount_Point Type Options
/dev/sda1 / ext4 (rw,errors=remount-ro)
/dev/sda4 /media/data fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions)
/dev/sda2 /media/windows fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions)
/dev/sr0 /media/disk iso9660 (ro,nosuid,nodev,uhelper=udisks,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500)
/dev/sdb1 /media/Corsair Survivor fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions)
=========================== sda1/boot/grub/grub.cfg: ===========================
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by /usr/sbin/grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="0"
if [ ${prev_saved_entry} ]; then
set saved_entry=${prev_saved_entry}
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z ${boot_once} ]; then
saved_entry=${chosen}
save_env saved_entry
fi
}
function recordfail {
set recordfail=1
if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi
}
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
if loadfont /usr/share/grub/unicode.pf2 ; then
set gfxmode=1024x768
#set gfxpayload=keep
insmod gfxterm
insmod vbe
if terminal_output gfxterm ; then true ; else
# For backward compatibility with versions of terminal.mod that don't
# understand terminal_output
terminal gfxterm
fi
fi
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
set locale_dir=($root)/boot/grub/locale
set lang=de
insmod gettext
if [ ${recordfail} = 1 ]; then
set timeout=-1
else
set timeout=10
fi
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
set menu_color_normal=white/black
set menu_color_highlight=black/light-gray
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/06_mint_theme ###
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
insmod png
if background_image /boot/grub/linuxmint.png ; then
set color_normal=white/black
set color_highlight=white/light-gray
else
set menu_color_normal=white/black
set menu_color_highlight=white/light-gray
fi
### END /etc/grub.d/06_mint_theme ###
### BEGIN /etc/grub.d/10_linux ###
menuentry "Linux Mint 9, 2.6.32-25-generic-phc (/dev/sda1)" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux /boot/vmlinuz-2.6.32-25-generic-phc root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro quiet splash
initrd /boot/initrd.img-2.6.32-25-generic-phc
}
menuentry "Linux Mint 9, 2.6.32-25-generic-phc (/dev/sda1) -- recovery mode" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
echo 'Linux 2.6.32-25-generic-phc wird geladen …'
linux /boot/vmlinuz-2.6.32-25-generic-phc root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro single
echo 'Initiale Ramdisk wird geladen …'
initrd /boot/initrd.img-2.6.32-25-generic-phc
}
menuentry "Linux Mint 9, 2.6.32-25-generic (/dev/sda1)" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux /boot/vmlinuz-2.6.32-25-generic root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro quiet splash
initrd /boot/initrd.img-2.6.32-25-generic
}
menuentry "Linux Mint 9, 2.6.32-25-generic (/dev/sda1) -- recovery mode" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
echo 'Linux 2.6.32-25-generic wird geladen …'
linux /boot/vmlinuz-2.6.32-25-generic root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro single
echo 'Initiale Ramdisk wird geladen …'
initrd /boot/initrd.img-2.6.32-25-generic
}
menuentry "Linux Mint 9, 2.6.32-24-generic-phc (/dev/sda1)" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux /boot/vmlinuz-2.6.32-24-generic-phc root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro quiet splash
initrd /boot/initrd.img-2.6.32-24-generic-phc
}
menuentry "Linux Mint 9, 2.6.32-24-generic-phc (/dev/sda1) -- recovery mode" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
echo 'Linux 2.6.32-24-generic-phc wird geladen …'
linux /boot/vmlinuz-2.6.32-24-generic-phc root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro single
echo 'Initiale Ramdisk wird geladen …'
initrd /boot/initrd.img-2.6.32-24-generic-phc
}
menuentry "Linux Mint 9, 2.6.32-24-generic (/dev/sda1)" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux /boot/vmlinuz-2.6.32-24-generic root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro quiet splash
initrd /boot/initrd.img-2.6.32-24-generic
}
menuentry "Linux Mint 9, 2.6.32-24-generic (/dev/sda1) -- recovery mode" --class linuxmint --class gnu-linux --class gnu --class os {
recordfail
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
echo 'Linux 2.6.32-24-generic wird geladen …'
linux /boot/vmlinuz-2.6.32-24-generic root=UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f ro single
echo 'Initiale Ramdisk wird geladen …'
initrd /boot/initrd.img-2.6.32-24-generic
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/10_lupin ###
### END /etc/grub.d/10_lupin ###
### BEGIN /etc/grub.d/20_memtest86+ ###
menuentry "Memory test (memtest86+)" {
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux16 /boot/memtest86+.bin
}
menuentry "Memory test (memtest86+, serial console 115200)" {
insmod ext2
set root='(hd0,1)'
search --no-floppy --fs-uuid --set 1d2dbcb3-12de-4372-9b51-ec81820da60f
linux16 /boot/memtest86+.bin console=ttyS0,115200n8
}
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
if [ ${timeout} != -1 ]; then
if keystatus; then
if keystatus --shift; then
set timeout=-1
else
set timeout=0
fi
else
if sleep --interruptible 3 ; then
set timeout=0
fi
fi
fi
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
=============================== sda1/etc/fstab: ===============================
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s UUID' to print the universally unique identifier
# for a device; this may be used with UUID= as a more robust way to name
# devices that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc nodev,noexec,nosuid 0 0
# / was on /dev/sda1 during installation
UUID=1d2dbcb3-12de-4372-9b51-ec81820da60f / ext4 errors=remount-ro 0 1
# /media/data was on /dev/sda4 during installation
UUID=7A336D433F77A416 /media/data ntfs defaults,nls=utf8,umask=007,gid=46 0 0
# /media/windows was on /dev/sda2 during installation
UUID=54F82EF737095AF8 /media/windows ntfs defaults,nls=utf8,umask=007,gid=46 0 0
# swap was on /dev/sda3 during installation
UUID=9e0ec5f1-445b-4b9c-9eb4-8cebe4562a68 none swap sw 0 0
=================== sda1: Location of files loaded by Grub: ===================
8.7GB: boot/grub/core.img
.5GB: boot/grub/grub.cfg
10.3GB: boot/initrd.img-2.6.32-24-generic
6.9GB: boot/initrd.img-2.6.32-24-generic-phc
7.3GB: boot/initrd.img-2.6.32-25-generic
5.6GB: boot/initrd.img-2.6.32-25-generic-phc
9.5GB: boot/vmlinuz-2.6.32-24-generic
9.2GB: boot/vmlinuz-2.6.32-24-generic-phc
10.8GB: boot/vmlinuz-2.6.32-25-generic
5.2GB: boot/vmlinuz-2.6.32-25-generic-phc
5.6GB: initrd.img
7.3GB: initrd.img.old
5.2GB: vmlinuz
10.8GB: vmlinuz.old
Zatim tam mam jen na /sda1 Mint 9, Win7 jsem jeste ani nestacil nahrat, to bude asi jeste legrace ... :-\
Jdu ted zkusit jeste nejaky navod na obnovu GRubu z beziciho systemu
---------
EDIT :
;D ;D ;D ;D ;D ;D ;D ;D ;D
JOOOOO !!!!
Moje trapeni ukoncilo :
sudo apt-get install grub-common grub-pc os-prober --reinstall
Probuh CO BYLO SPATNE ? Tak nejsem uz uplna lama lama dalajlama ale ... nejdriv "jen vyndam disk", po vlozeni disk nechce bootovat ani je li mucen, po ruznem X-tem prehrani puvodnich dat a nahrani ciste instalace najednou bootuje, pak zase Grub dela divy ze zrak prechazi .. ???
No nevadi alespon muzu uklidit vsechny rozhazeny CDcka, pridelat bocnici,dat pocitac zase na misto ... Ten disk tam asi privarim at uz se nikdy nepohne.
Ale stejnak vsem moc dekuju za rady
-
Abych se neradoval predcasne ...
Zmenil jsem si jen rozliseni pri bootu : Menu -> Administrace - Startup-Manager dam reset ...
Error: hd0,1 out of disk
Error: hd0,1 out of disk
VGA=792 is deprecated, ude GFXpayload ...
Kernel panic - not Syncing : VFS unable to mount root fs on uknown block(0,0)
Takze reset (1) - boot prez LiveCD - bez uspechu
Znovu, reset (2) liveCD - system bootuje
reset (3) bez Live CD - system bootuje
reset (4) bez Live CD - system bootuje se spravnym rozlisneim !
reset (5) error: hd0,1 out of disk
...
VGA=792 is ...
zasek
reset (6) - skoncim v Grub rescue >
reset (7) - SYSTEM BOOTUJE
OMG WTF .... buuu beee (brek,zoufalstvi...)
Co jsem nasel v dmesg :
[ 4.759715] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
[ 4.759719] ata1.00: irq_stat 0x08000000, interface fatal error
[ 4.759724] ata1: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
[ 4.759727] ata1.00: failed command: READ FPDMA QUEUED
[ 4.759733] ata1.00: cmd 60/08:00:68:59:1c/00:00:1d:00:00/40 tag 0 ncq 4096 in
[ 4.759734] res 50/00:08:68:59:1c/00:00:1d:00:00/40 Emask 0x50 (ATA bus error)
[ 4.759737] ata1.00: status: { DRDY }
[ 4.759741] ata1: hard resetting link
[ 5.240017] ata1: softreset failed (device not ready)
[ 5.240020] ata1: applying SB600 PMP SRST workaround and retrying
[ 5.404056] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.405123] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 5.406358] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 5.406361] ata1.00: configured for UDMA/100
[ 5.406369] ata1: EH complete
[ 5.432131] ata1: limiting SATA link speed to 1.5 Gbps
[ 5.432135] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
[ 5.432137] ata1.00: irq_stat 0x08000000, interface fatal error
[ 5.432140] ata1: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
[ 5.432143] ata1.00: failed command: READ FPDMA QUEUED
[ 5.432148] ata1.00: cmd 60/08:00:b8:55:1c/00:00:1d:00:00/40 tag 0 ncq 4096 in
[ 5.432149] res 50/00:08:b8:55:1c/00:00:1d:00:00/40 Emask 0x50 (ATA bus error)
[ 5.432152] ata1.00: status: { DRDY }
[ 5.432156] ata1: hard resetting link
[ 5.916019] ata1: softreset failed (device not ready)
[ 5.916023] ata1: applying SB600 PMP SRST workaround and retrying
[ 6.080027] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 6.081098] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 6.082341] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 6.082343] ata1.00: configured for UDMA/100
[ 6.082351] ata1: EH complete
[ 6.223174] EXT4-fs (sda1): mounted filesystem with ordered data mode
A tady jeste jednou sudo dd if=/dev/sda bs=512 count=1 | hd
00000000 eb 63 90 05 02 00 a3 02 00 00 00 00 00 00 4e 50 |.c............NP|
00000010 fa 33 c0 bc 00 66 8e d0 50 07 50 1f fb fc bf 00 |.3...f..P.P.....|
00000020 08 be 00 7c b9 00 02 f3 a5 50 bf 2f 08 57 cb bb |...|.....P./.W..|
00000030 00 06 be 02 08 0f b6 0c b8 01 02 ba 80 00 cd 13 |................|
00000040 b9 05 00 bb 00 12 be 00 06 03 f1 e8 09 01 eb 0a |................|
00000050 b3 01 be 41 13 88 1c e9 80 00 00 80 01 00 00 00 |...A............|
00000060 00 00 00 00 ff fa 90 90 f6 c2 80 75 02 b2 80 ea |...........u....|
00000070 74 7c 00 00 31 c0 8e d8 8e d0 bc 00 20 fb a0 64 |t|..1....... ..d|
00000080 7c 3c ff 74 02 88 c2 52 bb 17 04 80 27 03 74 06 ||<.t...R....'.t.|
00000090 be 88 7d e8 1c 01 be 05 7c f6 c2 80 74 48 b4 41 |..}.....|...tH.A|
000000a0 bb aa 55 cd 13 5a 52 72 3d 81 fb 55 aa 75 37 83 |..U..ZRr=..U.u7.|
000000b0 e1 01 74 32 31 c0 89 44 04 40 88 44 ff 89 44 02 |..t21..D.@.D..D.|
000000c0 c7 04 10 00 66 8b 1e 5c 7c 66 89 5c 08 66 8b 1e |....f..\|f.\.f..|
000000d0 60 7c 66 89 5c 0c c7 44 06 00 70 b4 42 cd 13 72 |`|f.\..D..p.B..r|
000000e0 05 bb 00 70 eb 76 b4 08 cd 13 73 0d f6 c2 80 0f |...p.v....s.....|
000000f0 84 d0 00 be 93 7d e9 82 00 66 0f b6 c6 88 64 ff |.....}...f....d.|
00000100 40 66 89 44 04 0f b6 d1 c1 e2 02 88 e8 88 f4 40 |@f.D...........@|
00000110 89 44 08 0f b6 c2 c0 e8 02 66 89 04 66 a1 60 7c |.D.......f..f.`||
00000120 66 09 c0 75 4e 66 a1 5c 7c 66 31 d2 66 f7 34 88 |f..uNf.\|f1.f.4.|
00000130 d1 31 d2 66 f7 74 04 3b 44 08 7d 37 fe c1 88 c5 |.1.f.t.;D.}7....|
00000140 30 c0 c1 e8 02 08 c1 88 d0 5a 88 c6 bb 00 70 8e |0........Z....p.|
00000150 c3 31 db b8 01 02 cd 13 72 1e 8c c3 60 1e b9 00 |.1......r...`...|
00000160 01 8e db 31 f6 bf 00 80 8e c6 fc f3 a5 1f 61 ff |...1..........a.|
00000170 26 5a 7c be 8e 7d eb 03 be 9d 7d e8 34 00 be a2 |&Z|..}....}.4...|
00000180 7d e8 2e 00 cd 18 eb fe 47 52 55 42 20 00 47 65 |}.......GRUB .Ge|
00000190 6f 6d 00 48 61 72 64 20 44 69 73 6b 00 52 65 61 |om.Hard Disk.Rea|
1+0 Datensätze ein
1+0 Datensätze aus
000001a0 64 00 20 45 72 72 6f 72 0d 0a 00 bb 01 00 b4 0e |d. Error........|
000001b0 cd 10 ac 3c 00 75 f4 c3 ab 53 92 c0 00 00 80 01 |...<.u...S......|
512 Bytes (512 B) kopiert000001c0 01 00 83 fe ff ff 3f 00 00 00 34 0a 80 02 00 fe |......?...4.....|
000001d0 ff ff 07 fe ff ff 73 0a 80 02 73 0a 80 02 00 fe |......s...s.....|
, 7,92e-05 s, 6,5 MB/s
000001e0 ff ff 82 fe ff ff f7 4f 9c 1c 8a f5 7f 00 00 fe |.......O........|
000001f0 ff ff 07 fe ff ff e6 14 00 05 11 3b 9c 17 55 aa |...........;..U.|
00000200
-
Zkusmo jsem vymnenil SATA kablik a problemy ustaly.
Jdu se nekam vybrecet do kouta :'(
-
Tak poškozený SATA kabel mi tohle taky dělal,jenom na mechanice,vždycky jednou za čas mi prostě přestala načítat media,taky jsem z toho skoro skončil v blázinci než jsem na to přišel
-
No ono je to ted takovy ruzny nekdy ano nekdy ne ... uz sem se i dival na ten disk jeslti tam neni vaklkontakt u tech SATA konektoru, pak jsem to pripojil k externi USB redukci - ta s tim nechtela mic NIC spolecnyho, proste seani neinicializovalo zarizeni, pak jsem ten disk strcil do externiho USB boxu tam se chyt, pak v pocitaci hned na prvni pokus ...
Podle me je mozna elektronika v pekle - vadny sektory zadny, SMART test taky OK jen se ten disk po vypnuti nekdy vubec nechyti nebo nechce bootovat ale kdyz se chyti tak pracuje spravne. Jenze jak tohle testovat zejo ....
-
To nejde,taky tu mám jeden notebookový disk od Hitachi,testem na vadné sektory projde v pohodě,smartem i tím dlouhým taky,ale jakmile na něj začnu kopírovat větší množství dat,tak se prostě zasekne a přestane zapisovat (ovšem testem zápisu taky projde).Filesystem jsem na něm taky několikrát změnil,asi bude ta elektronika chycená,ale testama prostě projde
-
Tak diky vsem uz to tu uzaviram ... to je v pr... :(