Dobrý den,
mám dojem, že mám něco špatného s diskem, protože se nechová tak, jak by měl. Po výpisu SMARTu jsem objevil toto: READ FPDMA QUEUED u odstavců: Error 6594 occurred at disk power-on lifetime
O co se jedná? Mohu dále používat svůj disk- např. po low-level formátu, nebo hrozí nebezpečí, že teď o data na disku příjdu?
Děkuji za odpovědi
ubuntu@ubuntu:~$ sudo smartctl -a /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio family
Device Model: WDC WD2500BEVS-22UST0
Serial Number: WD-WXE907G63729
Firmware Version: 01.01A01
User Capacity: 250 059 350 016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Jun 28 23:13:38 2010 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (8760) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 3
3 Spin_Up_Time 0x0003 189 186 021 Pre-fail Always - 1525
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3928
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 8049
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3503
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 397
193 Load_Cycle_Count 0x0032 164 164 000 Old_age Always - 110600
194 Temperature_Celsius 0x0022 093 076 000 Old_age Always - 54
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 197 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 197 197 000 Old_age Offline - 161
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 197 197 051 Pre-fail Offline - 199
SMART Error Log Version: 1
ATA Error Count: 6598 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6598 occurred at disk power-on lifetime: 8043 hours (335 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 40 d8 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 07 38 b1 48 56 12 00 00:09:03.995 READ FPDMA QUEUED
60 1a 30 e5 d2 79 12 00 00:09:03.982 READ FPDMA QUEUED
60 20 28 c5 d2 79 12 00 00:09:03.982 READ FPDMA QUEUED
60 20 28 a5 d2 79 12 00 00:09:03.981 READ FPDMA QUEUED
60 20 18 85 d2 79 12 00 00:09:03.980 READ FPDMA QUEUED
Error 6597 occurred at disk power-on lifetime: 8043 hours (335 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 40 d8 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 20 54 75 66 12 00 00:08:59.468 READ FPDMA QUEUED
60 49 18 32 6c 6d 12 00 00:08:59.468 READ FPDMA QUEUED
60 10 10 00 40 d8 11 00 00:08:59.468 READ FPDMA QUEUED
60 20 08 18 f5 63 12 00 00:08:59.468 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 00:08:59.468 SET FEATURES [Enable write cache]
Error 6596 occurred at disk power-on lifetime: 8043 hours (335 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 40 d8 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 68 84 76 66 12 00 00:08:54.895 READ FPDMA QUEUED
60 08 60 54 75 66 12 00 00:08:54.895 READ FPDMA QUEUED
60 d0 58 fe 08 55 12 00 00:08:54.895 READ FPDMA QUEUED
60 08 50 03 d9 63 12 00 00:08:54.895 READ FPDMA QUEUED
60 09 48 fa d8 63 12 00 00:08:54.895 READ FPDMA QUEUED
Error 6595 occurred at disk power-on lifetime: 8043 hours (335 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 40 d8 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 88 84 76 66 12 00 00:08:50.593 READ FPDMA QUEUED
60 08 80 54 75 66 12 00 00:08:50.593 READ FPDMA QUEUED
60 d0 78 fe 08 55 12 00 00:08:50.593 READ FPDMA QUEUED
60 08 70 03 d9 63 12 00 00:08:50.593 READ FPDMA QUEUED
60 09 68 fa d8 63 12 00 00:08:50.570 READ FPDMA QUEUED
Error 6594 occurred at disk power-on lifetime: 8043 hours (335 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 40 d8 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 38 ca 71 51 12 00 00:08:46.385 READ FPDMA QUEUED
60 49 30 32 6c 6d 12 00 00:08:46.384 READ FPDMA QUEUED
60 08 28 2a 08 52 12 00 00:08:46.384 READ FPDMA QUEUED
60 3b 20 5d f0 63 12 00 00:08:46.384 READ FPDMA QUEUED
60 10 18 00 40 d8 11 00 00:08:46.384 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8049 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Téma: READ FPDMA QUEUED??? (Přečteno 2210 krát)
