Jak identifikovat slabé místo v sestavě?

[ondrejkovic]

Ahoj, mám poskládané PC - procesor AMD Athlon XP 2500+ 1,5 GB RAM, HDD IDE 300 GB, Základní deska ECS K7VTA3, grafická karta ATI RV350 (Radeon 9600) s 256 MB RAM. Celé to jede na stejném SW (momentálně Ubuntu 10.04) citelně pomaleji než můj notebook se slabším procesorem, menším množstvím RAM i když se samostatnou grafikou (taky ATI). Hlavně mám pocit, že vázne překreslování obrazovky, ale taky konverze videa je o něco delší.

Žádné ovladače třetí strany mi systém nenabízí, v minulosti jsem zkoušel něco stáhnout i ze stránek ATI, ale zhavaroval celý počítač.

Jsem lama - tedy běžný kancelářský uživatel, který si sice umí nainstalovat Ubuntu a provozovat ho (nehraju hry), ale slova jako kompilace apod u mne vzbuzují posvátnou úctu a i když jsem několikrát použil slova jako ./configure - make - make install, tak při jakékoli chybě si už rady nevím.

Jak mohu identifikovat slabé místo ve svém počítači? Prosím pokud odpovíte - přizpůsobte pochopitelnost výše popsanému stavu. Děkuji za pochopení.

[TIBOR]

Otazka je aku konfiguraciu ma tvoj ntb. Ide o to ze ak ma procesor v ntb nizsiu frekvenciu ako ten v zostave, ovsem je modernejsi tak moze byt ovela vykonnejsi. To iste RAM ak mas v ntb menej RAM ovsem ide na frekvencii 800MHz a v zostave mas viac RAM ale ide na 667MHz tiez bude ta v ntb vykonnejsia.
Cize, takto tazko povedat.

[ondrejkovic]

A existuje nějaký příkaz do terminálu, který by vypsal kompletní konfiguraci? Nebo nějaký prográmek.

[TIBOR]

lspci
lsusb
lshw
sudo lshw
hwinfo
alebo program tusim
lshw-gtk
hardinfo

[ondrejkovic]

Tak - přijde někdo z vás na to kde je v této sestavě úzké hrdlo? Já jsem z toho dost jelen:


  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0303
  Config Status: cfg=new, avail=yes, need=no, active=unknown

41: None 00.0: 0700 Serial controller
  [Created at misc.449]
  Unique ID: rdCR.7RG8lK_UzJ9
  Hardware Class: unknown
  Model: "Serial controller"
  I/O Ports: 0x3f8-0x3ff (rw)
  IRQ: 4 (1 event)
  Config Status: cfg=new, avail=yes, need=no, active=unknown

42: IDE 00.0: 10600 Disk
  [Created at block.243]
  UDI: /org/freedesktop/Hal/devices/storage_serial_ST3320620A_9QF3GBGS
  Unique ID: 3OOL.VXhFutAVWLA
  Parent ID: +Y+h.mcsZ0a690T4
  SysFS ID: /class/block/sda
  SysFS BusID: 0:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:11.1/host0/target0:0:0/0:0:0:0
  Hardware Class: disk
  Model: "ST3320620A"
  Device: "ST3320620A"
  Revision: "3.AA"
  Driver: "pata_via", "sd"
  Driver Modules: "pata_via"
  Device File: /dev/sda
  Device Files: /dev/sda, /dev/block/8:0, /dev/disk/by-id/ata-ST3320620A_9QF3GBGS, /dev/disk/by-id/scsi-SATA_ST3320620A_9QF3GBGS, /dev/disk/by-path/pci-0000:00:11.1-scsi-0:0:0:0
  Device Number: block 8:0-8:15
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #23 (IDE interface)

43: None 00.0: 11300 Partition
  [Created at block.412]
  UDI: /org/freedesktop/Hal/devices/volume_uuid_f34b9fab_95bf_4ec9_a19b_38c650503d10
  Unique ID: bdUI.SE1wIdpsiiC
  Parent ID: 3OOL.VXhFutAVWLA
  SysFS ID: /class/block/sda/sda1
  Hardware Class: partition
  Model: "Partition"
  Device File: /dev/sda1
  Device Files: /dev/sda1, /dev/block/8:1, /dev/disk/by-id/ata-ST3320620A_9QF3GBGS-part1, /dev/disk/by-id/scsi-SATA_ST3320620A_9QF3GBGS-part1, /dev/disk/by-path/pci-0000:00:11.1-scsi-0:0:0:0-part1, /dev/disk/by-uuid/f34b9fab-95bf-4ec9-a19b-38c650503d10, /dev/root
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #42 (Disk)

44: None 00.0: 11300 Partition
  [Created at block.412]
  UDI: /org/freedesktop/Hal/devices/volume_part2_size_1024
  Unique ID: 2pkM.SE1wIdpsiiC
  Parent ID: 3OOL.VXhFutAVWLA
  SysFS ID: /class/block/sda/sda2
  Hardware Class: partition
  Model: "Partition"
  Device File: /dev/sda2
  Device Files: /dev/sda2, /dev/block/8:2, /dev/disk/by-id/ata-ST3320620A_9QF3GBGS-part2, /dev/disk/by-id/scsi-SATA_ST3320620A_9QF3GBGS-part2, /dev/disk/by-path/pci-0000:00:11.1-scsi-0:0:0:0-part2
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #42 (Disk)

45: None 00.0: 11300 Partition
  [Created at block.412]
  UDI: /org/freedesktop/Hal/devices/volume_uuid_7201679e_bb67_4300_a0ee_84e9ed9b5762
  Unique ID: QLVZ.SE1wIdpsiiC
  Parent ID: 3OOL.VXhFutAVWLA
  SysFS ID: /class/block/sda/sda5
  Hardware Class: partition
  Model: "Partition"
  Device File: /dev/sda5
  Device Files: /dev/sda5, /dev/block/8:5, /dev/disk/by-id/ata-ST3320620A_9QF3GBGS-part5, /dev/disk/by-id/scsi-SATA_ST3320620A_9QF3GBGS-part5, /dev/disk/by-path/pci-0000:00:11.1-scsi-0:0:0:0-part5, /dev/disk/by-uuid/7201679e-bb67-4300-a0ee-84e9ed9b5762
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #42 (Disk)

46: SCSI 100.0: 10602 CD-ROM (DVD)
  [Created at block.247]
  UDI: /org/freedesktop/Hal/devices/storage_model_DVD_RW_AD_7201A
  Unique ID: KD9E.VD94obDzjr8
  Parent ID: +Y+h.mcsZ0a690T4
  SysFS ID: /class/block/sr0
  SysFS BusID: 1:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:11.1/host1/target1:0:0/1:0:0:0
  Hardware Class: cdrom
  Model: "Optiarc DVD RW AD-7201A"
  Vendor: "Optiarc"
  Device: "DVD RW AD-7201A"
  Revision: "1.09"
  Driver: "pata_via", "sr"
  Driver Modules: "pata_via"
  Device File: /dev/sr0 (/dev/sg1)
  Device Files: /dev/sr0, /dev/block/11:0, /dev/scd0, /dev/disk/by-path/pci-0000:00:11.1-scsi-1:0:0:0, /dev/cdrom, /dev/cdrw, /dev/dvd, /dev/dvdrw
  Device Number: block 11:0 (char 21:1)
  Features: CD-R, CD-RW, DVD, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD+DL, DVDRAM
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #23 (IDE interface)
  Drive Speed: 48

47: SCSI 200.0: 10600 Disk
  [Created at block.254]
  UDI: /org/freedesktop/Hal/devices/storage_serial_WD_CR_HS_CF_0501155021B5_0_0
  Unique ID: vlBd.coZPgSLKWXF
  Parent ID: f5xu.D4EZuGTknpB
  SysFS ID: /class/block/sdb
  SysFS BusID: 2:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:10.3/usb2/2-3/2-3.4/2-3.4:1.0/host2/target2:0:0/2:0:0:0
  Hardware Class: disk
  Model: "WD CR    HS-CF"
  Vendor: usb 0x1058 "WD"
  Device: usb 0x0600 "CR    HS-CF"
  Revision: "3.04"
  Serial ID: "0501155021B5"
  Driver: "usb-storage", "sd"
  Driver Modules: "usb_storage"
  Device File: /dev/sdb (/dev/sg2)
  Device Files: /dev/sdb, /dev/block/8:16, /dev/disk/by-id/usb-WD_CR_HS-CF_0501155021B5-0:0, /dev/disk/by-path/pci-0000:00:10.3-usb-0:3.4:1.0-scsi-0:0:0:0
  Device Number: block 8:16-8:31 (char 21:2)
  Features: Hotpluggable
  Speed: 480 Mbps
  Module Alias: "usb:v1058p0600d0304dc00dsc00dp00ic08isc06ip50"
  Driver Info #0:
    Driver Status: usb_storage is active
    Driver Activation Cmd: "modprobe usb_storage"
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #21 (USB Controller)

48: SCSI 200.1: 10600 Disk
  [Created at block.254]
  UDI: /org/freedesktop/Hal/devices/storage_serial_WD_CR_HS_5_IN_1_0501155021B5_0_1
  Unique ID: LUEV.pSAOJuY_vY4
  Parent ID: f5xu.D4EZuGTknpB
  SysFS ID: /class/block/sdc
  SysFS BusID: 2:0:0:1
  SysFS Device Link: /devices/pci0000:00/0000:00:10.3/usb2/2-3/2-3.4/2-3.4:1.0/host2/target2:0:0/2:0:0:1
  Hardware Class: disk
  Model: "WD CR    HS-5-IN-1"
  Vendor: usb 0x1058 "WD"
  Device: usb 0x0600 "CR    HS-5-IN-1"
  Revision: "3.04"
  Driver: "usb-storage", "sd"
  Driver Modules: "usb_storage"
  Device File: /dev/sdc (/dev/sg3)
  Device Files: /dev/sdc, /dev/block/8:32, /dev/disk/by-id/usb-WD_CR_HS-5-IN-1_0501155021B5-0:1, /dev/disk/by-path/pci-0000:00:10.3-usb-0:3.4:1.0-scsi-0:0:0:1
  Device Number: block 8:32-8:47 (char 21:3)
  Features: Hotpluggable
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #21 (USB Controller)

49: SCSI 300.0: 10600 Disk
  [Created at block.254]
  UDI: /org/freedesktop/Hal/devices/storage_serial_HTC_Android_Phone_HT97EKF01333_0_0
  Unique ID: cLrx.jW1DX79qdF9
  Parent ID: PDCj.GHR7+o5Uy50
  SysFS ID: /class/block/sdd
  SysFS BusID: 3:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:0b.2/usb1/1-2/1-2:1.0/host3/target3:0:0/3:0:0:0
  Hardware Class: disk
  Model: "HTC Android Phone"
  Vendor: usb 0x0bb4 "HTC"
  Device: usb 0x0c01 "Android Phone"
  Revision: "0100"
  Serial ID: "HT97EKF01333"
  Driver: "usb-storage", "sd"
  Driver Modules: "usb_storage"
  Device File: /dev/sdd (/dev/sg4)
  Device Files: /dev/sdd, /dev/block/8:48, /dev/disk/by-id/usb-HTC_Android_Phone_HT97EKF01333-0:0, /dev/disk/by-path/pci-0000:00:0b.2-usb-0:2:1.0-scsi-0:0:0:0
  Device Number: block 8:48-8:63 (char 21:4)
  Features: Hotpluggable
  Speed: 480 Mbps
  Module Alias: "usb:v0BB4p0C01d0100dc00dsc00dp00ic08isc06ip50"
  Driver Info #0:
    Driver Status: usb_storage is active
    Driver Activation Cmd: "modprobe usb_storage"
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #17 (USB Controller)

50: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_0b_2_if0
  Unique ID: k4bc.vhIxNKDPNa3
  Parent ID: PDCj.GHR7+o5Uy50
  SysFS ID: /devices/pci0000:00/0000:00:0b.2/usb1/1-0:1.0
  SysFS BusID: 1-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic ehci_hcd EHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic ehci_hcd"
  Device: usb 0x0002 "EHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:0b.2"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 480 Mbps
  Module Alias: "usb:v1D6Bp0002d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #17 (USB Controller)

51: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_10_3_if0
  Unique ID: pBe4.HJH4vdOnhl8
  Parent ID: f5xu.D4EZuGTknpB
  SysFS ID: /devices/pci0000:00/0000:00:10.3/usb2/2-0:1.0
  SysFS BusID: 2-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic ehci_hcd EHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic ehci_hcd"
  Device: usb 0x0002 "EHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:10.3"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 480 Mbps
  Module Alias: "usb:v1D6Bp0002d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #21 (USB Controller)

52: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_0b_0_if0
  Unique ID: uIhY.Uu0aCsrHYoB
  Parent ID: gZD2.ZszXABOwfd6
  SysFS ID: /devices/pci0000:00/0000:00:0b.0/usb3/3-0:1.0
  SysFS BusID: 3-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:0b.0"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #15 (USB Controller)

53: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_0b_1_if0
  Unique ID: zPk0.Fd59ace+U43
  Parent ID: Xuit.ZszXABOwfd6
  SysFS ID: /devices/pci0000:00/0000:00:0b.1/usb4/4-0:1.0
  SysFS BusID: 4-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:0b.1"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #16 (USB Controller)

54: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_10_0_if0
  Unique ID: 2XnU.5nw7MPEyvh9
  Parent ID: 37TO.1U83dZBAcO6
  SysFS ID: /devices/pci0000:00/0000:00:10.0/usb5/5-0:1.0
  SysFS BusID: 5-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:10.0"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #18 (USB Controller)

55: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_10_1_if0
  Unique ID: 7eqy.sV+ij91gsz0
  Parent ID: wRyD.1U83dZBAcO6
  SysFS ID: /devices/pci0000:00/0000:00:10.1/usb6/6-0:1.0
  SysFS BusID: 6-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:10.1"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #19 (USB Controller)

56: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_10_2_if0
  Unique ID: BSFT.dE4I5wpNpF8
  Parent ID: nmR3.1U83dZBAcO6
  SysFS ID: /devices/pci0000:00/0000:00:10.2/usb7/7-0:1.0
  SysFS BusID: 7-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.32-24-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.32-24-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:10.2"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #20 (USB Controller)

57: USB 00.0: 10a00 Hub
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_1058_500_noserial_if0
  Unique ID: 7bWa.E0sn_j5T_oE
  Parent ID: pBe4.HJH4vdOnhl8
  SysFS ID: /devices/pci0000:00/0000:00:10.3/usb2/2-3/2-3:1.0
  SysFS BusID: 2-3:1.0
  Hardware Class: hub
  Model: "Western Digital Hub"
  Hotplug: USB
  Vendor: usb 0x1058 "Western Digital Technologies, Inc."
  Device: usb 0x0500
  Revision: "0.07"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 480 Mbps
  Module Alias: "usb:v1058p0500d0007dc09dsc00dp02ic09isc00ip02"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #51 (Hub)

58: USB 00.0: 11500 Bluetooth Device
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_a12_1_noserial_if0
  Unique ID: KRJj.nQKjiuCfL84
  Parent ID: uIhY.Uu0aCsrHYoB
  SysFS ID: /devices/pci0000:00/0000:00:0b.0/usb3/3-1/3-1:1.0
  SysFS BusID: 3-1:1.0
  Hardware Class: bluetooth
  Model: "Cambridge Silicon Radio Bluetooth Dongle (HCI mode)"
  Hotplug: USB
  Vendor: usb 0x0a12 "Cambridge Silicon Radio, Ltd"
  Device: usb 0x0001 "Bluetooth Dongle (HCI mode)"
  Revision: "8.28"
  Driver: "btusb"
  Driver Modules: "btusb"
  Speed: 12 Mbps
  Module Alias: "usb:v0A12p0001d0828dcE0dsc01dp01icE0isc01ip01"
  Driver Info #0:
    Driver Status: btusb is active
    Driver Activation Cmd: "modprobe btusb"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #52 (Hub)

63: ADB 00.0: 10502 Bus Mouse
  [Created at input.183]
  UDI: /org/freedesktop/Hal/devices/computer_logicaldev_input_2
  Unique ID: kZYT.VdKNesd9pT6
  Hardware Class: mouse
  Model: "Macintosh mouse button emulation"
  Vendor: 0x0001
  Device: 0x0001 "Macintosh mouse button emulation"
  Compatible to: int 0x0210 0x0003
  Device File: /dev/input/mice (/dev/input/mouse0)
  Device Files: /dev/input/mice, /dev/input/mouse0, /dev/input/event3, /dev/char/13:67, /dev/char/13:32, /dev/char/13:63
  Device Number: char 13:63 (char 13:32)
  Driver Info #0:
    Buttons: 3
    Wheels: 0
    XFree86 Protocol: explorerps/2
    GPM Protocol: exps2
  Config Status: cfg=new, avail=yes, need=no, active=unknown

64: PS/2 00.0: 10800 Keyboard
  [Created at input.161]
  UDI: /org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input
  Unique ID: c3zD.+49ps10DtUF
  Hardware Class: keyboard
  Model: "AT Translated Set 2 keyboard"
  Vendor: 0x0001
  Device: 0x0001 "AT Translated Set 2 keyboard"
  Compatible to: int 0x0211 0x0001
  Device File: /dev/input/event4
  Device Files: /dev/input/event4, /dev/char/13:68, /dev/input/by-path/platform-i8042-serio-0-event-kbd
  Device Number: char 13:68
  Driver Info #0:
    XkbRules: xfree86
    XkbModel: pc104
  Config Status: cfg=new, avail=yes, need=no, active=unknown

65: PS/2 00.0: 10500 PS/2 Mouse
  [Created at input.183]
  UDI: /org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input
  Unique ID: AH6Q.bGO0sOimOM3
  Hardware Class: mouse
  Model: "ImExPS/2 Generic Explorer Mouse"
  Vendor: 0x0002
  Device: 0x0006 "ImExPS/2 Generic Explorer Mouse"
  Compatible to: int 0x0210 0x0025
  Device File: /dev/input/mice (/dev/input/mouse1)
  Device Files: /dev/input/mice, /dev/input/mouse1, /dev/input/event5, /dev/char/13:69, /dev/input/by-path/platform-i8042-serio-1-event-mouse, /dev/char/13:33, /dev/input/by-path/platform-i8042-serio-1-mouse, /dev/char/13:63
  Device Number: char 13:63 (char 13:33)
  Driver Info #0:
    Buttons: 5
    Wheels: 2
    XFree86 Protocol: explorerps/2
    GPM Protocol: exps2
  Config Status: cfg=new, avail=yes, need=no, active=unknown

66: None 00.0: 10103 CPU
  [Created at cpu.304]
  Unique ID: rdCR.j8NaKXDZtZ6
  Hardware Class: cpu
  Arch: Intel
  Vendor: "AuthenticAMD"
  Model: 6.10.0 "AMD Athlon(tm) XP 2500+"
  Features: fpu,vme,de,pse,tsc,msr,pae,mce,cx8,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse,syscall,mmxext,3dnowext,3dnow,up
  Clock: 1825 MHz
  BogoMips: 3648.33
  Cache: 512 kb
  Config Status: cfg=new, avail=yes, need=no, active=unknown

67: None 00.0: 10700 Loopback
  [Created at net.124]
  Unique ID: ZsBS.GQNx7L4uPNA
  SysFS ID: /class/net/lo
  Hardware Class: network interface
  Model: "Loopback network interface"
  Device File: lo
  Link detected: yes
  Config Status: cfg=new, avail=yes, need=no, active=unknown

68: None 00.0: 10701 Ethernet
  [Created at net.124]
  Unique ID: usDW.ndpeucax6V1
  Parent ID: rBUF.OR+pqLEx8F6
  SysFS ID: /class/net/eth0
  SysFS Device Link: /devices/pci0000:00/0000:00:12.0
  Hardware Class: network interface
  Model: "Ethernet network interface"
  Driver: "via-rhine"
  Driver Modules: "via_rhine"
  Device File: eth0
  HW Address: 00:0d:87:7f:d4:6a
  Link detected: yes
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #25 (Ethernet controller)

69: None 00.0: 10701 Ethernet
  [Created at net.124]
  Unique ID: sG1U.ndpeucax6V1
  SysFS ID: /class/net/vboxnet0
  Hardware Class: network interface
  Model: "Ethernet network interface"
  Device File: vboxnet0
  HW Address: 0a:00:27:00:00:00
  Config Status: cfg=new, avail=yes, need=no, active=unknown

70: None 00.0: 10701 Ethernet
  [Created at net.124]
  Unique ID: fLK9.ndpeucax6V1
  SysFS ID: /class/net/pan0
  Hardware Class: network interface
  Model: "Ethernet network interface"
  Driver: "bridge"
  Device File: pan0
  HW Address: 6a:6a:d9:e6:ea:91
  Config Status: cfg=new, avail=yes, need=no, active=unknown

[Rover623]

Problém bude hlavně ta grafika a ovladače pro ní.Ati staré karty vyřadila z oficiálních ovladačů a ty svobodné jsou trochu problém (hlavně slabý výkon karty).Jinak zkus zmáčknout CTRL+ALT+F1 a po naskočení terminálu se přihlas,možná ti systém vypíše nějakou chybu,tedy spíš to co máš zadat aby jsi se dověděl co je v BIOSu blbě nastaveno (párkrát už jsem s tím našel chybu v nastavení BIOSu počítače),zpět do grafického rozhraní se dostaneš pomocí CTRL+ALT+F7

[ondrejkovic]

Hm, tak to žádnou chybu nehlásí. Myslíte, že by pomohlo vyhodit tu grafiku? Mám někde ve skříni starou nVidii 32MB RAM - sice starý střep, ale mohlo by to fungovat lépe než ta prehistoriská ATI. Můžu to jen tak vyhodit a vyměnit? Naskočí mi to potom vůbec?

[Rover623]

Ano.můžeš to jen tak přehodit,ale koukni se co to za nVidii vůbec je,starý ovladač,označený jako verze 76 nefunguje s novým xserverem,takže pokud by ti to nabídlo instalaci uzavřeného ovladače ve verzi 76,tak neinstalovat,asi už by jsi nerozběhl Xserver,ale v tom případě budeš odkázán na ovladače novau (nebo jak se to píše) a ty nejsou zrovna nic moc