Compiz nefunguje správně

[Tomáš Karger]

Ahoj, nainstaloval jsem na svůj 64-bit Ubuntu 6.06 Dapper drake xgl a následně Compiz. Postupoval jsem podle tohoto návodu: https://help.ubuntu.com/community/CompositeManager/InstallingCompiz
Vše je, zdá se, nainstalováno správně (i ovladače od grafické karty jsem kontroloval), ale když spustím Compiz příkazem

Kód: [Vybrat]

compiz –replace gconf, tak zmizí horní i dolní systémová lišta, orámování kolem všech oken a nejde je zavřít, přepínat mezi nimi, ani s nimi pohnout. Je zajímavé, že uvnitř okna fungují zcela normálně. Zkoušel jsem to napravit pomocí příkazu

Kód: [Vybrat]

gtk-window-decorator, ale to nepomohlo.
Nemáte někdo potuchy co je špatně?
Předem díky za pomoc.

[uf]

compiz spustam s tymto scriptom:

#!/bin/bash
gnome-window-decorator &  compiz --replace gconf &

a prostredie XGL mam nastavene iba v /etc/gdm/gdm.conf-custom

# GDM Configuration Customization file.
#
# This file is the appropriate place for specifying your customizations to the
# GDM configuration.   If you run gdmsetup, it will automatically edit this
# file for you and will cause the daemon and any running GDM GUI programs to
# automatically update with the new configuration.  Not all configuration
# options are supported by gdmsetup, so to modify some values it may be
# necessary to modify this file directly by hand.
#
# Older versions of GDM used the "gdm.conf" file for configuration.  If your
# system has an old gdm.conf file on the system, it will be used instead of
# this file - so changes made to this file will not take effect.  Consider
# migrating your configuration to this file and removing the gdm.conf file.
#
# To hand-edit this file, simply add or modify the key=value combination in
# the appropriate section in the template below.  Refer to the comments in the
# /usr/share/gdm/defaults.conf file for information about each option.  Also
# refer to the reference documentation.
#
# If you hand edit a GDM configuration file, you should run the following
# command to get the GDM daemon to notice the change.  Any running GDM GUI
# programs will also be notified to update with the new configuration.
#
# gdmflexiserver --command="UPDATE_CONFIG "
#
# e.g, the "Enable" key in the "[debug]" section would be "debug/Enable".
#
# You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and
# re-read the new configuration settings.  You can also restart GDM by sending
# a HUP or USR1 signal to the daemon.  HUP behaves like gdm-restart and causes
# any user session started by GDM to exit immediately while USR1 behaves like
# gdm-safe-restart and will wait until all users log out before restarting GDM.
#
# For full reference documentation see the gnome help browser under
# GNOME|System category.  You can also find the docs in HTML form on
# http://www.gnome.org/projects/gdm/
#
# NOTE: Lines that begin with "#" are considered comments.
#
# Have fun!

[daemon]
TimedLoginDelay=10
TimedLogin=hc
AutomaticLogin=hc
TimedLoginEnable=true

[security]

[xdmcp]

[gui]

[greeter]
GraphicalTheme=light_in_darkness
SoundOnLogin=false
GraphicalThemedColor=#050000

[chooser]

[debug]

[servers]
0=Xgl                 <<<------------------- XGL nastavenie je od tohto riadku az po koniec!

[server-Xgl]
name=Xgl server
command=/usr/bin/Xgl :0 -fullscreen -ac -accel glx:pbuffer -accel xv:fbo
flexible=true

v Sedeni mam nastavene aby sa po mojom prihalseni spustil hore uvedeny script....takto fungujem bez problemov

[Tomáš Karger]

Pořád nic. Nastavení xgl v Gdm.conf-custom jsem udělal stejně jako vy. Je pravda, že už se čas od času zobrazí systémové lišty, ale hlavní problém s okny zůstává...