Prosíme přihlašte se nebo zaregistrujte.

Přihlašte se svým uživatelským jménem a heslem.
Vaše pomoc je stále potřeba!

Autor Téma: Advanced Power Management - HDD parametre (hdparam)  (Přečteno 1996 krát)

dorinand

  • Návštěvník
  • Příspěvků: 7
Advanced Power Management - HDD parametre (hdparam)
« kdy: 25 Října 2016, 11:54:59 »
Ahoj,
mám pripojený externý disk k raspberry PI a chcel by som nastaviť aby sa pri nečinnosti automaticky prestal točiť. Nastavujem to pomocou hdparam. Parametrom "-S" nastavujem, za ako dlho sa má disk prestať točiť (spinning down). Nerozumiem ale čo znamená APM ("-B"). Čo zmením hodnotou APM? Viem, že ak je APM menšie ako 128 tak je možné nastaviť spinning down(APM =254 je reserved a APM=255 disable). Aký je ale rozidel medzi APM=20 a APM = 120? Vie mi to niekto vysvetliť ?

Z výstupu hdparam -I vidím, že je APM=254. Hodnotu spinning down tam nevidím, je možné že to môj disk nepodporuje? Pri zadaní hdparam -S 60 /dev/sdx nevyskočí žiadna chyba, vyzerá to, že príkaz prebehne v poriadku:

$ sudo hdparm -S 60 /dev/sda
 setting standby to 60 (5 minutes)

HDD mám ADATA HD710. Pripájam aj výstup z hdparam -I:

ATA device, with non-removable media
        Model Number:       ST1000LM024 HN-M101MBB                 
        Serial Number:      S2S6J9DC812917     
        Firmware Revision:  2AR10001
        Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
        Used: unknown (minor revision code 0x0028)
        Supported: 8 7 6 5
        Likely used: 8
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors: 1953525168
        Logical  Sector size:                   512 bytes
        Physical Sector size:                  4096 bytes
        Logical Sector-0 offset:                  0 bytes
        device size with M = 1024*1024:      953869 MBytes
        device size with M = 1000*1000:     1000204 MBytes (1000 GB)
        cache/buffer size  = 8192 KBytes
        Form Factor: 2.5 inch
        Nominal Media Rotation Rate: 5400
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 32
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = ?
        Advanced power management level: 254
        Recommended acoustic management value: 254, current value: 0
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    SMART feature set
                Security Mode feature set
           *    Power Management feature set
           *    Write cache
           *    Look-ahead
           *    Host Protected Area feature set
           *    WRITE_BUFFER command
           *    READ_BUFFER command
           *    NOP cmd
           *    DOWNLOAD_MICROCODE
           *    Advanced Power Management feature set
                Power-Up In Standby feature set
           *    SET_FEATURES required to spinup after power up
                SET_MAX security extension
                Automatic Acoustic Management feature set
           *    48-bit Address feature set
           *    Device Configuration Overlay feature set
           *    Mandatory FLUSH_CACHE
           *    FLUSH_CACHE_EXT
           *    SMART error logging
           *    SMART self-test
           *    General Purpose Logging feature set
           *    64-bit World wide name
           *    IDLE_IMMEDIATE with UNLOAD
           *    WRITE_UNCORRECTABLE_EXT command
           *    {READ,WRITE}_DMA_EXT_GPL commands
           *    Segmented DOWNLOAD_MICROCODE
           *    Gen1 signaling speed (1.5Gb/s)
           *    Gen2 signaling speed (3.0Gb/s)
           *    Native Command Queueing (NCQ)
           *    Phy event counters
           *    Idle-Unload when NCQ is active
           *    NCQ priority information
                DMA Setup Auto-Activate optimization
                Device-initiated interface power management
           *    Software settings preservation
           *    SMART Command Transport (SCT) feature set
           *    SCT Read/Write Long (AC1), obsolete
           *    SCT Write Same (AC2)
           *    SCT Error Recovery Control (AC3)
           *    SCT Features Control (AC4)
           *    SCT Data Tables (AC5)
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
                supported: enhanced erase
        200min for SECURITY ERASE UNIT. 200min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50004cf20841d5b9
        NAA             : 5
        IEEE OUI        : 0004cf
        Unique ID       : 20841d5b9
Checksum: correct


 

Provoz zaštiťuje spolek OpenAlt.