Dalkove ovladani

[spacekkt]

Mam trosku problem s nastavenim lirc. Nemam podle mne spravne moduly do jadra..
Pri zavedeni potrebneho modulu (navod z wiki) pise tohle
spacek@obyvakcomp:~$ modprobe lirc_i2c
WARNING: Error inserting lirc_dev (/lib/modules/2.6.24-16-generic/updates/dkms/lirc_dev.ko): Operation not permitted
FATAL: Error inserting lirc_i2c (/lib/modules/2.6.24-16-generic/updates/dkms/lirc_i2c.ko): Operation not permitted

tak nejak nemam tucha co s tim....Mam pripojenej k seriovemu portu stavenej prevodnik kterej asi dle osciloskopu beha.


Diky za jakekoliv popichnuti spravnym smerem...

[existpierre]

sudo modprobe lirc_i2c

[spacekkt]

Ani jako root to nejde to jsem samozrejme delal jako root jen kdyy jsem psal do fora jsem nebyl jako root...
viz:
root@obyvakcomp:/home/spacek# modprobe lirc_i2c
WARNING: Error inserting lirc_dev (/lib/modules/2.6.24-16-generic/updates/dkms/lirc_dev.ko): Invalid module format
FATAL: Error inserting lirc_i2c (/lib/modules/2.6.24-16-generic/updates/dkms/lirc_i2c.ko): Invalid module format

[Rincewind]

Pokud se nepletu, tak na obyčejný sériový příjmač bys neměl i2c vůbec potřebovat - stačí lirc_serial, v nastavení vybrat správný port, ten odpojit a mohlo by to naběhnout:

Kód: [Vybrat]

/etc/init.d/lirc stop
setserial /dev/ttyS0 uart none (resp. ttyS1,2,3... podle sériového portu)
 /etc/init.d/lirc start

Doplním svůj /etc/sysconfig/lirc pro sériový infrasnímač od karty Technisat (je to z opensuse, na ubuntu je to asi /etc/lirc/hardware.conf)

Kód: [Vybrat]

## Path:           Hardware/Lirc
## Description:    lirc (infrared remote control) configuration
## Type:           string
## Default:        "660"
## ServiceRestart: lirc
#
# permissions for /dev/lircd
#
LIRCD_DEV_PERMISSIONS="660"

## Type:        string
## Default:     "root:video"
#
# owner and group for /dev/lircd
#
LIRCD_DEV_OWNER="root:video"

## Type:        string
## Default:     ""
#
# use given driver
#
LIRCD_DRIVER="default"

# LIRCD_DRIVER="pinsys"

## Type:        string
## Default:     ""
#
# read from given device
#
LIRCD_DEVICE="/dev/lirc"

# LIRCD_DEVICE="/dev/ttyS3"

#LIRCD_DEVICE=/dev/input/event5

## Type:        string(lirc_bt829,lirc_gpio,lirc_i2c,lirc_it87,lirc_parallel,lirc_sir,ir-kbd-i2c,ir-kbd-gpio)
## Default:     ""
#
# load given lirc driver module
#
LIRC_MODULE="lirc_serial"

# LIRC_MODULE=lirc_i2c

## Type:        string
## Default:     ""
#
# listen for network connections on specified port.
# WARNING: don't use this on a machine with an internet
# connection as lircd is running as root!
#
LIRCD_LISTENPORT=""

## Type:        string
## Default:     ""
#
# connect lircd to specified host
#
LIRCD_CONNECT=""
Potom k dálkovému ovladači /etc/lircd.conf (ovladače technisat, potom pinnacle a nakonec jednotlačítkový fisherprice správnou definici ke svému ovladači stáhneš z www.lirc.org:

Kód: [Vybrat]

#
# this config file was automatically generated
# using lirc-0.7.1pre2(any) on Mon Jul 4 22:11:52 2005
#
# contributed by
#
# brand:        Technisat
# model no. of remote control: TTS35AI
# devices being controlled by this remote: Skystar 2.6D
#

begin remote

  name Technisat_TTS35AI.conf
  bits 13
  flags RC5|CONST_LENGTH
  eps 30
  aeps 100

  one 882   803
  zero 882   803
  plead 905
  gap        112766
  toggle_bit   2


      begin codes
  Power    0x1A8C
  Mute    0x1A8D
  1    0x1281
  2    0x1A82
  3    0x1283
  4    0x1A84
  5    0x1285
  6    0x1A86
  7    0x1287
  8    0x1A88
  9    0x1289
  0    0x1A80
  -/--    0x128A
  A/B    0x1AA3
  Red    0x0AAB
  Green    0x02AC
  Yellow    0x0AAD
  Blue    0x02AE
  OK    0x0A97
  Up    0x12A0
  Down    0x1AA1
  Left    0x1291
  Right    0x1A90
  SFI    0x12AF
  Exit    0x1AA2
  INFO    0x028F
#    Prog+     0x1AA0
#    Prog-     0x12A1
  TV/Radio    0x0293
#    Volume+     0x1A90
#    Volume-     0x1291
  Menu    0x0A92
  Hilfe    0x1A8F
  TXT    0x12BC
  STOP    0x1AA9
  EXT    0x12B8
  HILFE2    0x0AB6
      end codes

end remote

begin remote

  name  Pinnacle_RC42D
  bits           13
  flags RC5|CONST_LENGTH
  eps            30
  aeps          100

  one           909   858
  zero          909   858
  plead         937
  gap          113162
  toggle_bit_mask 0x0

      begin codes
          MUTE                     0x19C1
          POWER                    0x11F9
          CTVERECSETREMIRADKY      0x19E5
          TV                       0x11E6
          EPG                      0x19E7
          A_RED                    0x11C3
          B_GREEN                  0x19C4
          C_YELLOW                 0x11C5
          OTAZNIK_BLUE             0x19C6
          VOL_PLUS                 0x11E8
          VOL_MINUS                0x19E9
          PINNACLE                 0x11F3
          CH_PLUS                  0x19C8
          CH_MINUS                 0x11C9
          UP                       0x19CA
          LEFT                     0x11CC
          OK                       0x19F6
          RIGHT                    0x11CD
          DOWN                     0x19CB
          BACK                     0x11F0
          JUMP                     0x19EA
          CTVERECVECTVERCI         0x11C2
          PAUSE                    0x19E1
          RED_IN_THE_MIDDLE        0x11FF
          PREV                     0x19E0
          PLAY                     0x11EB
          FFORWARD                 0x19E2
          BEGINNING                0x11E3
          STOP                     0x19FC
          END                      0x11E4
          1                        0x19CE
          2                        0x11CF
          3                        0x19D1
          4                        0x11D2
          5                        0x11D4
          6                        0x19D5
          7                        0x11D7
          8                        0x19D8
          9                        0x11DA
          CAPS_NUM                 0x19DB
          0                        0x11DD
          DEL                      0x19DE
      end codes

end remote

# Please make this file available to others
# by sending it to <lirc@bartelmus.de>
#
# this config file was automatically generated
# using lirc-0.8.2-CVS(default) on Fri Sep 21 22:56:39 2007
#
# contributed by
#
# brand:                       Fisher Price C0108
# model no. of remote control:
# devices being controlled by this remote:
#

begin remote

  name   fisherprice
  flags RAW_CODES|CONST_LENGTH
  eps            30
  aeps          100

  ptrail        887
  repeat     0     0
  gap    113152

      begin raw_codes

          name nota
              121     839     864     824     864     821
              864     822     891

      end raw_codes

end remote



a nakonec konfigurace lirc pro mythtv .lircrc v domovském adresáři (na který vede symlink z .mythtv)

Kód: [Vybrat]

begin
prog = mythtv
button = 0
repeat = 3
config = 0
end

begin
prog = mythtv
button = 1
repeat = 3
config = 1
end

begin
prog = mythtv
button = 2
repeat = 3
config = 2
end

begin
prog = mythtv
button = 3
repeat = 3
config = 3
end

begin
prog = mythtv
button = 4
repeat = 3
config = 4
end

begin
prog = mythtv
button = 5
repeat = 3
config = 5
end

begin
prog = mythtv
button = 6
repeat = 3
config = 6
end

begin
prog = mythtv
button = 7
repeat = 3
config = 7
end

begin
prog = mythtv
button = 8
repeat = 3
config = 8
end

begin
prog = mythtv
button = 9
repeat = 3
config = 9
end

begin
prog = mythtv
button = UP
repeat = 3
config = Up
end

begin
prog = mythtv
button = DOWN
repeat = 3
config = Down
end

begin
prog = mythtv
button = LEFT
repeat = 3
config = Left
end

begin
prog = mythtv
button = RIGHT
repeat = 3
config = Right
end

begin
prog = mythtv
button = OK
repeat = 3
config = Space
end

begin
prog = mythtv
button = POWER
repeat = 3
config = Esc
end

# pinnacle

begin
prog = mythtv
button = BACK
repeat = 2
config = Esc
end


begin
prog = mythtv
button = Red
repeat = 3
config = Esc
end

begin
prog = mythtv
button = MUTE
repeat = 2
config = |
end

begin
prog = mythtv
button = STOP
repeat = 3
config = p
end

# fisherprice

begin
prog = mythtv
button = nota
repeat = 3
config = p
end


# pinnacle

begin
prog = mythtv
button = PAUSE
repeat = 2
config = p
end


begin
prog = mythtv
button = INFO
repeat = 3
config = I
end

# pinnacle

begin
prog = mythtv
button = CTVERECVECTVERCI
repeat = 2
config = I
end

# technisat

begin
prog = mythtv
button = Menu
repeat = 3
config = M
end

# pinnacle

begin
prog = mythtv
button = PINNACLE
repeat = 2
config = M
end

# technisat

begin
prog = mythtv
button = TV/Radio
repeat = 3
config = Shift+T
end

begin
prog = mythtv
button = Exit
repeat = 3
config = Esc
end

begin
prog = mythtv
button = -/--
repeat = 3
config = PgDown
end

begin
prog = mythtv
button = A/B
repeat = 3
config = PgUp
end

# Pinnacle

begin
prog = mythtv
button = BEGINNING
repeat = 2
config = PgDown
end

begin
prog = mythtv
button = END
repeat = 2
config = PgUp
end

# technisat

begin
prog = mythtv
button = Green
repeat = 3
config = Z
end

begin
prog = mythtv
button = SFI
repeat = 3
config = Shift+G
end

# technisat - hlasitost

begin
prog = mythtv
button = Hilfe
repeat = 2
config = ]
end

begin
prog = mythtv
button = HILFE2
repeat = 2
config = [
end

# pinnacle - hlasitost

begin
prog = mythtv
button = VOL_PLUS
repeat = 2
config = ]
end

begin
prog = mythtv
button = VOL_MINUS
repeat = 2
config = [
end

# pinnacle - to co neni na technisatu

begin
prog = mythtv
button = DEL
repeat = 2
config = D
end

# DALSI PROGRAM
# mplayer

begin
   prog = mplayer
   button = MUTE
   config = mute
end
begin
   prog = mplayer
   button = POWER
   config = quit 166
end
begin
   prog = mplayer
   button = 1
   repeat = 1
   config = volume 1
end
begin
   prog = mplayer
   button = 2
   repeat = 2
   config = dvdnav 1
end
begin
   prog = mplayer
   button = 3
   repeat = 3
   config = seek 60
end
begin
   prog = mplayer
   button = 4
   repeat = 2
   config = dvdnav 3
end
begin
   prog = mplayer
   button = 5
   repeat = 2
   config = dvdnav 6
end
begin
   prog = mplayer
   button = 6
   repeat = 2
   config = dvdnav 4
end
begin
   prog = mplayer
   button = 7
   repeat = 1
   config = volume -1
end
begin
   prog = mplayer
   button = 8
   repeat = 2
   config = dvdnav 2
end
begin
   prog = mplayer
   button = 9
   repeat = 3
   config = seek -60
end
begin
   prog = mplayer
   button = 0
   repeat = 2
   config = dvdnav 5
end
begin
   prog = mplayer
   button = RED
   config = quit 166
end
begin
   prog = mplayer
   button = GREEN
   config = play
end
begin
   prog = mplayer
   button = STOP
   config = pause
end
begin
   prog = mplayer
   button = BLUE
   config = play_dvd hide_menu
end
begin
   prog = mplayer
   button = LEFT
   config = volume -1
end
begin
   prog = mplayer
   button = RIGHT
   config = volume 1
end

begin
prog = mplayer
button = Hilfe
repeat = 2
config = volume 1
end

begin
prog = mplayer
button = HILFE2
repeat = 2
config = volume -1
end

# pinnacle - hlasitost - mplayer

begin
prog = mplayer
button = VOL_PLUS
repeat = 2
config = volume 1
end

begin
prog = mplayer
button = VOL_MINUS
repeat = 2
config = volume -1
end

begin
   prog = mplayer
   button = UP
   repeat = 2
   config = seek 60
end
begin
   prog = mplayer
   button = DOWN
   repeat = 2
   config = seek -60
end

# pinnacle posuv

begin
   prog = mplayer
   button = FFORWARD
   repeat = 2
   config = seek 30
end
begin
   prog = mplayer
   button = PREV
   repeat = 2
   config = seek -30
end

begin
   prog = mplayer
   button = BEGINNING
   repeat = 2
   config = seek -180
end
begin
   prog = mplayer
   button = END
   repeat = 2
   config = seek 180
end

# KONEC pinnacle posuvu

begin
   prog = mplayer
   button = OK
   config = pause
end

begin
   prog = mplayer
   button = INFO
   config = osd
end
begin
   prog = mplayer
   button = MENU
   config = menu toggle
end

# pinnacle menu a info

begin
   prog = mplayer
   button = CTVERECVECTVERCI
   config = osd
end
begin
   prog = mplayer
   button = PINNACLE
   config = menu toggle
end

# KONEC pinnacle menu a info

begin
   prog = mplayer
   button = TXT
   config = sub_visibility
end
# begin
#   prog = mplayer
#   button = HILFE2
#   repeat = 32
#   config = vo_fullscreen
# end

# fisherprice mplayer

begin
   prog = mplayer
   button = nota
   config = pause
end





Doplním, že na ubuntu (7.04) jsem lirc vždy rozchodil podle tohoto návodu: https://help.ubuntu.com/community/InstallLirc/Feisty?highlight=(lirc) i když občas to nebylo napoprvé teď je tam už verze i pro 8.04, tak třeba to zafunguje...

[spacekkt]

Mohl bych poprosit jeste o vypis z hardware.conf ? porad si nejsem jit vsemi nastavenimy..... Diky ....

[vadimo]

Možno ti pomôžu moje: Poznámky z rozchodenia Lirc

[Rincewind]

Mohl bych poprosit jeste o vypis z hardware.conf ? porad si nejsem jit vsemi nastavenimy..... Diky ....

Měl by to být ten první soubor - na suse se všechno jmenuje jinak, ale jsem si téměř jist, že /etc/sysconfig/lirc = hardware.conf kdekoli jinde