tak zase zkouším od večera do rána a nedaří se vše se nahraje ale jak vložím tohle dmesg vyleze z terminálu viz níže, mě to připadá jako když tu kameru ubuntu nerozezná že je připojená. mám ji připojenou přes usb rozbočovač už nemám místo mám na usb klávesnici, myš, usb 500gb disk, tiskárnu a ten rozbočovač tiskárnu a usb kameru mám v tom rozbočovači tak jestli to není tím.
.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Fri Jul 11 23:41:49 UTC 2008 (Ubuntu 2.6.24-19.36-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000dc000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
[ 0.000000] BIOS-e820: 000000007fff0000 - 000000007fff8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fff8000 - 0000000080000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fc020
[ 0.000000] Entering add_active_range(0, 0, 524272) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 524272
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 524272
[ 0.000000] On node 0 totalpages: 524272
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2303 pages used for memmap
[ 0.000000] HighMem zone: 292593 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FA6D0 checksum 0
[ 0.000000] ACPI: RSDP 000FA6D0, 0014 (r0 AMI )
[ 0.000000] ACPI: RSDT 7FFF0000, 002C (r1 AMIINT VIA_P6 10 MSFT 97)
[ 0.000000] ACPI: FACP 7FFF0030, 0081 (r1 AMIINT VIA_P6 11 MSFT 97)
[ 0.000000] ACPI: DSDT 7FFF0120, 3502 (r1 VIA APOLLO-P 1000 MSFT 100000D)
[ 0.000000] ACPI: FACS 7FFF8000, 0040
[ 0.000000] ACPI: APIC 7FFF00C0, 005C (r1 AMIINT VIA_P6 9 MSFT 97)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:3 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:3 APIC version 20
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000dc000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000dc000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520177
[ 0.000000] Kernel command line: root=UUID=1f04275d-2ef3-483f-b91f-8101adc7e8e4 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 3013.810 MHz processor.
[ 41.693422] Console: colour VGA+ 80x25
[ 41.693428] console [tty0] enabled
[ 41.694630] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 41.695744] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 41.877530] Memory: 2066552k/2097088k available (2177k kernel code, 29216k reserved, 1006k data, 368k init, 1179584k highmem)
[ 41.877546] virtual kernel memory layout:
[ 41.877547] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 41.877549] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 41.877551] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 41.877552] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 41.877554] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 41.877555] .data : 0xc0320474 - 0xc041bdc4 (1006 kB)
[ 41.877557] .text : 0xc0100000 - 0xc0320474 (2177 kB)
[ 41.877561] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 41.877644] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 41.957500] Calibrating delay using timer specific routine.. 6147.33 BogoMIPS (lpj=12294660)
[ 41.957550] Security Framework initialized
[ 41.957563] SELinux: Disabled at boot.
[ 41.957591] AppArmor: AppArmor initialized
[ 41.957598] Failure registering capabilities with primary security module.
[ 41.957611] Mount-cache hash table entries: 512
[ 41.957829] Initializing cgroup subsys ns
[ 41.957837] Initializing cgroup subsys cpuacct
[ 41.957857] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 00000000
[ 41.957870] monitor/mwait feature present.
[ 41.957872] using mwait in idle threads.
[ 41.957882] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 41.957885] CPU: L2 cache: 1024K
[ 41.957890] CPU: Physical Processor ID: 0
[ 41.957893] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b180 0000441d 00000000 00000000 00000000
[ 41.957910] Compat vDSO mapped to ffffe000.
[ 41.957937] Checking 'hlt' instruction... OK.
[ 41.974056] SMP alternatives: switching to UP code
[ 41.976665] Early unpacking initramfs... done
[ 42.418247] ACPI: Core revision 20070126
[ 42.418756] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 42.422057] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
[ 42.422082] SMP alternatives: switching to SMP code
[ 42.423001] Booting processor 1/1 eip 3000
[ 42.433333] Initializing CPU#1
[ 42.512217] Calibrating delay using timer specific routine.. 6027.53 BogoMIPS (lpj=12055076)
[ 42.512228] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 00000000
[ 42.512235] monitor/mwait feature present.
[ 42.512242] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 42.512245] CPU: L2 cache: 1024K
[ 42.512247] CPU: Physical Processor ID: 0
[ 42.512250] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b180 0000441d 00000000 00000000 00000000
[ 42.512631] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
[ 42.512677] Total of 2 processors activated (12174.86 BogoMIPS).
[ 42.513424] ENABLING IO-APIC IRQs
[ 42.513746] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 42.660265] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 42.680235] Brought up 2 CPUs
[ 42.680298] CPU0 attaching sched-domain:
[ 42.680302] domain 0: span 03
[ 42.680304] groups: 01 02
[ 42.680308] domain 1: span 03
[ 42.680310] groups: 03
[ 42.680312] CPU1 attaching sched-domain:
[ 42.680314] domain 0: span 03
[ 42.680316] groups: 02 01
[ 42.680319] domain 1: span 03
[ 42.680321] groups: 03
[ 42.680594] net_namespace: 64 bytes
[ 42.680602] Booting paravirtualized kernel on bare hardware
[ 42.681187] Time: 5:29:05 Date: 07/21/08
[ 42.681216] NET: Registered protocol family 16
[ 42.681496] EISA bus registered
[ 42.681503] ACPI: bus type pci registered
[ 42.683167] PCI: PCI BIOS revision 2.10 entry at 0xfdb11, last bus=1
[ 42.683169] PCI: Using configuration type 1
[ 42.683175] Setting up standard PCI resources
[ 42.697565] ACPI: EC: Look up EC in DSDT
[ 42.701489] ACPI: Interpreter enabled
[ 42.701492] ACPI: (supports S0 S1 S4 S5)
[ 42.701509] ACPI: Using IOAPIC for interrupt routing
[ 42.706407] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 42.708432] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 42.711580] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 42.711684] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 42.711783] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 42.711883] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 42.711982] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 42.712082] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 42.712186] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 42.712293] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 42.712414] ACPI: Power Resource [URP1] (off)
[ 42.712446] ACPI: Power Resource [URP2] (off)
[ 42.712479] ACPI: Power Resource [FDDP] (off)
[ 42.712509] ACPI: Power Resource [LPTP] (off)
[ 42.712574] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 42.712617] pnp: PnP ACPI init
[ 42.712626] ACPI: bus type pnp registered
[ 42.715176] pnp: PnP ACPI: found 10 devices
[ 42.715179] ACPI: ACPI bus type pnp unregistered
[ 42.715184] PnPBIOS: Disabled by ACPI PNP
[ 42.715507] PCI: Using ACPI for IRQ routing
[ 42.715511] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 42.736244] NET: Registered protocol family 8
[ 42.736247] NET: Registered protocol family 20
[ 42.736342] AppArmor: AppArmor Filesystem Enabled
[ 42.740136] Time: tsc clocksource has been installed.
[ 42.752289] system 00:01: ioport range 0x290-0x297 has been reserved
[ 42.752292] system 00:01: ioport range 0x3f0-0x3f1 has been reserved
[ 42.752295] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 42.752298] system 00:01: ioport range 0x400-0x40f has been reserved
[ 42.752300] system 00:01: ioport range 0x820-0x821 has been reserved
[ 42.752304] system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 42.782813] PCI: Bridge: 0000:00:01.0
[ 42.782816] IO window: disabled.
[ 42.782821] MEM window: f3e00000-f7efffff
[ 42.782825] PREFETCH window: d3d00000-f3cfffff
[ 42.782846] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 42.782859] NET: Registered protocol family 2
[ 42.820333] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 42.820765] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 42.821777] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 42.822852] TCP: Hash tables configured (established 131072 bind 65536)
[ 42.822856] TCP reno registered
[ 42.832515] checking if image is initramfs... it is
[ 43.440285] Switched to high resolution mode on CPU 0
[ 43.440290] Switched to high resolution mode on CPU 1
[ 43.622505] Freeing initrd memory: 7832k freed
[ 43.623645] audit: initializing netlink socket (disabled)
[ 43.623670] audit(1216618145.628:1): initialized
[ 43.623965] highmem bounce pool size: 64 pages
[ 43.626895] VFS: Disk quotas dquot_6.5.1
[ 43.627003] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 43.627191] io scheduler noop registered
[ 43.627194] io scheduler anticipatory registered
[ 43.627196] io scheduler deadline registered
[ 43.627208] io scheduler cfq registered (default)
[ 43.627226] PCI: VIA PCI bridge detected. Disabling DAC.
[ 43.627301] PCI: Bypassing VIA 8237 APIC De-Assert Message
[ 43.627325] Boot video device is 0000:01:00.0
[ 43.627702] isapnp: Scanning for PnP cards...
[ 43.978574] isapnp: No Plug & Play device found
[ 44.017219] Real Time Clock Driver v1.12ac
[ 44.017353] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 44.017487] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 44.018426] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 44.019456] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 44.019539] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 44.019674] PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12
[ 44.019677] PNP: PS/2 controller doesn't have KBD irq; using default 1
[ 44.020077] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 44.020086] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 44.033491] mice: PS/2 mouse device common for all mice
[ 44.033663] EISA: Probing bus 0 at eisa.0
[ 44.033706] EISA: Detected 0 cards.
[ 44.033710] cpuidle: using governor ladder
[ 44.033712] cpuidle: using governor menu
[ 44.033813] NET: Registered protocol family 1
[ 44.033845] Using IPI No-Shortcut mode
[ 44.033884] registered taskstats version 1
[ 44.033978] Magic number: 0:39:467
[ 44.034133] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 44.034135] EDD information not available.
[ 44.034637] Freeing unused kernel memory: 368k freed
[ 45.290975] fuse init (API version 7.9)
[ 45.818351] SCSI subsystem initialized
[ 45.908941] usbcore: registered new interface driver usbfs
[ 45.908979] usbcore: registered new interface driver hub
[ 45.909033] libata version 3.00 loaded.
[ 45.933662] usbcore: registered new device driver usb
[ 45.945830] pata_via 0000:00:0f.0: version 0.3.3
[ 45.945881] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 45.949048] scsi0 : pata_via
[ 45.954208] USB Universal Host Controller Interface driver v3.0
[ 45.955098] scsi1 : pata_via
[ 45.958118] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 45.958124] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 45.959613] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 46.029900] Floppy drive(s): fd0 is 1.44M
[ 46.052851] FDC 0 is a post-1991 82077
[ 46.297496] ata1.00: ATA-6: ST380011A, 8.01, max UDMA/100
[ 46.297504] ata1.00: 156301488 sectors, multi 16: LBA48
[ 46.297712] ata1.01: ATA-6: WDC WD800JB-00FMA0, 13.03G13, max UDMA/100
[ 46.297717] ata1.01: 156301488 sectors, multi 16: LBA
[ 46.313353] ata1.00: configured for UDMA/100
[ 46.329298] ata1.01: configured for UDMA/100
[ 46.647415] ata2.00: ATAPI: _NEC DVD_RW ND-3500AG, 2.1B, max UDMA/33
[ 46.819878] ata2.00: configured for UDMA/33
[ 46.820046] scsi 0:0:0:0: Direct-Access ATA ST380011A 8.01 PQ: 0 ANSI: 5
[ 46.820224] scsi 0:0:1:0: Direct-Access ATA WDC WD800JB-00FM 13.0 PQ: 0 ANSI: 5
[ 46.821201] scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-3500AG 2.1B PQ: 0 ANSI: 5
[ 46.821651] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
[ 46.821669] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 46.822020] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 46.822057] uhci_hcd 0000:00:10.0: irq 17, io base 0x0000dc00
[ 46.822261] usb usb1: configuration #1 chosen from 1 choice
[ 46.822302] hub 1-0:1.0: USB hub found
[ 46.822311] hub 1-0:1.0: 2 ports detected
[ 46.923581] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
[ 46.923600] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 46.923641] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 46.923671] uhci_hcd 0000:00:10.1: irq 17, io base 0x0000e000
[ 46.923843] usb usb2: configuration #1 chosen from 1 choice
[ 46.923898] hub 2-0:1.0: USB hub found
[ 46.923909] hub 2-0:1.0: 2 ports detected
[ 47.027295] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17
[ 47.027313] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 47.027352] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 47.027378] uhci_hcd 0000:00:10.2: irq 17, io base 0x0000e400
[ 47.027558] usb usb3: configuration #1 chosen from 1 choice
[ 47.027600] hub 3-0:1.0: USB hub found
[ 47.027609] hub 3-0:1.0: 2 ports detected
[ 47.131061] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 17
[ 47.131079] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 47.131120] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 47.131145] uhci_hcd 0000:00:10.3: irq 17, io base 0x0000e800
[ 47.131322] usb usb4: configuration #1 chosen from 1 choice
[ 47.131361] hub 4-0:1.0: USB hub found
[ 47.131370] hub 4-0:1.0: 2 ports detected
[ 47.235499] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 18
[ 47.235956] eth0: VIA Rhine II at 0xf7fffd00, 00:0c:76:e9:bf:c0, IRQ 18.
[ 47.236666] eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
[ 47.236906] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
[ 47.236926] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 47.236983] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 47.237049] ehci_hcd 0000:00:10.4: irq 17, io mem 0xf7fffe00
[ 47.245679] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 47.245887] usb usb5: configuration #1 chosen from 1 choice
[ 47.245928] hub 5-0:1.0: USB hub found
[ 47.245938] hub 5-0:1.0: 8 ports detected
[ 47.365400] Driver 'sd' needs updating - please use bus_type methods
[ 47.365550] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 47.365578] sd 0:0:0:0: [sda] Write Protect is off
[ 47.365583] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 47.365617] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 47.365718] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 47.365747] sd 0:0:0:0: [sda] Write Protect is off
[ 47.365754] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 47.365796] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 47.365804] sda: sda1
[ 47.370953] sd 0:0:0:0: [sda] Attached SCSI disk
[ 47.371050] sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 47.371071] sd 0:0:1:0: [sdb] Write Protect is off
[ 47.371076] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 47.371108] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 47.371180] sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 47.371198] sd 0:0:1:0: [sdb] Write Protect is off
[ 47.371202] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 47.371232] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 47.371238] sdb:<4>Driver 'sr' needs updating - please use bus_type methods
[ 47.387161] sdb1 sdb2 < sdb5 >
[ 47.412363] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 47.420543] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 47.420552] Uniform CD-ROM driver Revision: 3.20
[ 47.420643] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 47.421897] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 47.421938] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 47.421976] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 47.793488] Attempting manual resume
[ 47.793492] swsusp: Resume From Partition 8:21
[ 47.793494] PM: Checking swsusp image.
[ 47.793703] PM: Resume from disk failed.
[ 47.845040] kjournald starting. Commit interval 5 seconds
[ 47.845055] EXT3-fs: mounted filesystem with ordered data mode.
[ 48.248335] usb 5-3: new high speed USB device using ehci_hcd and address 2
[ 48.380019] usb 5-3: configuration #1 chosen from 1 choice
[ 48.618483] usb 5-4: new high speed USB device using ehci_hcd and address 3
[ 48.754556] usb 5-4: configuration #1 chosen from 1 choice
[ 48.754712] hub 5-4:1.0: USB hub found
[ 48.754810] hub 5-4:1.0: 4 ports detected
[ 48.857950] hub 5-0:1.0: over-current change on port 5
[ 48.965658] hub 5-0:1.0: over-current change on port 6
[ 49.065423] hub 5-0:1.0: over-current change on port 7
[ 49.169182] hub 5-0:1.0: over-current change on port 8
[ 49.472594] usb 5-4.1: new high speed USB device using ehci_hcd and address 4
[ 49.567879] usb 5-4.1: configuration #1 chosen from 1 choice
[ 49.767932] usb 5-4.2: new low speed USB device using ehci_hcd and address 5
[ 49.873533] usb 5-4.2: configuration #1 chosen from 1 choice
[ 55.857741] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 55.915529] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 55.986545] Linux agpgart interface v0.102
[ 56.178096] agpgart: Detected VIA PT880 chipset
[ 56.181828] agpgart: AGP aperture is 64M @ 0xf8000000
[ 56.341925] input: Power Button (FF) as /devices/virtual/input/input1
[ 56.361475] ACPI: Power Button (FF) [PWRF]
[ 56.361653] input: Power Button (CM) as /devices/virtual/input/input2
[ 56.393389] ACPI: Power Button (CM) [PWRB]
[ 56.561230] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 57.435163] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 57.504996] parport_pc 00:09: reported by Plug and Play ACPI
[ 57.505104] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 57.968640] nvidia: module license 'NVIDIA' taints kernel.
[ 58.480035] usbcore: registered new interface driver libusual
[ 58.508600] Initializing USB Mass Storage driver...
[ 58.531964] scsi2 : SCSI emulation for USB Mass Storage devices
[ 58.570902] usb-storage: device found at 2
[ 58.570908] usb-storage: waiting for device to settle before scanning
[ 58.570947] usbcore: registered new interface driver usb-storage
[ 58.570954] USB Mass Storage support registered.
[ 58.577661] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
[ 58.578038] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
[ 58.709190] usbcore: registered new interface driver hiddev
[ 58.715264] input: Chicony Skype Calculator Keyboard as /devices/pci0000:00/0000:00:10.4/usb5/5-4/5-4.2/5-4.2:1.0/input/input5
[ 58.754105] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 20
[ 58.760083] input,hidraw0: USB HID v1.11 Keyboard [Chicony Skype Calculator Keyboard] on usb-0000:00:10.4-4.2
[ 58.767915] input: Chicony Skype Calculator Keyboard as /devices/pci0000:00/0000:00:10.4/usb5/5-4/5-4.2/5-4.2:1.1/input/input6
[ 58.814918] input,hiddev96,hidraw1: USB HID v1.11 Device [Chicony Skype Calculator Keyboard] on usb-0000:00:10.4-4.2
[ 58.814943] usbcore: registered new interface driver usbhid
[ 58.814948] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 60.573362] lp0: using parport0 (interrupt-driven).
[ 60.643506] Adding 3229024k swap on /dev/sdb5. Priority:-1 extents:1 across:3229024k
[ 61.209429] EXT3 FS on sdb1, internal journal
[ 62.435230] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 62.854375] No dock devices found.
[ 63.562238] usb-storage: device scan complete
[ 63.562718] scsi 2:0:0:0: Direct-Access Maxtor OneTouch 0125 PQ: 0 ANSI: 4
[ 63.567952] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 63.568558] sd 2:0:0:0: [sdc] Write Protect is off
[ 63.568563] sd 2:0:0:0: [sdc] Mode Sense: 2d 08 00 00
[ 63.568566] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 63.569679] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 63.570302] sd 2:0:0:0: [sdc] Write Protect is off
[ 63.570306] sd 2:0:0:0: [sdc] Mode Sense: 2d 08 00 00
[ 63.570309] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 63.570315] sdc: sdc2 < sdc5 sdc6 sdc7 sdc8 >
[ 63.631405] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 63.631479] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 64.194883] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 64.194893] apm: disabled - APM is not SMP safe.
[ 64.337392] ppdev: user-space parallel port driver
[ 64.498292] audit(1216610967.032:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4973 profile="/usr/sbin/cupsd" namespace="default"
[ 66.610579] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 66.682594] Bluetooth: Core ver 2.11
[ 66.682960] NET: Registered protocol family 31
[ 66.682965] Bluetooth: HCI device and connection manager initialized
[ 66.682970] Bluetooth: HCI socket layer initialized
[ 66.715076] Bluetooth: L2CAP ver 2.9
[ 66.715085] Bluetooth: L2CAP socket layer initialized
[ 66.796698] Bluetooth: RFCOMM socket layer initialized
[ 66.796955] Bluetooth: RFCOMM TTY layer initialized
[ 66.796961] Bluetooth: RFCOMM ver 1.8
[ 69.222635] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 69.222659] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 69.222725] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 70.219666] NET: Registered protocol family 17
[ 74.015186] NET: Registered protocol family 10
[ 74.016142] lo: Disabled Privacy Extensions
[ 84.558894] eth0: no IPv6 routers present
[ 926.089590] microdia: Unknown symbol video_ioctl2
[ 926.089975] microdia: Unknown symbol video_devdata
[ 926.090393] microdia: Unknown symbol video_unregister_device
[ 926.090556] microdia: Unknown symbol video_device_alloc
[ 926.090637] microdia: Unknown symbol video_register_device
[ 926.090897] microdia: Unknown symbol video_device_release
[ 1273.338585] microdia: Unknown symbol video_ioctl2
[ 1273.338979] microdia: Unknown symbol video_devdata
[ 1273.339395] microdia: Unknown symbol video_unregister_device
[ 1273.339558] microdia: Unknown symbol video_device_alloc
[ 1273.339639] microdia: Unknown symbol video_register_device
[ 1273.339898] microdia: Unknown symbol video_device_release
[ 1313.960213] microdia: Unknown symbol video_ioctl2
[ 1313.960600] microdia: Unknown symbol video_devdata
[ 1313.961008] microdia: Unknown symbol video_unregister_device
[ 1313.961172] microdia: Unknown symbol video_device_alloc
[ 1313.961255] microdia: Unknown symbol video_register_device
[ 1313.961512] microdia: Unknown symbol video_device_release
root@jirka-desktop:/home/jirka/microdia#
Téma: Skype (Přečteno 8275 krát)
