Zdravím Vás. Mám menší problém s USB hubom. Mám k nemu pripojený extrerný disk, čítačku kariet a pripájam k nemu aj telefón. Bohužiaľ zápis je veľmi pomalý. Nepoznáte niekto nejaké riešenie ako to zrýchliť? Keď zariadenie pripojím priamo k notebooku ide všetko ako má.
lsusb Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 04f2:b070 Chicony Electronics Co., Ltd
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 010: ID 0421:04fa Nokia Mobile Phones
Bus 005 Device 009: ID 0930:0b09 Toshiba Corp.
Bus 005 Device 008: ID 04a9:26b4 Canon, Inc. MF4010 Series
Bus 005 Device 007: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 005 Device 003: ID 1307:0330 Transcend Information, Inc.
Bus 005 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 13ee:0003
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
dmesg [ 9.475403] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
[ 9.555707] uvcvideo: Found UVC 1.00 device CNF7051 (04f2:b070)
[ 9.571396] input: CNF7051 as /class/input/input7
[ 9.571396] usbcore: registered new interface driver uvcvideo
[ 9.571396] USB Video Class driver (v0.1.0)
[ 9.735210] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 9.735210] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 9.763945] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 9.807591] usb 7-2: reset high speed USB device using ehci_hcd and address 3
[ 9.898266] rtl8187: 8187B chip detected. Support is EXPERIMENTAL, and could damage your
[ 9.898266] hardware, use at your own risk
[ 9.898266] phy0: Selected rate control algorithm 'pid'
[ 10.080971] phy0: hwaddr 00:16:44:bb:33:ba, RTL8187BvE V0 + rtl8225z2
[ 10.080971] usbcore: registered new interface driver rtl8187
[ 10.080971] phy1: Selected rate control algorithm 'pid'
[ 10.080971] zd1211rw 7-2:1.0: phy1
[ 10.080971] usbcore: registered new interface driver zd1211rw
[ 10.094183] udev: renamed network interface wlan1 to wlan0
[ 10.142043] udev: renamed network interface wlan0_rename to wlan1
[ 10.529101] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x9280b1, caps: 0xa04711/0xa04000
[ 10.529101] synaptics: Toshiba Satellite L300 detected, limiting rate to 40pps.
[ 10.610696] input: SynPS/2 Synaptics TouchPad as /class/input/input8
[ 11.024540] Adding 4104596k swap on /dev/sda3. Priority:-1 extents:1 across:4104596k
[ 11.498087] EXT3 FS on sda1, internal journal
[ 11.734977] loop: module loaded
[ 12.911426] kjournald starting. Commit interval 5 seconds
[ 12.911795] EXT3 FS on sda2, internal journal
[ 12.911795] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.934461] kjournald starting. Commit interval 5 seconds
[ 12.934889] EXT3 FS on sda4, internal journal
[ 12.934889] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.246555] NET: Registered protocol family 10
[ 14.247146] lo: Disabled Privacy Extensions
[ 14.489200] firmware: requesting zd1211/zd1211b_ub
[ 14.536909] usb 7-2: Could not load firmware file zd1211/zd1211b_ub. Error number -2
[ 14.536998] zd1211rw 7-2:1.0: couldn't load firmware. Error number -2
[ 14.537272] firmware: requesting zd1211/zd1211b_ub
[ 14.543383] usb 7-2: Could not load firmware file zd1211/zd1211b_ub. Error number -2
[ 14.543471] zd1211rw 7-2:1.0: couldn't load firmware. Error number -2
[ 26.397120] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 27.893726] lp: driver loaded but no devices found
[ 27.913382] ppdev: user-space parallel port driver
[ 29.076081] RPC: Registered udp transport module.
[ 29.076081] RPC: Registered tcp transport module.
[ 29.146526] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 29.200886] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 29.200975] NFSD: starting 90-second grace period
[ 31.473308] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 31.561079] firmware: requesting zd1211/zd1211b_ub
[ 31.566943] usb 7-2: Could not load firmware file zd1211/zd1211b_ub. Error number -2
[ 31.566943] zd1211rw 7-2:1.0: couldn't load firmware. Error number -2
[ 31.739442] r8169: eth0: link up
[ 31.739442] r8169: eth0: link up
[ 31.919947] r8169: eth0: link up
[ 31.927500] firmware: requesting zd1211/zd1211b_ub
[ 31.933058] usb 7-2: Could not load firmware file zd1211/zd1211b_ub. Error number -2
[ 31.933058] zd1211rw 7-2:1.0: couldn't load firmware. Error number -2
[ 32.701516] Bluetooth: Core ver 2.11
[ 32.701516] NET: Registered protocol family 31
[ 32.701516] Bluetooth: HCI device and connection manager initialized
[ 32.701516] Bluetooth: HCI socket layer initialized
[ 32.737820] Bluetooth: L2CAP ver 2.9
[ 32.737820] Bluetooth: L2CAP socket layer initialized
[ 32.789059] Bluetooth: RFCOMM socket layer initialized
[ 32.789059] Bluetooth: RFCOMM TTY layer initialized
[ 32.789059] Bluetooth: RFCOMM ver 1.8
[ 36.492693] [drm] Initialized drm 1.1.0 20060810
[ 36.494412] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 36.494412] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 36.494412] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 38.541393] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 42.711148] eth0: no IPv6 routers present
[ 51.099473] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 56.135843] CPU0 attaching NULL sched-domain.
[ 56.135857] CPU1 attaching NULL sched-domain.
[ 56.148790] CPU0 attaching sched-domain:
[ 56.148797] domain 0: span 0-1
[ 56.148799] groups: 0 1
[ 56.148804] CPU1 attaching sched-domain:
[ 56.148806] domain 0: span 0-1
[ 56.148808] groups: 1 0
[ 63.259595] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 66.427790] firmware: requesting zd1211/zd1211b_ub
[ 66.436554] usb 7-2: Could not load firmware file zd1211/zd1211b_ub. Error number -2
[ 66.436554] zd1211rw 7-2:1.0: couldn't load firmware. Error number -2
[ 75.384981] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 106.960125] ld[4101]: segfault at 0 ip 40171cac sp bfe0a6ac error 4 in libc-2.7.so[400fa000+155000]
[ 186.494724] ld[11756]: segfault at 0 ip 40171cac sp bfbe639c error 4 in libc-2.7.so[400fa000+155000]
[ 195.756388] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 195.901313] usb 5-1: not running at top speed; connect to a high speed hub
[ 195.921283] usb 5-1: configuration #1 chosen from 1 choice
[ 195.924465] hub 5-1:1.0: USB hub found
[ 195.926399] hub 5-1:1.0: 4 ports detected
[ 196.043816] usb 5-1: New USB device found, idVendor=05e3, idProduct=0608
[ 196.043822] usb 5-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 196.043825] usb 5-1: Product: USB2.0 Hub
[ 196.252919] usb 5-1.1: new full speed USB device using uhci_hcd and address 3
[ 196.354841] usb 5-1.1: not running at top speed; connect to a high speed hub
[ 196.560765] usb 5-1.1: configuration #1 chosen from 1 choice
[ 196.562281] usb 5-1.1: New USB device found, idVendor=1307, idProduct=0330
[ 196.562281] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 196.562281] usb 5-1.1: Product: Mass Storage Device
[ 196.562281] usb 5-1.1: Manufacturer: Generic
[ 196.562281] usb 5-1.1: SerialNumber: 00000000000006
[ 196.682354] Initializing USB Mass Storage driver...
[ 196.780623] usb 5-1.2: new full speed USB device using uhci_hcd and address 4
[ 196.885567] usb 5-1.2: not running at top speed; connect to a high speed hub
[ 196.911403] usb 5-1.2: configuration #1 chosen from 1 choice
[ 196.913834] hub 5-1.2:1.0: USB hub found
[ 196.915766] hub 5-1.2:1.0: 4 ports detected
[ 197.025947] usb 5-1.2: New USB device found, idVendor=05e3, idProduct=0608
[ 197.025953] usb 5-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 197.025956] usb 5-1.2: Product: USB2.0 Hub
[ 197.029796] scsi2 : SCSI emulation for USB Mass Storage devices
[ 197.030491] usb-storage: device found at 3
[ 197.030491] usb-storage: waiting for device to settle before scanning
[ 197.234401] usb 5-1.2.2: new full speed USB device using uhci_hcd and address 5
[ 197.344004] usb 5-1.2.2: not running at top speed; connect to a high speed hub
[ 197.385190] usb 5-1.2.2: configuration #1 chosen from 1 choice
[ 197.392076] usb 5-1.2.2: New USB device found, idVendor=04a9, idProduct=26b4
[ 197.392076] usb 5-1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 197.392076] usb 5-1.2.2: Product: MF4010
[ 197.392076] usb 5-1.2.2: Manufacturer: Canon Inc.
[ 197.392076] usb 5-1.2.2: SerialNumber: SDF820163619Q
[ 197.430254] usbcore: registered new interface driver usb-storage
[ 197.430254] USB Mass Storage support registered.
[ 197.661376] usblp0: USB Bidirectional printer dev 5 if 1 alt 0 proto 2 vid 0x04A9 pid 0x26B4
[ 197.661403] usbcore: registered new interface driver usblp
[ 197.734363] usblp0: nonzero read bulk status received: -84
[ 197.895257] ld[12139]: segfault at 0 ip 40171cac sp bf97412c error 4 in libc-2.7.so[400fa000+155000]
[ 199.353982] ld[12326]: segfault at 0 ip 40171cac sp bfeeb69c error 4 in libc-2.7.so[400fa000+155000]
[ 200.390615] ld[12507]: segfault at 0 ip 40171cac sp bfc333ec error 4 in libc-2.7.so[400fa000+155000]
[ 201.932040] ld[12690]: segfault at 0 ip 40171cac sp bfa8223c error 4 in libc-2.7.so[400fa000+155000]
[ 202.073058] usb-storage: device scan complete
[ 202.075589] scsi 2:0:0:0: Direct-Access Generic USB CF Reader 0.00 PQ: 0 ANSI: 2
[ 202.078282] scsi 2:0:0:1: Direct-Access Generic USB SD Reader 0.00 PQ: 0 ANSI: 2
[ 202.083557] scsi 2:0:0:2: Direct-Access Generic Mini SD Reader 0.00 PQ: 0 ANSI: 2
[ 202.087537] scsi 2:0:0:3: Direct-Access Generic USB MS Reader 0.00 PQ: 0 ANSI: 2
[ 202.090278] scsi 2:0:0:4: Direct-Access Generic USB SM Reader 0.00 PQ: 0 ANSI: 2
[ 202.096518] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 202.100502] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[ 202.105084] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[ 202.111253] sd 2:0:0:3: [sde] Attached SCSI removable disk
[ 202.117088] sd 2:0:0:4: [sdf] Attached SCSI removable disk
[ 212.618586] ld[13028]: segfault at 0 ip 40171cac sp bfe345ec error 4 in libc-2.7.so[400fa000+155000]
[ 268.824589] firmware: requesting zd1211/zd1211b_ub
[ 268.834313] firmware: requesting zd1211/zd1211b_uphr
[ 268.889997] zd1211rw 7-2:1.0: firmware version 4725
[ 268.927748] zd1211rw 7-2:1.0: zd1211b chip 0586:3410 v4810 high 00-19-cb AL2230_RF pa0 g--NS
[ 268.949575] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 269.850844] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 269.858480] wlan0: authenticated
[ 269.858487] wlan0: associate with AP 00:1c:df:7e:df:bd
[ 269.860734] wlan0: RX AssocResp from 00:1c:df:7e:df:bd (capab=0x1 status=0 aid=2)
[ 269.860734] wlan0: associated
[ 269.860734] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 280.367248] wlan0: no IPv6 routers present
[ 302.194810] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 350.947548] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 351.008411] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 351.011980] wlan0: authenticated
[ 351.011980] wlan0: associate with AP 00:1c:df:7e:df:bd
[ 351.044654] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 351.045717] wlan0: authenticated
[ 351.045717] wlan0: associate with AP 00:1c:df:7e:df:bd
[ 351.049555] wlan0: RX AssocResp from 00:1c:df:7e:df:bd (capab=0x1 status=0 aid=2)
[ 351.049555] wlan0: associated
[ 351.049555] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 361.878857] wlan0: no IPv6 routers present
[ 457.736459] usb 5-1.2.4: new full speed USB device using uhci_hcd and address 6
[ 457.848299] usb 5-1.2.4: not running at top speed; connect to a high speed hub
[ 457.888985] usb 5-1.2.4: configuration #1 chosen from 1 choice
[ 457.896120] scsi3 : SCSI emulation for USB Mass Storage devices
[ 457.896204] usb-storage: device found at 6
[ 457.896207] usb-storage: waiting for device to settle before scanning
[ 457.899390] usb 5-1.2.4: New USB device found, idVendor=0930, idProduct=0b09
[ 457.899390] usb 5-1.2.4: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 457.899390] usb 5-1.2.4: Product: USB 3.5"-HDD
[ 457.899390] usb 5-1.2.4: Manufacturer: TOSHIBA
[ 457.899390] usb 5-1.2.4: SerialNumber: 0002Aec0
[ 462.930041] usb-storage: device scan complete
[ 462.938363] scsi 3:0:0:0: Direct-Access TOSHIBA USB 3.5"-HDD 100 PQ: 0 ANSI: 2
[ 462.942438] sd 3:0:0:0: [sdg] 1953525168 512-byte hardware sectors (1000205 MB)
[ 462.947448] sd 3:0:0:0: [sdg] Write Protect is off
[ 462.947453] sd 3:0:0:0: [sdg] Mode Sense: 38 00 00 00
[ 462.947456] sd 3:0:0:0: [sdg] Assuming drive cache: write through
[ 462.954409] sd 3:0:0:0: [sdg] 1953525168 512-byte hardware sectors (1000205 MB)
[ 462.958830] sd 3:0:0:0: [sdg] Write Protect is off
[ 462.958830] sd 3:0:0:0: [sdg] Mode Sense: 38 00 00 00
[ 462.958830] sd 3:0:0:0: [sdg] Assuming drive cache: write through
[ 462.958830] sdg: sdg1
[ 462.970829] sd 3:0:0:0: [sdg] Attached SCSI disk
[ 465.421215] kjournald starting. Commit interval 5 seconds
[ 465.423386] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 465.427428] EXT3 FS on sdg1, internal journal
[ 465.427428] EXT3-fs: recovery complete.
[ 465.435822] EXT3-fs: mounted filesystem with ordered data mode.
[ 512.552917] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 512.553342] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 536.817867] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 548.974903] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 560.482499] ld[21375]: segfault at 0 ip 40171cac sp bfa651cc error 4 in libc-2.7.so[400fa000+155000]
[ 561.312880] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 573.459262] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 581.941212] ld[21644]: segfault at 0 ip 40171cac sp bfa901fc error 4 in libc-2.7.so[400fa000+155000]
[ 586.038327] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 623.884468] ld[21970]: segfault at 0 ip 40171cac sp bf86a7fc error 4 in libc-2.7.so[400fa000+155000]
[ 1258.962981] r8169: eth0: link down
[ 1259.173128] sd 3:0:0:0: [sdg] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 1259.173128] end_request: I/O error, dev sdg, sector 230193175
[ 1259.173128] sd 3:0:0:0: [sdg] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 1259.173128] end_request: I/O error, dev sdg, sector 230193415
[ 1259.175104] usb 5-1.2.4: USB disconnect, address 6
[ 1259.177147] Buffer I/O error on device sdg1, logical block 4100
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Aborting journal on device sdg1.
[ 1259.177147] Buffer I/O error on device sdg1, logical block 1289
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] journal commit I/O error
[ 1259.177147] Buffer I/O error on device sdg1, logical block 11337730
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 13631490
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 14516226
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 15171586
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 18382850
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 19922946
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 21594114
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.177147] Buffer I/O error on device sdg1, logical block 21659650
[ 1259.177147] lost page write due to I/O error on sdg1
[ 1259.369134] ext3_abort called.
[ 1259.369134] EXT3-fs error (device sdg1): ext3_journal_start_sb: Detected aborted journal
[ 1259.369134] Remounting filesystem read-only
[ 1259.623890] CPU0 attaching NULL sched-domain.
[ 1259.623903] CPU1 attaching NULL sched-domain.
[ 1259.651411] CPU0 attaching sched-domain:
[ 1259.651421] domain 0: span 0-1
[ 1259.651424] groups: 0 1
[ 1259.651429] domain 1: span 0-1
[ 1259.651432] groups: 0-1
[ 1259.651438] CPU1 attaching sched-domain:
[ 1259.651441] domain 0: span 0-1
[ 1259.651444] groups: 1 0
[ 1259.651448] domain 1: span 0-1
[ 1259.651451] groups: 0-1
[ 1259.672360] ------------[ cut here ]------------
[ 1259.672360] WARNING: at fs/buffer.c:1186 mark_buffer_dirty+0x20/0x6a()
[ 1259.672360] Modules linked in: usblp usb_storage i915 drm binfmt_misc rfcomm l2cap bluetooth nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs ppdev parport_pc lp parport acpi_cpufreq cpufreq_stats cpufreq_powersave cpufreq_conservative cpufreq_ondemand cpufreq_userspace freq_table ipv6 loop joydev arc4 ecb crypto_blkcipher snd_hda_intel zd1211rw snd_pcm psmouse rtl8187 firmware_class uvcvideo snd_seq i2c_i801 mac80211 eeprom_93cx6 snd_timer snd_seq_device serio_raw i2c_core compat_ioctl32 snd cfg80211 pcspkr videodev soundcore v4l1_compat iTCO_wdt snd_page_alloc video output button battery ac intel_agp agpgart evdev ext3 jbd mbcache dm_mirror dm_log dm_snapshot dm_mod sd_mod ide_cd_mod cdrom usbhid hid ff_memless ata_generic ata_piix libata scsi_mod dock piix ide_pci_generic ide_core r8169 ehci_hcd uhci_hcd usbcore thermal processor fan thermal_sys
[ 1259.672360] Pid: 8199, comm: rhythmbox-metad Not tainted 2.6.26-1-686 #1
[ 1259.672360] [<c012256f>] warn_on_slowpath+0x40/0x66
[ 1259.672360] [<c015a8f1>] __pagevec_free+0x14/0x1a
[ 1259.672360] [<c013604c>] getnstimeofday+0x37/0xbc
[ 1259.672360] [<c01344c2>] ktime_get_ts+0x22/0x49
[ 1259.672360] [<c0133d8e>] enqueue_hrtimer+0xc9/0xd4
[ 1259.672360] [<c0134356>] hrtimer_start+0xf7/0x110
[ 1259.672360] [<c011d3d2>] hrtick_set+0x8f/0xd8
[ 1259.672360] [<c02b8190>] schedule+0x64e/0x66f
[ 1259.672360] [<c019034f>] mark_buffer_dirty+0x20/0x6a
[ 1259.672360] [<f8957c2c>] journal_update_superblock+0x59/0x97 [jbd]
[ 1259.672385] [<f8958753>] journal_destroy+0x11e/0x163 [jbd]
[ 1259.672397] [<c01318dc>] autoremove_wake_function+0x0/0x2d
[ 1259.672409] [<f898ef25>] ext3_put_super+0x1f/0x16c [ext3]
[ 1259.672430] [<c0175d2d>] generic_shutdown_super+0x4f/0xc8
[ 1259.672437] [<c019ee8b>] vfs_quota_off+0x0/0x518
[ 1259.672443] [<c0175db2>] kill_block_super+0xc/0x1b
[ 1259.672449] [<c0175e51>] deactivate_super+0x4b/0x60
[ 1259.672455] [<c0172b81>] filp_close+0x4d/0x53
[ 1259.672462] [<c0173cbb>] sys_close+0x5b/0x8d
[ 1259.672467] [<c0103853>] sysenter_past_esp+0x78/0xb1
[ 1259.672484] =======================
[ 1259.672487] ---[ end trace a56c85167e998fd2 ]---
[ 1260.700787] hub 5-1:1.0: port 2 disabled by hub (EMI?), re-enabling...
[ 1260.701939] usb 5-1.2: USB disconnect, address 4
[ 1260.701939] usb 5-1.2.2: USB disconnect, address 5
[ 1260.701939] usblp0: removed
[ 1260.777081] usb 5-1.2: new full speed USB device using uhci_hcd and address 7
[ 1260.883684] usb 5-1.2: not running at top speed; connect to a high speed hub
[ 1260.903684] usb 5-1.2: configuration #1 chosen from 1 choice
[ 1260.907857] hub 5-1.2:1.0: USB hub found
[ 1260.911775] hub 5-1.2:1.0: 4 ports detected
[ 1261.020839] usb 5-1.2: New USB device found, idVendor=05e3, idProduct=0608
[ 1261.020847] usb 5-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1261.020851] usb 5-1.2: Product: USB2.0 Hub
[ 1263.191585] wlan0: No ProbeResp from current AP 00:1c:df:7e:df:bd - assume out of range
[ 1266.711201] __ratelimit: 20 messages suppressed
[ 1266.711208] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1275.778961] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1276.866052] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 1277.068199] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 1277.267120] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 1277.471241] wlan0: authentication with AP 00:1c:df:7e:df:bd timed out
[ 1278.461298] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1290.242564] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1459.447000] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1459.493443] CPU0 attaching NULL sched-domain.
[ 1459.493454] CPU1 attaching NULL sched-domain.
[ 1459.499015] CPU0 attaching sched-domain:
[ 1459.499015] domain 0: span 0-1
[ 1459.499015] groups: 0 1
[ 1459.499015] CPU1 attaching sched-domain:
[ 1459.499015] domain 0: span 0-1
[ 1459.499015] groups: 1 0
[ 1461.317869] r8169: eth0: link up
[ 1461.840508] usb 5-1.2.2: new full speed USB device using uhci_hcd and address 8
[ 1461.945493] usb 5-1.2.2: not running at top speed; connect to a high speed hub
[ 1461.968196] usb 5-1.2.2: configuration #1 chosen from 1 choice
[ 1461.976190] usblp0: USB Bidirectional printer dev 8 if 1 alt 0 proto 2 vid 0x04A9 pid 0x26B4
[ 1461.976278] usb 5-1.2.2: New USB device found, idVendor=04a9, idProduct=26b4
[ 1461.976285] usb 5-1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1461.976288] usb 5-1.2.2: Product: MF4010
[ 1461.976290] usb 5-1.2.2: Manufacturer: Canon Inc.
[ 1461.976292] usb 5-1.2.2: SerialNumber: SDF820163619Q
[ 1462.134564] usblp0: nonzero read bulk status received: -84
[ 1463.851086] r8169: eth0: link down
[ 1465.917664] r8169: eth0: link up
[ 1469.914589] usb 5-1.2.4: new full speed USB device using uhci_hcd and address 9
[ 1470.021139] usb 5-1.2.4: not running at top speed; connect to a high speed hub
[ 1470.065655] usb 5-1.2.4: configuration #1 chosen from 1 choice
[ 1470.073180] scsi4 : SCSI emulation for USB Mass Storage devices
[ 1470.073180] usb-storage: device found at 9
[ 1470.073180] usb-storage: waiting for device to settle before scanning
[ 1470.073340] usb 5-1.2.4: New USB device found, idVendor=0930, idProduct=0b09
[ 1470.073340] usb 5-1.2.4: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1470.073340] usb 5-1.2.4: Product: USB 3.5"-HDD
[ 1470.073340] usb 5-1.2.4: Manufacturer: TOSHIBA
[ 1470.073340] usb 5-1.2.4: SerialNumber: 0002Aec0
[ 1473.915971] r8169: eth0: link up
[ 1475.106614] usb-storage: device scan complete
[ 1475.112118] scsi 4:0:0:0: Direct-Access TOSHIBA USB 3.5"-HDD 100 PQ: 0 ANSI: 2
[ 1475.119444] sd 4:0:0:0: [sdg] 1953525168 512-byte hardware sectors (1000205 MB)
[ 1475.125240] sd 4:0:0:0: [sdg] Write Protect is off
[ 1475.125240] sd 4:0:0:0: [sdg] Mode Sense: 38 00 00 00
[ 1475.125240] sd 4:0:0:0: [sdg] Assuming drive cache: write through
[ 1475.130028] sd 4:0:0:0: [sdg] 1953525168 512-byte hardware sectors (1000205 MB)
[ 1475.133027] sd 4:0:0:0: [sdg] Write Protect is off
[ 1475.133027] sd 4:0:0:0: [sdg] Mode Sense: 38 00 00 00
[ 1475.133027] sd 4:0:0:0: [sdg] Assuming drive cache: write through
[ 1475.133027] sdg: sdg1
[ 1475.149466] sd 4:0:0:0: [sdg] Attached SCSI disk
[ 1484.004061] eth0: no IPv6 routers present
[ 1490.146318] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1491.151374] wlan0: authenticate with AP 00:1c:df:7e:df:bd
[ 1491.155140] wlan0: authenticated
[ 1491.155140] wlan0: associate with AP 00:1c:df:7e:df:bd
[ 1491.157534] wlan0: RX AssocResp from 00:1c:df:7e:df:bd (capab=0x401 status=0 aid=1)
[ 1491.157534] wlan0: associated
[ 1491.157534] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1496.475970] kjournald starting. Commit interval 5 seconds
[ 1496.475970] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 1496.481243] EXT3 FS on sdg1, internal journal
[ 1496.481243] EXT3-fs: recovery complete.
[ 1496.487514] EXT3-fs: mounted filesystem with ordered data mode.
[ 1501.325585] wlan0: no IPv6 routers present
[ 1829.906887] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1842.452635] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1854.568352] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1866.873345] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1879.013717] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1891.123377] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1891.123377] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1903.268975] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1903.773088] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 3780.922259] usb 5-1.2.1: new full speed USB device using uhci_hcd and address 10
[ 3781.051012] usb 5-1.2.1: configuration #1 chosen from 1 choice
[ 3781.062337] scsi5 : SCSI emulation for USB Mass Storage devices
[ 3781.062337] usb-storage: device found at 10
[ 3781.062337] usb-storage: waiting for device to settle before scanning
[ 3781.062337] usb 5-1.2.1: New USB device found, idVendor=0421, idProduct=04fa
[ 3781.062337] usb 5-1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3781.062337] usb 5-1.2.1: Product: Nokia 6300
[ 3781.062337] usb 5-1.2.1: Manufacturer: Nokia
[ 3781.062337] usb 5-1.2.1: SerialNumber: 356796020122522
[ 3786.123725] usb-storage: device scan complete
[ 3786.128216] scsi 5:0:0:0: Direct-Access Nokia Nokia 6300 0000 PQ: 0 ANSI: 4
[ 3786.184760] sd 5:0:0:0: [sdh] 3932161 512-byte hardware sectors (2013 MB)
[ 3786.188760] sd 5:0:0:0: [sdh] Write Protect is off
[ 3786.188760] sd 5:0:0:0: [sdh] Mode Sense: 03 00 00 00
[ 3786.188760] sd 5:0:0:0: [sdh] Assuming drive cache: write through
[ 3786.200760] sd 5:0:0:0: [sdh] 3932161 512-byte hardware sectors (2013 MB)
[ 3786.204760] sd 5:0:0:0: [sdh] Write Protect is off
[ 3786.204760] sd 5:0:0:0: [sdh] Mode Sense: 03 00 00 00
[ 3786.204760] sd 5:0:0:0: [sdh] Assuming drive cache: write through
[ 3786.204760] sdh:
[ 3786.268757] sd 5:0:0:0: [sdh] Attached SCSI removable disk
[ 3786.428128] sd 5:0:0:0: [sdh] Sense Key : No Sense [current]
[ 3786.428128] sd 5:0:0:0: [sdh] Add. Sense: No additional sense information
[ 3786.676075] sd 5:0:0:0: [sdh] Sense Key : No Sense [current]
[ 3786.676075] sd 5:0:0:0: [sdh] Add. Sense: No additional sense information
[ 3786.941496] sd 5:0:0:0: [sdh] Sense Key : No Sense [current]
[ 3786.941496] sd 5:0:0:0: [sdh] Add. Sense: No additional sense information
[ 3787.650120] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 3788.920022] sd 5:0:0:0: [sdh] Sense Key : No Sense [current]
[ 3788.920022] sd 5:0:0:0: [sdh] Add. Sense: No additional sense information
Téma: USB-HUB pomalá rýchlosť (Přečteno 2600 krát)
