Prosíme přihlašte se nebo zaregistrujte.

Přihlašte se svým uživatelským jménem a heslem.
Vaše pomoc je stále potřeba!

Autor Téma: Pinnacle PCTV 310i ubuntu 11.10  (Přečteno 1912 krát)

kacerek99

  • Host
Pinnacle PCTV 310i ubuntu 11.10
« kdy: 14 Ledna 2012, 16:36:24 »
Zdravim hledal sem vsude i tento navod jsem nasel http://www.abclinuxu.cz/hardware/pridavne-karty/televizni-karty/dvb-t/pci/pinnacle-pctv-310i ale nerozumim tomu   jsem začatečník... ty příkazy nefungují....i jine navody ale nepochopil jsem pridavam výpisi .

lspci
Citace
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2)
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:07.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62)
01:07.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62)
01:07.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 65)
01:09.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d0)
01:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev 80)
05:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] (rev a2)

lspci -vv
 
Citace
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Capabilities: <access denied>

00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Interrupt: pin A routed to IRQ 5
   Region 0: I/O ports at ff00 [size=32]
   Region 4: I/O ports at 4c00 [size=64]
   Region 5: I/O ports at 4c40 [size=64]
   Capabilities: <access denied>
   Kernel driver in use: nForce2_smbus
   Kernel modules: i2c-nforce2

00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0 (750ns min, 250ns max)
   Interrupt: pin A routed to IRQ 20
   Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
   Capabilities: <access denied>
   Kernel driver in use: ohci_hcd

00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0 (750ns min, 250ns max)
   Interrupt: pin B routed to IRQ 21
   Region 0: Memory at feb00000 (32-bit, non-prefetchable) [size=256]
   Capabilities: <access denied>
   Kernel driver in use: ehci_hcd

00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)
   Subsystem: Micro-Star International Co., Ltd. Device 7585
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0 (500ns min, 1250ns max)
   Interrupt: pin A routed to IRQ 22
   Region 0: I/O ports at ea00 [size=256]
   Region 1: I/O ports at ee00 [size=256]
   Region 2: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
   Capabilities: <access denied>
   Kernel driver in use: Intel ICH
   Kernel modules: snd-intel8x0

00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP])
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0 (750ns min, 250ns max)
   Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
   Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
   Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
   Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
   Region 4: I/O ports at fb00 [size=16]
   Capabilities: <access denied>
   Kernel driver in use: pata_amd
   Kernel modules: pata_amd

00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0 (750ns min, 250ns max)
   Interrupt: pin A routed to IRQ 23
   Region 0: I/O ports at 09f0 [size=8]
   Region 1: I/O ports at 0bf0
   Region 2: I/O ports at 0970 [size=8]
   Region 3: I/O ports at 0b70
   Region 4: I/O ports at f600 [size=16]
   Region 5: Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
   Capabilities: <access denied>
   Kernel driver in use: sata_nv
   Kernel modules: sata_nv

00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0 (750ns min, 250ns max)
   Interrupt: pin A routed to IRQ 22
   Region 0: I/O ports at 09e0 [size=8]
   Region 1: I/O ports at 0be0
   Region 2: I/O ports at 0960 [size=8]
   Region 3: I/O ports at 0b60
   Region 4: I/O ports at f100 [size=16]
   Region 5: Memory at febfa000 (32-bit, non-prefetchable) [size=4K]
   Capabilities: <access denied>
   Kernel driver in use: sata_nv
   Kernel modules: sata_nv

00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
   I/O behind bridge: 0000d000-0000dfff
   Memory behind bridge: fe900000-fe9fffff
   Prefetchable memory behind bridge: fea00000-feafffff
   Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
   BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-

00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
   Subsystem: Micro-Star International Co., Ltd. Device 7125
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
   Latency: 0 (250ns min, 5000ns max)
   Interrupt: pin A routed to IRQ 23
   Region 0: Memory at febf9000 (32-bit, non-prefetchable) [size=4K]
   Region 1: I/O ports at f000 [size=8]
   Capabilities: <access denied>
   Kernel driver in use: forcedeth
   Kernel modules: forcedeth

00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 32 bytes
   Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
   I/O behind bridge: 0000c000-0000cfff
   Memory behind bridge: fe800000-fe8fffff
   Prefetchable memory behind bridge: 00000000fe700000-00000000fe7fffff
   Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
   BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 32 bytes
   Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
   I/O behind bridge: 0000b000-0000bfff
   Memory behind bridge: fe600000-fe6fffff
   Prefetchable memory behind bridge: 00000000fe500000-00000000fe5fffff
   Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
   BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 32 bytes
   Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
   I/O behind bridge: 0000a000-0000afff
   Memory behind bridge: fe400000-fe4fffff
   Prefetchable memory behind bridge: 00000000fe300000-00000000fe3fffff
   Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
   BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 32 bytes
   Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
   I/O behind bridge: 00009000-00009fff
   Memory behind bridge: f4000000-fbffffff
   Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
   Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
   BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Capabilities: <access denied>

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Kernel driver in use: k8temp
   Kernel modules: k8temp

01:07.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62) (prog-if 00 [UHCI])
   Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32, Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 17
   Region 4: I/O ports at df00 [size=32]
   Capabilities: <access denied>
   Kernel driver in use: uhci_hcd

01:07.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62) (prog-if 00 [UHCI])
   Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32, Cache Line Size: 32 bytes
   Interrupt: pin B routed to IRQ 18
   Region 4: I/O ports at de00 [size=32]
   Capabilities: <access denied>
   Kernel driver in use: uhci_hcd

01:07.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 65) (prog-if 20 [EHCI])
   Subsystem: VIA Technologies, Inc. USB 2.0
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32, Cache Line Size: 32 bytes
   Interrupt: pin C routed to IRQ 19
   Region 0: Memory at fe9ff000 (32-bit, non-prefetchable) [size=256]
   Capabilities: <access denied>
   Kernel driver in use: ehci_hcd

01:09.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d0)
   Subsystem: Pinnacle Systems Inc. Device 002f
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32 (21000ns min, 8000ns max)
   Interrupt: pin A routed to IRQ 19
   Region 0: Memory at fe9fe000 (32-bit, non-prefetchable) [size=2K]
   Capabilities: <access denied>
   Kernel driver in use: saa7134
   Kernel modules: saa7134

01:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev 80) (prog-if 10 [OHCI])
   Subsystem: Device 0574:086c
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32, Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 19
   Region 0: Memory at fe9fd000 (32-bit, non-prefetchable) [size=2K]
   Region 1: I/O ports at dd00 [size=128]
   Capabilities: <access denied>
   Kernel driver in use: firewire_ohci
   Kernel modules: firewire-ohci

05:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] (rev a2) (prog-if 00 [VGA controller])
   Subsystem: LeadTek Research Inc. Device 2a22
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 18
   Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64M]
   Region 1: Memory at d8000000 (64-bit, prefetchable) [size=128M]
   Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=16M]
   [virtual] Expansion ROM at f8000000 [disabled] [size=128K]
   Capabilities: <access denied>
   Kernel driver in use: nvidia
   Kernel modules: nvidia_current_updates, nvidia_173_updates, nvidia_96, nvidia_173, nvidia_current, nouveau, nvidiafb

nevim k čemu ty vipisi sou ale vecina lidi to vypisovala...
děkuji za včechny rady

kacerek99

  • Host
Re:Pinnacle PCTV 310i ubuntu 11.10
« Odpověď #1 kdy: 14 Ledna 2012, 18:21:50 »
díky mopc vypada to ze to pude prosim o ozuvření

 

Provoz zaštiťuje spolek OpenAlt.