Nemůžu zkopírovat žádné DVD, Pokud vytvořím ISO soubor, přes K3b nebo K9copy, ISO se vytvoří, ale pokud tento soubor chci zkopírovat do jiného adresáře, příp. vypálit přes k3b, tak přibližně při 70% PC na cca. 5 s zamrzne a pak vypíše chybu, že soubor nemůže přečíst. Je špatný HDD, nebo v čem může být problém. Mám zapnutý SMART
START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.8 family
Device Model: ST3200826AS
Serial Number: 3ND20KH4
Firmware Version: 3.04
User Capacity: 200 049 647 616 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Dec 12 16:59:50 2007 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 67) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 054 044 006 Pre-fail Always - 116754362
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 988
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8
7 Seek_Error_Rate 0x000f 076 060 030 Pre-fail Always - 46164240
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1074
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 990
194 Temperature_Celsius 0x0022 037 042 000 Old_age Always - 37 (Lifetime Min/Max 0/16)
195 Hardware_ECC_Recovered 0x001a 054 044 000 Old_age Always - 116754362
197 Current_Pending_Sector 0x0012 089 089 000 Old_age Always - 216
198 Offline_Uncorrectable 0x0010 089 089 000 Old_age Offline - 216
199 UDMA_CRC_Error_Count 0x003e 200 199 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 13883 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13883 occurred at disk power-on lifetime: 1074 hours (44 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 b4 d3 af e0 Error: UNC 5 sectors at LBA = 0x00afd3b4 = 11522996
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 af d3 af e0 00 01:16:22.673 READ DMA EXT
27 00 00 00 00 00 e0 00 01:16:22.671 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 01:16:19.112 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:16:19.112 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:16:19.109 READ NATIVE MAX ADDRESS EXT
Error 13882 occurred at disk power-on lifetime: 1074 hours (44 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 b4 d3 af e0 Error: UNC 5 sectors at LBA = 0x00afd3b4 = 11522996
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 af d3 af e0 00 01:16:22.673 READ DMA EXT
27 00 00 00 00 00 e0 00 01:16:22.671 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 01:16:19.112 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:16:19.112 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:16:19.109 READ NATIVE MAX ADDRESS EXT
Error 13881 occurred at disk power-on lifetime: 1074 hours (44 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 b4 d3 af e0 Error: UNC 5 sectors at LBA = 0x00afd3b4 = 11522996
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 af d3 af e0 00 01:16:11.984 READ DMA EXT
27 00 00 00 00 00 e0 00 01:16:11.981 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 01:16:19.112 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:16:19.112 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:16:19.109 READ NATIVE MAX ADDRESS EXT
Error 13880 occurred at disk power-on lifetime: 1074 hours (44 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 b4 d3 af e0 Error: UNC 5 sectors at LBA = 0x00afd3b4 = 11522996
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 af d3 af e0 00 01:16:11.984 READ DMA EXT
27 00 00 00 00 00 e0 00 01:16:11.981 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 01:16:11.981 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:16:11.981 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:16:11.977 READ NATIVE MAX ADDRESS EXT
Error 13879 occurred at disk power-on lifetime: 1074 hours (44 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 b4 d3 af e0 Error: UNC 5 sectors at LBA = 0x00afd3b4 = 11522996
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 af d3 af e0 00 01:16:11.984 READ DMA EXT
27 00 00 00 00 00 e0 00 01:16:11.981 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 01:16:11.981 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:16:11.981 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:16:11.977 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Vyznáte se v tom někdo?