Prosíme přihlašte se nebo zaregistrujte.

Přihlašte se svým uživatelským jménem a heslem.
Vaše pomoc je stále potřeba!

Autor Téma: KOMPLET navod na zdielanie suborov cez SAMBU  (Přečteno 14178 krát)

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
KOMPLET navod na zdielanie suborov cez SAMBU
« kdy: 12 Listopadu 2007, 10:09:09 »
dobre asi som este menej skuseny ale vsade sa len pise co treba nainstalovat a aky subor sa edituje a tam to konci..........mozno by aj ini ocenili keby sa tu niekde nasiel kompletny strucny navod co a ako sa nielen nainstaluje ale aj ako pripoji na iny pocitac ..proste od piky..... aj vy ste niekedy zacinali )
« Poslední změna: 13 Prosince 2007, 20:13:02 od Anna Taliánová »

ufaak

  • Závislák
  • ***
  • Příspěvků: 2296
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #1 kdy: 12 Listopadu 2007, 10:11:27 »
mozna by stacilo hledat...
http://wiki.ubuntu.cz/Samba
notebook MSI EX720X, Ubuntu 10.10

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #2 kdy: 12 Listopadu 2007, 10:14:57 »
ano..ten navod som presiel......ale co robit po nainstalovani a upravovani samba conf. suboru som sa dalej nedostal......myslim ze zakricat na pocitac PRIPOJ SA NA DRUHY KOMP nebude zrejme stacit :-)

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #3 kdy: 12 Listopadu 2007, 10:35:49 »
to vsetko mam z toho navodu wiki ...ked dam Vzdialene miesta tak mi to vypise ze: Nepodarilo sa najst ziadne pracovne skupiny na vasej lokalnej sieti ....   

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #4 kdy: 12 Listopadu 2007, 10:41:06 »
kde to mam prosim hladat

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #5 kdy: 12 Listopadu 2007, 10:51:15 »
prosim k trpezlivosti so mnou..... ako zistim nazov workgroup mojho pocitaca ....pripadne ako ho zmenit potom to uz lahko zeditujem do samba.conf suboru....../etc/samba/smbusers nemam taky subor pricom som podla navodu zadaval prikaz na adduser   ..a ten prikaz co si napisal vyssie ten som nezadaval

nezik

  • Stálý člen
  • **
  • Příspěvků: 723
    • Chalupa Himmelreich
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #6 kdy: 12 Listopadu 2007, 11:40:55 »
já měl při připojení problémy se sdílením, dokud jsem nepovolil nastavení IP přes DHCP.
V případě, že máš domácí síť, kde se nebojíš o data, nepotřebuješ smbusers.
ale je divný, že se ti nezobrazují pracovní skupiny. jestli víš IP adresu nějakého jiného počítače v síti, zkus ho pingnout: Systém -> Správa -> Nástroje pro síť
Ubuntu 16.04
Kdesu není první slovo Hanáckeho opilce po probuzení, ale příkaz systému.
Ubuntu - nejlepší pařba od Diabla II. ;D

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #7 kdy: 12 Listopadu 2007, 11:57:31 »
2 pc - net ethernet - switch - kubuntu

chcem sa napajat na druhy komp a zdielat a zapisovat subory medzi sebou ... urobil som presne vsetko co je napisane vo wiki ohladom samby ....potom som jednoducho otvoril vudialene miesta a vypise mi chybu ze sa nepodarilo najst pracovnu skupinu v mojej lokalnej sieti

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #8 kdy: 12 Listopadu 2007, 12:25:43 »
sakra...stale to nejde..nieco robim zle tak ak tu je niekto ochotny nech mi posle smb.conf ::

2pc, kubuntu
samba, smbfs


1. pracovna skupina: KUBUNTU
2. otvoreny volny pristup k zlozkam /read&write path: /mnt/home/share ---------A NA DRUHOM PC: /read&write path: /home
(ak je niekto este viac ochotnejsi tak 3. alternativa: pristup iba vybranym uzivatelom s heslom, path: "ostava")

Citace
#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentary and a ; for parts of the config file that you
# may wish to enable
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.
#

#======================= Global Settings =======================

[global]

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of

   workgroup = KUBUNTU
   domain logons = no
   domain master = yes

# server string is the equivalent of the NT Description field


# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
;   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
dns proxy = no

# What naming service and in what order should we use to resolve host names
# to IP addresses
;   name resolve order = lmhosts host wins bcast

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = true



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/log.%m

# Put a capping on the size of the log files (in Kb).
max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
;   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# "security = user" is always a good idea. This will require a Unix account
# in this server for every user accessing the server. See
# /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html
# in the samba-doc package for details.
security = share
username map = /etc/samba/smbusers

# You may wish to use password encryption.  See the section on
# 'encrypt passwords' in the smb.conf(5) manpage before enabling.
encrypt passwords = yes

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using.
passdb backend = tdbsam

obey pam restrictions = yes

;   guest account = nobody
invalid users = root

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
;   unix password sync = no

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
passwd program = /usr/bin/passwd %u
passwd chat = *Enter\snew\sUNIX\spassword:* %n\n *Retype\snew\sUNIX\spassword:* %n\n *passwd:*password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default i/mnt/home/other/zvukys 'no'.
;   pam password change = no

########## Domains ###########

# Is this machine able to authenticate users. Both PDC and BDC
# must have this setting enabled. If you are the BDC you must
# change the 'domain master' setting to no
#
;   domain logons = yes
#
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of the user's profile directory
# from the client point of view)
# The following required a [profiles] share to be setup on the
# samba server (see below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
;   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
;   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

########## Printing ##########

# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
;   load printers = yes

# lpr(ng) printing. You may wish to override the location of the
# printcap file
;   printing = bsd
;   printcap name = /etc/printcap

# CUPS printing.  See also the cupsaddsmb(8) manpage in the
# cupsys-client package.
;   printing = cups
;   printcap name = cups

# When using [print$], root is implicitly a 'printer admin', but you can
# also give this right to other users to add drivers and set printer
# properties
;   printer admin = @lpadmin


############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Most people will find that this option gives better performance.
# See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html
# for details
# You may want to add the following on a Linux system:
#         SO_RCVBUF=8192 SO_SNDBUF=8192
socket options = TCP_NODELAY
read only = no
restrict anonymous = no
domain master = no
preferred master = no
max protocol = NT
acl compatibility = winnt
ldap ssl = No
server signing = Auto

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   writable = no
;   share modes = no

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

[printers]
comment = All Printers
browseable = no
path = /var/spool/samba
printable = yes
read only = yes
create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
comment = Printer Drivers
path = /var/lib/samba/printers
read only = yes
# Uncomment to allow remote administration of Windows print drivers.
# Replace 'ntadmin' with the name of the group your admin users are
# members of.
;   write list = root, @ntadmin

# A sample share for sharing your CD-ROM with others.
;[cdrom]
;   comment = Samba server's CD-ROM
;   writable = no
;   locking = no
;   path = /cdrom
;   public = yes

# The next two parameters show how to auto-mount a CD-ROM when the
#   cdrom share is accesed. For this to work /etc/fstab must contain
#   an entry like this:
#
#       /dev/scd0   /cdrom  iso9660 defaults,noauto,ro,user   0 0
#
# The CD-ROM gets unmounted automatically after the connection to the
#
# If you don't want to use auto-mounting/unmounting make sure the CD
#   is mounted on /cdrom
#
;   preexec = /bin/mount /cdrom
;   postexec = /bin/umount /cdrom

[share]
comment = Share Folder
path = /mnt/home/share
guest ok = yes
create mask = 0777
directory mask = 0777
force user = nobody
force group = nogroup

uf

  • Aktivní člen
  • *
  • Příspěvků: 163
Re: !KOMPLET! navod na zdielanie suborov cez SAMBU ..prosim
« Odpověď #9 kdy: 12 Listopadu 2007, 12:54:10 »
mam to nastavene ako si mi poradil....firewall som skusil vypnut ale nepomohlo

strawberry

  • Návštěvník
  • Příspěvků: 97
Re: KOMPLET navod na zdielanie suborov cez SAMBU
« Odpověď #10 kdy: 23 Ledna 2008, 20:31:55 »
Mám problém možná tot u bylo tak se omlouvam:-)

Když ve windowsu se chci přihlásit do adresáře kde mám nasdílené data s Ubuntu kliknu na skupinu pak an pc a vyjede mi tabulka zadejte uzivatelske jmeno a heslo kde ho amm prosim zjistit:-(

strawberry

  • Návštěvník
  • Příspěvků: 97
Re: KOMPLET navod na zdielanie suborov cez SAMBU
« Odpověď #11 kdy: 23 Ledna 2008, 20:56:20 »
pocky trosku pomalu co mám dělat:-)neorzumím tomu:-)

strawberry

  • Návštěvník
  • Příspěvků: 97
Re: KOMPLET navod na zdielanie suborov cez SAMBU
« Odpověď #12 kdy: 23 Ledna 2008, 21:01:00 »
security mam na user jiank

Citace
#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentary and a ; for parts of the config file that you
# may wish to enable
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.
#

#======================= Global Settings =======================

[global]

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
   workgroup = MSHOME

# server string is the equivalent of the NT Description field
   server string = %h server (Samba, Ubuntu)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
;   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
   dns proxy = no

# What naming service and in what order should we use to resolve host names
# to IP addresses
;   name resolve order = lmhosts host wins bcast

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = true



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
   log file = /var/log/samba/log.%m

# Put a capping on the size of the log files (in Kb).
   max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
;   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
   syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
   panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# "security = user" is always a good idea. This will require a Unix account
# in this server for every user accessing the server. See
# /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html
# in the samba-doc package for details.
   security = user

# You may wish to use password encryption.  See the section on
# 'encrypt passwords' in the smb.conf(5) manpage before enabling.
   encrypt passwords = true

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using. 
   passdb backend = tdbsam

   obey pam restrictions = yes

;   guest account = nobody
   invalid users = root

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
;   unix password sync = no

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
   passwd program = /usr/bin/passwd %u
   passwd chat = *Enter\snew\sUNIX\spassword:* %n\n *Retype\snew\sUNIX\spassword:* %n\n *passwd:*password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
;   pam password change = no

########## Domains ###########

# Is this machine able to authenticate users. Both PDC and BDC
# must have this setting enabled. If you are the BDC you must
# change the 'domain master' setting to no
#
;   domain logons = yes
#
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of the user's profile directory
# from the client point of view)
# The following required a [profiles] share to be setup on the
# samba server (see below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
;   logon path = \\%n\%u\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
;   logon home = \\%n\%u

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

########## Printing ##########

# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
;   load printers = yes

# lpr(ng) printing. You may wish to override the location of the
# printcap file
;   printing = bsd
;   printcap name = /etc/printcap

# CUPS printing.  See also the cupsaddsmb(8) manpage in the
# cupsys-client package.
;   printcap name = cups

# When using [print$], root is implicitly a 'printer admin', but you can
# also give this right to other users to add drivers and set printer
# properties
;   printer admin = @lpadmin


############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Most people will find that this option gives better performance.
# See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html
# for details
# You may want to add the following on a Linux system:
#         SO_RCVBUF=8192 SO_SNDBUF=8192
;   socket options = TCP_NODELAY

# The following parameter is useful only if you have the linpopup package
# installed. The samba maintainer and the linpopup maintainer are
# working to ease installation and configuration of linpopup and samba.
;   message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' &

# Domain Master specifies Samba to be the Domain Master Browser. If this
# machine will be configured as a BDC (a secondary logon server), you
# must set this to 'no'; otherwise, the default behavior is recommended.
;   domain master = auto

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash
;
; The following was the default behaviour in sarge
; but samba upstream reverted the default because it might induce
; performance issues in large organizations
; See #368251 for some of the consequences of *not* having
; this setting and smb.conf(5) for all details
;
;   winbind enum groups = yes
;   winbind enum users = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares.  This will share each
# user's home directory as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server.  Un-comment the following parameter
# to make sure that only "username" can connect to \\server\username
# This might need tweaking when using external authentication schemes
;   valid users = %S

# By default, the home directories are exported read-only. Change next
# parameter to 'yes' if you want to be able to write to them.
;   writable = no

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   writable = no
;   share modes = no

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

[printers]
   comment = All Printers
   browseable = no
   path = /var/spool/samba
   printable = yes
;   public = no
;   writable = no
   create mode = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
   comment = Printer Drivers
   path = /var/lib/samba/printers
;   browseable = yes
;   read only = yes
;   guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# Replace 'ntadmin' with the name of the group your admin users are
# members of.
;   write list = root, @ntadmin

# A sample share for sharing your CD-ROM with others.
;[cdrom]
;   comment = Samba server's CD-ROM
;   writable = no
;   locking = no
;   path = /cdrom
;   public = yes

# The next two parameters show how to auto-mount a CD-ROM when the
#   cdrom share is accesed. For this to work /etc/fstab must contain
#   an entry like this:
#
#       /dev/scd0   /cdrom  iso9660 defaults,noauto,ro,user   0 0
#
# The CD-ROM gets unmounted automatically after the connection to the
#
# If you don't want to use auto-mounting/unmounting make sure the CD
#   is mounted on /cdrom
#
;   preexec = /bin/mount /cdrom
;   postexec = /bin/umount /cdrom

strawberry

  • Návštěvník
  • Příspěvků: 97
Re: KOMPLET navod na zdielanie suborov cez SAMBU
« Odpověď #13 kdy: 23 Ledna 2008, 21:12:32 »
když dám uložit...vypíše to
Citace
Nemáte oprávnění pro uložení souboru. Zkontrolujte prosím že jste umístění napsali správně. a zksute to znovu
musím být přihlášen jako root nebo kde je chyba?

strawberry

  • Návštěvník
  • Příspěvků: 97
Re: KOMPLET navod na zdielanie suborov cez SAMBU
« Odpověď #14 kdy: 23 Ledna 2008, 21:23:18 »
jej...a to se prosím dělá jak spíěe co adat do terminálu?

strawberry

  • Návštěvník
  • Příspěvků: 97
Re: KOMPLET navod na zdielanie suborov cez SAMBU
« Odpověď #15 kdy: 23 Ledna 2008, 21:41:16 »
děkuji za pomoc už to jde bez hesla..
Ještě se chci zeptat zda se nedá nastavit přístupové jméno a heslo aby se pod winodwsem dopstal do sdílených složek jen při zadání?
« Poslední změna: 23 Ledna 2008, 21:44:13 od strawberry »

 

Provoz zaštiťuje spolek OpenAlt.