v prvom rade vdaka za odpovede

lspci som skusal uz (nasiel som to tu vo fore niekde) ale nevypise nic uzitocne...
Toto je vypis:
00:00.0 Host bridge: nVidia Corporation Unknown device 07c5 (rev a2)
00:00.1 RAM memory: nVidia Corporation Unknown device 07cb (rev a2)
00:01.0 RAM memory: nVidia Corporation Unknown device 07cd (rev a1)
00:01.1 RAM memory: nVidia Corporation Unknown device 07ce (rev a1)
00:01.2 RAM memory: nVidia Corporation Unknown device 07cf (rev a1)
00:01.3 RAM memory: nVidia Corporation Unknown device 07d0 (rev a1)
00:01.4 RAM memory: nVidia Corporation Unknown device 07d1 (rev a1)
00:01.5 RAM memory: nVidia Corporation Unknown device 07d2 (rev a1)
00:01.6 RAM memory: nVidia Corporation Unknown device 07d3 (rev a1)
00:02.0 RAM memory: nVidia Corporation Unknown device 07d6 (rev a1)
00:03.0 ISA bridge: nVidia Corporation Unknown device 07d7 (rev a2)
00:03.1 SMBus: nVidia Corporation Unknown device 07d8 (rev a1)
00:03.2 RAM memory: nVidia Corporation Unknown device 07d9 (rev a1)
00:03.3 Co-processor: nVidia Corporation Unknown device 07da (rev a2)
00:03.4 RAM memory: nVidia Corporation Unknown device 07c8 (rev a1)
00:04.0 USB Controller: nVidia Corporation Unknown device 07fe (rev a1)
00:04.1 USB Controller: nVidia Corporation Unknown device 056a (rev a1)
00:08.0 IDE interface: nVidia Corporation Unknown device 056c (rev a1)
00:09.0 Audio device: nVidia Corporation Unknown device 07fc (rev a1)
00:0a.0 PCI bridge: nVidia Corporation Unknown device 056d (rev a1)
00:0b.0 PCI bridge: nVidia Corporation Unknown device 056e (rev a1)
00:0c.0 PCI bridge: nVidia Corporation Unknown device 056f (rev a1)
00:0d.0 PCI bridge: nVidia Corporation Unknown device 056f (rev a1)
00:0e.0 RAID bus controller: nVidia Corporation Unknown device 07f8 (rev a2)
00:0f.0 Ethernet controller: nVidia Corporation Unknown device 07dc (rev a2)
00:10.0 VGA compatible controller: nVidia Corporation Unknown device 07e5 (rev a2)
01:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0)
Gtf som skusal tiez, s tym uz mam skusenosti z davnejsich dob... skusal som s 1024 768 60
to co mi vratilo som doplnil do xorg.conf na miesto kam to patri (section monitor)
modeline som menil... nezabera nic...
po instalacii programu hwinfo a spusteni prikazu hwinfo mi rozhodilo terminal na mindarre...
toto je koniec vypisu:
85: N⎺┼␊ 00.0: 10701 E├␊⎼┼␊├
[C⎼␊▒├␊␍ ▒├ ┼␊├.125]
UDI: /⎺⎼±/°⎼␊␊␍␊⎽┐├⎺⎻/H▒┌/␍␊┴␋␌␊⎽/┼␊├_00_21_85_09_6␍_␉1
U┼␋─┤␊ ID: ┤⎽DW.┼␍⎻␊┤␌▒│6V1
P▒⎼␊┼├ ID: ⎼BUF.6␉ZS␋WSU␋␊F
S≤⎽FS ID: /␌┌▒⎽⎽/┼␊├/␊├0
S≤⎽FS D␊┴␋␌␊ L␋┼┐: /␍␊┴␋␌␊⎽/⎻␌␋0000:00/0000:00:0°.0
H▒⎼␍┬▒⎼␊ C┌▒⎽⎽: ┼␊├┬⎺⎼┐ ␋┼├␊⎼°▒␌␊
M⎺␍␊┌: "E├␊⎼┼␊├ ┼␊├┬⎺⎼┐ ␋┼├␊⎼°▒␌␊"
D⎼␋┴␊⎼: "°⎺⎼␌␊␍␊├"
D⎼␋┴␊⎼ M⎺␍┤┌␊⎽: "°⎺⎼␌␊␍␊├"
D␊┴␋␌␊ F␋┌␊: ␊├0
HW A␍␍⎼␊⎽⎽: 00:21:85:09:6␍:␉1
L␋┼┐ ␍␊├␊␌├␊␍: ≤␊⎽
C⎺┼°␋± S├▒├┤⎽: ␌°±=┼␊┬, ▒┴▒␋┌=≤␊⎽, ┼␊␊␍=┼⎺, ▒␌├␋┴␊=┤┼┐┼⎺┬┼
A├├▒␌␊␍ ├⎺: #36 (E├␊⎼┼␊├ ␌⎺┼├⎼⎺┌┌␊⎼)
▒├├␋┌▒@A␌␊⎼-A├├␋┌▒:·$ ┌⎽⎻␌␋ ≠ ±⎼␊⎻ -␋ ▒┤␍␋⎺
00:09.0 A┤␍␋⎺ ␍␊┴␋␌␊: ┼V␋␍␋▒ C⎺⎼⎻⎺⎼▒├␋⎺┼ U┼┐┼⎺┬┼ ␍␊┴␋␌␊ 07°␌ (⎼␊┴ ▒1)
▒├├␋┌▒@A␌␊⎼-A├├␋┌▒:·$ ┌⎽⎻␌␋ ≠ ±⎼␊⎻ -␋ ▒┤␍␋⎺
prikaz lspci | grep -i audio uz ani nemozem zadat, lebo mi pise takto rozhadzane...
ak ho zadam bez predchadzajuceho hwinfo, vrati mi toto:
nVidia Corporation Unknown device 07fc (rev a1)
aplay -l vrati:
aplay: device_list:204: no soundcards found...
dmesg mi vrati toto, ale ja tomu zial vobec nerozumiem:
[ 0.000000] Linux version 2.6.22-15-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Wed Aug 20 18:39:13 UTC 2008 (Ubuntu 2.6.22-15.58-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
[ 0.000000] BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000affa0000 (usable)
[ 0.000000] BIOS-e820: 00000000affa0000 - 00000000affae000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000affae000 - 00000000affe0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000affe0000 - 00000000affee000 (reserved)
[ 0.000000] BIOS-e820: 00000000afff0000 - 00000000b0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] 1919MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 720800) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 720800
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 720800
[ 0.000000] On node 0 totalpages: 720800
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 3839 pages used for memmap
[ 0.000000] HighMem zone: 487585 pages, LIFO batch:31
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FA4E0 checksum 0
[ 0.000000] ACPI: RSDP 000FA4E0, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT AFFA0000, 004C (r1 ACRSYS ACRPRDCT 20080523 MSFT 97)
[ 0.000000] ACPI: FACP AFFA0200, 0084 (r1 052308 FACP1637 20080523 MSFT 97)
[ 0.000000] ACPI: DSDT AFFA0620, 6464 (r1 A7399 A7399214 214 INTL 20051117)
[ 0.000000] ACPI: FACS AFFAE000, 0040
[ 0.000000] ACPI: APIC AFFA0390, 0080 (r1 052308 APIC1637 20080523 MSFT 97)
[ 0.000000] ACPI: MCFG AFFA0410, 003C (r1 052308 OEMMCFG 20080523 MSFT 97)
[ 0.000000] ACPI: SLIC AFFA0450, 0176 (r1 ACRSYS ACRPRDCT 20080523 MSFT 97)
[ 0.000000] ACPI: WDRT AFFA05D0, 0047 (r1 052308 NV-WDRT 20080523 MSFT 97)
[ 0.000000] ACPI: OEMB AFFAE040, 0071 (r1 052308 OEMB1637 20080523 MSFT 97)
[ 0.000000] ACPI: HPET AFFA6A90, 0038 (r1 052308 OEMHPET0 20080523 MSFT 97)
[ 0.000000] ACPI: NVHD AFFAE0C0, 0554 (r1 052308 NVHDCP 20080523 MSFT 97)
[ 0.000000] ACPI: AWMI AFFAE620, 004E (r1 052308 OEMB1637 20080523 MSFT 97)
[ 0.000000] ACPI: SSDT AFFAEF90, 0A7C (r1 DpgPmm CpuPm 12 INTL 20051117)
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at b8000000 (gap: b0000000:4ec00000)
[ 0.000000] Built 1 zonelists. Total pages: 715169
[ 0.000000] Kernel command line: root=UUID=4b5235e0-8b0f-4baf-a0a3-d2c55c055f3f ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1999.944 MHz processor.
[ 45.458194] spurious 8259A interrupt: IRQ7.
[ 45.460987] Console: colour VGA+ 80x25
[ 45.461376] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 45.461679] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 45.582957] Memory: 2847588k/2883200k available (2016k kernel code, 34308k reserved, 919k data, 364k init, 1965696k highmem)
[ 45.582965] virtual kernel memory layout:
[ 45.582966] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 45.582967] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 45.582968] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 45.582969] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 45.582970] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 45.582970] .data : 0xc02f8086 - 0xc03dde84 ( 919 kB)
[ 45.582971] .text : 0xc0100000 - 0xc02f8086 (2016 kB)
[ 45.582974] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 45.583009] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 45.583141] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 45.583145] hpet0: 3 32-bit timers, 25000000 Hz
[ 45.664162] Calibrating delay using timer specific routine.. 4004.18 BogoMIPS (lpj=8008379)
[ 45.664183] Security Framework v1.0.0 initialized
[ 45.664189] SELinux: Disabled at boot.
[ 45.664200] Mount-cache hash table entries: 512
[ 45.664317] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
[ 45.664324] monitor/mwait feature present.
[ 45.664326] using mwait in idle threads.
[ 45.664330] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 45.664332] CPU: L2 cache: 1024K
[ 45.664334] CPU: Physical Processor ID: 0
[ 45.664335] CPU: Processor Core ID: 0
[ 45.664337] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e39d 00000000 00000001
[ 45.664346] Compat vDSO mapped to ffffe000.
[ 45.664357] Checking 'hlt' instruction... OK.
[ 45.680288] SMP alternatives: switching to UP code
[ 45.680671] Early unpacking initramfs... done
[ 45.957399] ACPI: Core revision 20070126
[ 45.957439] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 45.960388] CPU0: Intel(R) Pentium(R) Dual CPU E2180 @ 2.00GHz stepping 0d
[ 45.960402] SMP alternatives: switching to SMP code
[ 45.960484] Booting processor 1/1 eip 3000
[ 45.970564] Initializing CPU#1
[ 46.048146] Calibrating delay using timer specific routine.. 3999.91 BogoMIPS (lpj=7999821)
[ 46.048152] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
[ 46.048156] monitor/mwait feature present.
[ 46.048158] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 46.048160] CPU: L2 cache: 1024K
[ 46.048161] CPU: Physical Processor ID: 0
[ 46.048163] CPU: Processor Core ID: 1
[ 46.048164] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e39d 00000000 00000001
[ 46.048489] CPU1: Intel(R) Pentium(R) Dual CPU E2180 @ 2.00GHz stepping 0d
[ 46.048507] Total of 2 processors activated (8004.10 BogoMIPS).
[ 46.048703] ENABLING IO-APIC IRQs
[ 46.048901] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 46.196220] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 46.216231] Brought up 2 CPUs
[ 46.320871] migration_cost=102
[ 46.320979] Booting paravirtualized kernel on bare hardware
[ 46.321042] Time: 17:45:51 Date: 08/21/108
[ 46.321058] NET: Registered protocol family 16
[ 46.321127] EISA bus registered
[ 46.321131] ACPI: bus type pci registered
[ 46.321289] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
[ 46.321291] PCI: Using configuration type 1
[ 46.321292] Setting up standard PCI resources
[ 46.328991] ACPI: EC: Look up EC in DSDT
[ 46.331410] ACPI: System BIOS is requesting _OSI(Linux)
[ 46.331412] ACPI: Please test with "acpi_osi=!Linux"
[ 46.331413] Please send dmidecode to linux-acpi@vger.kernel.org
[ 46.335487] ACPI: Interpreter enabled
[ 46.335489] ACPI: (supports S0 S1 S3 S4 S5)
[ 46.335505] ACPI: Using IOAPIC for interrupt routing
[ 46.335707] Error attaching device data
[ 46.335741] Error attaching device data
[ 46.335775] Error attaching device data
[ 46.335808] Error attaching device data
[ 46.345764] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 46.345770] PCI: Probing PCI hardware (bus 00)
[ 46.347368] PCI: Transparent bridge - 0000:00:0a.0
[ 46.347630] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 46.347839] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 46.347996] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
[ 46.348092] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
[ 46.348219] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
[ 46.359284] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 46.359507] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 46.359729] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 46.359953] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *10
[ 46.360203] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
[ 46.360434] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
[ 46.360671] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
[ 46.360896] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
[ 46.361117] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
[ 46.361336] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
[ 46.361556] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *7
[ 46.361775] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *7
[ 46.361994] ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *10
[ 46.362244] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
[ 46.362486] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *7
[ 46.362709] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[ 46.362885] ACPI Error (uteval-0293): Return object type is incorrect [\_SB_.LATA._CRS] (Node df8037c8), AE_TYPE
[ 46.362891] ACPI Error (uteval-0299): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20070126]
[ 46.362896] ACPI Exception (pci_link-0277): AE_TYPE, Evaluating _CRS [20070126]
[ 46.362899] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 46.363015] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 46.363024] pnp: PnP ACPI init
[ 46.363031] ACPI: bus type pnp registered
[ 46.368621] pnp: PnP ACPI: found 14 devices
[ 46.368623] ACPI: ACPI bus type pnp unregistered
[ 46.368627] PnPBIOS: Disabled by ACPI PNP
[ 46.368671] PCI: Using ACPI for IRQ routing
[ 46.368673] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 46.384928] NET: Registered protocol family 8
[ 46.384930] NET: Registered protocol family 20
[ 46.384975] pnp: 00:06: iomem range 0xfec80000-0xfed3ffff has been reserved
[ 46.384977] pnp: 00:06: iomem range 0xfed45000-0xfd93ffff could not be reserved
[ 46.384980] pnp: 00:06: iomem range 0xfefe0000-0xfefe01ff has been reserved
[ 46.384982] pnp: 00:06: iomem range 0xfefe1000-0xfefe1fff has been reserved
[ 46.384988] pnp: 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 46.384990] pnp: 00:08: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 46.384996] pnp: 00:0b: ioport range 0xa00-0xa0f has been reserved
[ 46.384998] pnp: 00:0b: ioport range 0xa10-0xa1f has been reserved
[ 46.385000] pnp: 00:0b: ioport range 0xa20-0xa2f has been reserved
[ 46.385002] pnp: 00:0b: ioport range 0xa30-0xa3f has been reserved
[ 46.385006] pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
[ 46.385011] pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 46.385013] pnp: 00:0d: iomem range 0x0-0x0 could not be reserved
[ 46.385015] pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 46.385017] pnp: 00:0d: iomem range 0x100000-0xbfffffff could not be reserved
[ 46.388141] Time: tsc clocksource has been installed.
[ 46.388148] Switched to high resolution mode on CPU 0
[ 46.388222] Switched to high resolution mode on CPU 1
[ 46.415268] PCI: Bridge: 0000:00:0a.0
[ 46.415271] IO window: e000-efff
[ 46.415275] MEM window: feb00000-febfffff
[ 46.415278] PREFETCH window: disabled.
[ 46.415281] PCI: Bridge: 0000:00:0b.0
[ 46.415282] IO window: disabled.
[ 46.415285] MEM window: disabled.
[ 46.415287] PREFETCH window: disabled.
[ 46.415290] PCI: Bridge: 0000:00:0c.0
[ 46.415292] IO window: disabled.
[ 46.415294] MEM window: disabled.
[ 46.415297] PREFETCH window: disabled.
[ 46.415300] PCI: Bridge: 0000:00:0d.0
[ 46.415301] IO window: disabled.
[ 46.415304] MEM window: disabled.
[ 46.415306] PREFETCH window: disabled.
[ 46.415317] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 46.415328] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 46.415337] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 46.415346] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 46.415355] NET: Registered protocol family 2
[ 46.460144] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 46.460240] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 46.461007] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 46.461431] TCP: Hash tables configured (established 131072 bind 65536)
[ 46.461433] TCP reno registered
[ 46.476300] checking if image is initramfs... it is
[ 47.022854] Freeing initrd memory: 7041k freed
[ 47.023354] audit: initializing netlink socket (disabled)
[ 47.023369] audit(1222019151.180:1): initialized
[ 47.023453] highmem bounce pool size: 64 pages
[ 47.025006] VFS: Disk quotas dquot_6.5.1
[ 47.025045] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 47.025121] io scheduler noop registered
[ 47.025123] io scheduler anticipatory registered
[ 47.025125] io scheduler deadline registered
[ 47.025136] io scheduler cfq registered (default)
[ 47.047316] Boot video device is 0000:00:10.0
[ 47.047396] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 47.047430] assign_interrupt_mode Found MSI capability
[ 47.047433] Allocate Port Service[0000:00:0b.0:pcie00]
[ 47.047502] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 47.047536] assign_interrupt_mode Found MSI capability
[ 47.047538] Allocate Port Service[0000:00:0c.0:pcie00]
[ 47.047603] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 47.047637] assign_interrupt_mode Found MSI capability
[ 47.047639] Allocate Port Service[0000:00:0d.0:pcie00]
[ 47.047752] isapnp: Scanning for PnP cards...
[ 47.400639] isapnp: No Plug & Play device found
[ 47.418117] Real Time Clock Driver v1.12ac
[ 47.418211] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 47.418303] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 47.418437] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 47.418878] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 47.419078] 00:05: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 47.419663] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 47.419791] input: Macintosh mouse button emulation as /class/input/input0
[ 47.419857] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 47.420176] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 47.420180] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 47.420308] mice: PS/2 mouse device common for all mice
[ 47.420396] EISA: Probing bus 0 at eisa.0
[ 47.420410] Cannot allocate resource for EISA slot 4
[ 47.420423] EISA: Detected 0 cards.
[ 47.420502] TCP cubic registered
[ 47.420514] NET: Registered protocol family 1
[ 47.420532] Using IPI No-Shortcut mode
[ 47.420690] Magic number: 8:635:795
[ 47.420756] hash matches device ptyr3
[ 47.420964] Freeing unused kernel memory: 364k freed
[ 47.456583] input: AT Translated Set 2 keyboard as /class/input/input1
[ 48.589165] AppArmor: AppArmor initialized<5>audit(1222019152.680:2): type=1505 info="AppArmor initialized" pid=1242
[ 48.595790] fuse init (API version 7.8)
[ 48.599674] Failure registering capabilities with primary security module.
[ 48.632104] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - EE, should be EB [20070126]
[ 48.632112] ACPI: SSDT AFFAE670, 0235 (r1 DpgPmm P001Ist 11 INTL 20051117)
[ 48.632336] ACPI: Processor [P001] (supports 8 throttling states)
[ 48.632526] ACPI: SSDT AFFAEB00, 0235 (r1 DpgPmm P002Ist 12 INTL 20051117)
[ 48.632728] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 48.632737] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 48.633585] ACPI: Invalid passive threshold
[ 48.633711] ACPI: Thermal Zone [THRM] (24 C)
[ 49.045059] usbcore: registered new interface driver usbfs
[ 49.045079] usbcore: registered new interface driver hub
[ 49.045097] usbcore: registered new device driver usb
[ 49.046264] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 23
[ 49.046270] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [LUB2] -> GSI 23 (level, low) -> IRQ 16
[ 49.046280] PCI: Setting latency timer of device 0000:00:04.1 to 64
[ 49.046283] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 49.046399] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 49.046420] ehci_hcd 0000:00:04.1: debug port 1
[ 49.046424] PCI: cache line size of 32 is not supported by device 0000:00:04.1
[ 49.046433] ehci_hcd 0000:00:04.1: irq 16, io mem 0xfea7ec00
[ 49.046440] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 49.046515] usb usb1: configuration #1 chosen from 1 choice
[ 49.046538] hub 1-0:1.0: USB hub found
[ 49.046546] hub 1-0:1.0: 8 ports detected
[ 49.055622] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 49.055625] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 49.084375] SCSI subsystem initialized
[ 49.088537] libata version 2.21 loaded.
[ 49.099957] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 49.143680] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 49.148864] ahci 0000:00:0e.0: version 2.2
[ 49.149238] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 22
[ 49.149244] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LSA0] -> GSI 22 (level, low) -> IRQ 17
[ 49.867854] usb 1-5: new high speed USB device using ehci_hcd and address 4
[ 50.000898] usb 1-5: configuration #1 chosen from 1 choice
[ 50.151838] ahci 0000:00:0e.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
[ 50.151845] ahci 0000:00:0e.0: flags: 64bit led clo pmp pio
[ 50.151852] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 50.152110] scsi0 : ahci
[ 50.152166] scsi1 : ahci
[ 50.152196] scsi2 : ahci
[ 50.152228] scsi3 : ahci
[ 50.152304] ata1: SATA max UDMA/133 cmd 0xf8894100 ctl 0x00000000 bmdma 0x00000000 irq 17
[ 50.152307] ata2: SATA max UDMA/133 cmd 0xf8894180 ctl 0x00000000 bmdma 0x00000000 irq 17
[ 50.152310] ata3: SATA max UDMA/133 cmd 0xf8894200 ctl 0x00000000 bmdma 0x00000000 irq 17
[ 50.152312] ata4: SATA max UDMA/133 cmd 0xf8894280 ctl 0x00000000 bmdma 0x00000000 irq 17
[ 50.239823] usb 1-6: new high speed USB device using ehci_hcd and address 5
[ 50.372897] usb 1-6: configuration #1 chosen from 1 choice
[ 50.373171] usbcore: registered new interface driver libusual
[ 50.376722] Initializing USB Mass Storage driver...
[ 50.376781] scsi4 : SCSI emulation for USB Mass Storage devices
[ 50.376822] usb-storage: device found at 4
[ 50.376823] usb-storage: waiting for device to settle before scanning
[ 50.376853] scsi5 : SCSI emulation for USB Mass Storage devices
[ 50.376883] usb-storage: device found at 5
[ 50.376884] usb-storage: waiting for device to settle before scanning
[ 50.376894] usbcore: registered new interface driver usb-storage
[ 50.376897] USB Mass Storage support registered.
[ 50.635825] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 50.636642] ata1.00: ATA-8: WDC WD3200AAJS-22B4A0, 01.03A01, max UDMA/133
[ 50.636647] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 50.637516] ata1.00: configured for UDMA/133
[ 50.947759] ata2: SATA link down (SStatus 0 SControl 300)
[ 51.435719] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 51.438899] ata3.00: ATAPI: HL-DT-ST DVDRAM GH15F, EG00, max UDMA/100
[ 51.598412] ata3.00: configured for UDMA/100
[ 51.907677] ata4: SATA link down (SStatus 0 SControl 300)
[ 51.907807] scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAJS-2 01.0 PQ: 0 ANSI: 5
[ 51.910747] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GH15F EG00 PQ: 0 ANSI: 5
[ 51.911282] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
[ 51.911288] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LUB0] -> GSI 21 (level, low) -> IRQ 18
[ 51.911300] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 51.911303] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 51.911329] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 51.911343] ohci_hcd 0000:00:04.0: irq 18, io mem 0xfea7f000
[ 51.920467] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 51.920479] sd 0:0:0:0: [sda] Write Protect is off
[ 51.920481] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 51.920494] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 51.920536] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 51.920544] sd 0:0:0:0: [sda] Write Protect is off
[ 51.920546] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 51.920558] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 51.920561] sda: sda1 sda2 sda3 sda4 < sda5 sda6<6>usb usb2: configuration #1 chosen from 1 choice
[ 51.965789] hub 2-0:1.0: USB hub found
[ 51.965797] hub 2-0:1.0: 8 ports detected
[ 51.970035] sda7 >
[ 51.970897] sd 0:0:0:0: [sda] Attached SCSI disk
[ 52.067856] NFORCE-MCP73: IDE controller at PCI slot 0000:00:08.0
[ 52.067882] NFORCE-MCP73: chipset revision 161
[ 52.067883] NFORCE-MCP73: not 100% native mode: will probe irqs later
[ 52.067891] NFORCE-MCP73: 0000:00:08.0 (rev a1) UDMA133 controller
[ 52.067899] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
[ 52.067907] Probing IDE interface ide0...
[ 52.356071] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 52.356077] Uniform CD-ROM driver Revision: 3.20
[ 52.356135] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 52.360840] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 52.360858] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 52.371645] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 52.586782] usb 2-1: configuration #1 chosen from 1 choice
[ 52.589775] scsi6 : SCSI emulation for USB Mass Storage devices
[ 52.589914] usb-storage: device found at 2
[ 52.589915] usb-storage: waiting for device to settle before scanning
[ 52.636007] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
[ 52.636015] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKD] -> GSI 19 (level, low) -> IRQ 19
[ 52.644209] Attempting manual resume
[ 52.644212] swsusp: Resume From Partition 8:6
[ 52.644213] PM: Checking swsusp image.
[ 52.644344] PM: Resume from disk failed.
[ 52.688878] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] MMIO=[febff800-febfffff] Max Packet=[512] IR/IT contexts=[4/8]
[ 52.694379] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 52.694385] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LMAC] -> GSI 20 (level, low) -> IRQ 20
[ 52.694391] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[ 52.694398] forcedeth: using HIGHDMA
[ 52.710686] kjournald starting. Commit interval 5 seconds
[ 52.710696] EXT3-fs: mounted filesystem with ordered data mode.
[ 52.923607] usb 2-3: new full speed USB device using ohci_hcd and address 3
[ 53.141767] usb 2-3: configuration #1 chosen from 1 choice
[ 53.212102] eth0: forcedeth.c: subsystem: 01025:0137 bound to 0000:00:0f.0
[ 53.963634] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00015e2505]
[ 55.375572] usb-storage: device scan complete
[ 55.376440] usb-storage: device scan complete
[ 55.376827] scsi 4:0:0:0: Direct-Access WD 5000AAJ External 1.65 PQ: 0 ANSI: 0
[ 55.376954] scsi 5:0:0:0: Direct-Access WD 5000AAJ External 1.65 PQ: 0 ANSI: 0
[ 55.379548] sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 55.381422] sd 4:0:0:0: [sdb] Write Protect is off
[ 55.381425] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 55.381428] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 55.383447] sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 55.384681] sd 4:0:0:0: [sdb] Write Protect is off
[ 55.384684] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 55.384687] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 55.384691] sdb: sdb1
[ 55.405105] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 55.405132] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 55.406546] sd 5:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 55.408422] sd 5:0:0:0: [sdc] Write Protect is off
[ 55.408425] sd 5:0:0:0: [sdc] Mode Sense: 00 00 00 00
[ 55.408428] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 55.410547] sd 5:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 55.413422] sd 5:0:0:0: [sdc] Write Protect is off
[ 55.413425] sd 5:0:0:0: [sdc] Mode Sense: 00 00 00 00
[ 55.413427] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 55.413431] sdc: sdc1 sdc3 sdc4
[ 55.422872] sd 5:0:0:0: [sdc] Attached SCSI disk
[ 55.422896] sd 5:0:0:0: Attached scsi generic sg3 type 0
[ 57.588639] usb-storage: device scan complete
[ 57.595603] scsi 6:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 57.602621] scsi 6:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 57.610600] scsi 6:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 57.616592] scsi 6:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 57.628122] sd 6:0:0:0: [sdd] Attached SCSI removable disk
[ 57.628163] sd 6:0:0:0: Attached scsi generic sg4 type 0
[ 57.639011] sd 6:0:0:1: [sde] Attached SCSI removable disk
[ 57.639051] sd 6:0:0:1: Attached scsi generic sg5 type 0
[ 57.649628] sd 6:0:0:2: [sdf] Attached SCSI removable disk
[ 57.649673] sd 6:0:0:2: Attached scsi generic sg6 type 0
[ 57.660815] sd 6:0:0:3: [sdg] Attached SCSI removable disk
[ 57.660857] sd 6:0:0:3: Attached scsi generic sg7 type 0
[ 58.160355] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 58.256160] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 58.262094] input: PC Speaker as /class/input/input2
[ 58.322926] Linux agpgart interface v0.102 (c) Dave Jones
[ 58.428551] nvidia: module license 'NVIDIA' taints kernel.
[ 58.756333] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
[ 58.756349] usbcore: registered new interface driver usblp
[ 58.756352] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 58.763837] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 23
[ 58.763841] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [SGRU] -> GSI 23 (level, low) -> IRQ 16
[ 58.763850] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 58.763958] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007
[ 58.863611] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 59.015173] loop: module loaded
[ 59.050322] lp: driver loaded but no devices found
[ 59.127392] Adding 14651240k swap on /dev/sda6. Priority:-1 extents:1 across:14651240k
[ 60.075631] EXT3 FS on sda3, internal journal
[ 60.968076] kjournald starting. Commit interval 5 seconds
[ 60.968272] EXT3 FS on sda5, internal journal
[ 60.968278] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.117731] No dock devices found.
[ 62.218602] input: Power Button (FF) as /class/input/input4
[ 62.218775] ACPI: Power Button (FF) [PWRF]
[ 62.234803] input: Power Button (CM) as /class/input/input5
[ 62.234998] ACPI: Power Button (CM) [PWRB]
[ 63.122153] Failure registering capabilities with primary security module.
[ 63.269401] ppdev: user-space parallel port driver
[ 63.678514] audit(1222019167.433:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5001 profile="/usr/sbin/cupsd"
[ 63.970116] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 63.970121] apm: disabled - APM is not SMP safe.
[ 64.542431] Bluetooth: Core ver 2.11
[ 64.542494] NET: Registered protocol family 31
[ 64.542496] Bluetooth: HCI device and connection manager initialized
[ 64.542501] Bluetooth: HCI socket layer initialized
[ 64.652913] Bluetooth: L2CAP ver 2.8
[ 64.652918] Bluetooth: L2CAP socket layer initialized
[ 64.693015] Bluetooth: RFCOMM socket layer initialized
[ 64.693168] Bluetooth: RFCOMM TTY layer initialized
[ 64.693171] Bluetooth: RFCOMM ver 1.8
[ 68.685605] NET: Registered protocol family 17
[ 73.231568] NET: Registered protocol family 10
[ 73.231693] lo: Disabled Privacy Extensions
[ 83.816947] eth0: no IPv6 routers present
[ 155.750831] usb 1-2: new high speed USB device using ehci_hcd and address 6
[ 155.886715] usb 1-2: configuration #1 chosen from 1 choice
[ 155.887080] scsi7 : SCSI emulation for USB Mass Storage devices
[ 155.887133] usb-storage: device found at 6
[ 155.887136] usb-storage: waiting for device to settle before scanning
[ 160.886505] usb-storage: device scan complete
[ 160.887138] scsi 7:0:0:0: Direct-Access USB Flash Memory 5.00 PQ: 0 ANSI: 0 CCS
[ 161.103858] sd 7:0:0:0: [sdh] 8058880 512-byte hardware sectors (4126 MB)
[ 161.105732] sd 7:0:0:0: [sdh] Write Protect is off
[ 161.105737] sd 7:0:0:0: [sdh] Mode Sense: 23 00 00 00
[ 161.105740] sd 7:0:0:0: [sdh] Assuming drive cache: write through
[ 161.110857] sd 7:0:0:0: [sdh] 8058880 512-byte hardware sectors (4126 MB)
[ 161.112733] sd 7:0:0:0: [sdh] Write Protect is off
[ 161.112738] sd 7:0:0:0: [sdh] Mode Sense: 23 00 00 00
[ 161.112741] sd 7:0:0:0: [sdh] Assuming drive cache: write through
[ 161.112745] sdh: sdh1
[ 161.114308] sd 7:0:0:0: [sdh] Attached SCSI removable disk
[ 161.114371] sd 7:0:0:0: Attached scsi generic sg8 type 0
[ 190.113015] usb 1-2: USB disconnect, address 6
alsamixer vrati:
alsamixer: function snd_ctl_open failed for default: No such device
vyzera to, akoby som nemal zvukovku, ale ja ju mam... pod Vistou mi hra v pohode...
dakujem za akekolvek rady