jak rozchodit Leadtek WinFast DTV Dongle Gold

[dredata_zizalka]

mám ubuntu 8.10.
koupila jsem dnes tuhle kartu, po naistalování kaffein a spuštění mi to napsalo že se neleze připojit k soketu.
zkoušela jsem to tedy jinudy: http://wiki.ubuntu.cz/Digit%C3%A1ln%C3%AD%20TV/channels.conf
ale příkaz w_scan-20081106/w_scan -X >> channels.conf mi nejde, vypíše mi to:

zizalka@zizalka-desktop:~$ w_scan-20081106/w_scan -X >> channels.conf
w_scan version 20081106
Info: using DVB adapter auto detection.
main:2762: FATAL: ***** NO USEABLE DVB CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

karta je podle mě zapojená správně, protože souběžně instalvoaný windows XP ji normálně našel. Vypnula jsem kaffein, ale stejně mi to píše toto.
příkaz w_scan -x >> cz-Praha mi nejde, protože neexistuje či co..

už jsem docela zoufalá... určitě je chyba někde úplně na záčátku...

prosím poraďte

Edit: pokus o změnu názvu tématu - pořídila jsem si jinou kartu...

[dredata_zizalka]

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ lspci
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
01:00.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
01:00.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
01:01.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
01:01.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
01:01.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
04:00.0 VGA compatible controller: ATI Technologies Inc Mobility Radeon HD 3450
04:00.1 Audio device: ATI Technologies Inc RV620 Audio device [Radeon HD 34xx Series]
zizalka@zizalka-desktop:~$

a ten příkaz dmesg:
[    0.576078] NetLabel:  domain hash size = 128
[    0.576078] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.576093] NetLabel:  unlabeled traffic allowed by default
[    0.576102] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.576110] hpet0: 3 64-bit timers, 14318180 Hz
[    0.578140] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.578143]    actual entries 65620
[    0.578242] AppArmor: AppArmor Filesystem Enabled
[    0.578264] ACPI: RTC can wake from S4
[    0.580047] Switched to high resolution mode on CPU 0
[    0.580479] Switched to high resolution mode on CPU 1
[    0.584082] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[    0.584102] system 00:08: ioport range 0x290-0x297 has been reserved
[    0.584113] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[    0.584118] system 00:09: ioport range 0x800-0x87f has been reserved
[    0.584123] system 00:09: ioport range 0x480-0x4bf has been reserved
[    0.584127] system 00:09: ioport range 0x900-0x91f has been reserved
[    0.584132] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.584137] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.584142] system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
[    0.584148] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[    0.584161] system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.584166] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.584177] system 00:0e: iomem range 0xf0000000-0xf3ffffff has been reserved
[    0.584189] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[    0.584193] system 00:0f: iomem range 0xc0000-0xdffff could not be reserved
[    0.584198] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[    0.584203] system 00:0f: iomem range 0x100000-0x3fffffff could not be reserved
[    0.619451] pci 0000:00:01.0: PCI bridge, secondary bus 0000:04
[    0.619455] pci 0000:00:01.0:   IO window: 0xe000-0xefff
[    0.619460] pci 0000:00:01.0:   MEM window: 0xdff00000-0xdfffffff
[    0.619464] pci 0000:00:01.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
[    0.619470] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
[    0.619473] pci 0000:00:1c.0:   IO window: 0xd000-0xdfff
[    0.619478] pci 0000:00:1c.0:   MEM window: disabled
[    0.619483] pci 0000:00:1c.0:   PREFETCH window: disabled
[    0.619489] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:02
[    0.619493] pci 0000:00:1c.3:   IO window: 0xc000-0xcfff
[    0.619498] pci 0000:00:1c.3:   MEM window: 0xdfe00000-0xdfefffff
[    0.619503] pci 0000:00:1c.3:   PREFETCH window: disabled
[    0.619510] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[    0.619513] pci 0000:00:1e.0:   IO window: 0xb000-0xbfff
[    0.619519] pci 0000:00:1e.0:   MEM window: 0xdc000000-0xdfdfffff
[    0.619523] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.619540] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.619545] pci 0000:00:01.0: setting latency timer to 64
[    0.619553] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.619558] pci 0000:00:1c.0: setting latency timer to 64
[    0.619566] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.619571] pci 0000:00:1c.3: setting latency timer to 64
[    0.619579] pci 0000:00:1e.0: setting latency timer to 64
[    0.619583] bus: 00 index 0 io port: [0, ffff]
[    0.619585] bus: 00 index 1 mmio: [0, ffffffff]
[    0.619588] bus: 04 index 0 io port: [e000, efff]
[    0.619591] bus: 04 index 1 mmio: [dff00000, dfffffff]
[    0.619593] bus: 04 index 2 mmio: [e0000000, efffffff]
[    0.619595] bus: 04 index 3 mmio: [0, 0]
[    0.619598] bus: 03 index 0 io port: [d000, dfff]
[    0.619600] bus: 03 index 1 mmio: [0, 0]
[    0.619602] bus: 03 index 2 mmio: [0, 0]
[    0.619604] bus: 03 index 3 mmio: [0, 0]
[    0.619607] bus: 02 index 0 io port: [c000, cfff]
[    0.619609] bus: 02 index 1 mmio: [dfe00000, dfefffff]
[    0.619611] bus: 02 index 2 mmio: [0, 0]
[    0.619614] bus: 02 index 3 mmio: [0, 0]
[    0.619616] bus: 01 index 0 io port: [b000, bfff]
[    0.619618] bus: 01 index 1 mmio: [dc000000, dfdfffff]
[    0.619621] bus: 01 index 2 mmio: [0, 0]
[    0.619623] bus: 01 index 3 io port: [0, ffff]
[    0.619625] bus: 01 index 4 mmio: [0, ffffffff]
[    0.619635] NET: Registered protocol family 2
[    0.632125] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.632431] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.632911] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.633259] TCP: Hash tables configured (established 131072 bind 65536)
[    0.633263] TCP reno registered
[    0.640194] NET: Registered protocol family 1
[    0.640350] checking if image is initramfs... it is
[    1.395452] Freeing initrd memory: 8015k freed
[    1.396742] audit: initializing netlink socket (disabled)
[    1.396767] type=2000 audit(1250699566.396:1): initialized
[    1.402261] highmem bounce pool size: 64 pages
[    1.402268] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.404921] VFS: Disk quotas dquot_6.5.1
[    1.405022] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.405142] msgmni has been set to 1761
[    1.405285] io scheduler noop registered
[    1.405288] io scheduler anticipatory registered
[    1.405291] io scheduler deadline registered
[    1.405305] io scheduler cfq registered (default)
[    1.405411] pci 0000:04:00.0: Boot video device
[    1.405585] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    1.405622] pcieport-driver 0000:00:01.0: found MSI capability
[    1.405656] pci_express 0000:00:01.0:pcie00: allocate port service
[    1.405753] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.405787] pcieport-driver 0000:00:1c.0: found MSI capability
[    1.405822] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.405872] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.405973] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[    1.406006] pcieport-driver 0000:00:1c.3: found MSI capability
[    1.406042] pci_express 0000:00:1c.3:pcie00: allocate port service
[    1.406426] isapnp: Scanning for PnP cards...
[    1.759400] isapnp: No Plug & Play device found
[    1.797155] hpet_resources: 0xfed00000 is busy
[    1.797238] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.797374] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.798251] 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.800254] brd: module loaded
[    1.800329] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    1.800472] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    1.800474] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    1.801039] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.808729] mice: PS/2 mouse device common for all mice
[    1.808890] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.808914] rtc0: alarms up to one month, hpet irqs
[    1.809066] EISA: Probing bus 0 at eisa.0
[    1.809094] Cannot allocate resource for EISA slot 8
[    1.809097] EISA: Detected 0 cards.
[    1.809100] cpuidle: using governor ladder
[    1.809104] cpuidle: using governor menu
[    1.809672] TCP cubic registered
[    1.809703] Using IPI No-Shortcut mode
[    1.809918] registered taskstats version 1
[    1.810062]   Magic number: 5:614:540
[    1.810145] pci 0000:01:01.2: hash matches
[    1.810184] rtc_cmos 00:03: setting system clock to 2009-08-19 16:32:48 UTC (1250699568)
[    1.810187] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.810190] EDD information not available.
[    1.810382] Freeing unused kernel memory: 428k freed
[    1.810423] Write protecting the kernel text: 2584k
[    1.810453] Write protecting the kernel read-only data: 940k
[    1.832163] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    1.964672] fuse init (API version 7.9)
[    2.077010] ACPI: SSDT 3FF9E0B0, 01C6 (r1    AMI   CPU1PM        1 INTL 20060113)
[    2.236102] processor ACPI0007:00: registered as cooling_device0
[    2.236108] ACPI: Processor [CPU1] (supports 8 throttling states)
[    2.236432] ACPI: SSDT 3FF9E280, 013A (r1    AMI   CPU2PM        1 INTL 20060113)
[    2.236875] processor ACPI0007:01: registered as cooling_device1
[    2.236880] ACPI: Processor [CPU2] (supports 8 throttling states)
[    2.433673] Floppy drive(s): fd0 is 1.44M
[    2.452199] FDC 0 is a post-1991 82077
[    2.531337] usbcore: registered new interface driver usbfs
[    2.531372] usbcore: registered new interface driver hub
[    2.531423] usbcore: registered new device driver usb
[    2.534762] USB Universal Host Controller Interface driver v3.0
[    2.534820] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    2.534830] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.534834] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.534886] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    2.534920] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00008000
[    2.535070] usb usb1: configuration #1 chosen from 1 choice
[    2.535100] hub 1-0:1.0: USB hub found
[    2.535109] hub 1-0:1.0: 2 ports detected
[    2.581231] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[    2.636804] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    2.636816] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.636820] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.636849] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.636884] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008400
[    2.636997] usb usb2: configuration #1 chosen from 1 choice
[    2.637029] hub 2-0:1.0: USB hub found
[    2.637036] hub 2-0:1.0: 2 ports detected
[    2.639885] No dock devices found.
[    2.666064] SCSI subsystem initialized
[    2.686968] libata version 3.00 loaded.
[    2.740792] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.740804] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.740809] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.740839] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    2.740874] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
[    2.740983] usb usb3: configuration #1 chosen from 1 choice
[    2.741017] hub 3-0:1.0: USB hub found
[    2.741024] hub 3-0:1.0: 2 ports detected
[    2.844777] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    2.844788] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    2.844793] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.844821] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    2.844855] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00009000
[    2.844960] usb usb4: configuration #1 chosen from 1 choice
[    2.844991] hub 4-0:1.0: USB hub found
[    2.844998] hub 4-0:1.0: 2 ports detected
[    2.948851] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    2.948868] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.948872] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.948908] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    2.952829] ehci_hcd 0000:00:1d.7: debug port 1
[    2.952836] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    2.952845] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdbfffc00
[    2.956746] uhci_hcd 0000:01:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[    2.956755] uhci_hcd 0000:01:01.0: UHCI Host Controller
[    2.956786] uhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 6
[    2.956816] uhci_hcd 0000:01:01.0: irq 21, io base 0x0000b400
[    2.956928] usb usb6: configuration #1 chosen from 1 choice
[    2.956960] hub 6-0:1.0: USB hub found
[    2.956968] hub 6-0:1.0: 2 ports detected
[    2.968520] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.164357] usb usb5: configuration #1 chosen from 1 choice
[    3.164389] hub 5-0:1.0: USB hub found
[    3.164399] hub 5-0:1.0: 8 ports detected
[    3.164459] uhci_hcd 0000:01:01.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[    3.164470] uhci_hcd 0000:01:01.1: UHCI Host Controller
[    3.268312] uhci_hcd 0000:01:01.1: new USB bus registered, assigned bus number 7
[    3.268347] uhci_hcd 0000:01:01.1: irq 22, io base 0x0000b800
[    3.268445] usb usb7: configuration #1 chosen from 1 choice
[    3.268475] hub 7-0:1.0: USB hub found
[    3.268487] hub 7-0:1.0: 2 ports detected
[    3.476847] pata_acpi 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    3.476882] pata_acpi 0000:00:1f.1: setting latency timer to 64
[    3.476895] pata_acpi 0000:00:1f.1: PCI INT A disabled
[    3.476915] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.476927] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    3.476945] r8169 0000:02:00.0: setting latency timer to 64
[    3.477345] eth0: RTL8168b/8111b at 0xf8892000, 00:17:31:6c:c4:e4, XID 38000000 IRQ 220
[    3.478488] ehci_hcd 0000:01:01.2: PCI INT C -> GSI 23 (level, low) -> IRQ 23
[    3.478498] ehci_hcd 0000:01:01.2: EHCI Host Controller
[    3.478537] ehci_hcd 0000:01:01.2: new USB bus registered, assigned bus number 8
[    3.478588] ehci_hcd 0000:01:01.2: irq 23, io mem 0xdfdffc00
[    3.478612] pata_acpi 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    3.478636] pata_acpi 0000:00:1f.2: setting latency timer to 64
[    3.478647] pata_acpi 0000:00:1f.2: PCI INT B disabled
[    3.588035] usb 7-1: new low speed USB device using uhci_hcd and address 2
[    3.600037] ehci_hcd 0000:01:01.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.600248] usb usb8: configuration #1 chosen from 1 choice
[    3.600287] hub 8-0:1.0: USB hub found
[    3.600296] hub 8-0:1.0: 4 ports detected
[    3.656061] hub 7-0:1.0: unable to enumerate USB device on port 1
[    3.817041] ata_piix 0000:00:1f.1: version 2.12
[    3.817063] ata_piix 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    3.817121] ata_piix 0000:00:1f.1: setting latency timer to 64
[    3.817219] scsi0 : ata_piix
[    3.817780] scsi1 : ata_piix
[    3.819422] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    3.819426] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    3.980395] ata1.00: ATAPI: Optiarc DVD RW AD-7200A, 1.09, max UDMA/66
[    3.996330] ata1.00: configured for UDMA/66
[    4.112054] usb 7-1: new low speed USB device using uhci_hcd and address 3
[    4.164487] scsi 0:0:0:0: CD-ROM            Optiarc  DVD RW AD-7200A  1.09 PQ: 0 ANSI: 5
[    4.164636] ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    4.164643] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    4.164700] ata_piix 0000:00:1f.2: setting latency timer to 64
[    4.165146] scsi2 : ata_piix
[    4.165442] scsi3 : ata_piix
[    4.165496] ata3: SATA max UDMA/133 cmd 0xa800 ctl 0xa400 bmdma 0x9400 irq 23
[    4.165499] ata4: SATA max UDMA/133 cmd 0xa000 ctl 0x9800 bmdma 0x9408 irq 23
[    4.287848] usb 7-1: configuration #1 chosen from 1 choice
[    4.314600] usbcore: registered new interface driver hiddev
[    4.337966] input: MLK Trust Mouse 15315-02 as /devices/pci0000:00/0000:00:1e.0/0000:01:01.1/usb7/7-1/7-1:1.0/input/input2
[    4.338373] input,hiddev96,hidraw0: USB HID v1.10 Mouse [MLK Trust Mouse 15315-02] on usb-0000:01:01.1-1
[    4.338397] usbcore: registered new interface driver usbhid
[    4.338401] usbhid: v2.6:USB HID core driver
[    4.343432] ata3.00: ATA-7: WDC WD1600AAJS-00PSA0, 05.06H05, max UDMA/133
[    4.343436] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.356520] ata3.00: configured for UDMA/133
[    4.522842] scsi 2:0:0:0: Direct-Access     ATA      WDC WD1600AAJS-0 05.0 PQ: 0 ANSI: 5
[    4.533619] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[    4.533666] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[    4.549215] Driver 'sr' needs updating - please use bus_type methods
[    4.555135] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.555140] Uniform CD-ROM driver Revision: 3.20
[    4.555244] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    4.558397] Driver 'sd' needs updating - please use bus_type methods
[    4.561773] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    4.561793] sd 2:0:0:0: [sda] Write Protect is off
[    4.561796] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.561827] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.561922] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    4.561939] sd 2:0:0:0: [sda] Write Protect is off
[    4.561942] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.561971] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.561975]  sda: sda1 sda2 sda3
[    4.586618] sd 2:0:0:0: [sda] Attached SCSI disk
[    4.869715] PM: Starting manual resume from disk
[    4.869720] PM: Resume from partition 8:3
[    4.869722] PM: Checking hibernation image.
[    4.869902] PM: Resume from disk failed.
[    4.918885] kjournald starting.  Commit interval 5 seconds
[    4.918904] EXT3-fs: mounted filesystem with ordered data mode.
[    9.878266] udevd version 124 started
[   10.216069] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   10.285954] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.333596] Linux agpgart interface v0.103
[   10.424113] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[   10.448031] ACPI: Power Button (FF) [PWRF]
[   10.448186] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[   10.472496] intel_rng: FWH not detected
[   10.480018] ACPI: Power Button (CM) [PWRB]
[   10.904852] iTCO_vendor_support: vendor-support=0
[   10.978120] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   10.978465] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
[   10.978578] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   11.169171] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   11.212051] [fglrx] Maximum main memory to use for locked dma buffers: 926 MBytes.
[   11.212621] [fglrx]   vendor: 1002 device: 95c5 count: 1
[   11.213718] [fglrx] ioport: bar 4, base 0xe000, size: 0x100
[   11.213731] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.213737] pci 0000:04:00.0: setting latency timer to 64
[   11.214816] [fglrx] PAT is enabled successfully!
[   11.214851] [fglrx] module loaded - fglrx 8.54.3 [Oct 10 2008] with 1 minors
[   11.257912] parport_pc 00:07: reported by Plug and Play ACPI
[   11.258016] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   11.446993] Linux video capture interface: v2.00
[   11.455528] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   11.496439] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
[   11.497220] cx8800 0000:01:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   11.500465] cx88[0]: Your board isn't known (yet) to the driver.  You can
[   11.500468] cx88[0]: try to pick one of the existing card configs via
[   11.500469] cx88[0]: card=<n> insmod option.  Updating to the latest
[   11.500470] cx88[0]: version might help as well.
[   11.500475] cx88[0]: Here is a list of valid choices for the card=<n> insmod option:
[   11.500478] cx88[0]:    card=0 -> UNKNOWN/GENERIC
[   11.500480] cx88[0]:    card=1 -> Hauppauge WinTV 34xxx models
[   11.500483] cx88[0]:    card=2 -> GDI Black Gold
[   11.500485] cx88[0]:    card=3 -> PixelView
[   11.500487] cx88[0]:    card=4 -> ATI TV Wonder Pro
[   11.500490] cx88[0]:    card=5 -> Leadtek Winfast 2000XP Expert
[   11.500492] cx88[0]:    card=6 -> AverTV Studio 303 (M126)
[   11.500495] cx88[0]:    card=7 -> MSI TV-@nywhere Master
[   11.500497] cx88[0]:    card=8 -> Leadtek Winfast DV2000
[   11.500500] cx88[0]:    card=9 -> Leadtek PVR 2000
[   11.500502] cx88[0]:    card=10 -> IODATA GV-VCP3/PCI
[   11.500504] cx88[0]:    card=11 -> Prolink PlayTV PVR
[   11.500507] cx88[0]:    card=12 -> ASUS PVR-416
[   11.500509] cx88[0]:    card=13 -> MSI TV-@nywhere
[   11.500511] cx88[0]:    card=14 -> KWorld/VStream XPert DVB-T
[   11.500514] cx88[0]:    card=15 -> DViCO FusionHDTV DVB-T1
[   11.500516] cx88[0]:    card=16 -> KWorld LTV883RF
[   11.500518] cx88[0]:    card=17 -> DViCO FusionHDTV 3 Gold-Q
[   11.500521] cx88[0]:    card=18 -> Hauppauge Nova-T DVB-T
[   11.500523] cx88[0]:    card=19 -> Conexant DVB-T reference design
[   11.500526] cx88[0]:    card=20 -> Provideo PV259
[   11.500528] cx88[0]:    card=21 -> DViCO FusionHDTV DVB-T Plus
[   11.500531] cx88[0]:    card=22 -> pcHDTV HD3000 HDTV
[   11.500533] cx88[0]:    card=23 -> digitalnow DNTV Live! DVB-T
[   11.500536] cx88[0]:    card=24 -> Hauppauge WinTV 28xxx (Roslyn) models
[   11.500538] cx88[0]:    card=25 -> Digital-Logic MICROSPACE Entertainment Center (MEC)
[   11.500541] cx88[0]:    card=26 -> IODATA GV/BCTV7E
[   11.500543] cx88[0]:    card=27 -> PixelView PlayTV Ultra Pro (Stereo)
[   11.500546] cx88[0]:    card=28 -> DViCO FusionHDTV 3 Gold-T
[   11.500548] cx88[0]:    card=29 -> ADS Tech Instant TV DVB-T PCI
[   11.500551] cx88[0]:    card=30 -> TerraTec Cinergy 1400 DVB-T
[   11.500553] cx88[0]:    card=31 -> DViCO FusionHDTV 5 Gold
[   11.500556] cx88[0]:    card=32 -> AverMedia UltraTV Media Center PCI 550
[   11.500558] cx88[0]:    card=33 -> Kworld V-Stream Xpert DVD
[   11.500561] cx88[0]:    card=34 -> ATI HDTV Wonder
[   11.500563] cx88[0]:    card=35 -> WinFast DTV1000-T
[   11.500566] cx88[0]:    card=36 -> AVerTV 303 (M126)
[   11.500568] cx88[0]:    card=37 -> Hauppauge Nova-S-Plus DVB-S
[   11.500570] cx88[0]:    card=38 -> Hauppauge Nova-SE2 DVB-S
[   11.500573] cx88[0]:    card=39 -> KWorld DVB-S 100
[   11.500575] cx88[0]:    card=40 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid
[   11.500578] cx88[0]:    card=41 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profile)
[   11.500581] cx88[0]:    card=42 -> digitalnow DNTV Live! DVB-T Pro
[   11.500583] cx88[0]:    card=43 -> KWorld/VStream XPert DVB-T with cx22702
[   11.500586] cx88[0]:    card=44 -> DViCO FusionHDTV DVB-T Dual Digital
[   11.500589] cx88[0]:    card=45 -> KWorld HardwareMpegTV XPert
[   11.500591] cx88[0]:    card=46 -> DViCO FusionHDTV DVB-T Hybrid
[   11.500594] cx88[0]:    card=47 -> pcHDTV HD5500 HDTV
[   11.500596] cx88[0]:    card=48 -> Kworld MCE 200 Deluxe
[   11.500598] cx88[0]:    card=49 -> PixelView PlayTV P7000
[   11.500601] cx88[0]:    card=50 -> NPG Tech Real TV FM Top 10
[   11.500603] cx88[0]:    card=51 -> WinFast DTV2000 H ver. I (old)
[   11.500606] cx88[0]:    card=52 -> Geniatech DVB-S
[   11.500608] cx88[0]:    card=53 -> Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
[   11.500611] cx88[0]:    card=54 -> Norwood Micro TV Tuner
[   11.500613] cx88[0]:    card=55 -> Shenzhen Tungsten Ages Tech TE-DTV-250 / Swann OEM
[   11.500616] cx88[0]:    card=56 -> Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder
[   11.500619] cx88[0]:    card=57 -> ADS Tech Instant Video PCI
[   11.500622] cx88[0]:    card=58 -> Pinnacle PCTV HD 800i
[   11.500624] cx88[0]:    card=59 -> DViCO FusionHDTV 5 PCI nano
[   11.500626] cx88[0]:    card=60 -> Pinnacle Hybrid PCTV
[   11.500629] cx88[0]:    card=61 -> Winfast TV2000 XP Global
[   11.500631] cx88[0]:    card=62 -> PowerColor RA330
[   11.500634] cx88[0]:    card=63 -> Geniatech X8000-MT DVBT
[   11.500636] cx88[0]:    card=64 -> DViCO FusionHDTV DVB-T PRO
[   11.500638] cx88[0]:    card=65 -> DViCO FusionHDTV 7 Gold
[   11.500641] cx88[0]:    card=66 -> Prolink Pixelview MPEG 8000GT
[   11.500643] cx88[0]:    card=67 -> Kworld PlusTV HD PCI 120 (ATSC 120)
[   11.500646] cx88[0]:    card=68 -> WinFast DTV2000 H ver. J (new)
[   11.500649] cx88[0]: subsystem: 107d:6f38, board: UNKNOWN/GENERIC [card=0,autodetected]
[   11.500652] cx88[0]: TV tuner type -1, Radio tuner type -1
[   11.500805] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
[   11.505595] cx2388x alsa driver version 0.0.6 loaded
[   11.666381] tuner' 0-0061: chip found @ 0xc2 (cx88[0])
[   11.715441] cx88[0]/0: found at 0000:01:00.0, rev: 5, irq: 17, latency: 64, mmio: 0xdc000000
[   11.731597] cx88[0]/0: registered device video0 [v4l2]
[   11.731643] cx88[0]/0: registered device vbi0
[   11.731662] tuner' 0-0061: tuner type not set
[   11.731847] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[   11.731879] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   12.090351] cx88[0]/2: cx2388x 8802 Driver Manager
[   12.090426] HDA Intel 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   12.090461] HDA Intel 0000:04:00.1: setting latency timer to 64
[   12.090633] cx88_audio 0000:01:00.1: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   12.090661] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
[   12.846323] lp0: using parport0 (interrupt-driven).
[   12.983262] Adding 1984016k swap on /dev/sda3.  Priority:-1 extents:1 across:1984016k
[   13.543924] EXT3 FS on sda2, internal journal
[   14.639213] type=1505 audit(1250692380.891:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4154
[   14.824632] type=1505 audit(1250692381.078:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4159
[   14.824847] type=1505 audit(1250692381.078:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4159
[   14.868085] type=1505 audit(1250692381.122:5): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=4163
[   15.035366] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.611862] ACPI: WMI: Mapper loaded
[   16.537265] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   18.656526] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   18.656534] apm: disabled - APM is not SMP safe.
[   18.997783] ppdev: user-space parallel port driver
[   20.697583] NET: Registered protocol family 10
[   20.699024] lo: Disabled Privacy Extensions
[   21.811534] Bluetooth: Core ver 2.13
[   21.812142] NET: Registered protocol family 31
[   21.812149] Bluetooth: HCI device and connection manager initialized
[   21.812154] Bluetooth: HCI socket layer initialized
[   21.853884] Bluetooth: L2CAP ver 2.11
[   21.853892] Bluetooth: L2CAP socket layer initialized
[   21.880273] Bluetooth: SCO (Voice Link) ver 0.6
[   21.880284] Bluetooth: SCO socket layer initialized
[   21.905602] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   21.905612] Bluetooth: BNEP filters: protocol multicast
[   21.956177] Bridge firewalling registered
[   22.080391] Bluetooth: RFCOMM socket layer initialized
[   22.081186] Bluetooth: RFCOMM TTY layer initialized
[   22.081195] Bluetooth: RFCOMM ver 1.10
[   25.087415] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[   25.087426] [fglrx] Reserved FB block: Unshared offset:ff73000, size:88000
[   25.087431] [fglrx] Reserved FB block: Unshared offset:fffc000, size:4000
[   26.192969] r8169: eth0: link down
[   26.194142] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   71.060023] usb 5-1: new high speed USB device using ehci_hcd and address 2
[   71.193359] usb 5-1: configuration #1 chosen from 1 choice
[   71.448022] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[   71.582693] phy0: Selected rate control algorithm 'pid'
[   71.703559] zd1211rw 5-1:1.0: phy0
[   71.704179] usbcore: registered new interface driver zd1211rw
[   75.744276] firmware: requesting zd1211/zd1211b_ub
[   75.799972] firmware: requesting zd1211/zd1211b_uphr
[   75.856671] zd1211rw 5-1:1.0: firmware version 4725
[   75.896673] zd1211rw 5-1:1.0: zd1211b chip 0ace:1215 v4810 high 00-02-72 AL2230_RF pa0 g--NS
[   75.919499] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   76.013708] NET: Registered protocol family 17
[   82.756039] wlan0: authenticate with AP 00:12:0e:9b:e3:34
[   82.757655] wlan0: authenticated
[   82.757664] wlan0: associate with AP 00:12:0e:9b:e3:34
[   82.760032] wlan0: RX AssocResp from 00:12:0e:9b:e3:34 (capab=0x411 status=0 aid=1)
[   82.760039] wlan0: associated
[   82.760980] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   93.300017] wlan0: no IPv6 routers present
[  120.152928] ppdev0: registered pardevice
[  120.200893] ppdev0: unregistered pardevice
[  120.800212] ppdev0: registered pardevice
[  120.848268] ppdev0: unregistered pardevice
[  120.928156] ppdev0: registered pardevice
[  120.976051] ppdev0: unregistered pardevice
zizalka@zizalka-desktop:~$

mám tedy zkusit postupovat, podle vašeho prvního návodu? nebo tento výpis něco mění? (omlouvám se, jsem úplný začátečník  )

edit:

jinak když jsem nakoukla do

nastroj "scan" je v balíku "dvb-apps" ale musíte mít upraven soubor " /usr/share/dvb/dvb-t/cz-Praha" protože jsou tam staré frekvence!

tak ten soubor je prázdný... a v synaptic mi přímo tento balík nenašel...

než mi odpovíte, nejspíš tu budu zkoušet to co jste psal...tak doufám, že mi to pak půjde dát případně zpět 

[jadd]

Karta byla rozpoznána a ovladače jsou už v jádře, takže už jen rozběhat tv aplikaci.
Takže si prostě doinstalte balík dvb-apps (pokud ho nemáte nainstalován nic v něm neuvidíte) a dál postupujte jak sem psal výše.

[dredata_zizalka]

vzhledem k tomu, že mi karta nešla v XP - kde jít měla, tedy respektive šla, ale nic nenaladila. Rozhodla jsem se jí vrátit. Momentálně mám doma jiný zázrak a tod Leadtec  winfast DVT gold nebo tak něco..je to usb adapter, který někde označili jako vhodný pro linux.

přesto se snažím nainstalovat vámi zmíněný balík, ale v synampticu ho nevidím (přímo tento název) ani k instalaci, ani jako nainstalovaný...když jsem v terminálu zadala:

zizalka@zizalka-desktop:~$ sudo apt-get install dvb-apps
Čtu seznamy balíků... Hotovo
Vytvářím strom závislostí       
Čtu stavové informace... Hotovo
E: Nemohu najít balík dvb-apps


prosím prosím o radu

našla jsem rádce přímo pro tu mou novou kartu ( http://pctuning.tyden.cz/hardware/multimedia-zvuk-tv/14743-velky-test-sesti-usb-tv-tuneru-do-tisice-korun?start=17) ale s tou mojí původní hláškou o sekret nepočítají 


další rádce mi radil nainstalova ještě balík utils, tak jsem to zkusila:

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ sudo apt-get install dvb-utils
Čtu seznamy balíků... Hotovo
Vytvářím strom závislostí       
Čtu stavové informace... Hotovo
Následující balíky byly nainstalovány automaticky a již nejsou potřeba:
  lirc pwgen libglib1.2ldbl menu libmpich1.0gf liblzo1 mysql-client
  libnet-daemon-perl libgtk1.2 libqt3-mt-mysql libfame-0.9 python-mysqldb
  libgfortran2 fftw2 toolame libdbi-perl libpvm3 libdbd-mysql-perl
  mysql-server-5.0 mysql-client-5.0 transcode-doc libcarp-clan-perl
  libxml-xql-perl libsox0 libplrpc-perl dvdauthor libparse-yapp-perl
  tango-icon-theme setserial expect mysql-server python-xml ffmpeg transcode
  ntp pvm gcc-4.2-base libsox-fmt-base sox tcl8.4 libgtk1.2-common
  libsox-fmt-alsa libimage-size-perl mjpegtools libnet-upnp-perl perlmagick
  pastebinit vnc4-common libavdevice52
Pro jejich odstranění použijte 'apt-get autoremove'.
Následující NOVÉ balíky budou nainstalovány:
  dvb-utils
0 aktualizováno, 1 nově instalováno, 0 k odstranění a 4 neaktualizováno.
Potřebuji stáhnout 139kB archivů.
Po této operaci bude na disku použito dalších 2916kB.
Mám:1 http://cz.archive.ubuntu.com intrepid/universe dvb-utils 1.1.1-3 [139kB]
Staženo 139kB za 1s (98,3kB/s)   
Instaluji balík dvb-utils.
(Čtu databázi ... nyní je nainstalováno 163388 souborů a adresářů.)
Rozbaluji dvb-utils (z .../dvb-utils_1.1.1-3_i386.deb) ...
Nastavuji balík dvb-utils (1.1.1-3) ...
udev active, devices will be created in /dev/.static/dev/
mkdir: adresář „dvb“ nelze vytvořit: Read-only file system
mkdir: adresář „dvb“ nelze vytvořit: Read-only file system
mknod: „dvb/adapter0/video0-“: No such file or directory
makedev dvb/adapter0/video0 c 212 0 root video 0660: failed
mknod: „dvb/adapter0/audio0-“: No such file or directory
makedev dvb/adapter0/audio0 c 212 1 root video 0660: failed
mknod: „dvb/adapter0/frontend0-“: No such file or directory
makedev dvb/adapter0/frontend0 c 212 3 root video 0660: failed
mknod: „dvb/adapter0/demux0-“: No such file or directory
makedev dvb/adapter0/demux0 c 212 4 root video 0660: failed
mknod: „dvb/adapter0/dvr0-“: No such file or directory
makedev dvb/adapter0/dvr0 c 212 5 root video 0660: failed
mknod: „dvb/adapter0/ca0-“: No such file or directory
makedev dvb/adapter0/ca0 c 212 6 root video 0660: failed
mknod: „dvb/adapter0/net0-“: No such file or directory
makedev dvb/adapter0/net0 c 212 7 root video 0660: failed
mknod: „dvb/adapter0/osd0-“: No such file or directory
makedev dvb/adapter0/osd0 c 212 8 root video 0660: failed
mkdir: adresář „dvb“ nelze vytvořit: Read-only file system
mknod: „dvb/adapter1/video0-“: No such file or directory
makedev dvb/adapter1/video0 c 212 64 root video 0660: failed
mknod: „dvb/adapter1/audio0-“: No such file or directory
makedev dvb/adapter1/audio0 c 212 65 root video 0660: failed
mknod: „dvb/adapter1/frontend0-“: No such file or directory
makedev dvb/adapter1/frontend0 c 212 67 root video 0660: failed
mknod: „dvb/adapter1/demux0-“: No such file or directory
makedev dvb/adapter1/demux0 c 212 68 root video 0660: failed
mknod: „dvb/adapter1/dvr0-“: No such file or directory
makedev dvb/adapter1/dvr0 c 212 69 root video 0660: failed
mknod: „dvb/adapter1/ca0-“: No such file or directory
makedev dvb/adapter1/ca0 c 212 70 root video 0660: failed
mknod: „dvb/adapter1/net0-“: No such file or directory
makedev dvb/adapter1/net0 c 212 71 root video 0660: failed
mknod: „dvb/adapter1/osd0-“: No such file or directory
makedev dvb/adapter1/osd0 c 212 72 root video 0660: failed
mkdir: adresář „dvb“ nelze vytvořit: Read-only file system
mknod: „dvb/adapter2/video0-“: No such file or directory
makedev dvb/adapter2/video0 c 212 128 root video 0660: failed
mknod: „dvb/adapter2/audio0-“: No such file or directory
makedev dvb/adapter2/audio0 c 212 129 root video 0660: failed
mknod: „dvb/adapter2/frontend0-“: No such file or directory
makedev dvb/adapter2/frontend0 c 212 131 root video 0660: failed
mknod: „dvb/adapter2/demux0-“: No such file or directory
makedev dvb/adapter2/demux0 c 212 132 root video 0660: failed
mknod: „dvb/adapter2/dvr0-“: No such file or directory
makedev dvb/adapter2/dvr0 c 212 133 root video 0660: failed
mknod: „dvb/adapter2/ca0-“: No such file or directory
makedev dvb/adapter2/ca0 c 212 134 root video 0660: failed
mknod: „dvb/adapter2/net0-“: No such file or directory
makedev dvb/adapter2/net0 c 212 135 root video 0660: failed
mknod: „dvb/adapter2/osd0-“: No such file or directory
makedev dvb/adapter2/osd0 c 212 136 root video 0660: failed
mkdir: adresář „dvb“ nelze vytvořit: Read-only file system
mknod: „dvb/adapter3/video0-“: No such file or directory
makedev dvb/adapter3/video0 c 212 192 root video 0660: failed
mknod: „dvb/adapter3/audio0-“: No such file or directory
makedev dvb/adapter3/audio0 c 212 193 root video 0660: failed
mknod: „dvb/adapter3/frontend0-“: No such file or directory
makedev dvb/adapter3/frontend0 c 212 195 root video 0660: failed
mknod: „dvb/adapter3/demux0-“: No such file or directory
makedev dvb/adapter3/demux0 c 212 196 root video 0660: failed
mknod: „dvb/adapter3/dvr0-“: No such file or directory
makedev dvb/adapter3/dvr0 c 212 197 root video 0660: failed
mknod: „dvb/adapter3/ca0-“: No such file or directory
makedev dvb/adapter3/ca0 c 212 198 root video 0660: failed
mknod: „dvb/adapter3/net0-“: No such file or directory
makedev dvb/adapter3/net0 c 212 199 root video 0660: failed
mknod: „dvb/adapter3/osd0-“: No such file or directory
makedev dvb/adapter3/osd0 c 212 200 root video 0660: failed

[jadd]

Nemám 8.10 ale podle toho co sem našel na https://launchpad.net/ubuntu/intrepid/+package/dvb-utils, tak to vypadá že už ho máte obsažen v balíku "dvb-utils". Proto zkuste příkaz

Kód: [Vybrat]

which scan nebo

Kód: [Vybrat]

whereis scan pokud se vypíše /usr/bin/scan, tak ho máte v systému.

[dredata_zizalka]

tak podle všeho v systému je..protože odpověď byla ta co jste předpověděl 

ale dál už jsem zase ztracená 

ale musíte mít upraven soubor " /usr/share/dvb/dvb-t/cz-Praha" protože jsou tam staré frekvence!
        Dnes k 18.8.2009  to jsou:
T 570000000 8MHz 2/3 NONE QAM64 8k 1/4 NONE
T 570000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
T 570000000 8MHz 2/3 NONE QAM64 8k 1/16 NONE
T 634000000 8MHz 2/3 NONE QAM64 8k 1/4 NONE
T 634000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
T 634000000 8MHz 2/3 NONE QAM64 8k 1/16 NONE
T 674000000 8MHz 2/3 NONE QAM64 8k 1/4 NONE
T 674000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
T 674000000 8MHz 2/3 NONE QAM64 8k 1/16 NONE
T 730000000 8MHz 2/3 NONE QAM64 8k 1/4 NONE
T 730000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
T 730000000 8MHz 2/3 NONE QAM64 8k 1/16 NONE
T 778000000 8MHz 2/3 NONE QAM64 8k 1/4 NONE
T 778000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
T 778000000 8MHz 2/3 NONE QAM64 8k 1/16 NONE
T 818000000 8MHz 2/3 NONE QAM64 8k 1/4 NONE
T 818000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
T 818000000 8MHz 2/3 NONE QAM64 8k 1/16 NONE

zadala jsem tedy příkaz sudo gedit /usr/share/dvb/dvb-t/cz-Praha
ale otevře se mi prázdný soubor, já tam vložím frekvence výše a když ho chci uložit napíše mi to, že "Nemohu najít soubor /usr/share/dvb/dvb-t/cz-Praha." snažila jsem se tu složku najít ale u share kočím a složka dvb tam vůbec není...

jistě mi radíte správně - jen já jsem úplně mimo. Všechny akce zkouším se zapojenou kartou i bez zapojené karta

v dobré víře (a v režimu pokus-omyl) jsem přesto zkusila:

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ scan /usr/share/dvb/dvb-t/cz-Praha > /home/zizalka/jmenosouboru-třeba-channels.conf
scanning /usr/share/dvb/dvb-t/cz-Praha
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2247: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory


[dredata_zizalka]

to jsem z toho jelen...takhle jsem ho hledala, balíky mám aktualizované a mám tu jen dvbtune((nainstalováno), dvbstream, dvbsnoop, dvbackup, dvb-utils (naisntalováno), liddvb-dev, tinysnmp-module-dvb

ještě jsem to zkoušla (tu už dřív) takto, ale tam si nejsem jistá, jestli je ten příkaz správně - někde jsem to okopírovala:

zizalka@zizalka-desktop:~$ sudo apt-get install dvb-apps
Čtu seznamy balíků... Hotovo
Vytvářím strom závislostí       
Čtu stavové informace... Hotovo
E: Nemohu najít balík dvb-apps

nějaká alternativa by nebyla?? 

edit: konečně se mi povedlo najít pro mě relativně důvěryhodný odkaz (http://packages.ubuntu.com/jaunty/i386/dvb-apps/download) takže se mi povedlo ho stáhnout.... jdu to zkusit dokoumat

edit2: tak  jsem se snažila postoupit dál...ale asi na to jdu špatně. dala jsem  sudo gedit /usr/share/dvb/dvb-t/cz-Praha soubor obsahoval:

 # DVB-T Praha (Prague, Czech Republic)
# T freq bw fec_hi fec_lo mod transmission-mode guard-interval hierarchy

a nějako 3 frekvence. Zkusila jsem změnit frekvence a text nechat, pak jsem smazala i text

terminál mi povídá:
zizalka@zizalka-desktop:~$ scan /usr/share/dvb/dvb-t/cz-Praha > /home/zizalka/jmenosouboru-třeba-channels.conf
scanning /usr/share/dvb/dvb-t/cz-Praha
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory


mě to zní jako kdyby mi chyběl zase nějaký balíček..ale to bude nejspíš hloupost. Adaptér je zapojený a to včetně dodávané antény...

edit3:
zkusila jsem smazat soubory, které se mi v mých pokusech vytovřili...no...a začalo to vypisovat něco jiného:
zizalka@zizalka-desktop:~$ /usr/share/dvb/dvb-t/cz-Praha > /home/zizalka/jmenosouboru-třeba-channels.conf
bash: /usr/share/dvb/dvb-t/cz-Praha: Permission denied

takže pokus se sudo
zizalka@zizalka-desktop:~$ sudo /usr/share/dvb/dvb-t/cz-Praha > /home/zizalka/jmenosouboru-třeba-channels.conf
sudo: /usr/share/dvb/dvb-t/cz-Praha: command not found

  budu si tu hrát dál, radu ovšem uvítám...plácám se plácám..

edit4
když jsem pokusy zvdala, zkusila jsem nainstalovat Me-tv - překvapivě to po mě chtělo odisnatlovat ten balík apps  tak jsme to zrušila... člověk ho tu tak pracně hledá a me tv mi ho odstraní 

[jadd]

Ty máš ten soubor "cz-Praha" v balíku "dvb-utils", jen je pojmenován "cs-Praha" a je i vjiné cestě http://packages.ubuntu.com/intrepid/i386/dvb-utils/filelist pak stačí tu cestu uvést

Kód: [Vybrat]

scan /cestak_cs-Praha > atd...Problém je ale v tom že ti chybí soubory zařízení v "/dev/dvb/".
Tohle je výstup z tvého "dmesg"

Kód: [Vybrat]

[   11.500465] cx88[0]: Your board isn't known (yet) to the driver.  You can
[   11.500468] cx88[0]: try to pick one of the existing card configs via
[   11.500469] cx88[0]: card=<n> insmod option.  Updating to the latest
[   11.500470] cx88[0]: version might help as well.
[   11.500475] cx88[0]: Here is a list of valid choices for the card=<n> insmod option:
[   11.500478] cx88[0]:    card=0 -> UNKNOWN/GENERIC
[   11.500480] cx88[0]:    card=1 -> Hauppauge WinTV 34xxx models
[   11.500483] cx88[0]:    card=2 -> GDI Black Gold
[   11.500485] cx88[0]:    card=3 -> PixelView
[   11.500487] cx88[0]:    card=4 -> ATI TV Wonder Pro
[   11.500490] cx88[0]:    card=5 -> Leadtek Winfast 2000XP Expert
[   11.500492] cx88[0]:    card=6 -> AverTV Studio 303 (M126)
[   11.500495] cx88[0]:    card=7 -> MSI TV-@nywhere Master
[   11.500497] cx88[0]:    card=8 -> Leadtek Winfast DV2000
[   11.500500] cx88[0]:    card=9 -> Leadtek PVR 2000
[   11.500502] cx88[0]:    card=10 -> IODATA GV-VCP3/PCI
[   11.500504] cx88[0]:    card=11 -> Prolink PlayTV PVR
[   11.500507] cx88[0]:    card=12 -> ASUS PVR-416
[   11.500509] cx88[0]:    card=13 -> MSI TV-@nywhere
[   11.500511] cx88[0]:    card=14 -> KWorld/VStream XPert DVB-T
[   11.500514] cx88[0]:    card=15 -> DViCO FusionHDTV DVB-T1
[   11.500516] cx88[0]:    card=16 -> KWorld LTV883RF
[   11.500518] cx88[0]:    card=17 -> DViCO FusionHDTV 3 Gold-Q
[   11.500521] cx88[0]:    card=18 -> Hauppauge Nova-T DVB-T
[   11.500523] cx88[0]:    card=19 -> Conexant DVB-T reference design
[   11.500526] cx88[0]:    card=20 -> Provideo PV259
[   11.500528] cx88[0]:    card=21 -> DViCO FusionHDTV DVB-T Plus
[   11.500531] cx88[0]:    card=22 -> pcHDTV HD3000 HDTV
[   11.500533] cx88[0]:    card=23 -> digitalnow DNTV Live! DVB-T
[   11.500536] cx88[0]:    card=24 -> Hauppauge WinTV 28xxx (Roslyn) models
[   11.500538] cx88[0]:    card=25 -> Digital-Logic MICROSPACE Entertainment Center (MEC)
[   11.500541] cx88[0]:    card=26 -> IODATA GV/BCTV7E
[   11.500543] cx88[0]:    card=27 -> PixelView PlayTV Ultra Pro (Stereo)
[   11.500546] cx88[0]:    card=28 -> DViCO FusionHDTV 3 Gold-T
[   11.500548] cx88[0]:    card=29 -> ADS Tech Instant TV DVB-T PCI
[   11.500551] cx88[0]:    card=30 -> TerraTec Cinergy 1400 DVB-T
[   11.500553] cx88[0]:    card=31 -> DViCO FusionHDTV 5 Gold
[   11.500556] cx88[0]:    card=32 -> AverMedia UltraTV Media Center PCI 550
[   11.500558] cx88[0]:    card=33 -> Kworld V-Stream Xpert DVD
[   11.500561] cx88[0]:    card=34 -> ATI HDTV Wonder
[   11.500563] cx88[0]:    card=35 -> WinFast DTV1000-T
[   11.500566] cx88[0]:    card=36 -> AVerTV 303 (M126)
[   11.500568] cx88[0]:    card=37 -> Hauppauge Nova-S-Plus DVB-S
[   11.500570] cx88[0]:    card=38 -> Hauppauge Nova-SE2 DVB-S
[   11.500573] cx88[0]:    card=39 -> KWorld DVB-S 100
[   11.500575] cx88[0]:    card=40 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid
[   11.500578] cx88[0]:    card=41 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profile)
[   11.500581] cx88[0]:    card=42 -> digitalnow DNTV Live! DVB-T Pro
[   11.500583] cx88[0]:    card=43 -> KWorld/VStream XPert DVB-T with cx22702
[   11.500586] cx88[0]:    card=44 -> DViCO FusionHDTV DVB-T Dual Digital
[   11.500589] cx88[0]:    card=45 -> KWorld HardwareMpegTV XPert
[   11.500591] cx88[0]:    card=46 -> DViCO FusionHDTV DVB-T Hybrid
[   11.500594] cx88[0]:    card=47 -> pcHDTV HD5500 HDTV
[   11.500596] cx88[0]:    card=48 -> Kworld MCE 200 Deluxe
[   11.500598] cx88[0]:    card=49 -> PixelView PlayTV P7000
[   11.500601] cx88[0]:    card=50 -> NPG Tech Real TV FM Top 10
[   11.500603] cx88[0]:    card=51 -> WinFast DTV2000 H ver. I (old)
[   11.500606] cx88[0]:    card=52 -> Geniatech DVB-S
[   11.500608] cx88[0]:    card=53 -> Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
[   11.500611] cx88[0]:    card=54 -> Norwood Micro TV Tuner
[   11.500613] cx88[0]:    card=55 -> Shenzhen Tungsten Ages Tech TE-DTV-250 / Swann OEM
[   11.500616] cx88[0]:    card=56 -> Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder
[   11.500619] cx88[0]:    card=57 -> ADS Tech Instant Video PCI
[   11.500622] cx88[0]:    card=58 -> Pinnacle PCTV HD 800i
[   11.500624] cx88[0]:    card=59 -> DViCO FusionHDTV 5 PCI nano
[   11.500626] cx88[0]:    card=60 -> Pinnacle Hybrid PCTV
[   11.500629] cx88[0]:    card=61 -> Winfast TV2000 XP Global
[   11.500631] cx88[0]:    card=62 -> PowerColor RA330
[   11.500634] cx88[0]:    card=63 -> Geniatech X8000-MT DVBT
[   11.500636] cx88[0]:    card=64 -> DViCO FusionHDTV DVB-T PRO
[   11.500638] cx88[0]:    card=65 -> DViCO FusionHDTV 7 Gold
[   11.500641] cx88[0]:    card=66 -> Prolink Pixelview MPEG 8000GT
[   11.500643] cx88[0]:    card=67 -> Kworld PlusTV HD PCI 120 (ATSC 120)
[   11.500646] cx88[0]:    card=68 -> WinFast DTV2000 H ver. J (new)
[   11.500649] cx88[0]: subsystem: 107d:6f38, board: UNKNOWN/GENERIC [card=0,autodetected]
[   11.500652] cx88[0]: TV tuner type -1, Radio tuner type -1
[   11.500805] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
[   11.505595] cx2388x alsa driver version 0.0.6 loaded
[   11.666381] tuner' 0-0061: chip found @ 0xc2 (cx88[0])
[   11.715441] cx88[0]/0: found at 0000:01:00.0, rev: 5, irq: 17, latency: 64, mmio: 0xdc000000
[   11.731597] cx88[0]/0: registered device video0 [v4l2]
[   11.731643] cx88[0]/0: registered device vbi0
[   11.731662] tuner' 0-0061: tuner type not setTakže ovladač je sice ve zdrojích jádra ale není donéj zaveden při startu! Dej sem Prosím výstup z:

Kód: [Vybrat]

lsmod | grep cx88Mělo by to být stejné jako u DTV2000H. Dřív sem míval DTV1000H a ten ovladač byl totožnej.
Néco zkusím ještě najít !

[jadd]

Zkus si nakopírovat tento firmwarehttp://mcentral.de/firmware/firmware_v5.tgz do "/lib/firmware"

Kód: [Vybrat]

tar -xzvf firmware_v5.tgz -C /lib/firmware/Restartuj a vlož sem zase výstupy z:

Kód: [Vybrat]

dmesg | grep cx tuner

[dredata_zizalka]

koukám, semnou to bude ještě těžký 

ten dmesg (ten pěkný začátek tam vůbec nemám...a bohužel nevím, jak ho vyvolat..

Kód: [Vybrat]

[    0.552549] PCI: 0000:00:1d.2 reg 20 io port: [8800, 881f]
[    0.552602] PCI: 0000:00:1d.3 reg 20 io port: [9000, 901f]
[    0.552659] PCI: 0000:00:1d.7 reg 10 32bit mmio: [dfcffc00, dfcfffff]
[    0.552723] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.552728] pci 0000:00:1d.7: PME# disabled
[    0.552856] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.552861] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.552896] PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
[    0.552903] PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
[    0.552910] PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
[    0.552917] PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
[    0.552924] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf]
[    0.552968] PCI: 0000:00:1f.2 reg 10 io port: [a800, a807]
[    0.552974] PCI: 0000:00:1f.2 reg 14 io port: [a400, a403]
[    0.552981] PCI: 0000:00:1f.2 reg 18 io port: [a000, a007]
[    0.552987] PCI: 0000:00:1f.2 reg 1c io port: [9800, 9803]
[    0.552994] PCI: 0000:00:1f.2 reg 20 io port: [9400, 940f]
[    0.553025] pci 0000:00:1f.2: PME# supported from D3hot
[    0.553030] pci 0000:00:1f.2: PME# disabled
[    0.553073] PCI: 0000:00:1f.3 reg 20 io port: [400, 41f]
[    0.553132] PCI: 0000:04:00.0 reg 10 64bit mmio: [e0000000, efffffff]
[    0.553142] PCI: 0000:04:00.0 reg 18 64bit mmio: [dffe0000, dffeffff]
[    0.553149] PCI: 0000:04:00.0 reg 20 io port: [e000, e0ff]
[    0.553159] PCI: 0000:04:00.0 reg 30 32bit mmio: [dffc0000, dffdffff]
[    0.553189] pci 0000:04:00.0: supports D1
[    0.553191] pci 0000:04:00.0: supports D2
[    0.553218] PCI: 0000:04:00.1 reg 10 64bit mmio: [dfffc000, dfffffff]
[    0.553268] pci 0000:04:00.1: supports D1
[    0.553270] pci 0000:04:00.1: supports D2
[    0.553313] PCI: bridge 0000:00:01.0 io port: [e000, efff]
[    0.553317] PCI: bridge 0000:00:01.0 32bit mmio: [dff00000, dfffffff]
[    0.553322] PCI: bridge 0000:00:01.0 64bit mmio pref: [e0000000, efffffff]
[    0.553366] PCI: bridge 0000:00:1c.0 io port: [d000, dfff]
[    0.553432] PCI: 0000:02:00.0 reg 10 io port: [c800, c8ff]
[    0.553456] PCI: 0000:02:00.0 reg 18 64bit mmio: [dfeff000, dfefffff]
[    0.553480] PCI: 0000:02:00.0 reg 30 32bit mmio: [dfee0000, dfeeffff]
[    0.553540] pci 0000:02:00.0: supports D1
[    0.553542] pci 0000:02:00.0: supports D2
[    0.553544] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.553550] pci 0000:02:00.0: PME# disabled
[    0.553588] PCI: bridge 0000:00:1c.3 io port: [c000, cfff]
[    0.553592] PCI: bridge 0000:00:1c.3 32bit mmio: [dfe00000, dfefffff]
[    0.553654] PCI: 0000:01:01.0 reg 20 io port: [b400, b41f]
[    0.553690] pci 0000:01:01.0: supports D1
[    0.553692] pci 0000:01:01.0: supports D2
[    0.553695] pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.553700] pci 0000:01:01.0: PME# disabled
[    0.553750] PCI: 0000:01:01.1 reg 20 io port: [b800, b81f]
[    0.553786] pci 0000:01:01.1: supports D1
[    0.553788] pci 0000:01:01.1: supports D2
[    0.553790] pci 0000:01:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.553795] pci 0000:01:01.1: PME# disabled
[    0.553825] PCI: 0000:01:01.2 reg 10 32bit mmio: [dfdffc00, dfdffcff]
[    0.556061] pci 0000:01:01.2: supports D1
[    0.556063] pci 0000:01:01.2: supports D2
[    0.556066] pci 0000:01:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.556070] pci 0000:01:01.2: PME# disabled
[    0.556121] pci 0000:00:1e.0: transparent bridge
[    0.556125] PCI: bridge 0000:00:1e.0 io port: [b000, bfff]
[    0.556129] PCI: bridge 0000:00:1e.0 32bit mmio: [dfd00000, dfdfffff]
[    0.556154] bus 00 -> node 0
[    0.556161] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.556435] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.556571] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[    0.556792] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.556926] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[    0.560180] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.560341] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.560500] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.560658] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.560816] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.560973] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.561131] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.561288] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.561364] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - FF, should be F2 [20080609]
[    0.561364] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.561364] pnp: PnP ACPI init
[    0.561364] ACPI: bus type pnp registered
[    0.568429] pnp: PnP ACPI: found 16 devices
[    0.568432] ACPI: ACPI bus type pnp unregistered
[    0.568436] PnPBIOS: Disabled by ACPI PNP
[    0.568457] PCI: Using ACPI for IRQ routing
[    0.576045] NET: Registered protocol family 8
[    0.576050] NET: Registered protocol family 20
[    0.576077] NetLabel: Initializing
[    0.576077] NetLabel:  domain hash size = 128
[    0.576077] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.576093] NetLabel:  unlabeled traffic allowed by default
[    0.576101] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.576110] hpet0: 3 64-bit timers, 14318180 Hz
[    0.578146] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.578150]    actual entries 65620
[    0.578253] AppArmor: AppArmor Filesystem Enabled
[    0.578276] ACPI: RTC can wake from S4
[    0.580047] Switched to high resolution mode on CPU 0
[    0.580476] Switched to high resolution mode on CPU 1
[    0.584083] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[    0.584103] system 00:08: ioport range 0x290-0x297 has been reserved
[    0.584114] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[    0.584119] system 00:09: ioport range 0x800-0x87f has been reserved
[    0.584124] system 00:09: ioport range 0x480-0x4bf has been reserved
[    0.584128] system 00:09: ioport range 0x900-0x91f has been reserved
[    0.584134] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.584139] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.584144] system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
[    0.584150] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[    0.584162] system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.584167] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.584179] system 00:0e: iomem range 0xf0000000-0xf3ffffff has been reserved
[    0.584190] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[    0.584195] system 00:0f: iomem range 0xc0000-0xdffff could not be reserved
[    0.584200] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[    0.584204] system 00:0f: iomem range 0x100000-0x3fffffff could not be reserved
[    0.619433] pci 0000:00:01.0: PCI bridge, secondary bus 0000:04
[    0.619437] pci 0000:00:01.0:   IO window: 0xe000-0xefff
[    0.619442] pci 0000:00:01.0:   MEM window: 0xdff00000-0xdfffffff
[    0.619445] pci 0000:00:01.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
[    0.619451] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
[    0.619455] pci 0000:00:1c.0:   IO window: 0xd000-0xdfff
[    0.619460] pci 0000:00:1c.0:   MEM window: disabled
[    0.619464] pci 0000:00:1c.0:   PREFETCH window: disabled
[    0.619471] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:02
[    0.619474] pci 0000:00:1c.3:   IO window: 0xc000-0xcfff
[    0.619480] pci 0000:00:1c.3:   MEM window: 0xdfe00000-0xdfefffff
[    0.619484] pci 0000:00:1c.3:   PREFETCH window: disabled
[    0.619491] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[    0.619494] pci 0000:00:1e.0:   IO window: 0xb000-0xbfff
[    0.619500] pci 0000:00:1e.0:   MEM window: 0xdfd00000-0xdfdfffff
[    0.619504] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.619521] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.619526] pci 0000:00:01.0: setting latency timer to 64
[    0.619534] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.619539] pci 0000:00:1c.0: setting latency timer to 64
[    0.619548] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.619552] pci 0000:00:1c.3: setting latency timer to 64
[    0.619560] pci 0000:00:1e.0: setting latency timer to 64
[    0.619564] bus: 00 index 0 io port: [0, ffff]
[    0.619566] bus: 00 index 1 mmio: [0, ffffffff]
[    0.619569] bus: 04 index 0 io port: [e000, efff]
[    0.619571] bus: 04 index 1 mmio: [dff00000, dfffffff]
[    0.619573] bus: 04 index 2 mmio: [e0000000, efffffff]
[    0.619576] bus: 04 index 3 mmio: [0, 0]
[    0.619578] bus: 03 index 0 io port: [d000, dfff]
[    0.619581] bus: 03 index 1 mmio: [0, 0]
[    0.619583] bus: 03 index 2 mmio: [0, 0]
[    0.619585] bus: 03 index 3 mmio: [0, 0]
[    0.619587] bus: 02 index 0 io port: [c000, cfff]
[    0.619589] bus: 02 index 1 mmio: [dfe00000, dfefffff]
[    0.619592] bus: 02 index 2 mmio: [0, 0]
[    0.619594] bus: 02 index 3 mmio: [0, 0]
[    0.619596] bus: 01 index 0 io port: [b000, bfff]
[    0.619598] bus: 01 index 1 mmio: [dfd00000, dfdfffff]
[    0.619601] bus: 01 index 2 mmio: [0, 0]
[    0.619603] bus: 01 index 3 io port: [0, ffff]
[    0.619605] bus: 01 index 4 mmio: [0, ffffffff]
[    0.619616] NET: Registered protocol family 2
[    0.632126] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.632430] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.632909] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.633258] TCP: Hash tables configured (established 131072 bind 65536)
[    0.633262] TCP reno registered
[    0.640194] NET: Registered protocol family 1
[    0.640355] checking if image is initramfs... it is
[    1.395638] Freeing initrd memory: 8014k freed
[    1.396911] audit: initializing netlink socket (disabled)
[    1.396938] type=2000 audit(1250934963.396:1): initialized
[    1.402440] highmem bounce pool size: 64 pages
[    1.402447] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.405088] VFS: Disk quotas dquot_6.5.1
[    1.405190] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.405300] msgmni has been set to 1761
[    1.405433] io scheduler noop registered
[    1.405437] io scheduler anticipatory registered
[    1.405439] io scheduler deadline registered
[    1.405453] io scheduler cfq registered (default)
[    1.405559] pci 0000:04:00.0: Boot video device
[    1.405721] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    1.405759] pcieport-driver 0000:00:01.0: found MSI capability
[    1.405792] pci_express 0000:00:01.0:pcie00: allocate port service
[    1.405894] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.405928] pcieport-driver 0000:00:1c.0: found MSI capability
[    1.405964] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.406008] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.406107] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[    1.406140] pcieport-driver 0000:00:1c.3: found MSI capability
[    1.406175] pci_express 0000:00:1c.3:pcie00: allocate port service
[    1.406526] isapnp: Scanning for PnP cards...
[    1.759501] isapnp: No Plug & Play device found
[    1.797575] hpet_resources: 0xfed00000 is busy
[    1.797662] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.797798] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.798707] 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.800744] brd: module loaded
[    1.800817] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    1.800955] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    1.800958] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    1.801411] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.804756] mice: PS/2 mouse device common for all mice
[    1.804901] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.804926] rtc0: alarms up to one month, hpet irqs
[    1.805075] EISA: Probing bus 0 at eisa.0
[    1.805103] Cannot allocate resource for EISA slot 8
[    1.805105] EISA: Detected 0 cards.
[    1.805109] cpuidle: using governor ladder
[    1.805112] cpuidle: using governor menu
[    1.805682] TCP cubic registered
[    1.805715] Using IPI No-Shortcut mode
[    1.805933] registered taskstats version 1
[    1.806069]   Magic number: 5:509:930
[    1.806120] tty ptyxf: hash matches
[    1.806188] rtc_cmos 00:03: setting system clock to 2009-08-22 09:56:05 UTC (1250934965)
[    1.806191] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.806193] EDD information not available.
[    1.806389] Freeing unused kernel memory: 428k freed
[    1.806431] Write protecting the kernel text: 2584k
[    1.806460] Write protecting the kernel read-only data: 940k
[    1.827760] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    1.992666] fuse init (API version 7.9)
[    2.056952] ACPI: SSDT 3FF9E0B0, 01C6 (r1    AMI   CPU1PM        1 INTL 20060113)
[    2.216112] processor ACPI0007:00: registered as cooling_device0
[    2.216118] ACPI: Processor [CPU1] (supports 8 throttling states)
[    2.216448] ACPI: SSDT 3FF9E280, 013A (r1    AMI   CPU2PM        1 INTL 20060113)
[    2.216894] processor ACPI0007:01: registered as cooling_device1
[    2.216900] ACPI: Processor [CPU2] (supports 8 throttling states)
[    2.536373] usbcore: registered new interface driver usbfs
[    2.536409] usbcore: registered new interface driver hub
[    2.554895] usbcore: registered new device driver usb
[    2.555715] Floppy drive(s): fd0 is 1.44M
[    2.575715] FDC 0 is a post-1991 82077
[    2.602802] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    2.602824] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    2.602847] r8169 0000:02:00.0: setting latency timer to 64
[    2.603254] eth0: RTL8168b/8111b at 0xf8852000, 00:17:31:6c:c4:e4, XID 38000000 IRQ 220
[    2.614339] No dock devices found.
[    2.630101] SCSI subsystem initialized
[    2.650480] USB Universal Host Controller Interface driver v3.0
[    2.653506] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    2.653516] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.653520] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.653577] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    2.653615] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00008000
[    2.653768] usb usb1: configuration #1 chosen from 1 choice
[    2.653799] hub 1-0:1.0: USB hub found
[    2.653807] hub 1-0:1.0: 2 ports detected
[    2.654008] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[    2.660360] libata version 3.00 loaded.
[    2.860852] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    2.860863] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.860868] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.860899] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.860934] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008400
[    2.861057] usb usb2: configuration #1 chosen from 1 choice
[    2.861088] hub 2-0:1.0: USB hub found
[    2.861096] hub 2-0:1.0: 2 ports detected
[    2.964825] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.964836] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.964840] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.964868] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    2.964901] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
[    2.965003] usb usb3: configuration #1 chosen from 1 choice
[    2.965033] hub 3-0:1.0: USB hub found
[    2.965041] hub 3-0:1.0: 2 ports detected
[    2.972602] usb 1-1: new full speed USB device using uhci_hcd and address 2
[    3.068313] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    3.068323] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    3.068328] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    3.068357] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    3.068391] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00009000
[    3.068490] usb usb4: configuration #1 chosen from 1 choice
[    3.068528] hub 4-0:1.0: USB hub found
[    3.068537] hub 4-0:1.0: 2 ports detected
[    3.139777] usb 1-1: configuration #1 chosen from 1 choice
[    3.172364] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    3.172379] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    3.172383] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.172413] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    3.176319] ehci_hcd 0000:00:1d.7: debug port 1
[    3.176325] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    3.176333] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdfcffc00
[    3.180232] uhci_hcd 0000:01:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[    3.180240] uhci_hcd 0000:01:01.0: UHCI Host Controller
[    3.180267] uhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 6
[    3.180297] uhci_hcd 0000:01:01.0: irq 21, io base 0x0000b400
[    3.180403] usb usb6: configuration #1 chosen from 1 choice
[    3.180436] hub 6-0:1.0: USB hub found
[    3.180443] hub 6-0:1.0: 2 ports detected
[    3.188559] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.376107] usb 1-1: USB disconnect, address 2
[    3.384822] usb usb5: configuration #1 chosen from 1 choice
[    3.384852] hub 5-0:1.0: USB hub found
[    3.384861] hub 5-0:1.0: 8 ports detected
[    3.385658] uhci_hcd 0000:01:01.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[    3.385668] uhci_hcd 0000:01:01.1: UHCI Host Controller
[    3.592288] uhci_hcd 0000:01:01.1: new USB bus registered, assigned bus number 7
[    3.592322] uhci_hcd 0000:01:01.1: irq 22, io base 0x0000b800
[    3.592421] usb usb7: configuration #1 chosen from 1 choice
[    3.592452] hub 7-0:1.0: USB hub found
[    3.592459] hub 7-0:1.0: 2 ports detected
[    3.616081] usb 6-1: new full speed USB device using uhci_hcd and address 2
[    3.801436] pata_acpi 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    3.801468] pata_acpi 0000:00:1f.1: setting latency timer to 64
[    3.801482] pata_acpi 0000:00:1f.1: PCI INT A disabled
[    3.801509] pata_acpi 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    3.801528] pata_acpi 0000:00:1f.2: setting latency timer to 64
[    3.801537] pata_acpi 0000:00:1f.2: PCI INT B disabled
[    3.801562] ehci_hcd 0000:01:01.2: PCI INT C -> GSI 23 (level, low) -> IRQ 23
[    3.801575] ehci_hcd 0000:01:01.2: EHCI Host Controller
[    3.801619] ehci_hcd 0000:01:01.2: new USB bus registered, assigned bus number 8
[    3.801666] ehci_hcd 0000:01:01.2: irq 23, io mem 0xdfdffc00
[    3.802027] usb 6-1: configuration #1 chosen from 1 choice
[    3.805360] usb 6-1: can't set config #1, error -71
[    3.812530] ehci_hcd 0000:01:01.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.812702] usb usb8: configuration #1 chosen from 1 choice
[    3.812737] hub 8-0:1.0: USB hub found
[    3.812746] hub 8-0:1.0: 4 ports detected
[    3.924053] usb 5-1: new high speed USB device using ehci_hcd and address 2
[    4.027124] ata_piix 0000:00:1f.1: version 2.12
[    4.027140] ata_piix 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    4.027187] ata_piix 0000:00:1f.1: setting latency timer to 64
[    4.027750] scsi0 : ata_piix
[    4.027865] scsi1 : ata_piix
[    4.029535] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    4.029539] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    4.060933] usb 5-1: configuration #1 chosen from 1 choice
[    4.061443] usb 6-1: USB disconnect, address 2
[    4.192414] ata1.00: ATAPI: Optiarc DVD RW AD-7200A, 1.09, max UDMA/66
[    4.208350] ata1.00: configured for UDMA/66
[    4.376632] scsi 0:0:0:0: CD-ROM            Optiarc  DVD RW AD-7200A  1.09 PQ: 0 ANSI: 5
[    4.376774] ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    4.376781] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    4.376837] ata_piix 0000:00:1f.2: setting latency timer to 64
[    4.376905] scsi2 : ata_piix
[    4.376983] scsi3 : ata_piix
[    4.377027] ata3: SATA max UDMA/133 cmd 0xa800 ctl 0xa400 bmdma 0x9400 irq 23
[    4.377030] ata4: SATA max UDMA/133 cmd 0xa000 ctl 0x9800 bmdma 0x9408 irq 23
[    4.428033] usb 8-1: new high speed USB device using ehci_hcd and address 2
[    4.546945] ata3.00: ATA-7: WDC WD1600AAJS-00PSA0, 05.06H05, max UDMA/133
[    4.546951] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.561081] ata3.00: configured for UDMA/133
[    4.565247] usb 8-1: configuration #1 chosen from 1 choice
[    4.632103] usbcore: registered new interface driver hiddev
[    4.726847] scsi 2:0:0:0: Direct-Access     ATA      WDC WD1600AAJS-0 05.0 PQ: 0 ANSI: 5
[    4.734682] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[    4.734722] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[    4.750489] Driver 'sr' needs updating - please use bus_type methods
[    4.755504] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.755510] Uniform CD-ROM driver Revision: 3.20
[    4.755619] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    4.769695] Driver 'sd' needs updating - please use bus_type methods
[    4.769823] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    4.769843] sd 2:0:0:0: [sda] Write Protect is off
[    4.769846] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.769876] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.769957] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    4.769975] sd 2:0:0:0: [sda] Write Protect is off
[    4.769977] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.770007] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.770011]  sda: sda1 sda2 sda3
[    4.799207] sd 2:0:0:0: [sda] Attached SCSI disk
[    4.872066] usb 7-1: new low speed USB device using uhci_hcd and address 2
[    5.048568] usb 7-1: configuration #1 chosen from 1 choice
[    5.071937] input: Leadtek WinFast DTV Dongle Gold as /devices/pci0000:00/0000:00:1e.0/0000:01:01.2/usb8/8-1/8-1:1.1/input/input2
[    5.072765] input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:01:01.2-1
[    5.095920] input: MLK Trust Mouse 15315-02 as /devices/pci0000:00/0000:00:1e.0/0000:01:01.1/usb7/7-1/7-1:1.0/input/input3
[    5.100990] input,hiddev96,hidraw1: USB HID v1.10 Mouse [MLK Trust Mouse 15315-02] on usb-0000:01:01.1-1
[    5.101030] usbcore: registered new interface driver usbhid
[    5.101036] usbhid: v2.6:USB HID core driver
[    5.139638] PM: Starting manual resume from disk
[    5.139642] PM: Resume from partition 8:3
[    5.139644] PM: Checking hibernation image.
[    5.139833] PM: Resume from disk failed.
[    5.181423] kjournald starting.  Commit interval 5 seconds
[    5.181441] EXT3-fs: mounted filesystem with ordered data mode.
[    9.907483] udevd version 124 started
[   10.256894] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   10.279356] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.398659] Linux agpgart interface v0.103
[   10.500726] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   10.520532] ACPI: Power Button (FF) [PWRF]
[   10.520720] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[   10.552521] ACPI: Power Button (CM) [PWRB]
[   10.916221] parport_pc 00:07: reported by Plug and Play ACPI
[   10.916327] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   10.973451] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   11.033495] [fglrx] Maximum main memory to use for locked dma buffers: 926 MBytes.
[   11.034035] [fglrx]   vendor: 1002 device: 95c5 count: 1
[   11.037427] [fglrx] ioport: bar 4, base 0xe000, size: 0x100
[   11.037443] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.037449] pci 0000:04:00.0: setting latency timer to 64
[   11.038473] [fglrx] PAT is enabled successfully!
[   11.038508] [fglrx] module loaded - fglrx 8.54.3 [Oct 10 2008] with 1 minors
[   11.380251] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[   11.380274] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   11.403302] intel_rng: FWH not detected
[   11.580840] iTCO_vendor_support: vendor-support=0
[   11.590406] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   11.617697] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   11.618706] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
[   11.618810] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   11.746523] HDA Intel 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   11.746551] HDA Intel 0000:04:00.1: setting latency timer to 64
[   11.760248] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[   11.893367] phy0: Selected rate control algorithm 'pid'
[   12.165915] zd1211rw 5-1:1.0: phy0
[   12.165951] usbcore: registered new interface driver zd1211rw
[   12.906127] lp0: using parport0 (interrupt-driven).
[   13.045890] Adding 1984016k swap on /dev/sda3.  Priority:-1 extents:1 across:1984016k
[   13.602734] EXT3 FS on sda2, internal journal
[   14.676898] type=1505 audit(1250927777.895:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4163
[   14.861905] type=1505 audit(1250927778.079:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4168
[   14.862125] type=1505 audit(1250927778.079:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4168
[   14.905640] type=1505 audit(1250927778.123:5): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=4172
[   15.082303] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.659100] ACPI: WMI: Mapper loaded
[   16.633173] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   18.715629] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   18.715638] apm: disabled - APM is not SMP safe.
[   19.067200] ppdev: user-space parallel port driver
[   20.754630] NET: Registered protocol family 10
[   20.756176] lo: Disabled Privacy Extensions
[   21.838609] Bluetooth: Core ver 2.13
[   21.839209] NET: Registered protocol family 31
[   21.839215] Bluetooth: HCI device and connection manager initialized
[   21.839220] Bluetooth: HCI socket layer initialized
[   21.884300] Bluetooth: L2CAP ver 2.11
[   21.884308] Bluetooth: L2CAP socket layer initialized
[   21.910719] Bluetooth: SCO (Voice Link) ver 0.6
[   21.910729] Bluetooth: SCO socket layer initialized
[   21.948389] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   21.948400] Bluetooth: BNEP filters: protocol multicast
[   21.996523] Bridge firewalling registered
[   22.024871] Bluetooth: RFCOMM socket layer initialized
[   22.025255] Bluetooth: RFCOMM TTY layer initialized
[   22.025265] Bluetooth: RFCOMM ver 1.10
[   25.117254] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[   25.117270] [fglrx] Reserved FB block: Unshared offset:ff73000, size:88000
[   25.117276] [fglrx] Reserved FB block: Unshared offset:fffc000, size:4000
[   26.149258] r8169: eth0: link down
[   26.149596] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.150743] firmware: requesting zd1211/zd1211b_ub
[   26.257440] firmware: requesting zd1211/zd1211b_uphr
[   26.326258] zd1211rw 5-1:1.0: firmware version 4725
[   26.366265] zd1211rw 5-1:1.0: zd1211b chip 0ace:1215 v4810 high 00-02-72 AL2230_RF pa0 g--NS
[   26.389329] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   26.515954] NET: Registered protocol family 17
[   60.345999] wlan0: authenticate with AP 00:12:0e:9b:e3:34
[   60.347511] wlan0: authenticated
[   60.347523] wlan0: associate with AP 00:12:0e:9b:e3:34
[   60.349884] wlan0: RX AssocResp from 00:12:0e:9b:e3:34 (capab=0x411 status=0 aid=1)
[   60.349893] wlan0: associated
[   60.350410] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   70.952015] wlan0: no IPv6 routers present
[  124.780388] ppdev0: registered pardevice
[  124.828284] ppdev0: unregistered pardevice
[  125.345275] ppdev0: registered pardevice
[  125.392257] ppdev0: unregistered pardevice
[  125.472119] ppdev0: registered pardevice
[  125.520027] ppdev0: unregistered pardevice
zizalka@zizalka-desktop:~$

lsmod

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ lsmod
Module                  Size  Used by
af_packet              25856  4
binfmt_misc            16904  1
rfcomm                 44432  0
bridge                 56980  0
stp                    10628  1 bridge
bnep                   20352  2
sco                    18308  2
l2cap                  30464  6 rfcomm,bnep
bluetooth              62180  6 rfcomm,bnep,sco,l2cap
ipv6                  264356  20
ppdev                  15748  0
acpi_cpufreq           15500  0
cpufreq_stats          13188  0
cpufreq_powersave       9856  0
cpufreq_ondemand       14988  2
freq_table             12672  3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_conservative    14600  0
cpufreq_userspace      11396  0
pci_slot               12680  0
container              11520  0
wmi                    14504  0
video                  25488  0
output                 11008  1 video
sbs                    19464  0
sbshc                  13440  1 sbs
battery                18436  0
iptable_filter         10752  0
ip_tables              19600  1 iptable_filter
x_tables               22916  1 ip_tables
ac                     12292  0
lp                     17156  0
arc4                    9984  2
ecb                    10880  2
crypto_blkcipher       25476  1 ecb
joydev                 18368  0
zd1211rw               53380  0
iTCO_wdt               18596  0
evdev                  17696  9
pcspkr                 10624  0
iTCO_vendor_support    11652  1 iTCO_wdt
mac80211              216948  1 zd1211rw
snd_hda_intel         385072  3
cfg80211               32520  1 mac80211
snd_pcm_oss            46848  0
snd_seq_dummy          10884  0
snd_mixer_oss          22784  1 snd_pcm_oss
snd_seq_oss            38528  0
snd_pcm                83204  2 snd_hda_intel,snd_pcm_oss
snd_seq_midi           14336  0
fglrx                1813832  31
parport_pc             39332  1
parport                42604  3 ppdev,lp,parport_pc
snd_rawmidi            29824  1 snd_seq_midi
snd_seq_midi_event     15232  2 snd_seq_oss,snd_seq_midi
snd_seq                57776  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer              29960  2 snd_pcm,snd_seq
snd_seq_device         15116  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd                    63396  15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
button                 14224  0
soundcore              15328  1 snd
intel_agp              33980  0
agpgart                42184  2 fglrx,intel_agp
snd_page_alloc         16136  2 snd_hda_intel,snd_pcm
shpchp                 38036  0
pci_hotplug            34976  1 shpchp
ext3                  133384  1
jbd                    55956  1 ext3
mbcache                16004  1 ext3
sd_mod                 42392  3
crc_t10dif              9984  1 sd_mod
sr_mod                 22212  0
cdrom                  43168  1 sr_mod
sg                     39732  0
usbhid                 35712  0
hid                    50560  1 usbhid
ata_piix               24708  2
ata_generic            12932  0
pata_acpi              12160  0
ehci_hcd               43788  0
uhci_hcd               30864  0
libata                178336  3 ata_piix,ata_generic,pata_acpi
scsi_mod              155468  4 sd_mod,sr_mod,sg,libata
dock                   16656  1 libata
r8169                  37764  0
mii                    13440  1 r8169
floppy                 64644  0
usbcore               149616  5 zd1211rw,usbhid,ehci_hcd,uhci_hcd
thermal                23708  0
processor              42156  2 acpi_cpufreq,thermal
fan                    12548  0
fbcon                  47648  0
tileblit               10880  1 fbcon
font                   16512  1 fbcon
bitblit                13824  1 fbcon
softcursor              9984  1 bitblit
fuse                   60956  3
zizalka@zizalka-desktop:~$

grep

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ grep cx88


ještě jsem zkusila, změnit tamtu cestu..soubor jsem is našla - je skutečně cz-Praha...

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ scan /usr/share/doc/dvb-utils/examples/scan/cz-Praha > /home/zizalka/achannels.conf
scanning /usr/share/doc/dvb-utils/examples/scan/cz-Praha
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory
zizalka@zizalka-desktop:~$
pokud to dobře chápu - odpovídá to:

Problém je ale v tom že ti chybí soubory zařízení v "/dev/dvb/".

nicméně jsem se zase zasekla... stáhla jsem si ten soubor a zkusila ho rozbalit ručně - nemám oprávnění a samozřejmě nevím jak si ho zapnout...v terminálu dám sudo, že? tam jsem to zkusila bez sudo i se sudo:

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ tar -xzvf firmware_v5.tgz -C /lib/firmware/
tar: firmware_v5.tgz: Nelze open: No such file or directory
tar: Z chyby se nelze zotavit: ukončuji se
tar: Child returned status 2
tar: Za běhu programu nastala chyba
zizalka@zizalka-desktop:~$
balík se mi stáhl na plochu...pokusím se najít někde co dělám špatně...

[jadd]

Musíš se prostě příkazem:

Kód: [Vybrat]

cd /home/zizalka/Desktop, dostat na plochu a použít

Kód: [Vybrat]

sudo tar -xzvf firmware_v5.tgz -C /lib/firmware/,
případně uvést celou cestu

Kód: [Vybrat]

sudo tar -xzvf /home/zizalka/Desktop/firmware_v5.tgz -C /lib/firmware/Další kroky přijdou !

[dredata_zizalka]

jipíí 

Kód: [Vybrat]

zizalka@zizalka-desktop:~/Plocha$ sudo tar -xzvf firmware_v5.tgz -C /lib/firmware/
firmware_spec2_dump0.i2c.fw
firmware_spec2_dump1.i2c.fw
firmware_spec2_dump2.i2c.fw
firmware_spec2_dump3.i2c.fw
firmware_spec2_dump4.i2c.fw
firmware_spec2_dump5.i2c.fw
firmware_spec2_dump6.i2c.fw
firmware_spec2_dump7.i2c.fw
firmware_spec2_dump8.i2c.fw
firmware_spec2_dump9.i2c.fw
firmware_spec2_dump10.i2c.fw
firmware_spec2_dump11.i2c.fw
firmware_spec2_dump12.i2c.fw
firmware_spec2_dump13.i2c.fw
firmware_spec2_dump14.i2c.fw
xc3028_8MHz_init0.i2c.fw
xc3028_8MHz_MTS_init0.i2c.fw
xc3028_BG_PAL_A2_A.i2c.fw
xc3028_BG_PAL_A2_A.i2c.fw.backup
xc3028_BG_PAL_A2_A_MTS.i2c.fw
xc3028_BG_PAL_A2_B.i2c.fw
xc3028_BG_PAL_A2_B_MTS.i2c.fw
xc3028_BG_PAL_NICAM_A.i2c.fw
xc3028_BG_PAL_NICAM_A_MTS.i2c.fw
xc3028_BG_PAL_NICAM_B.i2c.fw
xc3028_BG_PAL_NICAM_B_MTS.i2c.fw
xc3028_DK_PAL_A2.i2c.fw
xc3028_DK_PAL_A2_MTS.i2c.fw
xc3028_DK_PAL_NICAM.i2c.fw
xc3028_DK_PAL_NICAM_MTS.i2c.fw
xc3028_DK_SECAM_A2_DK1.i2c.fw
xc3028_DK_SECAM_A2_DK1_MTS.i2c.fw
xc3028_DK_SECAM_A2_L_DK3.i2c.fw
xc3028_DK_SECAM_A2_L_DK3_MTS.i2c.fw
xc3028_DTV6_ATSC_2620.i2c.fw
xc3028_DTV6_ATSC_2633.i2c.fw
xc3028_DTV6_QAM_2620.i2c.fw
xc3028_DTV6_QAM_2633.i2c.fw
xc3028_DTV7_2620.i2c.fw
xc3028_DTV7_2633.i2c.fw
xc3028_DTV8_2620.i2c.fw
xc3028_DTV8_2633.i2c.fw
xc3028_DTV78_2620.i2c.fw
xc3028_DTV78_2633.i2c.fw
xc3028_FM.i2c.fw
xc3028_FM_init0.i2c.fw
xc3028_FM_INPUT1_init0.i2c.fw
xc3028_init0.i2c.fw
xc3028_I_PAL_NICAM.i2c.fw
xc3028_I_PAL_NICAM_MTS.i2c.fw
xc3028_L_SECAM_AM.i2c.fw
xc3028_L_SECAM_NICAM.i2c.fw
xc3028_L'_SECAM_NICAM.i2c.fw
xc3028_MN_NTSCPAL_A2.i2c.fw
xc3028_MN_NTSCPAL_A2_LCD.i2c.fw
xc3028_MN_NTSCPAL_A2_LCD_NOGD.i2c.fw
xc3028_MN_NTSCPAL_A2_MTS.i2c.fw
xc3028_MN_NTSCPAL_BTSC.i2c.fw
xc3028_MN_NTSCPAL_BTSC_LCD.i2c.fw
xc3028_MN_NTSCPAL_BTSC_LCD_NOGD.i2c.fw
xc3028_MN_NTSCPAL_EIAJ.i2c.fw
xc3028_MN_NTSCPAL_EIAJ_LCD.i2c.fw
xc3028_MN_NTSCPAL_EIAJ_LCD_NOGD.i2c.fw
xc3028_MN_NTSCPAL_MTS.i2c.fw
xc3028_MN_NTSCPAL_MTS_LCD.i2c.fw
xc3028_MN_NTSCPAL_MTS_LCD_NOGD.i2c.fw
xc3028_MTS_init0.i2c.fw
zizalka@zizalka-desktop:~/Plocha$
napjatě poslouchám 

[jadd]

Nevím jestli budu dělat všechno správně ale vím že se musí zavést modul do jádra.
Měla by si mít nainstalován balík "kernel-headers" ale to které přísluší tvému jádru viz. http://wiki.ubuntu.cz/Kompilace%20kernelu
Dál si musíš najít v jádře soubor začínající "cx" a končící na ".ko" až ho budeš mít dej sem výstup

Kód: [Vybrat]

ls /adresář_kde_jsou_ty_soubory(moduly)

[dredata_zizalka]

popravdě kernel-headers mám nasinstalvoaný (neptej se mě kdy jak a proč tolik  ) v adresáři mám tyhle složky:
linux-headers-2.6-27-7, linux-headers-2.6-27-7-generic, linux-headers-2.6.27-14, linux-headers-2.6.27.14 generic
přesně tohle se mi nabízí když se mi startuje ubuntu + windows. Nechávám to na poslední možnosti...takže budu hledat v té poslední složce
při hledání všeho, obsahujícího cx mi vyjede několik souborů a složek, ale nic co by končilo .ko

ani v ostatních složkách něco takového není..a jelikož jsem často mimo...nechala jsem to hledat v celém systému souborů...

našla jsem znovu linux-header (2 složky, ty s tím generic), pokud budu brát zase v potaz to v "čem startuju ubuntu"
tak je tam těch souborů víc  cx88xx.ko apod... :-) takže je asi vezmu postupně...snad se mi pak počítač nezblázní

no tak jsem si ke všemu našla cestu  ale pokud zadám ten příkaz, tak se to jen opíše a nic víc... kdepak zase dělám chybu? 

posílám to co jsem si zkopírovala do wordu (či jak se to jmenuje  )

Kód: [Vybrat]

ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx18/cx18.ko

zizalka@zizalka-desktop:~$ ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx18/cx18.ko

/lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx18/cx18.ko


ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx2341x.ko/

zizalka@zizalka-desktop:~$ ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx2341x.ko

/lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx2341x.ko



další ozkoušené – výsledek pořád stejný

ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-blackbird.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-dvb.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-vp3054-i2c.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88xx.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx8800.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx8802.ko


ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx23885/cx23885.ko

ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/dvb/frontends/cx22700.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/dvb/frontends/cx22702.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/dvb/frontends/cx24110.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/dvb/frontends/cx24123.ko

ls /lib/modules/2.6.27-14-generic/kernel/drivers/usb/atm/cxacru.ko

ls /lib/modules/2.6.27-14-generic/kernel/drivers/net/chelsio/cxgb.ko
ls /lib/modules/2.6.27-14-generic/kernel/drivers/net/cxgb3/cxgb3.ko




[jadd]

Já sem taky nechtěl nic jiného než vidět ty soubory a ne jenom adresář. 

[dredata_zizalka]

no já jsem lama - nechápu 

já když zadám to terminálu ls.... tka mi to vůbec nic nevypíše:

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko
/lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko
zizalka@zizalka-desktop:~$

zkoušela jsem to uvšech a u všech mi to nic nepíše...tak nevím

když to zkusím bez ls:

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko
bash: /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko: Permission denied
zizalka@zizalka-desktop:~$ sudo /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko
[sudo] password for zizalka:
sudo: /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/cx88-alsa.ko: command not found
zizalka@zizalka-desktop:~$

já se omlouvám, ale momentálně fakt netuším co potřebujete 

[jadd]

Kód: [Vybrat]

ls /lib/modules/2.6.27-14-generic/kernel/drivers/media/video/cx88/Chtěl jsem vidét jen ty soubory ".ko" nebyl jsem totiž připojen v linuxu už je vidím:

Kód: [Vybrat]

daja51@daja51NB:~$ ls /lib/modules/2.6.28-13-generic/kernel/drivers/media/video/cx88/
cx88-alsa.ko       cx88-dvb.ko         cx88xx.ko  cx8802.ko
cx88-blackbird.ko  cx88-vp3054-i2c.ko  cx8800.ko
Ale než to budem muset zavádět. raději bych instaloval nové jaderné balíky:
"linux-image-2.6.28-15-generic", "linux-restricted-modules-2.6.28-15-generic", "linux-firmware"
Když máš problém s hardwarem je nejjednoduší zkusit aktualizované jádro.

[dredata_zizalka]

linux-firmware mám naistalovaný
synaptic mám aktualizovaný...ale ty další dva balíky tam nejsou...jen starší... 

kouknu jestli je ještě najdu někde na netu...

bude mi to fungovat, když mám ubuntu 8.10? našla jsem nějaké (pro mě varovné) informace:

Ubuntu 8.10: linux-image-2.6.27-14-generic 2.6.27-14.39 linux-image-2.6.27-14-server 2.6.27-14.39 linux-image-2.6.27-14-virtual 2.6.27-14.39
Ubuntu 9.04: linux-image-2.6.28-15-generic 2.6.28-15.49

http://www.ubuntu.com/usn/usn-819-1

aby mi se mi to tu celé nezaseklo?? 

[jadd]

Tak jenom poslední pro Intrepid(8.04)
Jinak pošli

Kód: [Vybrat]

cat /etc/apt/sources.list

[dredata_zizalka]

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ cat /etc/apt/sources.list
# deb cdrom:[Ubuntu 8.10 _Intrepid Ibex_ - Release i386 (20081029.5)]/ intrepid main restricted
# See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to
# newer versions of the distribution.

deb http://cz.archive.ubuntu.com/ubuntu/ intrepid main restricted
deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid main restricted

## Major bug fix updates produced after the final release of the
## distribution.
deb http://cz.archive.ubuntu.com/ubuntu/ intrepid-updates main restricted
deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid-updates main restricted



## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu
## team. Also, please note that software in universe WILL NOT receive any
## review or updates from the Ubuntu security team.
deb http://cz.archive.ubuntu.com/ubuntu/ intrepid universe
deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid universe
deb http://cz.archive.ubuntu.com/ubuntu/ intrepid-updates universe
deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid-updates universe

## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu
## team, and may not be under a free licence. Please satisfy yourself as to
## your rights to use the software. Also, please note that software in
## multiverse WILL NOT receive any review or updates from the Ubuntu
## security team.
deb http://cz.archive.ubuntu.com/ubuntu/ intrepid multiverse
deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid multiverse
deb http://cz.archive.ubuntu.com/ubuntu/ intrepid-updates multiverse
deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid-updates multiverse

## Uncomment the following two lines to add software from the 'backports'
## repository.
## N.B. software from this repository may not have been tested as
## extensively as that contained in the main release, although it includes
## newer versions of some applications which may provide useful features.
## Also, please note that software in backports WILL NOT receive any review
## or updates from the Ubuntu security team.
# deb http://cz.archive.ubuntu.com/ubuntu/ intrepid-backports main restricted universe multiverse
# deb-src http://cz.archive.ubuntu.com/ubuntu/ intrepid-backports main restricted universe multiverse

## Uncomment the following two lines to add software from Canonical's
## 'partner' repository. This software is not part of Ubuntu, but is
## offered by Canonical and the respective vendors as a service to Ubuntu
## users.
deb http://archive.canonical.com/ubuntu intrepid partner
# deb-src http://archive.canonical.com/ubuntu intrepid partner

deb http://security.ubuntu.com/ubuntu intrepid-security main restricted
deb-src http://security.ubuntu.com/ubuntu intrepid-security main restricted
deb http://security.ubuntu.com/ubuntu intrepid-security universe
deb-src http://security.ubuntu.com/ubuntu intrepid-security universe
deb http://security.ubuntu.com/ubuntu intrepid-security multiverse
deb-src http://security.ubuntu.com/ubuntu intrepid-security multiverse
deb http://packages.medibuntu.org/ intrepid free non-free #Medibuntu pro Ubuntu 8.10
zizalka@zizalka-desktop:~$

naistalované mám:
linux-image-2.6.27-14-generic - Linux kernel image for version 2.6.27 on x86/x86_64
linux-image-2.6.27-7-generic
linux-image-generic
linux-generic
linux-headers-generic
 linux-restricted-modules-generic
linux-restricted-modules-2.6.27-14-generic
linux-restricted-modules-2.6.27-7-generic

bohužel opět nerozumím, poslední k 8.04 bude starší než to co mám teď k 8.10 ne? 
já sem asi natvrdlá...

[jadd]

A když restartuješ a vložíš tvkartu, máš v /dev/dvb/ (frontend0 atd...)?

bohužel opět nerozumím, poslední k 8.04 bude starší než to co mám teď k 8.10 ne?  Jsem v rozpacích
já sem asi natvrdlá...

To sem zkopal já! Sám se pořád učím.

[dredata_zizalka]

no když nechám hledat v celém disku souborů frontend0 tak mi to nic nenajde, at s adaptérem nebo bez něj... frontend by bylo ale ne frontend0
dev tu mám taky dost, ale žádjé neobsahuje dvb
zkusila jsme tamten příkaz:

Kód: [Vybrat]

zizalka@zizalka-desktop:~$ scan /usr/share/doc/dvb-utils/examples/scan/cz-Praha > /home/zizalka/achannels.conf
scanning /usr/share/doc/dvb-utils/examples/scan/cz-Praha
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory
zizalka@zizalka-desktop:~$


[jadd]

Máš ve svém systému v /etc... , sobor modules.conf nebo modprobe.conf já totiž ne !

[dredata_zizalka]

našla jsem modules - obsahuej text:

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

fuse
lp

to druhé nemám nechala jsem prohledat celý disk
edit!!!

našla jsem ale soubor je prázdný..a nejsem si jistá jestli je conf a to ani u tamtoho...

[jadd]

To mám taky ale bez obsahu "fuse" a to sem ani nemyslel myslel jsem s koncovkou ".conf"
Já totiž svou kartu "AVerTV Hybrid Volar HX" zprovoznil jednoduše spuštěním skriptu přímo od výrobce.
No nic vyzkoušej tyto příkazy jestli něco udělaj (měli by zavést modul do jádra):

Kód: [Vybrat]

sudo modprobe cx8800

Kód: [Vybrat]

sudo modprobe cx88xx

Kód: [Vybrat]

sudo modprobe cx88-dvb

Kód: [Vybrat]

sudo modprobe cx88-alsaUdělá to něco ?