Nízká obnovovací frekvence monitoru

[Lucky-V]

Dobrý den,

rád bych Vás poprosil o pomoc s mým problémem. Jsem majitelem notebooku Acer Aspire 3810TZ. Po instalaci Ubuntu 10.10 jsem zjistil, že obnovovací frekvence na mém monitoru zcela jistě není 60Hz (když stáhnu podsvícení, je vidět jak monitor bliká, při plném podsvícení to tolik vidět není, nicméně oči tím znatelně trpí - bolí), ačkoliv v nastavení monitoru je tato hodnota nastavena (není tam na výběr ani žádná jiná).

Zkoušel jsem tuto frekvenci nastavit i v doinstalovaném správci compizu, ale neúspěšně (ať jsem zkusil nastavit obnovovací frekvenci na 10 Hz nebo na 100 Hz, chování monitoru se nijak nezměnilo - monitor si blikal pořád stejně). Podle jiného návodu jsem ještě zkoušel ručně nastavit do souboru /etc/X11/xorg.conf (který jsem musel ručně vytvořit) hodnoty rozlišení a obnovovací frekvence, dle výstupu z příkazu: gtf 1366 768 60.0. Tento postup bohužel také nezabral. Soubor xorg.conf jsem proto opět zrušil

Při zkoumání tohoto problému jsem narazil také na problém, že příkaz glxgears mi ukazuje hodnoty FPS kolem 59 FPS. Nicméně výstup příkazu glxinfo | grep direct mi říká, že podpora přímého vykreslování existuje. Grafická karta, kterou můj notebook obsahuje je Intel GMA 4500MHD.

Pokud by někoho napadlo něco, čím by to mohlo být, tak bych moc ocenil, kdyby mi pomohl. Pro úplnost zasílám výstup příkazu grep WW /var/log/Xorg.0.log a ještě kompletní výpis souboru /var/log/Xorg.0.log

Kód: [Vybrat]

lucky@lucky-Aspire-3810TZ:~$ grep WW /var/log/Xorg.0.log
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    27.557] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    28.443] (WW) Falling back to old probe method for vesa
[    28.443] (WW) Falling back to old probe method for fbdev
[    31.030] (WW) MLK Trust Mouse: ignoring absolute axes.


Kód: [Vybrat]

[    26.618]
X.Org X Server 1.9.0
Release Date: 2010-08-20
[    26.618] X Protocol Version 11, Revision 0
[    26.618] Build Operating System: Linux 2.6.24-27-server x86_64 Ubuntu
[    26.618] Current Operating System: Linux lucky-Aspire-3810TZ 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:32:27 UTC 2010 x86_64
[    26.618] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic root=UUID=10826288-9456-4288-a24e-5cc2d1e0f694 ro quiet splash
[    26.618] Build Date: 16 September 2010  06:18:41PM
[    26.618] xorg-server 2:1.9.0-0ubuntu7 (For technical support please see http://www.ubuntu.com/support)
[    26.618] Current version of pixman: 0.18.4
[    26.618] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[    26.618] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    26.619] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Nov  3 19:49:15 2010
[    26.790] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    27.485] (==) No Layout section.  Using the first Screen section.
[    27.485] (==) No screen section available. Using defaults.
[    27.485] (**) |-->Screen "Default Screen Section" (0)
[    27.485] (**) |   |-->Monitor "<default monitor>"
[    27.510] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[    27.510] (==) Automatically adding devices
[    27.510] (==) Automatically enabling devices
[    27.557] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    27.557] Entry deleted from font path.
[    27.801] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
[    27.801] (==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[    27.801] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[    27.801] (II) Loader magic: 0x7d0200
[    27.801] (II) Module ABI versions:
[    27.801] X.Org ANSI C Emulation: 0.4
[    27.801] X.Org Video Driver: 8.0
[    27.801] X.Org XInput driver : 11.0
[    27.801] X.Org Server Extension : 4.0
[    27.802] (--) PCI:*(0:0:2:0) 8086:2a42:1025:0229 rev 7, Mem @ 0xe0000000/4194304, 0xd0000000/268435456, I/O @ 0x00003110/8
[    27.802] (--) PCI: (0:0:2:1) 8086:2a43:1025:0229 rev 7, Mem @ 0xe2400000/1048576
[    27.802] (II) Open ACPI successful (/var/run/acpid.socket)
[    27.802] (II) LoadModule: "extmod"
[    27.820] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[    27.899] (II) Module extmod: vendor="X.Org Foundation"
[    27.899] compiled for 1.9.0, module version = 1.0.0
[    27.899] Module class: X.Org Server Extension
[    27.899] ABI class: X.Org Server Extension, version 4.0
[    27.899] (II) Loading extension MIT-SCREEN-SAVER
[    27.899] (II) Loading extension XFree86-VidModeExtension
[    27.899] (II) Loading extension XFree86-DGA
[    27.899] (II) Loading extension DPMS
[    27.899] (II) Loading extension XVideo
[    27.899] (II) Loading extension XVideo-MotionCompensation
[    27.899] (II) Loading extension X-Resource
[    27.899] (II) LoadModule: "dbe"
[    27.900] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[    28.070] (II) Module dbe: vendor="X.Org Foundation"
[    28.070] compiled for 1.9.0, module version = 1.0.0
[    28.070] Module class: X.Org Server Extension
[    28.070] ABI class: X.Org Server Extension, version 4.0
[    28.070] (II) Loading extension DOUBLE-BUFFER
[    28.070] (II) LoadModule: "glx"
[    28.071] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    28.092] (II) Module glx: vendor="X.Org Foundation"
[    28.110] compiled for 1.9.0, module version = 1.0.0
[    28.110] ABI class: X.Org Server Extension, version 4.0
[    28.110] (==) AIGLX enabled
[    28.110] (II) Loading extension GLX
[    28.145] (II) LoadModule: "record"
[    28.145] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    28.149] (II) Module record: vendor="X.Org Foundation"
[    28.149] compiled for 1.9.0, module version = 1.13.0
[    28.149] Module class: X.Org Server Extension
[    28.149] ABI class: X.Org Server Extension, version 4.0
[    28.149] (II) Loading extension RECORD
[    28.149] (II) LoadModule: "dri"
[    28.150] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    28.151] (II) Module dri: vendor="X.Org Foundation"
[    28.151] compiled for 1.9.0, module version = 1.0.0
[    28.151] ABI class: X.Org Server Extension, version 4.0
[    28.151] (II) Loading extension XFree86-DRI
[    28.151] (II) LoadModule: "dri2"
[    28.152] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    28.152] (II) Module dri2: vendor="X.Org Foundation"
[    28.153] compiled for 1.9.0, module version = 1.2.0
[    28.153] ABI class: X.Org Server Extension, version 4.0
[    28.153] (II) Loading extension DRI2
[    28.153] (==) Matched intel as autoconfigured driver 0
[    28.153] (==) Matched vesa as autoconfigured driver 1
[    28.153] (==) Matched fbdev as autoconfigured driver 2
[    28.153] (==) Assigned the driver to the xf86ConfigLayout
[    28.153] (II) LoadModule: "intel"
[    28.153] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    28.217] (II) Module intel: vendor="X.Org Foundation"
[    28.217] compiled for 1.9.0, module version = 2.12.0
[    28.217] Module class: X.Org Video Driver
[    28.217] ABI class: X.Org Video Driver, version 8.0
[    28.217] (II) LoadModule: "vesa"
[    28.217] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    28.228] (II) Module vesa: vendor="X.Org Foundation"
[    28.228] compiled for 1.8.99.905, module version = 2.3.0
[    28.228] Module class: X.Org Video Driver
[    28.228] ABI class: X.Org Video Driver, version 8.0
[    28.228] (II) LoadModule: "fbdev"
[    28.228] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    28.442] (II) Module fbdev: vendor="X.Org Foundation"
[    28.442] compiled for 1.8.99.905, module version = 0.4.2
[    28.442] ABI class: X.Org Video Driver, version 8.0
[    28.442] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge, Sandybridge, Sandybridge, Sandybridge, Sandybridge,
Sandybridge, Sandybridge
[    28.443] (II) VESA: driver for VESA chipsets: vesa
[    28.443] (II) FBDEV: driver for framebuffer: fbdev
[    28.443] (++) using VT number 7

[    28.443] (WW) Falling back to old probe method for vesa
[    28.443] (WW) Falling back to old probe method for fbdev
[    28.443] (II) Loading sub module "fbdevhw"
[    28.443] (II) LoadModule: "fbdevhw"
[    28.444] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    28.468] (II) Module fbdevhw: vendor="X.Org Foundation"
[    28.468] compiled for 1.9.0, module version = 0.0.2
[    28.468] ABI class: X.Org Video Driver, version 8.0
[    28.471] drmOpenDevice: node name is /dev/dri/card0
[    28.471] drmOpenDevice: open result is 9, (OK)
[    28.471] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[    28.471] drmOpenDevice: node name is /dev/dri/card0
[    28.471] drmOpenDevice: open result is 9, (OK)
[    28.471] drmOpenByBusid: drmOpenMinor returns 9
[    28.471] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[    28.471] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[    28.471] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    28.471] (==) intel(0): RGB weight 888
[    28.471] (==) intel(0): Default visual is TrueColor
[    28.471] (II) intel(0): Integrated Graphics Chipset: Intel(R) GM45
[    28.471] (--) intel(0): Chipset: "GM45"
[    28.471] (==) intel(0): video overlay key set to 0x101fe
[    28.510] (II) intel(0): Output VGA1 has no monitor section
[    28.510] (II) intel(0): Output LVDS1 has no monitor section
[    28.510] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
[    28.519] (II) intel(0): Output HDMI1 has no monitor section
[    28.519] (II) intel(0): Output DP1 has no monitor section
[    28.524] (II) intel(0): Output DP2 has no monitor section
[    28.940] (II) intel(0): Output TV1 has no monitor section
[    28.981] (II) intel(0): EDID for output VGA1
[    29.013] (II) intel(0): EDID for output LVDS1
[    29.013] (II) intel(0): Manufacturer: LGD  Model: 1f7  Serial#: 0
[    29.013] (II) intel(0): Year: 2009  Week: 0
[    29.013] (II) intel(0): EDID Version: 1.3
[    29.013] (II) intel(0): Digital Display Input
[    29.013] (II) intel(0): Max Image Size [cm]: horiz.: 29  vert.: 16
[    29.013] (II) intel(0): Gamma: 2.20
[    29.013] (II) intel(0): No DPMS capabilities specified
[    29.013] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[    29.013] (II) intel(0): First detailed timing is preferred mode
[    29.013] (II) intel(0): redX: 0.585 redY: 0.350   greenX: 0.335 greenY: 0.545
[    29.013] (II) intel(0): blueX: 0.160 blueY: 0.135   whiteX: 0.313 whiteY: 0.329
[    29.013] (II) intel(0): Manufacturer's mask: 0
[    29.013] (II) intel(0): Supported detailed timing:
[    29.013] (II) intel(0): clock: 72.3 MHz   Image Size:  293 x 165 mm
[    29.013] (II) intel(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    29.013] (II) intel(0): v_active: 768  v_sync: 771  v_sync_end 776 v_blanking: 790 v_border: 0
[    29.013] (II) intel(0):  
[    29.013] (II) intel(0):  LP133WH2-TLA3
[    29.013] (II) intel(0): EDID (in hex):
[    29.013] (II) intel(0): 00ffffffffffff0030e4f70100000000
[    29.013] (II) intel(0): 00130103801d10780aee259559558b29
[    29.013] (II) intel(0): 22505400000001010101010101010101
[    29.013] (II) intel(0): 0101010101013e1c56a0500016303020
[    29.013] (II) intel(0): 350025a5100000190000000000000000
[    29.013] (II) intel(0): 00000000000000000000000000fe0000
[    29.013] (II) intel(0): 00004c47446973706c61790a000000fe
[    29.013] (II) intel(0): 004c503133335748322d544c413300c2
[    29.013] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[    29.013] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[    29.014] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[    29.014] (II) intel(0): Printing probed modes for output LVDS1
[    29.014] (II) intel(0): Modeline "1366x768"x60.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    29.014] (II) intel(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz)
[    29.014] (II) intel(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz)
[    29.014] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[    29.014] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[    29.014] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
[    29.014] (II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
[    29.023] (II) intel(0): EDID for output HDMI1
[    29.023] (II) intel(0): EDID for output DP1
[    29.028] (II) intel(0): EDID for output DP2
[    29.440] (II) intel(0): EDID for output TV1
[    29.440] (II) intel(0): Output VGA1 disconnected
[    29.440] (II) intel(0): Output LVDS1 connected
[    29.440] (II) intel(0): Output HDMI1 disconnected
[    29.440] (II) intel(0): Output DP1 disconnected
[    29.440] (II) intel(0): Output DP2 disconnected
[    29.440] (II) intel(0): Output TV1 disconnected
[    29.441] (II) intel(0): Using exact sizes for initial modes
[    29.441] (II) intel(0): Output LVDS1 using initial mode 1366x768
[    29.441] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    29.441] (II) intel(0): Kernel page flipping support detected, but forcibly disabled.
[    29.441] (==) intel(0): DPI set to (96, 96)
[    29.441] (II) Loading sub module "fb"
[    29.441] (II) LoadModule: "fb"
[    29.441] (II) Loading /usr/lib/xorg/modules/libfb.so
[    29.478] (II) Module fb: vendor="X.Org Foundation"
[    29.478] compiled for 1.9.0, module version = 1.0.0
[    29.478] ABI class: X.Org ANSI C Emulation, version 0.4
[    29.478] (II) UnloadModule: "vesa"
[    29.479] (II) Unloading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    29.479] (II) UnloadModule: "fbdev"
[    29.479] (II) Unloading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    29.479] (II) UnloadModule: "fbdevhw"
[    29.479] (II) Unloading /usr/lib/xorg/modules/libfbdevhw.so
[    29.479] (==) Depth 24 pixmap format is 32 bpp
[    29.479] (II) intel(0): [DRI2] Setup complete
[    29.479] (II) intel(0): [DRI2]   DRI driver: i965
[    29.479] (**) intel(0): Tiling enabled
[    29.479] (**) intel(0): SwapBuffers wait enabled
[    29.479] (==) intel(0): VideoRam: 262144 KB
[    29.479] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[    29.526] (II) UXA(0): Driver registered support for the following operations:
[    29.526] (II)         solid
[    29.526] (II)         copy
[    29.526] (II)         composite (RENDER acceleration)
[    29.526] (II)         put_image
[    29.526] (II)         get_image
[    29.526] (==) intel(0): Backing store disabled
[    29.526] (==) intel(0): Silken mouse enabled
[    29.527] (II) intel(0): Initializing HW Cursor
[    29.561] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    29.563] (==) intel(0): DPMS enabled
[    29.563] (==) intel(0): Intel XvMC decoder enabled
[    29.563] (II) intel(0): Set up textured video
[    29.564] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[    29.564] (II) intel(0): direct rendering: DRI2 Enabled
[    29.564] (--) RandR disabled
[    29.564] (II) Initializing built-in extension Generic Event Extension
[    29.564] (II) Initializing built-in extension SHAPE
[    29.564] (II) Initializing built-in extension MIT-SHM
[    29.564] (II) Initializing built-in extension XInputExtension
[    29.564] (II) Initializing built-in extension XTEST
[    29.564] (II) Initializing built-in extension BIG-REQUESTS
[    29.564] (II) Initializing built-in extension SYNC
[    29.564] (II) Initializing built-in extension XKEYBOARD
[    29.564] (II) Initializing built-in extension XC-MISC
[    29.564] (II) Initializing built-in extension SECURITY
[    29.564] (II) Initializing built-in extension XINERAMA
[    29.564] (II) Initializing built-in extension XFIXES
[    29.564] (II) Initializing built-in extension RENDER
[    29.564] (II) Initializing built-in extension RANDR
[    29.564] (II) Initializing built-in extension COMPOSITE
[    29.564] (II) Initializing built-in extension DAMAGE
[    29.564] (II) Initializing built-in extension GESTURE
[    29.776] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    29.776] (II) AIGLX: enabled GLX_INTEL_swap_event
[    29.776] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    29.776] (II) AIGLX: enabled GLX_SGI_make_current_read
[    29.776] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    29.776] (II) AIGLX: Loaded and initialized /usr/lib/dri/i965_dri.so
[    29.776] (II) GLX: Initialized DRI2 GL provider for screen 0
[    29.776] (II) intel(0): Setting screen physical size to 361 x 203
[    30.097] (II) XKB: generating xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[    30.661] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    30.661] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    30.661] (II) LoadModule: "evdev"
[    30.662] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    30.738] (II) Module evdev: vendor="X.Org Foundation"
[    30.738] compiled for 1.9.0, module version = 2.3.2
[    30.738] Module class: X.Org XInput Driver
[    30.738] ABI class: X.Org XInput driver, version 11.0
[    30.738] (**) Power Button: always reports core events
[    30.738] (**) Power Button: Device: "/dev/input/event3"
[    30.780] (II) Power Button: Found keys
[    30.780] (II) Power Button: Configuring as keyboard
[    30.780] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    30.780] (**) Option "xkb_rules" "evdev"
[    30.780] (**) Option "xkb_model" "evdev"
[    30.780] (**) Option "xkb_layout" "cz"
[    30.783] (II) XKB: generating xkmfile /var/lib/xkb/server-A54AEDFEFDBEDDA8B4D3BCC5AF2299BD6BD0DEB7.xkm
[    30.847] (II) config/udev: Adding input device Video Bus (/dev/input/event8)
[    30.847] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    30.847] (**) Video Bus: always reports core events
[    30.847] (**) Video Bus: Device: "/dev/input/event8"
[    30.871] (II) Video Bus: Found keys
[    30.871] (II) Video Bus: Configuring as keyboard
[    30.871] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[    30.871] (**) Option "xkb_rules" "evdev"
[    30.871] (**) Option "xkb_model" "evdev"
[    30.871] (**) Option "xkb_layout" "cz"
[    30.875] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    30.875] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    30.875] (**) Power Button: always reports core events
[    30.875] (**) Power Button: Device: "/dev/input/event0"
[    30.931] (II) Power Button: Found keys
[    30.931] (II) Power Button: Configuring as keyboard
[    30.931] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    30.931] (**) Option "xkb_rules" "evdev"
[    30.931] (**) Option "xkb_model" "evdev"
[    30.931] (**) Option "xkb_layout" "cz"
[    30.932] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[    30.932] (II) No input driver/identifier specified (ignoring)
[    30.932] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[    30.932] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[    30.932] (**) Sleep Button: always reports core events
[    30.932] (**) Sleep Button: Device: "/dev/input/event2"
[    30.960] (II) Sleep Button: Found keys
[    30.960] (II) Sleep Button: Configuring as keyboard
[    30.960] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
[    30.960] (**) Option "xkb_rules" "evdev"
[    30.960] (**) Option "xkb_model" "evdev"
[    30.960] (**) Option "xkb_layout" "cz"
[    30.962] (II) config/udev: Adding input device HD Video WebCam (/dev/input/event6)
[    30.962] (**) HD Video WebCam: Applying InputClass "evdev keyboard catchall"
[    30.962] (**) HD Video WebCam: always reports core events
[    30.962] (**) HD Video WebCam: Device: "/dev/input/event6"
[    30.990] (II) HD Video WebCam: Found keys
[    30.990] (II) HD Video WebCam: Configuring as keyboard
[    30.990] (II) XINPUT: Adding extended input device "HD Video WebCam" (type: KEYBOARD)
[    30.990] (**) Option "xkb_rules" "evdev"
[    30.990] (**) Option "xkb_model" "evdev"
[    30.990] (**) Option "xkb_layout" "cz"
[    30.993] (II) config/udev: Adding input device MLK Trust Mouse (/dev/input/event5)
[    30.993] (**) MLK Trust Mouse: Applying InputClass "evdev pointer catchall"
[    30.993] (**) MLK Trust Mouse: Applying InputClass "evdev keyboard catchall"
[    30.993] (**) MLK Trust Mouse: always reports core events
[    30.993] (**) MLK Trust Mouse: Device: "/dev/input/event5"
[    31.030] (II) MLK Trust Mouse: Found 9 mouse buttons
[    31.030] (II) MLK Trust Mouse: Found scroll wheel(s)
[    31.030] (II) MLK Trust Mouse: Found relative axes
[    31.030] (II) MLK Trust Mouse: Found x and y relative axes
[    31.030] (II) MLK Trust Mouse: Found absolute axes
[    31.030] (II) evdev-grail: failed to open grail, no gesture support
[    31.030] (II) MLK Trust Mouse: Found keys
[    31.030] (II) MLK Trust Mouse: Configuring as mouse
[    31.030] (II) MLK Trust Mouse: Configuring as keyboard
[    31.030] (**) MLK Trust Mouse: YAxisMapping: buttons 4 and 5
[    31.030] (**) MLK Trust Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    31.030] (II) XINPUT: Adding extended input device "MLK Trust Mouse" (type: KEYBOARD)
[    31.030] (**) Option "xkb_rules" "evdev"
[    31.030] (**) Option "xkb_model" "evdev"
[    31.030] (**) Option "xkb_layout" "cz"
[    31.030] (II) MLK Trust Mouse: initialized for relative axes.
[    31.030] (WW) MLK Trust Mouse: ignoring absolute axes.
[    31.031] (II) config/udev: Adding input device MLK Trust Mouse (/dev/input/mouse0)
[    31.031] (II) No input driver/identifier specified (ignoring)
[    31.035] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event4)
[    31.035] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    31.035] (**) AT Translated Set 2 keyboard: always reports core events
[    31.035] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event4"
[    31.070] (II) AT Translated Set 2 keyboard: Found keys
[    31.070] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[    31.070] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
[    31.070] (**) Option "xkb_rules" "evdev"
[    31.070] (**) Option "xkb_model" "evdev"
[    31.070] (**) Option "xkb_layout" "cz"
[    31.070] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event7)
[    31.070] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[    31.070] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[    31.071] (II) LoadModule: "synaptics"
[    31.071] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    31.125] (II) Module synaptics: vendor="X.Org Foundation"
[    31.125] compiled for 1.9.0, module version = 1.2.2
[    31.125] Module class: X.Org XInput Driver
[    31.125] ABI class: X.Org XInput driver, version 11.0
[    31.125] (II) Synaptics touchpad driver version 1.2.2
[    31.125] (**) Option "Device" "/dev/input/event7"
[    31.211] (II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5626
[    31.211] (II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4934
[    31.211] (II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[    31.211] (II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
[    31.211] (II) SynPS/2 Synaptics TouchPad: buttons: left right
[    31.291] (--) SynPS/2 Synaptics TouchPad: touchpad found
[    31.291] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    31.331] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
[    31.331] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[    31.331] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
[    31.331] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[    31.331] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[    31.411] (--) SynPS/2 Synaptics TouchPad: touchpad found
[    31.411] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[    31.411] (II) No input driver/identifier specified (ignoring)
[    36.300] (II) intel(0): EDID vendor "LGD", prod id 503
[    36.300] (II) intel(0): Printing DDC gathered Modelines:
[    36.300] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    36.770] (II) intel(0): EDID vendor "LGD", prod id 503
[    36.770] (II) intel(0): Printing DDC gathered Modelines:
[    36.770] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    37.581] (II) intel(0): EDID vendor "LGD", prod id 503
[    37.667] (II) intel(0): Printing DDC gathered Modelines:
[    37.667] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    38.141] (II) intel(0): EDID vendor "LGD", prod id 503
[    38.141] (II) intel(0): Printing DDC gathered Modelines:
[    38.141] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    44.561] (II) intel(0): EDID vendor "LGD", prod id 503
[    44.561] (II) intel(0): Printing DDC gathered Modelines:
[    44.561] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    47.740] (II) intel(0): EDID vendor "LGD", prod id 503
[    47.740] (II) intel(0): Printing DDC gathered Modelines:
[    47.740] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)

To, co jsem se snazil nastavit v souboru xorg.conf, bylo:

Kód: [Vybrat]

Section "Monitor"
        Identifier      "Acer Monitor"
        # 1368x768 @ 60.00 Hz (GTF) hsync: 47.70 kHz; pclk: 85.86 MHz
        Modeline "1368x768_60.00"  85.86  1368 1440 1584 1800  768 769 772 795  -HSync +Vsync
EndSection

Section "Monitor"
        Identifier      "External Monitor"
        Modeline        "1280x1024_60.00"  108.88  1280 1360 1496 1712  1024 1025 1028 1060  -HSync +Vsync
EndSection

Section "Screen"
        Identifier      "Internal Screen"
        Monitor         "Acer Monitor"
        Device          "Video Card (Primary)"
        SubSection "Display"
                Virtual         1900 1200
                Modes           "1900x1200" "1366x768" "1280x1024"
        EndSubSection
EndSection

Section "Device"
        Identifier      "Video Card (Primary)"
        Option          "Monitor-VGA" "External Monitor"
        Driver           "intel"
EndSection

Předem ještě jednou děkuji za pomoc  

[Filip Dominec]

U LCD to vypadá jako dost neobvyklá závada. Možná to není v samotné obnovovací frekvenci obrazu, ale jen v jeho LED podsvícení.

V téhle recenzi to zmiňují taky: http://netbooked.net/netbook-reviews/review/13.3-acer-aspire-timeline-3810t-core-2-solo-su3500-review/ ... Jestli je tak znát a zároveň to není v Ubuntu, ale v notebooku samotném, tak je to dost úchylné.

[Krysař]

Při zkoumání tohoto problému jsem narazil také na problém, že příkaz glxgears mi ukazuje hodnoty FPS kolem 59 FPS.

Rekl bych, ze to nebude problem, ale vlastnost. Zvlast, pokud to pise stejnou hlasku jako me, tedy, ze jede synchronizovane s vertikalni obnovovaci frekvenci:

Kód: [Vybrat]

:~$ glxgears
Running synchronized to the vertical refresh.  The framerate should be
approximately the same as the monitor refresh rate.
301 frames in 5.0 seconds = 60.157 FPS
300 frames in 5.0 seconds = 59.955 FPS
300 frames in 5.0 seconds = 59.956 FPS

[Lucky-V]

Děkuji za odpovědi. Bohužel nevím jak poznám, zda to je v podsvícení samotném nebo v obnovovací frekvenci. Nicméně pod Windows (konkrétně Windows 7) si žádných takovýchto defektů nevšimnu. Proto jsem bral, že to bude něco s nastavením v Ubuntu. Také to může být tím, že Acer podporuje jen Windows, nikoliv Linuxové distribuce. Ještě mě napadlo, zda jsem ten xorg.conf nenastavil nějak špatně. Nastavoval jsem to podle této předlohy, která je z webu https://help.ubuntu.com/community/AspireTimeline/Fixes:

Kód: [Vybrat]

Section "Monitor"
        Identifier      "Acer Monitor"
EndSection

Section "Monitor"
        Identifier      "External Monitor"
        Modeline        "1280x1024_60.00"  108.88  1280 1360 1496 1712  1024 1025 1028 1060  -HSync +Vsync
EndSection

Section "Screen"
        Identifier      "Internal Screen"
        Monitor         "Acer Monitor"
        Device          "Video Card (Primary)"
        SubSection "Display"
                Virtual         1900 1200
                Modes           "1900x1200" "1366x768" "1280x1024"
        EndSubSection
EndSection

Section "Device"
        Identifier      "Video Card (Primary)"
        Option          "Monitor-VGA" "External Monitor"
EndSection

Jen jsem do sekce Monitor přidal atribut Modeline, podle výstupu příkazu gtf 1366 768 60.0. Do sekce Device jsem ještě přidal atribut Driver "intel". Navíc mě udivuje, že když jsem nastavoval onu obnovovací frekvenci v compiz manageru třeba na hodnotu 5Hz, tak jsem nic neviděl. Vím, že LCD nepracuje jako CRT? ale při tak nízké obnovovací frekvenci bych něco vidět měl (například trhaný obraz), ne?

Ještě jednou předem děkuji

[Roman Vacho]

No zkoušel jsi někdy nastavit sw 5Hz na CRT? Co to dělalo? Ignorovalo.

[Lucky-V]

To jsem nezkoušel. Takovéhle extrémy mě napadli až v souvislosti s tímhle problémem. Bohužel ale nevím co jiného s tímto dělat. Konkrétní problém jsem nikde na internetu bohužel nenašel a nikdo z mého okolí taky neví co s tím. Pokud to není nastavením monitoru / grafické karty, tak to pak bude hold špatnou HW podporou. Nicméně nechápu proč jsem nikde tento problém nenašel. Po pravdě jsem tedy čekal, že budu mít problém jinde, než s blikáním monitoru...

[Krysař]

V sekci screen mas odkaz na "Acer Monitor", ale radek Modeline... mas u "External Monitor" - takze tuto volbu Ti to spolehlive ignoruje 

[Lucky-V]

V sekci screen mas odkaz na "Acer Monitor", ale radek Modeline... mas u "External Monitor" - takze tuto volbu Ti to spolehlive ignoruje 

Ano, to co jsem psal v predeslem postu byla jen predloha kterou jsem pouzil a do ktere jsem doplnil ty informace, ktere jsou napsane pod tou predlohou. Pro prehlednost jsem do meho prvniho prispevku hodil obsah souboru xorg.conf tak, jak jsem ho nastavil ja. Kdybyste byl tedy tak hodny, a mrknul se mi na to tam. Predem dekuji.

[Krysař]

Takto by to melo byt v poradku.
Co na to Xorg.0.log po teto uprave, hlasi neco?

Kdyz ted znovu procitam Xorg.0.log nasel jsem zajimavou vec:

Kód: [Vybrat]

[    29.013] (II) intel(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    29.013] (II) intel(0): v_active: 768  v_sync: 771  v_sync_end 776 v_blanking: 790 v_border: 0
a

Kód: [Vybrat]

[    29.441] (II) intel(0): Output LVDS1 using initial mode 1366x768Je zobrazeni 1368x768 korektni?

Jak se to zachova, kdyz se v xorg.conf zmeni rozliseni na 1366x768 a pouzije se radek "Modeline..." z logu?

Kód: [Vybrat]

Modeline "1366x768_60.0"   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync

[Lucky-V]

Takto by to melo byt v poradku.
Co na to Xorg.0.log po teto uprave, hlasi neco?

Kdyz ted znovu procitam Xorg.0.log nasel jsem zajimavou vec:

Kód: [Vybrat]

[    29.013] (II) intel(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    29.013] (II) intel(0): v_active: 768  v_sync: 771  v_sync_end 776 v_blanking: 790 v_border: 0
a

Kód: [Vybrat]

[    29.441] (II) intel(0): Output LVDS1 using initial mode 1366x768Je zobrazeni 1368x768 korektni?

Jak se to zachova, kdyz se v xorg.conf zmeni rozliseni na 1366x768 a pouzije se radek "Modeline..." z logu?

Kód: [Vybrat]

Modeline "1366x768_60.0"   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync

Jsem idiot... Cpal jsem do xorg.conf špatné rozlišení monitoru. Správné rozlišení je 1366 x 768. Ale opravdu jsem to tak (s těmi špatnými hodnotami) nacpal do souboru xorg.conf. To se tedy divím, že se neobjevil nějaký jiný problém (špatné zobrazení).

Edit: Tak ne. Problém je trochu jinde. Když dám příkaz gtf 1366 768 60, tak výstup tohoto příkazu je:

Kód: [Vybrat]

lucky@lucky-Aspire-3810TZ:~$ gtf 1366 768 60

  # 1368x768 @ 60.00 Hz (GTF) hsync: 47.70 kHz; pclk: 85.86 MHz
  Modeline "1368x768_60.00"  85.86  1368 1440 1584 1800  768 769 772 795  -HSync +Vsync

Nevím jestli je to správně nebo ne, prostě mi to tento výstup hodí. Každopdně v nastavení monitoru mám pořád 1366 x 768 a 60 Hz.

Výstup /var/log/Xorg.0.log je pro dané xorg.conf nastavení:

Kód: [Vybrat]

[    20.579]
X.Org X Server 1.9.0
Release Date: 2010-08-20
[    20.579] X Protocol Version 11, Revision 0
[    20.579] Build Operating System: Linux 2.6.24-27-server x86_64 Ubuntu
[    20.579] Current Operating System: Linux lucky-Aspire-3810TZ 2.6.35-22-generic #35-Ubuntu SMP Sat Oct 16 20:45:36 UTC 2010 x86_64
[    20.579] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic root=UUID=10826288-9456-4288-a24e-5cc2d1e0f694 ro quiet splash
[    20.579] Build Date: 16 September 2010  06:18:41PM
[    20.579] xorg-server 2:1.9.0-0ubuntu7 (For technical support please see http://www.ubuntu.com/support)
[    20.579] Current version of pixman: 0.18.4
[    20.579] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[    20.579] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    20.579] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov  4 11:52:25 2010
[    20.579] (==) Using config file: "/etc/X11/xorg.conf"
[    20.579] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    20.738] (==) No Layout section.  Using the first Screen section.
[    20.738] (**) |-->Screen "Internal Screen" (0)
[    20.738] (**) |   |-->Monitor "Acer Monitor"
[    20.738] (**) |   |-->Device "Video Card (Primary)"
[    20.738] (==) Automatically adding devices
[    20.738] (==) Automatically enabling devices
[    20.738] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    20.738] Entry deleted from font path.
[    20.738] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
[    20.738] (==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[    20.738] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[    20.738] (II) Loader magic: 0x7d0200
[    20.738] (II) Module ABI versions:
[    20.738] X.Org ANSI C Emulation: 0.4
[    20.738] X.Org Video Driver: 8.0
[    20.738] X.Org XInput driver : 11.0
[    20.738] X.Org Server Extension : 4.0
[    20.740] (--) PCI:*(0:0:2:0) 8086:2a42:1025:0229 rev 7, Mem @ 0xe0000000/4194304, 0xd0000000/268435456, I/O @ 0x00003110/8
[    20.740] (--) PCI: (0:0:2:1) 8086:2a43:1025:0229 rev 7, Mem @ 0xe2400000/1048576
[    20.740] (II) Open ACPI successful (/var/run/acpid.socket)
[    20.740] (II) LoadModule: "extmod"
[    20.752] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[    20.752] (II) Module extmod: vendor="X.Org Foundation"
[    20.752] compiled for 1.9.0, module version = 1.0.0
[    20.752] Module class: X.Org Server Extension
[    20.752] ABI class: X.Org Server Extension, version 4.0
[    20.752] (II) Loading extension MIT-SCREEN-SAVER
[    20.752] (II) Loading extension XFree86-VidModeExtension
[    20.752] (II) Loading extension XFree86-DGA
[    20.752] (II) Loading extension DPMS
[    20.752] (II) Loading extension XVideo
[    20.752] (II) Loading extension XVideo-MotionCompensation
[    20.752] (II) Loading extension X-Resource
[    20.752] (II) LoadModule: "dbe"
[    20.753] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[    20.753] (II) Module dbe: vendor="X.Org Foundation"
[    20.753] compiled for 1.9.0, module version = 1.0.0
[    20.753] Module class: X.Org Server Extension
[    20.753] ABI class: X.Org Server Extension, version 4.0
[    20.753] (II) Loading extension DOUBLE-BUFFER
[    20.753] (II) LoadModule: "glx"
[    20.753] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    20.754] (II) Module glx: vendor="X.Org Foundation"
[    20.754] compiled for 1.9.0, module version = 1.0.0
[    20.754] ABI class: X.Org Server Extension, version 4.0
[    20.754] (==) AIGLX enabled
[    20.754] (II) Loading extension GLX
[    20.754] (II) LoadModule: "record"
[    20.754] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    20.754] (II) Module record: vendor="X.Org Foundation"
[    20.754] compiled for 1.9.0, module version = 1.13.0
[    20.754] Module class: X.Org Server Extension
[    20.754] ABI class: X.Org Server Extension, version 4.0
[    20.754] (II) Loading extension RECORD
[    20.755] (II) LoadModule: "dri"
[    20.755] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    20.755] (II) Module dri: vendor="X.Org Foundation"
[    20.755] compiled for 1.9.0, module version = 1.0.0
[    20.755] ABI class: X.Org Server Extension, version 4.0
[    20.755] (II) Loading extension XFree86-DRI
[    20.755] (II) LoadModule: "dri2"
[    20.756] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    20.756] (II) Module dri2: vendor="X.Org Foundation"
[    20.756] compiled for 1.9.0, module version = 1.2.0
[    20.756] ABI class: X.Org Server Extension, version 4.0
[    20.756] (II) Loading extension DRI2
[    20.756] (II) LoadModule: "intel"
[    20.757] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    20.757] (II) Module intel: vendor="X.Org Foundation"
[    20.757] compiled for 1.9.0, module version = 2.12.0
[    20.757] Module class: X.Org Video Driver
[    20.757] ABI class: X.Org Video Driver, version 8.0
[    20.757] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge, Sandybridge, Sandybridge, Sandybridge, Sandybridge,
Sandybridge, Sandybridge
[    20.758] (++) using VT number 7

[    20.762] drmOpenDevice: node name is /dev/dri/card0
[    20.762] drmOpenDevice: open result is 9, (OK)
[    20.762] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[    20.762] drmOpenDevice: node name is /dev/dri/card0
[    20.762] drmOpenDevice: open result is 9, (OK)
[    20.762] drmOpenByBusid: drmOpenMinor returns 9
[    20.762] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[    20.762] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    20.762] (==) intel(0): RGB weight 888
[    20.762] (==) intel(0): Default visual is TrueColor
[    20.762] (II) intel(0): Integrated Graphics Chipset: Intel(R) GM45
[    20.762] (--) intel(0): Chipset: "GM45"
[    20.762] (==) intel(0): video overlay key set to 0x101fe
[    20.800] (II) intel(0): Output VGA1 using monitor section Acer Monitor
[    20.800] (II) intel(0): Output LVDS1 has no monitor section
[    20.800] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
[    20.809] (II) intel(0): Output HDMI1 has no monitor section
[    20.809] (II) intel(0): Output DP1 has no monitor section
[    20.814] (II) intel(0): Output DP2 has no monitor section
[    21.230] (II) intel(0): Output TV1 has no monitor section
[    21.271] (II) intel(0): EDID for output VGA1
[    21.271] (II) intel(0): EDID for output LVDS1
[    21.271] (II) intel(0): Manufacturer: LGD  Model: 1f7  Serial#: 0
[    21.271] (II) intel(0): Year: 2009  Week: 0
[    21.271] (II) intel(0): EDID Version: 1.3
[    21.271] (II) intel(0): Digital Display Input
[    21.271] (II) intel(0): Max Image Size [cm]: horiz.: 29  vert.: 16
[    21.271] (II) intel(0): Gamma: 2.20
[    21.271] (II) intel(0): No DPMS capabilities specified
[    21.271] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[    21.271] (II) intel(0): First detailed timing is preferred mode
[    21.271] (II) intel(0): redX: 0.585 redY: 0.350   greenX: 0.335 greenY: 0.545
[    21.271] (II) intel(0): blueX: 0.160 blueY: 0.135   whiteX: 0.313 whiteY: 0.329
[    21.271] (II) intel(0): Manufacturer's mask: 0
[    21.271] (II) intel(0): Supported detailed timing:
[    21.271] (II) intel(0): clock: 72.3 MHz   Image Size:  293 x 165 mm
[    21.271] (II) intel(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    21.271] (II) intel(0): v_active: 768  v_sync: 771  v_sync_end 776 v_blanking: 790 v_border: 0
[    21.271] (II) intel(0):  
[    21.271] (II) intel(0):  LP133WH2-TLA3
[    21.272] (II) intel(0): EDID (in hex):
[    21.272] (II) intel(0): 00ffffffffffff0030e4f70100000000
[    21.272] (II) intel(0): 00130103801d10780aee259559558b29
[    21.272] (II) intel(0): 22505400000001010101010101010101
[    21.272] (II) intel(0): 0101010101013e1c56a0500016303020
[    21.272] (II) intel(0): 350025a5100000190000000000000000
[    21.272] (II) intel(0): 00000000000000000000000000fe0000
[    21.272] (II) intel(0): 00004c47446973706c61790a000000fe
[    21.272] (II) intel(0): 004c503133335748322d544c413300c2
[    21.272] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[    21.272] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[    21.272] (II) intel(0): Printing probed modes for output LVDS1
[    21.272] (II) intel(0): Modeline "1366x768"x60.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    21.272] (II) intel(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz)
[    21.272] (II) intel(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz)
[    21.273] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[    21.273] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[    21.273] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
[    21.273] (II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
[    21.282] (II) intel(0): EDID for output HDMI1
[    21.282] (II) intel(0): EDID for output DP1
[    21.287] (II) intel(0): EDID for output DP2
[    21.710] (II) intel(0): EDID for output TV1
[    21.710] (II) intel(0): Output VGA1 disconnected
[    21.710] (II) intel(0): Output LVDS1 connected
[    21.710] (II) intel(0): Output HDMI1 disconnected
[    21.710] (II) intel(0): Output DP1 disconnected
[    21.710] (II) intel(0): Output DP2 disconnected
[    21.710] (II) intel(0): Output TV1 disconnected
[    21.710] (II) intel(0): Using exact sizes for initial modes
[    21.710] (II) intel(0): Output LVDS1 using initial mode 1366x768
[    21.710] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    21.710] (II) intel(0): Kernel page flipping support detected, but forcibly disabled.
[    21.710] (==) intel(0): DPI set to (96, 96)
[    21.710] (II) Loading sub module "fb"
[    21.710] (II) LoadModule: "fb"
[    21.710] (II) Loading /usr/lib/xorg/modules/libfb.so
[    21.711] (II) Module fb: vendor="X.Org Foundation"
[    21.711] compiled for 1.9.0, module version = 1.0.0
[    21.711] ABI class: X.Org ANSI C Emulation, version 0.4
[    21.711] (==) Depth 24 pixmap format is 32 bpp
[    21.711] (II) intel(0): [DRI2] Setup complete
[    21.711] (II) intel(0): [DRI2]   DRI driver: i965
[    21.711] (**) intel(0): Tiling enabled
[    21.711] (**) intel(0): SwapBuffers wait enabled
[    21.711] (==) intel(0): VideoRam: 262144 KB
[    21.711] (II) intel(0): Allocated new frame buffer 1920x1200 stride 7680, tiled
[    21.726] (II) UXA(0): Driver registered support for the following operations:
[    21.726] (II)         solid
[    21.726] (II)         copy
[    21.726] (II)         composite (RENDER acceleration)
[    21.726] (II)         put_image
[    21.726] (II)         get_image
[    21.726] (==) intel(0): Backing store disabled
[    21.726] (==) intel(0): Silken mouse enabled
[    21.726] (II) intel(0): Initializing HW Cursor
[    21.780] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    21.781] (==) intel(0): DPMS enabled
[    21.781] (==) intel(0): Intel XvMC decoder enabled
[    21.781] (II) intel(0): Set up textured video
[    21.781] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[    21.781] (II) intel(0): direct rendering: DRI2 Enabled
[    21.781] (WW) intel(0): Option "Monitor-VGA" is not used
[    21.781] (--) RandR disabled
[    21.781] (II) Initializing built-in extension Generic Event Extension
[    21.781] (II) Initializing built-in extension SHAPE
[    21.781] (II) Initializing built-in extension MIT-SHM
[    21.781] (II) Initializing built-in extension XInputExtension
[    21.781] (II) Initializing built-in extension XTEST
[    21.782] (II) Initializing built-in extension BIG-REQUESTS
[    21.782] (II) Initializing built-in extension SYNC
[    21.782] (II) Initializing built-in extension XKEYBOARD
[    21.782] (II) Initializing built-in extension XC-MISC
[    21.782] (II) Initializing built-in extension SECURITY
[    21.782] (II) Initializing built-in extension XINERAMA
[    21.782] (II) Initializing built-in extension XFIXES
[    21.782] (II) Initializing built-in extension RENDER
[    21.782] (II) Initializing built-in extension RANDR
[    21.782] (II) Initializing built-in extension COMPOSITE
[    21.782] (II) Initializing built-in extension DAMAGE
[    21.782] (II) Initializing built-in extension GESTURE
[    21.796] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    21.796] (II) AIGLX: enabled GLX_INTEL_swap_event
[    21.796] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    21.796] (II) AIGLX: enabled GLX_SGI_make_current_read
[    21.796] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    21.797] (II) AIGLX: Loaded and initialized /usr/lib/dri/i965_dri.so
[    21.797] (II) GLX: Initialized DRI2 GL provider for screen 0
[    21.797] (II) intel(0): Setting screen physical size to 361 x 203
[    21.797] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[    21.857] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[    21.871] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    21.871] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    21.871] (II) LoadModule: "evdev"
[    21.871] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    21.871] (II) Module evdev: vendor="X.Org Foundation"
[    21.871] compiled for 1.9.0, module version = 2.3.2
[    21.871] Module class: X.Org XInput Driver
[    21.871] ABI class: X.Org XInput driver, version 11.0
[    21.872] (**) Power Button: always reports core events
[    21.872] (**) Power Button: Device: "/dev/input/event3"
[    21.901] (II) Power Button: Found keys
[    21.901] (II) Power Button: Configuring as keyboard
[    21.901] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    21.901] (**) Option "xkb_rules" "evdev"
[    21.901] (**) Option "xkb_model" "evdev"
[    21.901] (**) Option "xkb_layout" "cz"
[    21.904] (II) XKB: reuse xkmfile /var/lib/xkb/server-A54AEDFEFDBEDDA8B4D3BCC5AF2299BD6BD0DEB7.xkm
[    21.905] (II) config/udev: Adding input device Video Bus (/dev/input/event8)
[    21.905] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    21.905] (**) Video Bus: always reports core events
[    21.905] (**) Video Bus: Device: "/dev/input/event8"
[    21.931] (II) Video Bus: Found keys
[    21.931] (II) Video Bus: Configuring as keyboard
[    21.931] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[    21.931] (**) Option "xkb_rules" "evdev"
[    21.931] (**) Option "xkb_model" "evdev"
[    21.931] (**) Option "xkb_layout" "cz"
[    21.935] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    21.935] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    21.935] (**) Power Button: always reports core events
[    21.935] (**) Power Button: Device: "/dev/input/event0"
[    21.961] (II) Power Button: Found keys
[    21.961] (II) Power Button: Configuring as keyboard
[    21.961] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    21.961] (**) Option "xkb_rules" "evdev"
[    21.961] (**) Option "xkb_model" "evdev"
[    21.961] (**) Option "xkb_layout" "cz"
[    21.962] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[    21.962] (II) No input driver/identifier specified (ignoring)
[    21.962] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[    21.962] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[    21.962] (**) Sleep Button: always reports core events
[    21.962] (**) Sleep Button: Device: "/dev/input/event2"
[    21.962] (II) Sleep Button: Found keys
[    21.962] (II) Sleep Button: Configuring as keyboard
[    21.962] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
[    21.962] (**) Option "xkb_rules" "evdev"
[    21.962] (**) Option "xkb_model" "evdev"
[    21.962] (**) Option "xkb_layout" "cz"
[    21.965] (II) config/udev: Adding input device HD Video WebCam (/dev/input/event6)
[    21.965] (**) HD Video WebCam: Applying InputClass "evdev keyboard catchall"
[    21.965] (**) HD Video WebCam: always reports core events
[    21.965] (**) HD Video WebCam: Device: "/dev/input/event6"
[    21.965] (II) HD Video WebCam: Found keys
[    21.965] (II) HD Video WebCam: Configuring as keyboard
[    21.965] (II) XINPUT: Adding extended input device "HD Video WebCam" (type: KEYBOARD)
[    21.965] (**) Option "xkb_rules" "evdev"
[    21.965] (**) Option "xkb_model" "evdev"
[    21.965] (**) Option "xkb_layout" "cz"
[    21.968] (II) config/udev: Adding input device MLK Trust Mouse (/dev/input/event5)
[    21.968] (**) MLK Trust Mouse: Applying InputClass "evdev pointer catchall"
[    21.968] (**) MLK Trust Mouse: Applying InputClass "evdev keyboard catchall"
[    21.968] (**) MLK Trust Mouse: always reports core events
[    21.968] (**) MLK Trust Mouse: Device: "/dev/input/event5"
[    21.970] (II) MLK Trust Mouse: Found 9 mouse buttons
[    21.970] (II) MLK Trust Mouse: Found scroll wheel(s)
[    21.970] (II) MLK Trust Mouse: Found relative axes
[    21.970] (II) MLK Trust Mouse: Found x and y relative axes
[    21.970] (II) MLK Trust Mouse: Found absolute axes
[    21.970] (II) evdev-grail: failed to open grail, no gesture support
[    21.970] (II) MLK Trust Mouse: Found keys
[    21.970] (II) MLK Trust Mouse: Configuring as mouse
[    21.970] (II) MLK Trust Mouse: Configuring as keyboard
[    21.970] (**) MLK Trust Mouse: YAxisMapping: buttons 4 and 5
[    21.970] (**) MLK Trust Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    21.970] (II) XINPUT: Adding extended input device "MLK Trust Mouse" (type: KEYBOARD)
[    21.970] (**) Option "xkb_rules" "evdev"
[    21.970] (**) Option "xkb_model" "evdev"
[    21.970] (**) Option "xkb_layout" "cz"
[    21.970] (II) MLK Trust Mouse: initialized for relative axes.
[    21.970] (WW) MLK Trust Mouse: ignoring absolute axes.
[    21.971] (II) config/udev: Adding input device MLK Trust Mouse (/dev/input/mouse0)
[    21.971] (II) No input driver/identifier specified (ignoring)
[    21.975] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event4)
[    21.975] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    21.975] (**) AT Translated Set 2 keyboard: always reports core events
[    21.975] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event4"
[    22.011] (II) AT Translated Set 2 keyboard: Found keys
[    22.011] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[    22.011] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
[    22.011] (**) Option "xkb_rules" "evdev"
[    22.011] (**) Option "xkb_model" "evdev"
[    22.011] (**) Option "xkb_layout" "cz"
[    22.012] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event7)
[    22.012] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[    22.012] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[    22.012] (II) LoadModule: "synaptics"
[    22.012] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    22.012] (II) Module synaptics: vendor="X.Org Foundation"
[    22.012] compiled for 1.9.0, module version = 1.2.2
[    22.012] Module class: X.Org XInput Driver
[    22.012] ABI class: X.Org XInput driver, version 11.0
[    22.012] (II) Synaptics touchpad driver version 1.2.2
[    22.012] (**) Option "Device" "/dev/input/event7"
[    22.131] (II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5626
[    22.131] (II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4934
[    22.131] (II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[    22.131] (II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
[    22.131] (II) SynPS/2 Synaptics TouchPad: buttons: left right
[    22.211] (--) SynPS/2 Synaptics TouchPad: touchpad found
[    22.211] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    22.251] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
[    22.251] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[    22.251] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
[    22.251] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[    22.251] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[    22.331] (--) SynPS/2 Synaptics TouchPad: touchpad found
[    22.331] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[    22.331] (II) No input driver/identifier specified (ignoring)
[    23.201] (II) intel(0): EDID vendor "LGD", prod id 503
[    23.201] (II) intel(0): Printing DDC gathered Modelines:
[    23.201] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    23.670] (II) intel(0): EDID vendor "LGD", prod id 503
[    23.670] (II) intel(0): Printing DDC gathered Modelines:
[    23.670] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    24.140] (II) intel(0): EDID vendor "LGD", prod id 503
[    24.140] (II) intel(0): Printing DDC gathered Modelines:
[    24.140] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    24.661] (II) intel(0): EDID vendor "LGD", prod id 503
[    24.661] (II) intel(0): Printing DDC gathered Modelines:
[    24.661] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    25.961] (II) intel(0): EDID vendor "LGD", prod id 503
[    25.961] (II) intel(0): Printing DDC gathered Modelines:
[    25.961] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    30.640] (II) intel(0): EDID vendor "LGD", prod id 503
[    30.640] (II) intel(0): Printing DDC gathered Modelines:
[    30.640] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[    60.630] (II) intel(0): EDID vendor "LGD", prod id 503
[    60.630] (II) intel(0): Printing DDC gathered Modelines:
[    60.630] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[   269.440] (II) intel(0): EDID vendor "LGD", prod id 503
[   269.440] (II) intel(0): Printing DDC gathered Modelines:
[   269.440] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[   276.080] (II) intel(0): EDID vendor "LGD", prod id 503
[   276.080] (II) intel(0): Printing DDC gathered Modelines:
[   276.080] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[   276.560] (II) intel(0): EDID vendor "LGD", prod id 503
[   276.560] (II) intel(0): Printing DDC gathered Modelines:
[   276.560] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[   277.323] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[   322.870] (II) intel(0): EDID vendor "LGD", prod id 503
[   322.870] (II) intel(0): Printing DDC gathered Modelines:
[   322.870] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[   323.350] (II) intel(0): EDID vendor "LGD", prod id 503
[   323.350] (II) intel(0): Printing DDC gathered Modelines:
[   323.350] (II) intel(0): Modeline "1366x768"x0.0   72.30  1366 1414 1446 1526  768 771 776 790 -hsync -vsync (47.4 kHz)
[   323.833] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled

Až budu doma, zkusím ještě výstup do externího monitoru (jak vypadá). Také mě napadá, zda nemůže být nějaký problém se samotným podsvícením? Že se třeba rychle vypíná a zapíná nebo něco podobného? Pořád mi totiž nejde do hlavy, že by LCD samo o sobě jako takové blikalo (myslel jsem, že tohle dělalo jen CRT).

[Krysař]

To se stane.     ty dva pixely na sirku asi nejsou tak moc, tak to monitor zvladnul.

To ja skoro 2 roky zapasil s tim, ze mi monitor nesel v nativnim rozliseni - zobrazil sice spravne, ale neprijal ho jako nativni, takze nektere svisle cary byly "rozostrene". Nakonec jsem prisel na to, ze GTF dava jine hodnoty, nez EDID monitoru a kdyz jsem do xorg.conf napsal to, co bylo v Xorg.0.log vycucane z EDID, tak konecne monitor zobrazil ostra pismenka.

[Lucky-V]

Když jsem ty hodnoty přepsal podle toho z Xorg.0.log, tak se to chová pořád naprosto stejně. Začínám se bát, že se to z toho xorg.conf vůbec nenačítá :-/

[Krysař]

Podle

[    21.781] (WW) intel(0): Option "Monitor-VGA" is not used

si s tim nejak nerozumi.

Zkus vynechat cely ten radek v xorg.conf

Kód: [Vybrat]

        Option          "Monitor-VGA" "External Monitor" a taky ten ext monitor

Kód: [Vybrat]

Section "Monitor"
        Identifier      "External Monitor"
        Modeline        "1280x1024_60.00"  108.88  1280 1360 1496 1712  1024 1025 1028 1060  -HSync +Vsync
EndSectionat se to tam neplete.

[Roman Vacho]

Stačí zakomentovat počátek řádku znakem na "klávese 3".

[Lucky-V]

Zakomentování provedeno, onen Warning z logu zmizel. Monitor ale pořád bliká, takže si myslím, že to s tím xorgem jako takovým nemá nic společného. Otázkou opravdu je, zda s tím má co dočinění grafická karta, nebo ovládání podsvícení. To ale opravdu netuším jak se nastavuje (to podsvícení). Zkusím někde opět hledat...

[Lucky-V]

Tak to vypadá na problém s jádrem, viz například https://bugzilla.redhat.com/show_bug.cgi?id=580276
Smůla no

[Lucky-V]

Tak ještě poslední poznatek, kterým toto v podstatě mohu ukončit. Vyzkoušel jsem ta jádra, na kterých to mělo podle výše zmíněného odkazu fungovat. Samozřejmě to nepomohlo. Problém je tedy možná u obou případu v blikání, ale u každého to blikání znamená něco jiného.

Jelikož má přítelkyně naprosto stejný model notebooku, zkusil jsem u ní spustit live verzi Ubuntu 10.10 (stejnou jako jsem zkoušel u mě) a co nevidím? U ní to ani nebliklo. Napadla mě poslední věc, a to provést u mě downgrade biosu na verzi, kterou tam má ona (měla verzi 1.20). Jelikož ani to nepomohlo a mě to pořád v Linuxu bliká (ve Windowsech to funguje bez problémů), beru to tak, že mám nejspíš s Linuxem smůlu. To, že to v Linuxu bliká a ve Windowsech ne nemá na reklamaci nárok a nic jiného mě opravdu už nenapadá.

Tímto tedy děkuji všem za pomoc
a ahoj...

[Roman Vacho]

Tak ho vyměň s přítelkyní

[Lucky-V]

Fakt ne Přece nebudu dávat své polovičce nějaký šunt