Apache NOD280 nejede WiFi- pls POMOZTE

[AllKalda]

Dobrý den, žádám vás touto cestou o pomoc při instalaci WiFi na tomto netbooku. podařilo se mi zprovoznit vše až na tuto kartu. Když mám notes připojený drátem tak internet funguje, ale i po aktualizacích mi nehlásí žádný ovladač. Důkladně jsem prostudoval toto forum, vyzkoušel jsem i ext programy na instal ovladače přes inf soubor ale stale mi to nehlasi podporovaný hardware. výsledky v terminálu :
eth0      Link encap:Ethernet  HWadr 00:e0:4c:12:3c:63 
          inet adr:10.0.0.2  Všesměr:10.0.0.255  Maska:255.255.255.0
          inet6-adr: fe80::2e0:4cff:fe12:3c63/64 Rozsah:Linka
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:17740 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12060 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 26371037 (26.3 MB) Odesláno bajtů: 930509 (930.5 KB)
          Přerušení:41

lo        Link encap:Místní smyčka 
          inet adr:127.0.0.1  Maska:255.0.0.0
          inet6-adr: ::1/128 Rozsah:Počítač
          AKTIVOVÁNO SMYČKA BĚŽÍ  MTU:16436  Metrika:1
          RX packets:16 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 960 (960.0 B) Odesláno bajtů: 960 (960.0 B)

A zde je typ netbooku : http://www.alza.cz/apache-not240-cerny-ultra-slim-d164950.htm
Budu vděčný za jakoukoliv pomoc. Ještě podotknu že jsem začátečník a opravdu jsem se snažil vygooglit jakoukoliv pomoc ale bez uspěchu

[AllKalda]

Opravdu nikdo nepomůže? Je možné abych na tom WiFi nerozchodil?

[jAster_BA]

Otvor terminál a zadaj tam toto

Kód: [Vybrat]

lspci | grep -i wireless
výstup sem.

[AllKalda]

00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)

když jsem tam zadal celej příklad tak mi to nešli, takže toto je jen ten výpis z lspci

[jAster_BA]

Nainštaluj HWinfo

Kód: [Vybrat]

sudo apt-get install hwinfo a potom

Kód: [Vybrat]

hwinfo wlan

[AllKalda]

 

Kód: [Vybrat]

PCI 1f.3: 0c05 SMBus
  [Created at pci.318]
  Unique ID: nS1_.MH+te_OwL+A
  SysFS ID: /devices/pci0000:00/0000:00:1f.3
  SysFS BusID: 0000:00:1f.3
  Hardware Class: unknown
  Model: "Intel 82801G (ICH7 Family) SMBus Controller"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x27da "82801G (ICH7 Family) SMBus Controller"
  SubVendor: pci 0x8086 "Intel Corporation"
  SubDevice: pci 0x1999
  Revision: 0x02
  I/O Ports: 0x18e0-0x18ff (rw)
  IRQ: 10 (no events)
  Module Alias: "pci:v00008086d000027DAsv00008086sd00001999bc0Csc05i00"
  Driver Info #0:
    Driver Status: i2c_i801 is not active
    Driver Activation Cmd: "modprobe i2c_i801"
  Config Status: cfg=new, avail=yes, need=no, active=unknown

26: PCI 200.0: 0200 Ethernet controller
  [Created at pci.318]
  Unique ID: rBUF._q7bCQPGty7
  Parent ID: z8Q3.b0oB+Q+5kI8
  SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:02:00.0
  SysFS BusID: 0000:02:00.0
  Hardware Class: network
  Model: "Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8136 "RTL8101E/RTL8102E PCI Express Fast Ethernet controller"
  SubVendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  SubDevice: pci 0x8136
  Revision: 0x02
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  I/O Ports: 0x2000-0x2fff (rw)
  Memory Range: 0xd0010000-0xd0010fff (ro,non-prefetchable)
  Memory Range: 0xd0000000-0xd000ffff (ro,non-prefetchable)
  Memory Range: 0xd0020000-0xd003ffff (ro,non-prefetchable,disabled)
  IRQ: 41 (7393 events)
  HW Address: 00:e0:4c:12:3c:63
  Link detected: yes
  Module Alias: "pci:v000010ECd00008136sv000010ECsd00008136bc02sc00i00"
  Driver Info #0:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)

27: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: z9pp.+GmdJItMGB9
  SysFS ID: /devices/pnp0/00:00
  SysFS BusID: 00:00
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0a08
  Config Status: cfg=new, avail=yes, need=no, active=unknown

28: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: QL3u.B+yZ9Ve8gC1
  SysFS ID: /devices/pnp0/00:01
  SysFS BusID: 00:01
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0c02
  Config Status: cfg=new, avail=yes, need=no, active=unknown

29: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: tWJy.ld94kxNGZf5
  SysFS ID: /devices/pnp0/00:02
  SysFS BusID: 00:02
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0200
  Config Status: cfg=new, avail=yes, need=no, active=unknown

30: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: KiZ0.jDhFyyFrbg5
  SysFS ID: /devices/pnp0/00:03
  SysFS BusID: 00:03
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: INT
  SubDevice: eisa 0x0800
  Config Status: cfg=new, avail=yes, need=no, active=unknown

31: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: ntp4.fG36JLVNse9
  SysFS ID: /devices/pnp0/00:04
  SysFS BusID: 00:04
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0103
  Config Status: cfg=new, avail=yes, need=no, active=unknown

32: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: E349.DE8RM9cWQQ8
  SysFS ID: /devices/pnp0/00:05
  SysFS BusID: 00:05
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0c04
  Config Status: cfg=new, avail=yes, need=no, active=unknown

33: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: hEKD.B+yZ9Ve8gC1
  SysFS ID: /devices/pnp0/00:06
  SysFS BusID: 00:06
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0c02
  Config Status: cfg=new, avail=yes, need=no, active=unknown

34: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: NhVi.B+yZ9Ve8gC1
  SysFS ID: /devices/pnp0/00:07
  SysFS BusID: 00:07
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0c02
  Config Status: cfg=new, avail=yes, need=no, active=unknown

35: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: qslm.WYwRElrJa93
  SysFS ID: /devices/pnp0/00:08
  SysFS BusID: 00:08
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0b00
  Config Status: cfg=new, avail=yes, need=no, active=unknown

36: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: H20r.xhndlW9HXJ7
  SysFS ID: /devices/pnp0/00:09
  SysFS BusID: 00:09
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0303
  Config Status: cfg=new, avail=yes, need=no, active=unknown

37: ISA(PnP) 00.0: 0000 Unclassified device
  [Created at isapnp.142]
  Unique ID: iT2w.t7Yh1tpgb13
  SysFS ID: /devices/pnp0/00:0a
  SysFS BusID: 00:0a
  Hardware Class: unknown
  Model: "Unclassified device"
  SubVendor: PNP "PnP"
  SubDevice: eisa 0x0f13
  Config Status: cfg=new, avail=yes, need=no, active=unknown

38: IDE 200.0: 10600 Disk
  [Created at block.243]
  Unique ID: 3OOL.DASMVrkWpz5
  Parent ID: w7Y8.0rAlOlkGMUF
  SysFS ID: /class/block/sda
  SysFS BusID: 2:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:1f.2/host2/target2:0:0/2:0:0:0
  Hardware Class: disk
  Model: "WDC WD3200BEVT-2"
  Vendor: "WDC"
  Device: "WD3200BEVT-2"
  Revision: "01.0"
  Driver: "ata_piix", "sd"
  Driver Modules: "ata_piix"
  Device File: /dev/sda
  Device Files: /dev/sda, /dev/disk/by-id/ata-WDC_WD3200BEVT-22A23T0_WD-WX70AA9D1596, /dev/disk/by-id/scsi-SATA_WDC_WD3200BEVT-_WD-WX70AA9D1596, /dev/disk/by-path/pci-0000:00:1f.2-scsi-0:0:0:0, /dev/disk/by-id/wwn-0x50014ee2ae496f4f
  Device Number: block 8:0-8:15
  BIOS id: 0x80
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #24 (IDE interface)

39: None 00.0: 11300 Partition
  [Created at block.412]
  Unique ID: bdUI.SE1wIdpsiiC
  Parent ID: 3OOL.DASMVrkWpz5
  SysFS ID: /class/block/sda/sda1
  Hardware Class: partition
  Model: "Partition"
  Device File: /dev/sda1
  Device Files: /dev/sda1, /dev/disk/by-id/ata-WDC_WD3200BEVT-22A23T0_WD-WX70AA9D1596-part1, /dev/disk/by-id/scsi-SATA_WDC_WD3200BEVT-_WD-WX70AA9D1596-part1, /dev/disk/by-path/pci-0000:00:1f.2-scsi-0:0:0:0-part1, /dev/disk/by-uuid/0862416a-fb59-486e-91fe-84788b07d837, /dev/disk/by-id/wwn-0x50014ee2ae496f4f-part1, /dev/root
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #38 (Disk)

40: None 00.0: 11300 Partition
  [Created at block.412]
  Unique ID: 2pkM.SE1wIdpsiiC
  Parent ID: 3OOL.DASMVrkWpz5
  SysFS ID: /class/block/sda/sda2
  Hardware Class: partition
  Model: "Partition"
  Device File: /dev/sda2
  Device Files: /dev/sda2, /dev/disk/by-id/ata-WDC_WD3200BEVT-22A23T0_WD-WX70AA9D1596-part2, /dev/disk/by-id/scsi-SATA_WDC_WD3200BEVT-_WD-WX70AA9D1596-part2, /dev/disk/by-path/pci-0000:00:1f.2-scsi-0:0:0:0-part2, /dev/disk/by-id/wwn-0x50014ee2ae496f4f-part2
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #38 (Disk)

41: None 00.0: 11300 Partition
  [Created at block.412]
  Unique ID: QLVZ.SE1wIdpsiiC
  Parent ID: 3OOL.DASMVrkWpz5
  SysFS ID: /class/block/sda/sda5
  Hardware Class: partition
  Model: "Partition"
  Device File: /dev/sda5
  Device Files: /dev/sda5, /dev/disk/by-id/ata-WDC_WD3200BEVT-22A23T0_WD-WX70AA9D1596-part5, /dev/disk/by-id/scsi-SATA_WDC_WD3200BEVT-_WD-WX70AA9D1596-part5, /dev/disk/by-path/pci-0000:00:1f.2-scsi-0:0:0:0-part5, /dev/disk/by-uuid/b1a06f05-0ba5-4818-a2b5-8827f67550fb, /dev/disk/by-id/wwn-0x50014ee2ae496f4f-part5
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #38 (Disk)

42: USB 00.0: 10a00 Hub
  [Created at usb.122]
  Unique ID: k4bc.9T1GDCLyFd9
  Parent ID: 5YuN.c3V9hatT5fD
  SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-0:1.0
  SysFS BusID: 1-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.38-11-generic ehci_hcd EHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.38-11-generic ehci_hcd"
  Device: usb 0x0002 "EHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:1d.7"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 480 Mbps
  Module Alias: "usb:v1D6Bp0002d0206dc09dsc00dp00ic09isc00ip00"
  Driver Info #0:
    Driver Status: option is not active
    Driver Activation Cmd: "modprobe option"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #20 (USB Controller)

43: USB 00.0: 10a00 Hub
  [Created at usb.122]
  Unique ID: pBe4.v+N+B0xY+P6
  Parent ID: 1GTX.2P7_TEwuSH7
  SysFS ID: /devices/pci0000:00/0000:00:1d.0/usb2/2-0:1.0
  SysFS BusID: 2-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.38-11-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.38-11-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:1d.0"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #16 (USB Controller)

44: USB 00.0: 10a00 Hub
  [Created at usb.122]
  Unique ID: uIhY.gkSaZmjGyhD
  Parent ID: vayM.Zp3kyo1c_f7
  SysFS ID: /devices/pci0000:00/0000:00:1d.1/usb3/3-0:1.0
  SysFS BusID: 3-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.38-11-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.38-11-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:1d.1"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #17 (USB Controller)

45: USB 00.0: 10a00 Hub
  [Created at usb.122]
  Unique ID: zPk0.RTX9xWW_uz4
  Parent ID: mvRC.4E0URN9JW28
  SysFS ID: /devices/pci0000:00/0000:00:1d.2/usb4/4-0:1.0
  SysFS BusID: 4-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.38-11-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.38-11-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:1d.2"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #18 (USB Controller)

46: USB 00.0: 10a00 Hub
  [Created at usb.122]
  Unique ID: 2XnU.CCckIHJirFC
  Parent ID: eEx1.beyDwxG02R8
  SysFS ID: /devices/pci0000:00/0000:00:1d.3/usb5/5-0:1.0
  SysFS BusID: 5-0:1.0
  Hardware Class: hub
  Model: "Linux 2.6.38-11-generic uhci_hcd UHCI Host Controller"
  Hotplug: USB
  Vendor: usb 0x1d6b "Linux 2.6.38-11-generic uhci_hcd"
  Device: usb 0x0001 "UHCI Host Controller"
  Revision: "2.06"
  Serial ID: "0000:00:1d.3"
  Driver: "hub"
  Driver Modules: "usbcore"
  Speed: 12 Mbps
  Module Alias: "usb:v1D6Bp0001d0206dc09dsc00dp00ic09isc00ip00"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #19 (USB Controller)

47: USB 00.0: 0000 Unclassified device
  [Created at usb.122]
  Unique ID: 2UT6.b14ti7kY791
  Parent ID: k4bc.9T1GDCLyFd9
  SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3:1.0
  SysFS BusID: 1-3:1.0
  Hardware Class: unknown
  Model: "FITIPOWERCORP.̒200 USB 2.0 Camera"
  Hotplug: USB
  Vendor: usb 0x18e3 "FITIPOWERCORP.̒200"
  Device: usb 0x9512 "USB 2.0 Camera"
  Revision: "9.02"
  Serial ID: "20070327"
  Driver: "uvcvideo"
  Driver Modules: "uvcvideo"
  Speed: 480 Mbps
  Module Alias: "usb:v18E3p9512d0902dcEFdsc02dp01ic0Eisc01ip00"
  Driver Info #0:
    Driver Status: uvcvideo is active
    Driver Activation Cmd: "modprobe uvcvideo"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #42 (Hub)

49: USB 00.0: 0000 Unclassified device
  [Created at usb.122]
  Unique ID: wkjR.GcR7qb7SOkA
  Parent ID: k4bc.9T1GDCLyFd9
  SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0
  SysFS BusID: 1-5:1.0
  Hardware Class: unknown
  Model: "Syntek WiFi USB Dongle"
  Hotplug: USB
  Vendor: usb 0x05e1 "Syntek Semiconductor Co., Ltd"
  Device: usb 0x0100 "WiFi USB Dongle"
  Revision: "0.02"
  Serial ID: "Manufacture"
  Speed: 480 Mbps
  Module Alias: "usb:v05E1p0100d0002dc00dsc00dp00icFFiscFFipFF"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #42 (Hub)

51: USB 00.0: 10503 USB Mouse
  [Created at usb.122]
  Unique ID: rg_L.4V1_q5x47S0
  Parent ID: zPk0.RTX9xWW_uz4
  SysFS ID: /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0
  SysFS BusID: 4-2:1.0
  Hardware Class: mouse
  Model: "KYE 2.4G Wireless Mouse"
  Hotplug: USB
  Vendor: usb 0x0458 "KYE Systems"
  Device: usb 0x00b4 "2.4G Wireless Mouse"
  Revision: "6.19"
  Compatible to: int 0x0210 0x0033
  Driver: "usbhid"
  Driver Modules: "usbhid"
  Device File: /dev/input/mice (/dev/input/mouse0)
  Device Files: /dev/input/mice, /dev/input/mouse0, /dev/input/event6, /dev/input/by-id/usb-Genius_2.4G_Wireless_Mouse-event-mouse, /dev/input/by-path/pci-0000:00:1d.2-usb-0:2:1.0-event-mouse, /dev/input/by-id/usb-Genius_2.4G_Wireless_Mouse-mouse, /dev/input/by-path/pci-0000:00:1d.2-usb-0:2:1.0-mouse
  Device Number: char 13:63 (char 13:32)
  Speed: 1.5 Mbps
  Module Alias: "usb:v0458p00B4d0619dc00dsc00dp00ic03isc01ip02"
  Driver Info #0:
    Buttons: 3
    Wheels: 3
    XFree86 Protocol: explorerps/2
    GPM Protocol: exps2
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #45 (Hub)

52: PS/2 00.0: 10800 Keyboard
  [Created at input.161]
  Unique ID: c3zD.+49ps10DtUF
  Hardware Class: keyboard
  Model: "AT Translated Set 2 keyboard"
  Vendor: 0x0001
  Device: 0x0001 "AT Translated Set 2 keyboard"
  Compatible to: int 0x0211 0x0001
  Device File: /dev/input/event4
  Device Files: /dev/input/event4, /dev/input/by-path/platform-i8042-serio-0-event-kbd
  Device Number: char 13:68
  Driver Info #0:
    XkbRules: xfree86
    XkbModel: pc104
  Config Status: cfg=new, avail=yes, need=no, active=unknown

53: PS/2 00.0: 10500 PS/2 Mouse
  [Created at input.183]
  Unique ID: AH6Q.E+tlAXm68p6
  Hardware Class: mouse
  Model: "FSPPS/2 Sentelic FingerSensingPad"
  Vendor: 0x0002
  Device: 0x000f "FSPPS/2 Sentelic FingerSensingPad"
  Compatible to: int 0x0210 0x0025
  Device File: /dev/input/mice (/dev/input/mouse1)
  Device Files: /dev/input/mice, /dev/input/mouse1, /dev/input/event7, /dev/input/by-path/platform-i8042-serio-1-event-mouse, /dev/input/by-path/platform-i8042-serio-1-mouse
  Device Number: char 13:63 (char 13:33)
  Driver Info #0:
    Buttons: 5
    Wheels: 2
    XFree86 Protocol: explorerps/2
    GPM Protocol: exps2
  Config Status: cfg=new, avail=yes, need=no, active=unknown

54: None 00.0: 10103 CPU
  [Created at cpu.304]
  Unique ID: rdCR.j8NaKXDZtZ6
  Hardware Class: cpu
  Arch: Intel
  Vendor: "GenuineIntel"
  Model: 6.28.2 "Intel(R) Atom(TM) CPU N280   @ 1.66GHz"
  Features: fpu,vme,de,tsc,msr,pae,mce,cx8,apic,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,ht,tm,pbe,nx,constant_tsc,arch_perfmon,pebs,bts,aperfmperf,pni,dtes64,ds_cpl,est,tm2,ssse3,xtpr,pdcm,movbe,lahf_lm,dts
  Clock: 1666 MHz
  BogoMips: 3332.81
  Cache: 512 kb
  Units/Processor: 2
  Config Status: cfg=new, avail=yes, need=no, active=unknown

55: None 01.0: 10103 CPU
  [Created at cpu.304]
  Unique ID: wkFv.j8NaKXDZtZ6
  Hardware Class: cpu
  Arch: Intel
  Vendor: "GenuineIntel"
  Model: 6.28.2 "Intel(R) Atom(TM) CPU N280   @ 1.66GHz"
  Features: fpu,vme,de,tsc,msr,pae,mce,cx8,apic,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,ht,tm,pbe,nx,constant_tsc,arch_perfmon,pebs,bts,aperfmperf,pni,dtes64,ds_cpl,est,tm2,ssse3,xtpr,pdcm,movbe,lahf_lm,dts
  Clock: 1666 MHz
  BogoMips: 3333.32
  Cache: 512 kb
  Units/Processor: 2
  Config Status: cfg=new, avail=yes, need=no, active=unknown

56: None 00.0: 10700 Loopback
  [Created at net.124]
  Unique ID: ZsBS.GQNx7L4uPNA
  SysFS ID: /class/net/lo
  Hardware Class: network interface
  Model: "Loopback network interface"
  Device File: lo
  Link detected: yes
  Config Status: cfg=new, avail=yes, need=no, active=unknown

57: None 00.0: 10701 Ethernet
  [Created at net.124]
  Unique ID: usDW.ndpeucax6V1
  Parent ID: rBUF._q7bCQPGty7
  SysFS ID: /class/net/eth0
  SysFS Device Link: /devices/pci0000:00/0000:00:1c.0/0000:02:00.0
  Hardware Class: network interface
  Model: "Ethernet network interface"
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  HW Address: 00:e0:4c:12:3c:63
  Link detected: yes
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #26 (Ethernet controller)

_{//výpisy dávejte do #code}

[petertomasy]

používaš wifi v usb-čku?

Model: "Syntek WiFi USB Dongle"
  Hotplug: USB
  Vendor: usb 0x05e1 "Syntek Semiconductor Co., Ltd"
  Device: usb 0x0100 "WiFi USB Dongle"
  Revision: "0.02"

[AllKalda]

nee, tato WiFi je přímo v notesu

[AllKalda]

Dle uvedení výrobce by tam mělo být Wi-Fi - 802.11 a/b/g, další info bohužel nedokážu dohledat

[petertomasy]

uff asi by tu bulo riešenie , ale by si musel , po hladaní na googli , použiť starsie jadro , zdrojové kody nejsou k mání. skus sa pozrieť sem priznám sa je to asi špecifický hardware. preštuduj si vlákno , ale si myslím že riešenie je v celku jednoduché... ak tak sa ozvy.

[AllKalda]

Díky za odkaz, koukam teď na to. Přiznám se že jsem z toho moc nepochopil :-( . Hledám to v kuse už druhý den...

[petertomasy]

ešte jednoduchšie https://github.com/reyiyo/3dsp/

Kód: [Vybrat]

sudo aptitude install build-essential linux-headers-`uname -r`
git clone http://github.com/reyiyo/3dsp.git
cd 3dsp
sudo bash Install_3DSPUSB.sh
vyskúšal tento postup a inštalácia prebehla bez erroru

edit :

Kód: [Vybrat]

sudo ./Install_3DSPUSB.sh
[sudo] password for peter:
 * Compiling the drivers, it will take some minutes...
 * Installing the drivers...
 * Installing the WB and wbtool...
 * Installing the 3dsp-wifi-radar...
 * Creating the init scripts...
 * Loading the modules...
peter@peter:~/Plocha/reyiyo-3dsp-f01bd9d$ lsmod
Module                  Size  Used by
3dspusbbt              26925  0
bluetooth              65493  1 3dspusbbt
3dspusbbtpriv         576448  1 3dspusbbt
3dspusbwlan            35600  0
3dspusbwlanpriv       306854  1 3dspusbwlan
3dspusbbus             17659  2 3dspusbbt,3dspusbwlan
 

Kód: [Vybrat]

modinfo /usr/local/3DSP/usb/3dspusbwlan.ko
filename:       /usr/local/3DSP/usb/3dspusbwlan.ko
description:    Tdsp Wireless NIC driver
license:        GPL
srcversion:     126906CAD18EBEC3987C13E
alias:          usb:v05E1p0100d*dc*dsc*dp*ic*isc*ip*  # tvoja id 05e1:100
depends:        3dspusbwlanpriv,3dspusbbus
vermagic:       2.6.38-11-generic SMP mod_unload modversions 686

[AllKalda]

Takže si nejprve uložím ten soubor z odkazu a poté v terminálu pojedu řádek po řádku?

[AllKalda]

Protože já se nedokážu dostat ani pře ten první odkaz .....

kalda@kalda-L70:~$ sudo aptitude install build-essential linux-headers-`uname -r`
[sudo] password for kalda:
sudo: aptitude: command not found
kalda@kalda-L70:~$

[AllKalda]

po instalaci mam toto okno....ale driver nic...

Kód: [Vybrat]

kalda@kalda-L70:~$ $ git clone http://github.com/reyiyo/3dsp.git
$: command not found
kalda@kalda-L70:~$ git clone http://github.com/reyiyo/3dsp.git
Program 'git' není v současné době nainstalován.  Můžete jej nainstalovat napsáním:
sudo apt-get install git
kalda@kalda-L70:~$ sudo apt-get install git
[sudo] password for kalda:
Čtu seznamy balíků… Hotovo
Vytvářím strom závislostí       
Čtu stavové informace… Hotovo
Následující extra balíky budou instalovány:
  emacsen-common git-man liberror-perl
Navrhované balíky:
  git-doc git-el git-arch git-cvs git-svn git-email git-daemon-run git-gui
  gitk gitweb
Následující NOVÉ balíky budou nainstalovány:
  emacsen-common git git-man liberror-perl
0 aktualizováno, 4 nově instalováno, 0 k odstranění a 0 neaktualizováno.
Potřebuji stáhnout 4 804 kB archivů.
Po této operaci bude na disku použito dalších 11,4 MB.
Chcete pokračovat [Y/n]? y
Mám:1 http://cz.archive.ubuntu.com/ubuntu/ natty/main emacsen-common all 1.4.19ubuntu2 [17,7 kB]
Mám:2 http://cz.archive.ubuntu.com/ubuntu/ natty/main liberror-perl all 0.17-1 [23,8 kB]
Mám:3 http://cz.archive.ubuntu.com/ubuntu/ natty/main git-man all 1:1.7.4.1-3 [579 kB]
Mám:4 http://cz.archive.ubuntu.com/ubuntu/ natty/main git i386 1:1.7.4.1-3 [4 184 kB]
Staženo 4 804 kB za 1min 59s (40,4 kB/s)                                       
Instaluji balík emacsen-common.
(Čtu databázi … nyní je nainstalováno 167595 souborů a adresářů.)
Rozbaluji emacsen-common (z …/emacsen-common_1.4.19ubuntu2_all.deb) …
Instaluji balík liberror-perl.
Rozbaluji liberror-perl (z …/liberror-perl_0.17-1_all.deb) …
Instaluji balík git-man.
Rozbaluji git-man (z …/git-man_1%3a1.7.4.1-3_all.deb) …
Instaluji balík git.
Rozbaluji git (z …/git_1%3a1.7.4.1-3_i386.deb) …
Zpracování spouštěčů pro balík man-db …
Nastavuji balík emacsen-common (1.4.19ubuntu2) …
emacsen-common: Handling install of emacsen flavor emacs
Nastavuji balík liberror-perl (0.17-1) …
Nastavuji balík git-man (1:1.7.4.1-3) …
Nastavuji balík git (1:1.7.4.1-3) …
kalda@kalda-L70:~$ git clone http://github.com/reyiyo/3dsp.git
Cloning into 3dsp...
remote: Counting objects: 355, done.
remote: Compressing objects: 100% (244/244), done.
remote: Total 355 (delta 119), reused 330 (delta 103)
Receiving objects: 100% (355/355), 6.38 MiB | 30 KiB/s, done.
Resolving deltas: 100% (119/119), done.
kalda@kalda-L70:~$ cd 3dsp
kalda@kalda-L70:~/3dsp$ sudo bash Install_3DSPUSB.sh
 * Compiling the drivers, it will take some minutes...
 * Installing the drivers...
 * Installing the WB and wbtool...
 * Installing the 3dsp-wifi-radar...
 * Creating the init scripts...
 * Loading the modules...

_{//výpisy dávejte do #code}

[AllKalda]

Po instalaci a následném restartu se mi rozjelo Bluetooth, které sice pro mě není až tak podstatné, ale aspoň nějaký posun kupředu. Bohužel WiFi stále nejede....

[petertomasy]

super , si fakt dobrý, ale teraz by to chcelo , nejaké výpisy.

Kód: [Vybrat]

lsmod
ifconfig
iwconfig
nm-tool
dmesg # výpis bude fakt dlhý
rfkill all výpisy daj do "vložiť kód"  #

[AllKalda]

OK, jdu na to

[AllKalda]

Kód: [Vybrat]

kalda@kalda-L70:~$ lsmod
Module                  Size  Used by
nls_iso8859_1          12617  0
nls_cp437              12751  0
vfat                   17335  0
fat                    55505  1 vfat
usb_storage            43946  0
uas                    17676  0
rfcomm                 38125  10
sco                    17827  2
bnep                   17785  2
l2cap                  48656  16 rfcomm,bnep
parport_pc             32111  0
ppdev                  12849  0
snd_hda_codec_realtek   255882  1
3dspusbbt              26925  2
3dspusbbtpriv         576448  1 3dspusbbt
3dspusbwlan            35600  0
3dspusbwlanpriv       306854  1 3dspusbwlan
3dspusbbus             17659  2 3dspusbbt,3dspusbwlan
snd_hda_intel          24113  4
snd_hda_codec          90901  2 snd_hda_codec_realtek,snd_hda_intel
bluetooth              65493  9 rfcomm,sco,bnep,l2cap,3dspusbbt
snd_hwdep              13274  1 snd_hda_codec
snd_pcm                80042  3 snd_hda_intel,snd_hda_codec
snd_seq_midi           13132  0
i915                  451033  3
binfmt_misc            13213  1
joydev                 17322  0
snd_rawmidi            25269  1 snd_seq_midi
snd_seq_midi_event     14475  1 snd_seq_midi
snd_seq                51291  2 snd_seq_midi,snd_seq_midi_event
usbhid                 41704  0
drm_kms_helper         40745  1 i915
uvcvideo               66851  0
snd_timer              28659  2 snd_pcm,snd_seq
hid                    77084  1 usbhid
drm                   184164  4 i915,drm_kms_helper
psmouse                73312  0
snd_seq_device         14110  3 snd_seq_midi,snd_rawmidi,snd_seq
videodev               75143  1 uvcvideo
serio_raw              12990  0
snd                    55295  16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_algo_bit           13184  1 i915
soundcore              12600  1 snd
video                  18951  1 i915
snd_page_alloc         14073  2 snd_hda_intel,snd_pcm
lp                     13349  0
parport                36746  3 parport_pc,ppdev,lp
r8169                  42534  0


[AllKalda]

Kód: [Vybrat]

kalda@kalda-L70:~$ ifconfig
eth0      Link encap:Ethernet  HWadr 00:e0:4c:12:3c:63 
          inet adr:10.0.0.2  Všesměr:10.0.0.255  Maska:255.255.255.0
          inet6-adr: fe80::2e0:4cff:fe12:3c63/64 Rozsah:Linka
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:1496 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1634 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 783676 (783.6 KB) Odesláno bajtů: 305723 (305.7 KB)
          Přerušení:41

lo        Link encap:Místní smyčka 
          inet adr:127.0.0.1  Maska:255.0.0.0
          inet6-adr: ::1/128 Rozsah:Počítač
          AKTIVOVÁNO SMYČKA BĚŽÍ  MTU:16436  Metrika:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 480 (480.0 B) Odesláno bajtů: 480 (480.0 B)


[AllKalda]

Kód: [Vybrat]

kalda@kalda-L70:~$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

twifiu0   802.11 g  ESSID:off/any  Nickname:""
          NWID:off/any  Mode:Managed  Frequency=2.462 GHz 
          Access Point: Invalid   Bit Rate:11 Mb/s   
          Retry:on   RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality=0/100  Signal level=0 dBm  Noise level=0 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0


[petertomasy]

no a ako tak čítam README tak sa nainštaloval soft priamo pre kartu . Cesta b ymala byť  asi  :

Starting uWB
============

   Applications -> Accessories -> 3DSP uWB


Starting 3DSP WiFi Radar
========================

   Applications -> Accessories -> 3DSP WiFi Radar

teda v slovenčine: alplikacie >príslišenstvo >3DSP uWB    #, týmto by sa mala zapínať a vypínať wifi
                                   alplikacie >príslišenstvo>3DSP WiFi Radar  #,hladanie siete

[AllKalda]

Kód: [Vybrat]

kalda@kalda-L70:~$ nm-tool

NetworkManager Tool

State: connected

- Device: eth0  [Auto eth0] ----------------------------------------------------
  Type:              Wired
  Driver:            r8169
  State:             connected
  Default:           yes
  HW Address:        00:E0:4C:12:3C:63

  Capabilities:
    Carrier Detect:  yes
    Speed:           100 Mb/s

  Wired Properties
    Carrier:         on

  IPv4 Settings:
    Address:         10.0.0.2
    Prefix:          24 (255.255.255.0)
    Gateway:         10.0.0.138

    DNS:             10.0.0.138


[AllKalda]

Kód: [Vybrat]

r 1
[    1.128102] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    1.128124] ehci_hcd 0000:00:1d.7: debug port 1
[    1.132035] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    1.132072] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0444000
[    1.144034] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.144385] hub 1-0:1.0: USB hub found
[    1.144397] hub 1-0:1.0: 8 ports detected
[    1.144584] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.144626] uhci_hcd: USB Universal Host Controller Interface driver
[    1.144706] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.144722] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.144730] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.144854] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.144955] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[    1.145287] hub 2-0:1.0: USB hub found
[    1.145299] hub 2-0:1.0: 2 ports detected
[    1.145450] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.145466] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.145473] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.145575] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.145668] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[    1.145996] hub 3-0:1.0: USB hub found
[    1.146008] hub 3-0:1.0: 2 ports detected
[    1.146170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.146184] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.146192] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.146294] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.148118] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[    1.148434] hub 4-0:1.0: USB hub found
[    1.148459] hub 4-0:1.0: 2 ports detected
[    1.148624] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    1.148639] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.148647] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.148750] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.148866] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[    1.149179] hub 5-0:1.0: USB hub found
[    1.149190] hub 5-0:1.0: 2 ports detected
[    1.149463] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.174291] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.174308] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.174650] mousedev: PS/2 mouse device common for all mice
[    1.177146] rtc_cmos 00:08: RTC can wake from S4
[    1.177311] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[    1.177357] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.177609] device-mapper: uevent: version 1.0.3
[    1.177834] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com
[    1.178026] device-mapper: multipath: version 1.2.0 loaded
[    1.178035] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.178265] EISA: Probing bus 0 at eisa.0
[    1.178272] EISA: Cannot allocate resource for mainboard
[    1.178278] Cannot allocate resource for EISA slot 1
[    1.178284] Cannot allocate resource for EISA slot 2
[    1.178289] Cannot allocate resource for EISA slot 3
[    1.178295] Cannot allocate resource for EISA slot 4
[    1.178300] Cannot allocate resource for EISA slot 5
[    1.178305] Cannot allocate resource for EISA slot 6
[    1.178311] Cannot allocate resource for EISA slot 7
[    1.178316] Cannot allocate resource for EISA slot 8
[    1.178321] EISA: Detected 0 cards.
[    1.178563] cpuidle: using governor ladder
[    1.178711] cpuidle: using governor menu
[    1.179394] TCP cubic registered
[    1.179761] NET: Registered protocol family 10
[    1.181110] NET: Registered protocol family 17
[    1.181160] Registering the dns_resolver key type
[    1.182043] Using IPI No-Shortcut mode
[    1.182325] PM: Hibernation image not present or could not be loaded.
[    1.182350] registered taskstats version 1
[    1.182845]   Magic number: 15:820:688
[    1.183005] rtc_cmos 00:08: setting system clock to 2011-10-01 15:39:57 UTC (1317483597)
[    1.183012] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.183017] EDD information not available.
[    1.193173] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    1.283887] ata3.00: ATA-8: WDC WD3200BEVT-22A23T0, 01.01A01, max UDMA/133
[    1.283896] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.300497] ata3.00: configured for UDMA/133
[    1.300783] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200BEVT-2 01.0 PQ: 0 ANSI: 5
[    1.301133] sd 2:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.301259] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    1.301383] sd 2:0:0:0: [sda] Write Protect is off
[    1.301394] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.301508] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.335350]  sda: sda1 sda2 < sda5 >
[    1.336259] sd 2:0:0:0: [sda] Attached SCSI disk
[    1.336317] Freeing unused kernel memory: 700k freed
[    1.336937] Write protecting the kernel text: 5192k
[    1.337027] Write protecting the kernel read-only data: 2148k
[    1.386365] <30>udev[69]: starting version 167
[    1.456089] usb 1-3: new high speed USB device using ehci_hcd and address 2
[    1.664124] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.664217] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.664294] r8169 0000:02:00.0: setting latency timer to 64
[    1.664405] r8169 0000:02:00.0: irq 41 for MSI/MSI-X
[    1.666046] r8169 0000:02:00.0: eth0: RTL8102e at 0xf8020000, 00:e0:4c:12:3c:63, XID 14a00000 IRQ 41
[    1.808141] usb 1-5: new high speed USB device using ehci_hcd and address 3
[    1.992470] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    2.376062] usb 4-2: new low speed USB device using uhci_hcd and address 2
[   12.529241] Adding 2086908k swap on /dev/sda5.  Priority:-1 extents:1 across:2086908k
[   12.580188] <30>udev[271]: starting version 167
[   12.684883] lp: driver loaded but no devices found
[   12.729751] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   13.099510] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[   13.120349] acpi device:05: registered as cooling_device2
[   13.120640] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5
[   13.120844] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   13.262234] type=1400 audit(1317483609.574:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=468 comm="apparmor_parser"
[   13.263344] type=1400 audit(1317483609.574:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=468 comm="apparmor_parser"
[   13.264150] type=1400 audit(1317483609.578:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=468 comm="apparmor_parser"
[   13.587304] intel_rng: FWH not detected
[   13.739487] leds_ss4200: no LED devices found
[   13.891897] r8169 0000:02:00.0: eth0: link down
[   13.891911] r8169 0000:02:00.0: eth0: link down
[   13.893013] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   13.934787] Linux video capture interface: v2.00
[   14.106207] [drm] Initialized drm 1.1.0 20060810
[   14.375401] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (18e3:9512)
[   14.416815] psmouse serio1: ID: 10 00 64
[   14.461116] type=1400 audit(1317483610.774:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=612 comm="apparmor_parser"
[   14.466051] type=1400 audit(1317483610.778:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=613 comm="apparmor_parser"
[   14.467218] type=1400 audit(1317483610.778:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=613 comm="apparmor_parser"
[   14.467978] type=1400 audit(1317483610.778:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=613 comm="apparmor_parser"
[   14.485736] usbcore: registered new interface driver uvcvideo
[   14.485745] USB Video Class driver (v1.0.0)
[   14.560675] type=1400 audit(1317483610.874:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=616 comm="apparmor_parser"
[   14.562047] type=1400 audit(1317483610.874:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=616 comm="apparmor_parser"
[   14.571834] type=1400 audit(1317483610.882:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=621 comm="apparmor_parser"
[   14.723170] input: Genius 2.4G Wireless Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input6
[   14.733833] generic-usb 0003:0458:00B4.0001: input,hidraw0: USB HID v1.00 Mouse [Genius 2.4G Wireless Mouse] on usb-0000:00:1d.2-2/input0
[   14.733901] usbcore: registered new interface driver usbhid
[   14.733908] usbhid: USB HID core driver
[   14.747946] Finger Sensing Pad, hw: 12.1.1, sw: 1.0.0-K, buttons: 4
[   15.396352] input: FSPPS/2 Sentelic FingerSensingPad as /devices/platform/i8042/serio1/input/input7
[   15.436659] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   15.436676] i915 0000:00:02.0: setting latency timer to 64
[   15.508796] r8169 0000:02:00.0: eth0: link up
[   15.521072] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.553721] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   15.553731] [drm] Driver supports precise vblank timestamp query.
[   15.639897] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   15.640737] [drm] initialized overlay support
[   15.660130] Bluetooth: Core ver 2.15
[   15.660241] NET: Registered protocol family 31
[   15.660248] Bluetooth: HCI device and connection manager initialized
[   15.660256] Bluetooth: HCI socket layer initialized
[   15.755735]
[   15.755743] **************                                *******************
[   15.755749] **************        3DSP BUS Driver         *******************
[   15.755755] **************                                *******************
[   15.755761]
[   15.755765] tdspbus_init_module() enter!
[   15.755770] 3DSP USB Bus Driver   Build 17:09:59, Oct  1 2011
[   15.755776]    Version : BusU090716
[   15.755781]
[   15.755793] tdspbus_init_module() exit,ret=0!
[   15.773122] 3dspusbwlanpriv: module license 'Proprietary' taints kernel.
[   15.773132] Disabling lock debugging due to kernel taint
[   15.821501] Enter [_wlan_usb_probe]
[   15.821512] 3dsp usb wlan device found:) intf 0, alt configs 1, endpoints 5
[   15.821520] ep addr 1, type 2, in/out  IN
[   15.821526] ep addr 2, type 2, in/out OUT
[   15.821532] ep addr 3, type 2, in/out  IN
[   15.821538] ep addr 4, type 2, in/out OUT
[   15.821543] ep addr 9, type 3, in/out  IN
[   15.821549] tdsp_spin_lock_init is f834c280,syscall's is f834c280
[   15.821555] sc is f8352280
[   15.821560] usb_info is f2319e13
[   15.821566] 3D[T:WMAIN:01069][Adap_Create]  dsp Initialize start...!
[   15.821575] 3D[T:WMAIN:01075]Adap_Create usbinfo is f2319e13,EP_control is 0,EP_bulkout_HEAD is 4!
[   15.821595] WLAN: Bus_new_interface:  dev = f1c48000, intf = f233d300;
[   15.821605] WLAN: Bus_openInterface:  enter;
[   15.821613] register_tdspbus_usbdev be called,SerialNo = 2,version=WLU100811!
[   15.821617]
[   15.821625] Exit register_tdspbus_usbdev with success, SerialNo = 2!state_old_from_wb = 0, devstate = 0 ParaFlag = 0
[   15.821630]
[   15.821635] Leave [_wlan_usb_probe]
[   15.821659] Enter [_wlan_usb_probe]
[   15.821665] intf 1 is not 3dsp wlan interface
[   15.821858] usbcore: registered new interface driver 3DSP_WLAN_USB
[   15.935197] _bluetooth_usb_probe: ep addr 5, type 2, in/out  IN
[   15.935206] _bluetooth_usb_probe: ep addr 6, type 2, in/out OUT
[   15.935214] _bluetooth_usb_probe: ep addr 7, type 2, in/out  IN
[   15.935221] _bluetooth_usb_probe: ep addr 8, type 2, in/out OUT
[   15.935227] _bluetooth_usb_probe: ep addr 10, type 3, in/out  IN
[   15.935234] _bluetooth_usb_probe: sc is f829c2a0
[   15.935240] _bluetooth_usb_probe: usb_info is f2319e08
[   15.935265] BLUETOOTH: Bus_new_interface:  enter, dev = f26e6000, intf = f233de00;
[   15.935277] register_tdspbus_usbdev be called,SerialNo = 1,version=BTU100723!
[   15.935281]
[   15.935289] Exit register_tdspbus_usbdev with success, SerialNo = 1!state_old_from_wb = 0, devstate = 0 ParaFlag = 0
[   15.935294]
[   15.937850] usbcore: registered new interface driver 3DSP_BLUETOOTH_USB
[   16.025750] fbcon: inteldrmfb (fb0) is primary device
[   16.026120] Console: switching to colour frame buffer device 160x50
[   16.026233] fb0: inteldrmfb frame buffer device
[   16.026240] drm: registered panic notifier
[   16.026682] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[   16.027388] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   16.027505] HDA Intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[   16.027568] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   16.197914] hda_codec: ALC662 rev1: BIOS auto-probing.
[   16.215009] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   16.556399] ppdev: user-space parallel port driver
[   18.042082] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   24.697753] tdspbus_unlocked_ioctl cmd = 29
[   24.697764] ---tdspbus_unlocked_ioctl():671
[   24.697767]     enum mode is 4294967295
[   24.697854] tdspbus_unlocked_ioctl cmd = 30
[   24.697862] ---tdspbus_unlocked_ioctl():528
[   24.697865]     hotkey_flag is 0
[   24.697873] SerialNo=1 ParaFlag=0
[   24.697878] SerialNo=2 ParaFlag=0
[   24.704234] tdspbus_unlocked_ioctl cmd = 32
[   24.704244] ---tdspbus_unlocked_ioctl():554
[   24.704248]     antenna_flag is 0
[   24.704256] SerialNo=2 ParaFlag=0
[   24.924511] tdspbus_unlocked_ioctl cmd = 2a
[   24.924522] ---tdspbus_unlocked_ioctl():714
[   24.924526]     enum mode is 3
[   24.924559] ---tdspbus_unlocked_ioctl():285
[   24.924563]     tdspbus_unlocked_ioctl cmd = 0
[   25.340151] ---tdspbus_unlocked_ioctl():144
[   25.340156]     3DSP Bus Driver PlugIn called!
[   25.340167] Bus_PlugInDevice():79 trace! 2
[   25.340174] WLAN: Bus_Open:  enter;
[   25.340185] 3D[T:WMAIN:01115][Adap_Initialize]  dsp Initialize start,bus inf is f233d300...!
[   25.340197] 3D[T:USBDV:00697]Enter [UsbDev_Init]
[   25.340208] 3D[T:USBDV:00349]Enter [_UsbDev_Create_Usb]
[   25.340228] 3D[T:USBDV:00393]Leave [_UsbDev_Create_Usb] Success
[   25.340241] 3D[T:USBDV:00733]Leave [UsbDev_Init]
[   25.340249] 3D[T:WMAIN:01118]pAdap=f1c48000, pAdap->usb_context=f16860c0
[   25.340269] 3D[T:WMAIN:01984]ETSI
[   25.340277] 3D[T:WTASK:00066]Task_Init pAdap = f1c48000
[   25.340286] 3D[T:WTASK:00076]Task_Init: pTask memory alloc success!
[   25.340299] 3D[T:WTASK:00103]Task_Init: pTaskBlock memory alloc success!
[   25.340320] 3D[T:WTASK:00140]task free pool list count = 96
[   25.340328] 3D[T:WTASK:00142]task list count = 0
[   25.340336] 3D[T:WTASK:00144]task list high count = 0
[   25.340345] 3D[T:WMAIN:01186]pAdap=f1c48000, pAdap->usb_context=f16860c0
[   25.340356] 3D[T:MNAGE:00233]Mng_Init
[   25.340569] 3D[T:INTRU:00050]Enter [Int_Init]
[   25.340580] 3D[T:RECEV:00136]Enter [Rx_init]
[   25.340647] 3D[T:TRANS:02181]Enter [Tx_Init]
[   25.340884] 3D[T:TRANS:00396][_tx_msdu_pool_init]: pool type is 0 ,node free is 64
[   25.340909] 3D[T:TRANS:00396][_tx_msdu_pool_init]: pool type is 1 ,node free is 12
[   25.340936] 3D[T:TRANS:00396][_tx_msdu_pool_init]: pool type is 0 ,node free is 4
[   25.340951] 3D[T:WMAIN:00618]Enter [Adap_StartDevice] ,bus inf is f233d300!
[   25.341163] 3D[T:VENDR:01977][Vcmd_8051fw_isWork]:reg 0x14 = 18
[   25.344049] 3D[T:WMAIN:03441]* * * * * Adap_UpdateMediaState, Disconnected
[   25.344060] 3D[T:WMAIN:03475]^^^^^^ROAMING_SUPPORT, Adap_UpdateMediaState, NdisMediaStateDisconnected
[   25.584042] eth0: no IPv6 routers present
[   25.862142] 3D[T:VENDR:02028]Get 8051 Version: 09090409
[   25.862520] 3D[T:WMAIN:00678][Adap_StartDevice] init process with 8051 running
[   25.862534] 3D[T:VENDR:02328]* * * * * Vcmd_Funciton_Req_JOIN cmd 13:0  0
[   25.873106] 3D[T:INTRU:00411][Int_Process] :*****Undefined int, type = e1, sub_type = d,offset = 0,result = 0 *****
[   25.889119] 3D[T:INTRU:00268][Int_Process]:* * * * * Dsp_Reset 8051 int
[   25.889133] 3D[T:INTRU:00277][Int_Process] :* * * * * Dsp_Reset 8051 int,SINGLE
[   25.889144] 3D[T:INTRU:00306][Int_Process] :****8051 in normal working mode****
[   25.889194] 3D[T:WMAIN:00706][Adap_StartDevice] join int returned
[   26.609528] 3D[T:INTRU:00160][Int_Process]: GET_8051VER int, type = 30, sub_type = 0,offset = 0,result = 9090409 *****
[   26.625550] 3D[T:WMAIN:00795][Adap_StartDevice]: chipID is 4!
[   26.776079] 3D[T:WMAIN:00816][Adap_StartDevice]: Start to download dsp firmwire !
[   26.776090] 3D[T:WMAIN:01841][Adap_ParseAndSetHotKey:] bus info is f233d300
[   26.776100] 3D[T:USBSC:00442][sc_bus_get_hkey_flag:] bus info is f233d300
[   26.776109] 3D[T:WMAIN:01849]Adap_ParseAndSetHotKey:    NOT Supported HotKey !   
[   26.776807] 3D[T:WMAIN:00171]PortStart=16 PortEnd=19
[   26.776817] 3D[T:WMAIN:00214]Minicard mode 300
[   26.776824] 3D[T:WMAIN:00245]Minicard mode  antenna_flag = 0 antenna_diversity = 1 0
[   26.776833] 3D[T:WMAIN:00249]load 3dspcode.bin
[   26.966182] 3D[T:WMAIN:06537]EXTEND DSP CODE MARK: 30545845
[   27.000163] 3D[T:WMAIN:06561]==== Support Card Types = 15 ====
[   27.000173] 3D[T:WMAIN:06562]   SubSysID     WlOnly     BTOnly    Combo
[   27.000181] 3D[T:WMAIN:06592]CardID_0100      -          -         -
[   27.000189] 3D[T:WMAIN:06586]CardID_0200      Y          Y         Y
[   27.000196] 3D[T:WMAIN:06592]CardID_0300      -          -         -
[   27.000203] 3D[T:WMAIN:06586]CardID_0500      Y          Y         Y
[   27.000210] 3D[T:WMAIN:06586]CardID_0800      Y          Y         Y
[   27.000218] 3D[T:WMAIN:06586]CardID_0900      Y          Y         Y
[   27.000225] 3D[T:WMAIN:06586]CardID_0A00      Y          Y         Y
[   27.000233] 3D[T:WMAIN:06571]CardID_1100      -          Y         -
[   27.000240] 3D[T:WMAIN:06592]CardID_1120      -          -         -
[   27.000247] 3D[T:WMAIN:06592]CardID_1150      -          -         -
[   27.000254] 3D[T:WMAIN:06592]CardID_1160      -          -         -
[   27.000262] 3D[T:WMAIN:06571]CardID_1200      -          Y         -
[   27.000269] 3D[T:WMAIN:06592]CardID_1260      -          -         -
[   27.000276] 3D[T:WMAIN:06571]CardID_1900      -          Y         -
[   27.000284] 3D[T:WMAIN:06586]CardID_2241      Y          Y         Y
[   27.000291] 3D[T:WMAIN:06596]==== Support Card Types End ====
[   27.000299] 3D[T:WMAIN:06643]  Download CardID 0300 CodeID:03000001
[   27.000306] 3D[T:WMAIN:06656]******Download Code : Offset=1BD30  Len=DF6C PortBase=16
[   27.015317] 3D[T:WMAIN:00290]Find DSP Code Port 16 size 0x40003D[T:WMAIN:00315]Download DSP: Port 16   size 0x4000 Dsp code
[   27.281821] 3D[T:WMAIN:00315]Download DSP: Port 17   size 0x27FC Dsp code
[   27.441902] 3D[T:WMAIN:00315]Download DSP: Port 18   size 0x3800 Dsp code
[   27.618033] 3D[T:WMAIN:00315]Download DSP: Port 19   size 0x3A40 Dsp code
[   27.874184] 3D[T:WMAIN:00346]Download DSP: Port 20   size 0x508  mini Dsp code
[   27.876621] 3D[T:WMAIN:00825][Adap_StartDevice]: Adap_GetDspFwCodesAndDownload Success!
[   27.906196] 3D[T:WMAIN:00844][Adap_StartDevice]: permanent_address=00:21:c5:18:0e:5b
[   27.906213] 3D[T:WMAIN:00854][Adap_StartDevice]: current_address=00:21:c5:18:0e:5b
[   28.005905] ACPI: EC: GPE storm detected, transactions will use polling mode
[   28.216096] 3D[T:VENDR:02867][Vcmd_mmacSp20ResetRemoved] Resetting SP20 in Vcmd_mmacSp20ResetRemoved
[   28.242347] 3D[T:VENDR:02746][Vcmd_CardBusNICStart] start card bus nic ok
[   28.291560] 3D[T:WMAIN:05096][Adap_w2lan_init] wlan_init phy mode = 2
[   28.308613] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   28.389369] 3D[T:WMAIN:00868][Adap_StartDevice]: Adap_WLSMAC_initialize Success!
[   28.508183] 3D[T:RECEV:00224]Enter [Rx_restart]
[   28.508204] 3D[T:WMAIN:00993][Adap_StartDevice]: init for usb 20 device
[   28.510536] 3D[T:WMAIN:01024][Adap_StartDevice]: Completed Init Successfully
[   28.510546] 3D[T:WMAIN:01028][Adap_StartDevice]: driver version = WL090120_2
[   28.510556] 3D[T:WMAIN:01033][Adap_StartDevice]: 8051 version = 09.09.04.09
[   28.510567] 3D[T:WMAIN:01038][Adap_StartDevice]: dsp version = 36.04.11.084
[   28.511536] 3D[T:VENDR:02097]****SWITCHING:*******8051 go main loop  ************ 
[   28.514422] 3D[T:INTRU:00411][Int_Process] :*****Undefined int, type = db, sub_type = 50,offset = 5000,result = 190002 *****
[   28.802574] 3D[T:INTRU:00324][Int_Process] :*****8051 in normal working mode****
[   28.808154] 3D[T:WMAIN:01051][Adap_StartDevice]: Vcmd_Set_Firmware_Download_Ok Successfully!
[   28.808580] 3D[T:WMAIN:01060][Adap_StartDevice]: Vcmd_Set_Encryption_Mode Successfully!
[   28.818773] [NETDV:00235] register netdev successfully
[   29.819217] tdspbus_unlocked_ioctl cmd = 20
[   29.819226] ---tdspbus_unlocked_ioctl():430
[   29.819230]     query_device_state serial no = 2, return value = 1
[   29.819260] tdspbus_unlocked_ioctl cmd = 10
[   29.819266] ---tdspbus_unlocked_ioctl():408
[   29.819268]     ---tdspbus_unlocked_ioctl():252
[   30.319441]     tdspbus_unlocked_ioctl cmd = 0
[   31.019725] ---tdspbus_unlocked_ioctl():144
[   31.019729]     3DSP Bus Driver PlugIn called!
[   31.019739] Bus_PlugInDevice():79 trace! 1
[   31.019745] BLUETOOTH: Bus_Open:  enter;
[   31.048071] OpenDev: start device process not completed
[   31.059698] 3D[T:INTRU:00268][Int_Process]:* * * * * Dsp_Reset 8051 int
[   31.059711] 3D[T:INTRU:00272][Int_Process] :* * * * * Dsp_Reset 8051 int,COMBO
[   31.059721] 3D[T:INTRU:00300][Int_Process] :* * * * * hardware reset task again
[   31.059787] 3D[T:WMAIN:02591]>>ENTER [Adap_HardwareReset] >>
[   31.075708] 3D[T:INTRU:00399][Int_Process] :****Undefined int, type = 33, sub_type = 0,offset = 0,result = 4 *****
[   32.064079] 3D[T:WMAIN:02578]CMD_GET_8051Status return 1
[   32.116132] [NETDV:00264] unregister netdev successfully
[   32.116150] 3D[T:TRANS:02730]Enter [Tx_Reset]
[   32.117364] 3D[T:VENDR:03525]Adap_Set_SoftReset 1
[   32.268098] 3D[T:RECEV:00205]Enter [Rx_stop]
[   32.268110] 3D[T:USBDV:01224]Enter [UsbDev_CancelBulkInTransfer]
[   32.268138] 3D[E:INTRU:00534][Int_SubmitInt]:  int transfer is working!
[   32.268360] 3D[E:USBDV:00612][_usb_complete_task] failed with urb status:-104 ,urb type is 4
[   32.412073] 3D[T:WMAIN:01841][Adap_ParseAndSetHotKey:] bus info is f233d300
[   32.412086] 3D[T:USBSC:00442][sc_bus_get_hkey_flag:] bus info is f233d300
[   32.412096] 3D[T:WMAIN:01849]Adap_ParseAndSetHotKey:    NOT Supported HotKey !   
[   32.412757] 3D[T:WMAIN:00171]PortStart=16 PortEnd=19
[   32.412769] 3D[T:WMAIN:00214]Minicard mode 300
[   32.412778] 3D[T:WMAIN:00245]Minicard mode  antenna_flag = 0 antenna_diversity = 1 0
[   32.412789] 3D[T:WMAIN:00249]load 3dspcode.bin
[   32.412842] 3D[T:WMAIN:06537]EXTEND DSP CODE MARK: 30545845
[   32.413116] 3D[T:WMAIN:06561]==== Support Card Types = 15 ====
[   32.413127] 3D[T:WMAIN:06562]   SubSysID     WlOnly     BTOnly    Combo
[   32.413137] 3D[T:WMAIN:06592]CardID_0100      -          -         -
[   32.413146] 3D[T:WMAIN:06586]CardID_0200      Y          Y         Y
[   32.413156] 3D[T:WMAIN:06592]CardID_0300      -          -         -
[   32.413166] 3D[T:WMAIN:06586]CardID_0500      Y          Y         Y
[   32.413175] 3D[T:WMAIN:06586]CardID_0800      Y          Y         Y
[   32.413184] 3D[T:WMAIN:06586]CardID_0900      Y          Y         Y
[   32.413193] 3D[T:WMAIN:06586]CardID_0A00      Y          Y         Y
[   32.413203] 3D[T:WMAIN:06571]CardID_1100      -          Y         -
[   32.413213] 3D[T:WMAIN:06592]CardID_1120      -          -         -
[   32.413222] 3D[T:WMAIN:06592]CardID_1150      -          -         -
[   32.413232] 3D[T:WMAIN:06592]CardID_1160      -          -         -
[   32.413242] 3D[T:WMAIN:06571]CardID_1200      -          Y         -
[   32.413251] 3D[T:WMAIN:06592]CardID_1260      -          -         -
[   32.413261] 3D[T:WMAIN:06571]CardID_1900      -          Y         -
[   32.413270] 3D[T:WMAIN:06586]CardID_2241      Y          Y         Y
[   32.413279] 3D[T:WMAIN:06596]==== Support Card Types End ====
[   32.413289] 3D[T:WMAIN:06643]  Download CardID 0300 CodeID:03000004
[   32.413299] 3D[T:WMAIN:06656]******Download Code : Offset=104370  Len=E50C PortBase=16
[   32.427415] 3D[T:WMAIN:00290]Find DSP Code Port 16 size 0x40003D[T:WMAIN:00315]Download DSP: Port 16   size 0x4000 Dsp code
[   32.692573] 3D[T:WMAIN:00315]Download DSP: Port 17   size 0x27FC Dsp code
[   32.868655] 3D[T:WMAIN:00315]Download DSP: Port 18   size 0x3800 Dsp code
[   33.028750] 3D[T:WMAIN:00315]Download DSP: Port 19   size 0x3A40 Dsp code
[   33.268865] 3D[T:WMAIN:00346]Download DSP: Port 20   size 0x508  mini Dsp code
[   33.271182] 3D[T:WMAIN:00375]Download DSP: Port 21   size 0x598 BT Dsp Parameter
[   33.280064] 3D[T:VENDR:02361]* * * * * Vcmd_Funciton_Set_BTPara_Ready
[   33.280439] 3D[T:WMAIN:00404]BT_PARAMETER_READY_0
[   33.284811] 3D[T:INTRU:00411][Int_Process] :*****Undefined int, type = 32, sub_type = 0,offset = 0,result = 1 *****
[   34.012048] 3D[T:VENDR:02867][Vcmd_mmacSp20ResetRemoved] Resetting SP20 in Vcmd_mmacSp20ResetRemoved
[   34.037207] 3D[T:VENDR:02746][Vcmd_CardBusNICStart] start card bus nic ok
[   34.086459] 3D[T:WMAIN:05096][Adap_w2lan_init] wlan_init phy mode = 2
[   34.744151] 3D[T:WTASK:00661]**Enter Task_RemoveAllMngFrameTask
[   34.744160] 3D[T:WTASK:00698]**Exit Task_RemoveAllMngFrameTask
[   34.744167] 3D[T:RECEV:00224]Enter [Rx_restart]
[   34.781059] 3D[T:VENDR:02097]****SWITCHING:*******8051 go main loop  ************ 
[   34.789557] 3D[T:INTRU:00411][Int_Process] :*****Undefined int, type = db, sub_type = 50,offset = 5000,result = 1190404 *****
[   35.077704] 3D[T:INTRU:00324][Int_Process] :*****8051 in normal working mode****
[   35.084111] [tdsp_netdev_netq_ifstop]: error:net dev is NULL
[   35.084132] 3D[T:WMAIN:02912]driver version = WL090120_2
[   35.084141] 3D[T:WMAIN:02915]8051 version = 09.09.04.09
[   35.084150] 3D[T:WMAIN:02918]dsp version = 36.04.11.081
[   35.084159] 3D[T:WMAIN:02940]<<EXIT [Adap_HardwareReset] <<
[   35.096147] [NETDV:00235] register netdev successfully
[   37.592108] OpenDev: Start Device Phase 2 Ok
[   37.810318] Bluetooth: L2CAP ver 2.15
[   37.810328] Bluetooth: L2CAP socket layer initialized
[   37.873011] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   37.873022] Bluetooth: BNEP filters: protocol multicast
[   37.901991] Bluetooth: SCO (Voice Link) ver 0.6
[   37.902000] Bluetooth: SCO socket layer initialized
[   38.065599] Bluetooth: RFCOMM TTY layer initialized
[   38.065616] Bluetooth: RFCOMM socket layer initialized
[   38.065623] Bluetooth: RFCOMM ver 1.11
[   40.982845] r8169 0000:02:00.0: eth0: link down
[   71.031469] r8169 0000:02:00.0: eth0: link up
[  470.964104] usb 1-1: new high speed USB device using ehci_hcd and address 5
[  471.218512] usbcore: registered new interface driver uas
[  471.256193] Initializing USB Mass Storage driver...
[  471.256767] scsi4 : usb-storage 1-1:1.0
[  471.257136] usbcore: registered new interface driver usb-storage
[  471.257144] USB Mass Storage support registered.
[  472.263025] scsi 4:0:0:0: Direct-Access     Sony     MSAC-UAM2        1.00 PQ: 0 ANSI: 0 CCS
[  472.266468] sd 4:0:0:0: Attached scsi generic sg1 type 0
[  473.222093] sd 4:0:0:0: [sdb] 15736832 512-byte logical blocks: (8.05 GB/7.50 GiB)
[  473.223063] sd 4:0:0:0: [sdb] Write Protect is off
[  473.223085] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[  473.223099] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  473.229076] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  473.232549]  sdb: sdb1
[  473.237340] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  473.237364] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[  558.772614] usb 1-1: USB disconnect, address 5
[ 1149.541238] _ioctl_iw_get_essid: =>
[ 1149.541249] _ioctl_iw_get_mode: mode = 1(INFRA)
[ 2268.756447] _ioctl_iw_get_essid: =>
[ 2268.756473] _ioctl_iw_get_mode: mode = 1(INFRA)

[AllKalda]

Kód: [Vybrat]

kalda@kalda-L70:~$ rfkill all
Usage: rfkill [options] command
Options:
--version show version (0.4-1 (Ubuntu))
Commands:
help
event
list [IDENTIFIER]
block IDENTIFIER
unblock IDENTIFIER
where IDENTIFIER is the index no. of an rfkill switch or one of:
<idx> all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm