Prosíme přihlašte se nebo zaregistrujte.

Přihlašte se svým uživatelským jménem a heslem.
Vaše pomoc je stále potřeba!

Autor Téma: Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...  (Přečteno 4126 krát)

Eran

  • Návštěvník
  • *
  • Příspěvků: 8
    • Zobrazit profil
Zdravím... možná je to pro vás otravné ale rád bych zprovoznil 3d akceleraci na ubuntu mám nejnovější staženou... když dám nainstalovat ovladače rafiky tak mě to háže že se stala chyba...
Může mi někdo poradit jak to rozchodit? 
rafiku mám ATI Radeon HD5470
jinak notebook HP G62
Budu rád za každou radu...
Zkoušel sjem i přes terminál podle návodu ale když otevřu xorg.conf  tak tam mám prázno ... oproti fotkám v návodu....
už nevím jak dál...
« Poslední změna: 04 Listopadu 2011, 18:58:07 od Eran »

Eran

  • Návštěvník
  • *
  • Příspěvků: 8
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #1 kdy: 04 Listopadu 2011, 19:03:18 »
Tak teĎ se mi povedlo konečně v dodatečných ovladačích nainstalovat a povolit  ovladače ale stále nevím jak onu 3d Akceleraci zapnout...  :'(

TIBOR

  • Guru
  • *****
  • Příspěvků: 6463
  • Som uzivatel linuxovej distribucie, som linuxak?
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #2 kdy: 04 Listopadu 2011, 19:12:12 »
Ak sa spravne nainstalovali ovladace tak by sa 3d akceleracia mala zapnut sama. Zkontrolovat si to mozes prikazom
Kód: [Vybrat]
glxinfo | grep directak vypise
Kód: [Vybrat]
direct rendering: Yestak 3d akceleracia ide.
Cerpane z
http://wiki.ubuntu.cz/Ovlada%C4%8De%20grafick%C3%BDch%20karet#Test_3D_akcelerace
HP Laptop 17-ca1xxx Ubuntu Mate 20.04.2 FF 64bit.
Asus X751LB-TY014H Ubuntu Mate 20.04.1 FF 64bit.
Linus, Lajnas, Línus, Luínus, Lajnus a je mi naozaj jedno, ako ľudia vyslovujú moje meno. Ale "Linux" je vždy "Linux". LINUS TORVALDS, tvorca Linuxového jadra.(V dokumente Revolution OS)

Eran

  • Návštěvník
  • *
  • Příspěvků: 8
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #3 kdy: 04 Listopadu 2011, 19:23:09 »
vyhodilo to error
X Error of failed request:  BadRequest (invalid request code or no such operation)
  Major opcode of failed request:  155 (GLX)
  Minor opcode of failed request:  19 (X_GLXQueryServerString)
  Serial number of failed request:  12
  Current serial number in output stream:  12



Ale stále v nastavení ovladaču  hlásíovladač je povolen a pracuje zprávně(FLRX od Ati/AMD)

sabraq

  • Závislák
  • ****
  • Příspěvků: 3395
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #4 kdy: 04 Listopadu 2011, 19:48:52 »
vyhodilo to error
X Error of failed request:  BadRequest (invalid request code or no such operation)
  Major opcode of failed request:  155 (GLX)
  Minor opcode of failed request:  19 (X_GLXQueryServerString)
  Serial number of failed request:  12
  Current serial number in output stream:  12



Ale stále v nastavení ovladaču  hlásíovladač je povolen a pracuje zprávně(FLRX od Ati/AMD)
Hm, tak sem dej do code obsah souboru /var/log/Xorg.0.log. Nebo ho přilož celý.
************************************

Eran

  • Návštěvník
  • *
  • Příspěvků: 8
    • Zobrazit profil

sabraq

  • Závislák
  • ****
  • Příspěvků: 3395
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #6 kdy: 04 Listopadu 2011, 20:16:39 »
tady je http://www.edisk.cz/stahni/78349/Xorg.0.log_33.04KB.html

díky za rady...
Hm, tak to bude problém, máš 2 grafiky a nahrává se ti intel ovladač:/. Zkus se podívat do Biosu, jestli se interní grafika nedá vypnout a nechat běžet jenom diskrétní - ale bude ti to víc žrát baterku. Jen tak ve stručnosti.Jinak na toto téma se toho na fóru napsalo nemálo, zkus pohledat problémy s grafikami.
************************************

sabraq

  • Závislák
  • ****
  • Příspěvků: 3395
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #7 kdy: 04 Listopadu 2011, 20:18:16 »
a vejde se:)
Kód: [Vybrat]
X.Org X Server 1.10.4
Release Date: 2011-08-19
[    15.605] X Protocol Version 11, Revision 0
[    15.605] Build Operating System: Linux 2.6.24-29-server x86_64 Ubuntu
[    15.605] Current Operating System: Linux michal-HP-G62-Notebook-PC 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC 2011 x86_64
[    15.605] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.0.0-12-generic root=UUID=7db8429d-85b6-48f0-8627-d42aff85211e ro quiet splash vt.handoff=7
[    15.605] Build Date: 19 October 2011  05:21:26AM
[    15.605] xorg-server 2:1.10.4-1ubuntu4.2 (For technical support please see http://www.ubuntu.com/support)
[    15.605] Current version of pixman: 0.22.2
[    15.605] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[    15.605] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    15.605] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Nov  4 19:00:20 2011
[    15.720] (==) Using config file: "/etc/X11/xorg.conf"
[    15.720] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    15.832] (==) No Layout section.  Using the first Screen section.
[    15.832] (**) |-->Screen "Default Screen" (0)
[    15.832] (**) |   |-->Monitor "<default monitor>"
[    15.832] (==) No monitor specified for screen "Default Screen".
Using a default monitor configuration.
[    15.832] (==) Automatically adding devices
[    15.832] (==) Automatically enabling devices
[    15.877] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    15.877] Entry deleted from font path.
[    15.877] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[    15.877] Entry deleted from font path.
[    15.877] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[    15.877] Entry deleted from font path.
[    15.883] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[    15.883] Entry deleted from font path.
[    15.883] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[    15.883] Entry deleted from font path.
[    15.907] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/Type1,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
[    15.907] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[    15.907] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[    15.907] (II) Loader magic: 0x7e0220
[    15.907] (II) Module ABI versions:
[    15.907] X.Org ANSI C Emulation: 0.4
[    15.907] X.Org Video Driver: 10.0
[    15.907] X.Org XInput driver : 12.3
[    15.907] X.Org Server Extension : 5.0
[    15.908] (--) PCI:*(0:0:2:0) 8086:0046:103c:143a rev 2, Mem @ 0xc0000000/4194304, 0xb0000000/268435456, I/O @ 0x00004050/8
[    15.908] (--) PCI: (0:1:0:0) 1002:68e0:103c:143a rev 0, Mem @ 0xa0000000/268435456, 0xc4400000/131072, I/O @ 0x00003000/256, BIOS @ 0x????????/131072
[    15.908] (II) Open ACPI successful (/var/run/acpid.socket)
[    15.908] (II) "extmod" will be loaded by default.
[    15.908] (II) "dbe" will be loaded by default.
[    15.908] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[    15.908] (II) "record" will be loaded by default.
[    15.908] (II) "dri" will be loaded by default.
[    15.908] (II) "dri2" will be loaded by default.
[    15.908] (II) LoadModule: "glx"
[    16.047] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so
[    16.119] (II) Module glx: vendor="FireGL - AMD Technologies Inc."
[    16.119] compiled for 6.9.0, module version = 1.0.0
[    16.120] (II) Loading extension GLX
[    16.120] (II) LoadModule: "extmod"
[    16.284] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[    16.316] (II) Module extmod: vendor="X.Org Foundation"
[    16.316] compiled for 1.10.4, module version = 1.0.0
[    16.316] Module class: X.Org Server Extension
[    16.316] ABI class: X.Org Server Extension, version 5.0
[    16.316] (II) Loading extension MIT-SCREEN-SAVER
[    16.316] (II) Loading extension XFree86-VidModeExtension
[    16.316] (II) Loading extension XFree86-DGA
[    16.316] (II) Loading extension DPMS
[    16.316] (II) Loading extension XVideo
[    16.316] (II) Loading extension XVideo-MotionCompensation
[    16.316] (II) Loading extension X-Resource
[    16.316] (II) LoadModule: "dbe"
[    16.316] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[    16.452] (II) Module dbe: vendor="X.Org Foundation"
[    16.452] compiled for 1.10.4, module version = 1.0.0
[    16.452] Module class: X.Org Server Extension
[    16.452] ABI class: X.Org Server Extension, version 5.0
[    16.452] (II) Loading extension DOUBLE-BUFFER
[    16.452] (II) LoadModule: "record"
[    16.452] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    16.481] (II) Module record: vendor="X.Org Foundation"
[    16.481] compiled for 1.10.4, module version = 1.13.0
[    16.481] Module class: X.Org Server Extension
[    16.481] ABI class: X.Org Server Extension, version 5.0
[    16.482] (II) Loading extension RECORD
[    16.482] (II) LoadModule: "dri"
[    16.482] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    16.598] (II) Module dri: vendor="X.Org Foundation"
[    16.598] compiled for 1.10.4, module version = 1.0.0
[    16.598] ABI class: X.Org Server Extension, version 5.0
[    16.598] (II) Loading extension XFree86-DRI
[    16.598] (II) LoadModule: "dri2"
[    16.598] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    16.619] (II) Module dri2: vendor="X.Org Foundation"
[    16.619] compiled for 1.10.4, module version = 1.2.0
[    16.619] ABI class: X.Org Server Extension, version 5.0
[    16.619] (II) Loading extension DRI2
[    16.619] (==) Matched intel as autoconfigured driver 0
[    16.619] (==) Matched vesa as autoconfigured driver 1
[    16.619] (==) Matched fbdev as autoconfigured driver 2
[    16.619] (==) Assigned the driver to the xf86ConfigLayout
[    16.619] (II) LoadModule: "intel"
[    16.619] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    16.730] (II) Module intel: vendor="X.Org Foundation"
[    16.731] compiled for 1.10.2.902, module version = 2.15.901
[    16.731] Module class: X.Org Video Driver
[    16.731] ABI class: X.Org Video Driver, version 10.0
[    16.731] (II) LoadModule: "vesa"
[    16.731] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    16.774] (II) Module vesa: vendor="X.Org Foundation"
[    16.774] compiled for 1.10.2, module version = 2.3.0
[    16.774] Module class: X.Org Video Driver
[    16.774] ABI class: X.Org Video Driver, version 10.0
[    16.774] (II) LoadModule: "fbdev"
[    16.774] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    16.813] (II) Module fbdev: vendor="X.Org Foundation"
[    16.813] compiled for 1.10.0, module version = 0.4.2
[    16.813] ABI class: X.Org Video Driver, version 10.0
[    16.813] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
[    16.814] (II) VESA: driver for VESA chipsets: vesa
[    16.814] (II) FBDEV: driver for framebuffer: fbdev
[    16.814] (++) using VT number 7

[    16.815] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    16.815] (WW) Falling back to old probe method for vesa
[    16.815] (WW) Falling back to old probe method for fbdev
[    16.815] (II) Loading sub module "fbdevhw"
[    16.815] (II) LoadModule: "fbdevhw"
[    16.816] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    16.847] (II) Module fbdevhw: vendor="X.Org Foundation"
[    16.847] compiled for 1.10.4, module version = 0.0.2
[    16.847] ABI class: X.Org Video Driver, version 10.0
[    16.848] drmOpenDevice: node name is /dev/dri/card0
[    16.848] drmOpenDevice: open result is 12, (OK)
[    16.848] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[    16.848] drmOpenDevice: node name is /dev/dri/card0
[    16.848] drmOpenDevice: open result is 12, (OK)
[    16.848] drmOpenByBusid: drmOpenMinor returns 12
[    16.848] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[    16.848] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen" for depth/fbbpp 24/32
[    16.848] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[    16.848] (==) intel(0): RGB weight 888
[    16.848] (==) intel(0): Default visual is TrueColor
[    16.848] (II) intel(0): Integrated Graphics Chipset: Intel(R) Arrandale
[    16.848] (--) intel(0): Chipset: "Arrandale"
[    16.848] (**) intel(0): Relaxed fencing enabled
[    16.848] (**) intel(0): Wait on SwapBuffers? enabled
[    16.848] (**) intel(0): Triple buffering? enabled
[    16.848] (**) intel(0): Framebuffer tiled
[    16.848] (**) intel(0): Pixmaps tiled
[    16.848] (**) intel(0): 3D buffers tiled
[    16.848] (**) intel(0): SwapBuffers wait enabled
[    16.848] (==) intel(0): video overlay key set to 0x101fe
[    16.848] (II) intel(0): Output LVDS1 has no monitor section
[    16.848] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video1
[    16.848] (II) intel(0): Output VGA1 has no monitor section
[    16.848] (II) intel(0): EDID for output LVDS1
[    16.848] (II) intel(0): Manufacturer: CMO  Model: 1592  Serial#: 0
[    16.848] (II) intel(0): Year: 2009  Week: 53
[    16.848] (II) intel(0): EDID Version: 1.3
[    16.848] (II) intel(0): Digital Display Input
[    16.848] (II) intel(0): Max Image Size [cm]: horiz.: 35  vert.: 19
[    16.848] (II) intel(0): Gamma: 2.20
[    16.848] (II) intel(0): No DPMS capabilities specified
[    16.848] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[    16.848] (II) intel(0): First detailed timing is preferred mode
[    16.848] (II) intel(0): redX: 0.602 redY: 0.340   greenX: 0.306 greenY: 0.530
[    16.848] (II) intel(0): blueX: 0.151 blueY: 0.120   whiteX: 0.313 whiteY: 0.329
[    16.848] (II) intel(0): Manufacturer's mask: 0
[    16.848] (II) intel(0): Supported detailed timing:
[    16.848] (II) intel(0): clock: 69.3 MHz   Image Size:  344 x 193 mm
[    16.848] (II) intel(0): h_active: 1366  h_sync: 1382  h_sync_end 1416 h_blank_end 1466 h_border: 0
[    16.848] (II) intel(0): v_active: 768  v_sync: 770  v_sync_end 776 v_blanking: 788 v_border: 0
[    16.848] (II) intel(0):  N156B6-L0B
[    16.848] (II) intel(0):  CMO
[    16.848] (II) intel(0):  N156B6-L0B
[    16.848] (II) intel(0): EDID (in hex):
[    16.848] (II) intel(0): 00ffffffffffff000daf921500000000
[    16.848] (II) intel(0): 35130103802313780a07f59a574e8726
[    16.848] (II) intel(0): 1e505400000001010101010101010101
[    16.848] (II) intel(0): 010101010101121b5664500014301022
[    16.848] (II) intel(0): 260058c110000018000000fe004e3135
[    16.848] (II) intel(0): 3642362d4c30420a2020000000fe0043
[    16.848] (II) intel(0): 4d4f0a202020202020202020000000fe
[    16.848] (II) intel(0): 004e31353642362d4c30420a20200020
[    16.848] (II) intel(0): EDID vendor "CMO", prod id 5522
[    16.848] (II) intel(0): Printing DDC gathered Modelines:
[    16.848] (II) intel(0): Modeline "1366x768"x0.0   69.30  1366 1382 1416 1466  768 770 776 788 -hsync -vsync (47.3 kHz)
[    16.848] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[    16.848] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[    16.849] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[    16.849] (II) intel(0): Printing probed modes for output LVDS1
[    16.849] (II) intel(0): Modeline "1366x768"x60.0   69.30  1366 1382 1416 1466  768 770 776 788 -hsync -vsync (47.3 kHz)
[    16.849] (II) intel(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz)
[    16.849] (II) intel(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz)
[    16.849] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[    16.849] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[    16.849] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
[    16.849] (II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
[    16.849] (II) intel(0): EDID for output VGA1
[    16.849] (II) intel(0): Output LVDS1 connected
[    16.849] (II) intel(0): Output VGA1 disconnected
[    16.849] (II) intel(0): Using exact sizes for initial modes
[    16.849] (II) intel(0): Output LVDS1 using initial mode 1366x768
[    16.849] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    16.849] (II) intel(0): Kernel page flipping support detected, enabling
[    16.849] (**) intel(0): Display dimensions: (350, 190) mm
[    16.849] (**) intel(0): DPI set to (99, 102)
[    16.849] (II) Loading sub module "fb"
[    16.849] (II) LoadModule: "fb"
[    16.849] (II) Loading /usr/lib/xorg/modules/libfb.so
[    16.872] (II) Module fb: vendor="X.Org Foundation"
[    16.872] compiled for 1.10.4, module version = 1.0.0
[    16.872] ABI class: X.Org ANSI C Emulation, version 0.4
[    16.872] (II) Loading sub module "dri2"
[    16.872] (II) LoadModule: "dri2"
[    16.872] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    16.872] (II) Module dri2: vendor="X.Org Foundation"
[    16.872] compiled for 1.10.4, module version = 1.2.0
[    16.872] ABI class: X.Org Server Extension, version 5.0
[    16.872] (II) UnloadModule: "vesa"
[    16.872] (II) Unloading vesa
[    16.872] (II) UnloadModule: "fbdev"
[    16.872] (II) Unloading fbdev
[    16.873] (II) UnloadModule: "fbdevhw"
[    16.873] (II) Unloading fbdevhw
[    16.873] (==) Depth 24 pixmap format is 32 bpp
[    16.873] (II) intel(0): [DRI2] Setup complete
[    16.873] (II) intel(0): [DRI2]   DRI driver: i965
[    16.873] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[    16.900] (II) UXA(0): Driver registered support for the following operations:
[    16.900] (II)         solid
[    16.900] (II)         copy
[    16.900] (II)         composite (RENDER acceleration)
[    16.900] (II)         put_image
[    16.900] (II)         get_image
[    16.900] (==) intel(0): Backing store disabled
[    16.900] (==) intel(0): Silken mouse enabled
[    16.901] (II) intel(0): Initializing HW Cursor
[    16.968] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    16.968] (==) intel(0): DPMS enabled
[    16.968] (==) intel(0): Intel XvMC decoder enabled
[    16.968] (II) intel(0): Set up textured video
[    16.968] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[    16.968] (II) intel(0): direct rendering: DRI2 Enabled
[    16.968] (==) intel(0): hotplug detection: "enabled"
[    16.968] (--) RandR disabled
[    16.968] (II) Initializing built-in extension Generic Event Extension
[    16.968] (II) Initializing built-in extension SHAPE
[    16.968] (II) Initializing built-in extension MIT-SHM
[    16.968] (II) Initializing built-in extension XInputExtension
[    16.968] (II) Initializing built-in extension XTEST
[    16.968] (II) Initializing built-in extension BIG-REQUESTS
[    16.968] (II) Initializing built-in extension SYNC
[    16.968] (II) Initializing built-in extension XKEYBOARD
[    16.968] (II) Initializing built-in extension XC-MISC
[    16.968] (II) Initializing built-in extension SECURITY
[    16.968] (II) Initializing built-in extension XINERAMA
[    16.968] (II) Initializing built-in extension XFIXES
[    16.968] (II) Initializing built-in extension RENDER
[    16.968] (II) Initializing built-in extension RANDR
[    16.968] (II) Initializing built-in extension COMPOSITE
[    16.968] (II) Initializing built-in extension DAMAGE
[    16.968] (II) Initializing built-in extension GESTURE
[    16.975] (EE) GLX error: Can not get required symbols.
[    16.975] (II) intel(0): Setting screen physical size to 361 x 203
[    17.068] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[    17.190] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    17.190] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    17.190] (II) LoadModule: "evdev"
[    17.190] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.285] (II) Module evdev: vendor="X.Org Foundation"
[    17.285] compiled for 1.10.2, module version = 2.6.0
[    17.285] Module class: X.Org XInput Driver
[    17.285] ABI class: X.Org XInput driver, version 12.3
[    17.285] (II) Using input driver 'evdev' for 'Power Button'
[    17.285] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.285] (**) Power Button: always reports core events
[    17.285] (**) Power Button: Device: "/dev/input/event2"
[    17.285] (--) Power Button: Found keys
[    17.285] (II) Power Button: Configuring as keyboard
[    17.285] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[    17.285] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    17.285] (**) Option "xkb_rules" "evdev"
[    17.285] (**) Option "xkb_model" "pc105"
[    17.285] (**) Option "xkb_layout" "cz"
[    17.287] (II) XKB: reuse xkmfile /var/lib/xkb/server-583B992BBA3776030BA62AC94FC7F0AE9B04119F.xkm
[    17.314] (II) config/udev: Adding input device Video Bus (/dev/input/event9)
[    17.314] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    17.314] (II) Using input driver 'evdev' for 'Video Bus'
[    17.314] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.314] (**) Video Bus: always reports core events
[    17.314] (**) Video Bus: Device: "/dev/input/event9"
[    17.314] (--) Video Bus: Found keys
[    17.314] (II) Video Bus: Configuring as keyboard
[    17.314] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input9/event9"
[    17.314] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[    17.314] (**) Option "xkb_rules" "evdev"
[    17.314] (**) Option "xkb_model" "pc105"
[    17.314] (**) Option "xkb_layout" "cz"
[    17.315] (II) config/udev: Adding input device Video Bus (/dev/input/event10)
[    17.315] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    17.315] (II) Using input driver 'evdev' for 'Video Bus'
[    17.315] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.315] (**) Video Bus: always reports core events
[    17.315] (**) Video Bus: Device: "/dev/input/event10"
[    17.315] (--) Video Bus: Found keys
[    17.315] (II) Video Bus: Configuring as keyboard
[    17.315] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:09/LNXVIDEO:01/input/input10/event10"
[    17.315] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[    17.315] (**) Option "xkb_rules" "evdev"
[    17.315] (**) Option "xkb_model" "pc105"
[    17.315] (**) Option "xkb_layout" "cz"
[    17.334] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    17.334] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    17.334] (II) Using input driver 'evdev' for 'Power Button'
[    17.334] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.334] (**) Power Button: always reports core events
[    17.334] (**) Power Button: Device: "/dev/input/event1"
[    17.334] (--) Power Button: Found keys
[    17.334] (II) Power Button: Configuring as keyboard
[    17.334] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[    17.334] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[    17.334] (**) Option "xkb_rules" "evdev"
[    17.334] (**) Option "xkb_model" "pc105"
[    17.334] (**) Option "xkb_layout" "cz"
[    17.335] (II) config/udev: Adding input device Lid Switch (/dev/input/event0)
[    17.335] (II) No input driver/identifier specified (ignoring)
[    17.336] (II) config/udev: Adding input device HD-Audio Generic HDMI/DP,pcm=3 (/dev/input/event13)
[    17.336] (II) No input driver/identifier specified (ignoring)
[    17.337] (II) config/udev: Adding input device HP Webcam-101 (/dev/input/event4)
[    17.337] (**) HP Webcam-101: Applying InputClass "evdev keyboard catchall"
[    17.337] (II) Using input driver 'evdev' for 'HP Webcam-101'
[    17.337] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.337] (**) HP Webcam-101: always reports core events
[    17.337] (**) HP Webcam-101: Device: "/dev/input/event4"
[    17.337] (--) HP Webcam-101: Found keys
[    17.337] (II) HP Webcam-101: Configuring as keyboard
[    17.337] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input4/event4"
[    17.337] (II) XINPUT: Adding extended input device "HP Webcam-101" (type: KEYBOARD)
[    17.337] (**) Option "xkb_rules" "evdev"
[    17.337] (**) Option "xkb_model" "pc105"
[    17.337] (**) Option "xkb_layout" "cz"
[    17.338] (II) config/udev: Adding input device HDA Intel Mic (/dev/input/event11)
[    17.338] (II) No input driver/identifier specified (ignoring)
[    17.339] (II) config/udev: Adding input device HDA Intel Headphone (/dev/input/event12)
[    17.339] (II) No input driver/identifier specified (ignoring)
[    17.343] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event3)
[    17.343] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    17.343] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[    17.343] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.343] (**) AT Translated Set 2 keyboard: always reports core events
[    17.343] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event3"
[    17.343] (--) AT Translated Set 2 keyboard: Found keys
[    17.343] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[    17.343] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input3/event3"
[    17.343] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
[    17.343] (**) Option "xkb_rules" "evdev"
[    17.343] (**) Option "xkb_model" "pc105"
[    17.343] (**) Option "xkb_layout" "cz"
[    17.344] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event8)
[    17.344] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[    17.344] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[    17.344] (II) LoadModule: "synaptics"
[    17.345] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    17.352] (II) Module synaptics: vendor="X.Org Foundation"
[    17.352] compiled for 1.10.4, module version = 1.4.1
[    17.352] Module class: X.Org XInput Driver
[    17.352] ABI class: X.Org XInput driver, version 12.3
[    17.352] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[    17.352] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    17.352] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    17.352] (**) Option "Device" "/dev/input/event8"
[    17.416] (--) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5888
[    17.416] (--) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4844
[    17.416] (--) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[    17.416] (--) SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[    17.416] (--) SynPS/2 Synaptics TouchPad: buttons: left right double triple
[    17.452] (--) SynPS/2 Synaptics TouchPad: touchpad found
[    17.452] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    17.508] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input8/event8"
[    17.508] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
[    17.508] (**) SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[    17.508] (**) SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[    17.508] (**) SynPS/2 Synaptics TouchPad: AccelFactor is now 0.036
[    17.508] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[    17.508] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[    17.508] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[    17.508] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[    17.509] (--) SynPS/2 Synaptics TouchPad: touchpad found
[    17.509] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[    17.509] (II) No input driver/identifier specified (ignoring)
[    17.513] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event5)
[    17.513] (**) HP WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[    17.513] (II) Using input driver 'evdev' for 'HP WMI hotkeys'
[    17.513] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.513] (**) HP WMI hotkeys: always reports core events
[    17.513] (**) HP WMI hotkeys: Device: "/dev/input/event5"
[    17.513] (--) HP WMI hotkeys: Found keys
[    17.513] (II) HP WMI hotkeys: Configuring as keyboard
[    17.513] (**) Option "config_info" "udev:/sys/devices/virtual/input/input5/event5"
[    17.513] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD)
[    17.513] (**) Option "xkb_rules" "evdev"
[    17.513] (**) Option "xkb_model" "pc105"
[    17.513] (**) Option "xkb_layout" "cz"
[    17.840] (II) config/udev: Adding input device USB USB Keykoard (/dev/input/event14)
[    17.840] (**) USB USB Keykoard: Applying InputClass "evdev keyboard catchall"
[    17.840] (II) Using input driver 'evdev' for 'USB USB Keykoard'
[    17.840] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.840] (**) USB USB Keykoard: always reports core events
[    17.840] (**) USB USB Keykoard: Device: "/dev/input/event14"
[    17.840] (--) USB USB Keykoard: Found 1 mouse buttons
[    17.840] (--) USB USB Keykoard: Found scroll wheel(s)
[    17.840] (--) USB USB Keykoard: Found relative axes
[    17.840] (--) USB USB Keykoard: Found absolute axes
[    17.840] (II) evdev-grail: failed to open grail, no gesture support
[    17.840] (--) USB USB Keykoard: Found keys
[    17.840] (II) USB USB Keykoard: Configuring as mouse
[    17.840] (II) USB USB Keykoard: Configuring as keyboard
[    17.840] (II) USB USB Keykoard: Adding scrollwheel support
[    17.840] (**) USB USB Keykoard: YAxisMapping: buttons 4 and 5
[    17.840] (**) USB USB Keykoard: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    17.840] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3.4/2-1.3.4:1.1/input/input14/event14"
[    17.840] (II) XINPUT: Adding extended input device "USB USB Keykoard" (type: KEYBOARD)
[    17.840] (**) Option "xkb_rules" "evdev"
[    17.840] (**) Option "xkb_model" "pc105"
[    17.840] (**) Option "xkb_layout" "cz"
[    17.841] (EE) USB USB Keykoard: failed to initialize for relative axes.
[    17.841] (II) USB USB Keykoard: initialized for absolute axes.
[    17.841] (**) USB USB Keykoard: (accel) keeping acceleration scheme 1
[    17.841] (**) USB USB Keykoard: (accel) acceleration profile 0
[    17.841] (**) USB USB Keykoard: (accel) acceleration factor: 2.000
[    17.841] (**) USB USB Keykoard: (accel) acceleration threshold: 4
[    17.870] (II) config/udev: Adding input device  USB OPTICAL MOUSE (/dev/input/event6)
[    17.870] (**)  USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[    17.870] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[    17.870] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.870] (**)  USB OPTICAL MOUSE: always reports core events
[    17.870] (**)  USB OPTICAL MOUSE: Device: "/dev/input/event6"
[    17.870] (--)  USB OPTICAL MOUSE: Found 3 mouse buttons
[    17.870] (--)  USB OPTICAL MOUSE: Found scroll wheel(s)
[    17.870] (--)  USB OPTICAL MOUSE: Found relative axes
[    17.870] (--)  USB OPTICAL MOUSE: Found x and y relative axes
[    17.870] (II)  USB OPTICAL MOUSE: Configuring as mouse
[    17.870] (II)  USB OPTICAL MOUSE: Adding scrollwheel support
[    17.870] (**)  USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[    17.870] (**)  USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    17.870] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3.3/2-1.3.3:1.0/input/input6/event6"
[    17.870] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE)
[    17.870] (II)  USB OPTICAL MOUSE: initialized for relative axes.
[    17.870] (**)  USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[    17.870] (**)  USB OPTICAL MOUSE: (accel) acceleration profile 0
[    17.870] (**)  USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[    17.870] (**)  USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[    17.871] (II) config/udev: Adding input device  USB OPTICAL MOUSE (/dev/input/mouse0)
[    17.871] (II) No input driver/identifier specified (ignoring)
[    17.876] (II) config/udev: Adding input device USB USB Keykoard (/dev/input/event7)
[    17.876] (**) USB USB Keykoard: Applying InputClass "evdev keyboard catchall"
[    17.876] (II) Using input driver 'evdev' for 'USB USB Keykoard'
[    17.876] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    17.876] (**) USB USB Keykoard: always reports core events
[    17.876] (**) USB USB Keykoard: Device: "/dev/input/event7"
[    17.876] (--) USB USB Keykoard: Found keys
[    17.876] (II) USB USB Keykoard: Configuring as keyboard
[    17.876] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3.4/2-1.3.4:1.0/input/input7/event7"
[    17.876] (II) XINPUT: Adding extended input device "USB USB Keykoard" (type: KEYBOARD)
[    17.876] (**) Option "xkb_rules" "evdev"
[    17.876] (**) Option "xkb_model" "pc105"
[    17.876] (**) Option "xkb_layout" "cz"
[    26.628] (II) intel(0): EDID vendor "CMO", prod id 5522
[    26.629] (II) intel(0): Printing DDC gathered Modelines:
[    26.629] (II) intel(0): Modeline "1366x768"x0.0   69.30  1366 1382 1416 1466  768 770 776 788 -hsync -vsync (47.3 kHz)
[    29.211] (II) intel(0): EDID vendor "CMO", prod id 5522
[    29.211] (II) intel(0): Printing DDC gathered Modelines:
[    29.211] (II) intel(0): Modeline "1366x768"x0.0   69.30  1366 1382 1416 1466  768 770 776 788 -hsync -vsync (47.3 kHz)
[    31.043] (II) XKB: reuse xkmfile /var/lib/xkb/server-3C2EA826D38C0E9DCCF897457B6117E0ACB24BCB.xkm
[    35.769] (II) intel(0): EDID vendor "CMO", prod id 5522
[    35.769] (II) intel(0): Printing DDC gathered Modelines:
[    35.769] (II) intel(0): Modeline "1366x768"x0.0   69.30  1366 1382 1416 1466  768 770 776 788 -hsync -vsync (47.3 kHz)
[    49.659] (II) XKB: reuse xkmfile /var/lib/xkb/server-3C2EA826D38C0E9DCCF897457B6117E0ACB24BCB.xkm
[  3086.393] (II) intel(0): EDID vendor "CMO", prod id 5522
[  3086.393] (II) intel(0): Printing DDC gathered Modelines:
[  3086.393] (II) intel(0): Modeline "1366x768"x0.0   69.30  1366 1382 1416 1466  768 770 776 788 -hsync -vsync (47.3 kHz)
************************************

Eran

  • Návštěvník
  • *
  • Příspěvků: 8
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #8 kdy: 04 Listopadu 2011, 20:42:34 »
Tak baterka mi nevadi... mam to stale na elektrice...... v biosu jsem se dival a nejde vzpnout vubec tam nemam zminku o grafice

sabraq

  • Závislák
  • ****
  • Příspěvků: 3395
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #9 kdy: 04 Listopadu 2011, 20:55:13 »
No jo, takže buď - vypnout sofwarově ten intel a používat ati (takhle se to původně řešilo), nebo zkusit rozběhnout switcheroo na přepínání grafik s restartem xserveru (asi nexxistuje zatím nikdo, komu by to použitelně fungovalo).

Nějaké odkazy

http://forums.gentoo.org/viewtopic-t-871379-highlight-intel.html
http://linux-hybrid-graphics.blogspot.com/
https://bugs.launchpad.net/lpbugreporter/+bug/752542
http://www.phoronix.com/scan.php?page=article&item=intel_snb_natty&num=1

P.s. Sandy bridge není jaksi linux friendly:/
************************************

Eran

  • Návštěvník
  • *
  • Příspěvků: 8
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #10 kdy: 04 Listopadu 2011, 21:01:21 »
Asi vam budu k smichu  ale jak se to vypne soft?   stema strankama moc nepochodim ac nerad musim rict ye anlictina neni moje silne slovo...
Asi si rikate co za vola se pustilo do  linuxu 8)
TEd nav9c p5 irestartov8n9 kdz6 sem zkousel  instalovat ovladace mi  linuxx haye pri nacitani failed u nejakeho USB tak sem zatim na live CD mackal jsem Del pri  restartovani ....

sabraq

  • Závislák
  • ****
  • Příspěvků: 3395
    • Zobrazit profil
Re:Pomoc zapnutí 3d akcelerace nováčkovy co prakticky začína s linuxem...
« Odpověď #11 kdy: 04 Listopadu 2011, 21:30:10 »
Ale vůbec ne... ten postup je popsaný buď na tom blogu, nebo jsem ho našel u nějakého bugu...

Citace
ATI hybrid:
The PowerXpress pre-4.0 models have a mux solution to switch between
discrete and integrated card.
For most ATI/Intel hybrid configurations:

a) try the latest closed-source Catalyst Driver for login/logout card switching,
 or
b) try vga_switcheroo and open-source graphics drivers (kernel 2.6.35 or newer).

Tak já nevím, podle bodu a) by to měli umět i ovladače od ATI... a to switcheroo jenom s otevřeným ovladačem, to jsem si myslel.

Zkus nainstalovat poslední verzi ovladačů http://support.amd.com/us/gpudownload/linux/Pages/radeon_linux.aspx

Jakmile stáhneš ten soubor, otevři terminál a vytvoř si .deb balíčky, až teprve ty instaluj:

Kód: [Vybrat]
sudo apt-get install build-essential cdbs fakeroot dh-make debhelper debconf libstdc++6 dkms libqtgui4 wget execstack libelfg0 dh-modaliases

sudo apt-get install ia32-libs

cd /Stažené

sudo sh ./ati-driver-installer-11-9-x86.x86_64.run --buildpkg Ubuntu/oneiric

Měli by vzniknout 4 balíčky (driver, kernel,amdccc,modaliases) .deb, všechny je pak klasickým způsobem nainstaluj (hlavně driver a kernel). Pokud máš starší verzi Ubuntu, napiš správný název na konec řádku za parametr --buildpkg Ubuntu/natty (lucid, atd.). Pokud nemáš 64bitový systém, nemusíš instalovat ia32libs...

Mrkni i sem http://wiki.cchtml.com/index.php/Ubuntu_Oneiric_Installation_Guide.

Když budeš mít problém, zkopíruj výstup z terminálu sem do code...
************************************

 


Provoz zaštiťuje spolek OpenAlt.