Pro zprovoznění tuneru DVBT USB v Ubuntu 16.04 bych potřeboval stáhnout a nainstalovat firmware xc3028-v27.fw. Prosím o pomoc, sám jsem pouze uživatelem linuxu, s terminálem se moc nekamarádím a tak v tom lítám. Připojuji část výpisu z terminálu. Děkuji.
7.300522] em2882/3 #0: Board detected as Pinnacle Hybrid Pro
[ 7.440105] em2882/3 #0: Identified as Pinnacle Hybrid Pro (card=53)
[ 7.440110] em2882/3 #0: analog set to isoc mode.
[ 7.440111] em2882/3 #0: dvb set to isoc mode.
[ 7.440168] em28xx audio device (eb1a:2881): interface 1, class 1
[ 7.440178] em28xx audio device (eb1a:2881): interface 2, class 1
[ 7.440209] usbcore: registered new interface driver em28xx
[ 7.447944] em2882/3 #0: Registering V4L2 extension
[ 7.456091] usbcore: registered new interface driver snd-usb-audio
[ 7.460511] tvp5150 6-005c: chip found @ 0xb8 (em2882/3 #0)
[ 7.460515] tvp5150 6-005c: tvp5150am1 detected.
[ 7.478705] tuner 6-0061: Tuner -1 found with type(s) Radio TV.
[ 7.488663] xc2028 6-0061: creating new instance
[ 7.488666] xc2028 6-0061: type set to XCeive xc2028/xc3028 tuner
[ 7.488759] em2882/3 #0: Config register raw data: 0x58
[ 7.489511] em2882/3 #0: AC97 vendor ID = 0xffffffff
[ 7.489885] em2882/3 #0: AC97 features = 0x6a90
[ 7.489887] em2882/3 #0: Empia 202 AC97 audio processor detected
[ 7.533015] cgroup: new mount options do not match the existing superblock, will be ignored
[ 7.564359] gpio_ich: GPIO from 462 to 511 on gpio_ich
[ 7.660416] usb 1-3: Direct firmware load for xc3028-v27.fw failed with error -2
[ 7.660425] xc2028 6-0061: Could not load firmware xc3028-v27.fw.
[ 7.788661] em2882/3 #0: V4L2 video device registered as video1
[ 7.788664] em2882/3 #0: V4L2 VBI device registered as vbi0
[ 7.788669] em2882/3 #0: V4L2 extension successfully initialized
[ 7.788671] em28xx: Registered (Em28xx v4l2 Extension) extension
[ 7.820609] em2882/3 #0: Binding DVB extension
[ 8.211794] xc2028 6-0061: attaching existing instance
[ 8.211800] xc2028 6-0061: type set to XCeive xc2028/xc3028 tuner
[ 8.211804] em2882/3 #0: em2882/3 #0/2: xc3028 attached
[ 8.211807] DVB: registering new adapter (em2882/3 #0)
[ 8.211814] usb 1-3: DVB: registering adapter 0 frontend 0 (Zarlink ZL10353 DVB-T)...
[ 8.214277] em2882/3 #0: DVB extension successfully initialized
[ 8.214284] em28xx: Registered (Em28xx dvb Extension) extension
[ 9.566026] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.566370] atl1 0000:01:00.0: eth0 link is up 100 Mbps full duplex
[ 9.640041] floppy0: no floppy controllers found
[ 12.880441] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 12.903567] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 12.942695] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 12.965697] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 28.481063] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 28.504051] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 28.544158] usb 1-1: 3:1: cannot get freq at ep 0x84
[ 28.567273] usb 1-1: 3:1: cannot get freq at ep 0x84