Ahoj, mám lenovo x230 a když zadockuju, je vše ok, jedu po kabelu. Když vytrhnu NB z docku, už mi nenajede wifi, musím restartovat. Mám UBUNTU 16.04
Přikládám výpis z dmesg po undocku :
[87339.729354] wlp3s0: deauthenticating from d4:xx:xx:xx:xx:xx by local choice (Reason: 3=DEAUTH_LEAVING)
[87339.744186] cfg80211: World regulatory domain updated:
[87339.744192] cfg80211: DFS Master region: unset
[87339.744194] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[87339.744199] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[87339.744202] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[87339.744206] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[87339.744210] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[87339.744214] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[87339.744218] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[87339.744221] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[87339.744225] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[87340.367640] PM: Syncing filesystems ... done.
[87340.389861] PM: Preparing system for sleep (mem)
[87340.390089] Freezing user space processes ... (elapsed 0.001 seconds) done.
[87340.391665] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[87340.392877] PM: Suspending system (mem)
[87340.392889] Suspending console(s) (use no_console_suspend to debug)
[87340.516935] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[87340.517041] sd 0:0:0:0: [sda] Stopping disk
[87340.739936] e1000e: EEE TX LPI TIMER: 00000011
[87340.815806] PM: suspend of devices complete after 422.779 msecs
[87340.831741] PM: late suspend of devices complete after 15.909 msecs
[87340.835264] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[87340.835384] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[87340.835444] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[87340.835641] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[87340.851601] PM: noirq suspend of devices complete after 19.856 msecs
[87340.851890] ACPI: Preparing to enter system sleep state S3
[87341.023626] ACPI : EC: EC stopped
[87341.023627] PM: Saving platform NVS memory
[87341.023633] Disabling non-boot CPUs ...
[87341.024035] Broke affinity for irq 29
[87341.025070] smpboot: CPU 1 is now offline
[87341.036597] Broke affinity for irq 25
[87341.036599] Broke affinity for irq 27
[87341.036601] Broke affinity for irq 29
[87341.037632] smpboot: CPU 2 is now offline
[87341.052342] Broke affinity for irq 1
[87341.052351] Broke affinity for irq 9
[87341.052355] Broke affinity for irq 12
[87341.052359] Broke affinity for irq 16
[87341.052364] Broke affinity for irq 23
[87341.052367] Broke affinity for irq 24
[87341.052368] Broke affinity for irq 25
[87341.052370] Broke affinity for irq 27
[87341.052372] Broke affinity for irq 29
[87341.053397] smpboot: CPU 3 is now offline
[87341.065816] ACPI: Low-level resume complete
[87341.065880] ACPI : EC: EC started
[87341.065881] PM: Restoring platform NVS memory
[87341.067432] microcode: CPU0 microcode updated early to revision 0x1c, date = 2015-02-26
[87341.067477] Enabling non-boot CPUs ...
[87341.085973] x86: Booting SMP configuration:
[87341.085975] smpboot: Booting Node 0 Processor 1 APIC 0x1
[87341.121882] cache: parent cpu1 should not be sleeping
[87341.122077] CPU1 is up
[87341.142018] smpboot: Booting Node 0 Processor 2 APIC 0x2
[87341.143117] microcode: CPU2 microcode updated early to revision 0x1c, date = 2015-02-26
[87341.177882] cache: parent cpu2 should not be sleeping
[87341.178080] CPU2 is up
[87341.198077] smpboot: Booting Node 0 Processor 3 APIC 0x3
[87341.229866] cache: parent cpu3 should not be sleeping
[87341.230054] CPU3 is up
[87341.235183] ACPI: Waking up from system sleep state S3
[87341.429940] thinkpad_acpi: EC reports that Thermal Table has changed
[87341.614857] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[87341.615783] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[87341.615901] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[87341.615939] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[87341.616094] PM: noirq resume of devices complete after 18.349 msecs
[87341.616533] PM: early resume of devices complete after 0.405 msecs
[87341.620005] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[87341.626503] rtc_cmos 00:02: System wakeup disabled by ACPI
[87341.627021] sd 0:0:0:0: [sda] Starting disk
[87341.861786] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[87341.961755] ata5: SATA link down (SStatus 0 SControl 300)
[87341.961780] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[87341.961801] ata2: SATA link down (SStatus 0 SControl 300)
[87341.962611] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87341.962614] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87341.962617] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87341.964777] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87341.964781] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87341.964783] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87341.966071] ata1.00: configured for UDMA/133
[87342.025744] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[87342.193765] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[87342.334208] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[87342.364522] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[87342.473930] PM: resume of devices complete after 857.388 msecs
[87342.475016] PM: Finishing wakeup.
[87342.475019] Restarting tasks ...
[87342.475325] usb 2-1.8: USB disconnect, device number 3
[87342.475334] usb 2-1.8.6: USB disconnect, device number 4
[87342.480118] Bluetooth: hci0: BCM: chip id 63
[87342.489744] done.
[87342.496012] Bluetooth: hci0: BCM20702A
[87342.497078] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[87342.497116] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[87342.497124] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[87342.507240] video LNXVIDEO:00: Restoring backlight state
[87342.678299] e1000e: enp0s25 NIC Link is Down
[87342.679381] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87342.679593] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87342.686155] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87342.686256] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87342.956634] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87342.963190] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87342.963292] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87343.044594] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87343.046348] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87343.278117] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87343.325293] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87353.934254] PM: Syncing filesystems ... done.
[87353.949576] PM: Preparing system for sleep (mem)
[87353.949925] Freezing user space processes ... (elapsed 0.001 seconds) done.
[87353.951906] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[87353.953193] PM: Suspending system (mem)
[87353.953207] Suspending console(s) (use no_console_suspend to debug)
[87354.107431] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[87354.107496] sd 0:0:0:0: [sda] Stopping disk
[87354.318116] e1000e: EEE TX LPI TIMER: 00000011
[87354.569949] PM: suspend of devices complete after 616.578 msecs
[87354.585964] PM: late suspend of devices complete after 16.008 msecs
[87354.588720] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[87354.588822] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[87354.588966] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[87354.589029] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[87354.602189] PM: noirq suspend of devices complete after 16.222 msecs
[87354.602469] ACPI: Preparing to enter system sleep state S3
[87354.773839] ACPI : EC: EC stopped
[87354.773840] PM: Saving platform NVS memory
[87354.773846] Disabling non-boot CPUs ...
[87354.774256] Broke affinity for irq 29
[87354.775291] smpboot: CPU 1 is now offline
[87354.786677] Broke affinity for irq 25
[87354.786680] Broke affinity for irq 27
[87354.786683] Broke affinity for irq 29
[87354.787723] smpboot: CPU 2 is now offline
[87354.798614] Broke affinity for irq 1
[87354.798623] Broke affinity for irq 9
[87354.798628] Broke affinity for irq 12
[87354.798632] Broke affinity for irq 16
[87354.798637] Broke affinity for irq 23
[87354.798639] Broke affinity for irq 24
[87354.798641] Broke affinity for irq 25
[87354.798642] Broke affinity for irq 27
[87354.798644] Broke affinity for irq 29
[87354.799678] smpboot: CPU 3 is now offline
[87354.816057] ACPI: Low-level resume complete
[87354.816123] ACPI : EC: EC started
[87354.816124] PM: Restoring platform NVS memory
[87354.817682] microcode: CPU0 microcode updated early to revision 0x1c, date = 2015-02-26
[87354.817728] Enabling non-boot CPUs ...
[87354.836179] x86: Booting SMP configuration:
[87354.836180] smpboot: Booting Node 0 Processor 1 APIC 0x1
[87354.868094] cache: parent cpu1 should not be sleeping
[87354.868288] CPU1 is up
[87354.888210] smpboot: Booting Node 0 Processor 2 APIC 0x2
[87354.889238] microcode: CPU2 microcode updated early to revision 0x1c, date = 2015-02-26
[87354.924092] cache: parent cpu2 should not be sleeping
[87354.924286] CPU2 is up
[87354.944286] smpboot: Booting Node 0 Processor 3 APIC 0x3
[87354.976078] cache: parent cpu3 should not be sleeping
[87354.976265] CPU3 is up
[87354.981374] ACPI: Waking up from system sleep state S3
[87355.332143] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[87355.332172] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[87355.334864] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[87355.334921] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[87355.335096] PM: noirq resume of devices complete after 19.116 msecs
[87355.335504] PM: early resume of devices complete after 0.384 msecs
[87355.336220] rtc_cmos 00:02: System wakeup disabled by ACPI
[87355.336359] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[87355.340131] sd 0:0:0:0: [sda] Starting disk
[87355.567968] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[87355.664003] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[87355.664054] ata5: SATA link down (SStatus 0 SControl 300)
[87355.664700] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87355.664704] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87355.664707] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87355.668529] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87355.668532] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87355.668535] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87355.670716] ata1.00: configured for UDMA/133
[87355.679990] ata2: SATA link down (SStatus 0 SControl 300)
[87355.735980] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[87355.899980] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[87356.072745] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[87356.102563] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[87356.196222] PM: resume of devices complete after 860.707 msecs
[87356.197490] PM: Finishing wakeup.
[87356.197492] Restarting tasks ...
[87356.201874] Bluetooth: hci0: BCM: chip id 63
[87356.210091] done.
[87356.217872] Bluetooth: hci0: BCM20702A
[87356.218795] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[87356.218823] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[87356.218828] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[87356.240653] video LNXVIDEO:00: Restoring backlight state
[87356.390786] e1000e: enp0s25 NIC Link is Down
[87356.391414] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87356.391625] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87356.398179] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87356.398291] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87356.670706] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87356.677288] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87356.677392] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87356.760375] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87356.762048] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87356.996343] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87357.051838] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87402.891672] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio.
[87402.894987] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[87402.895028] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[87402.955769] usb 1-1.4: USB disconnect, device number 4
[87405.089551] iwlwifi 0000:03:00.0: RF_KILL bit toggled to enable radio.
[87405.093328] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87405.095987] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87405.096093] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87405.367112] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87405.373685] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87405.373786] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87405.455282] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87405.456336] usb 1-1.4: new full-speed USB device number 7 using ehci-pci
[87405.504764] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87405.553907] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=21e6
[87405.553914] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[87405.553917] usb 1-1.4: Product: BCM20702A0
[87405.553919] usb 1-1.4: Manufacturer: Broadcom Corp
[87405.553921] usb 1-1.4: SerialNumber: 2016XXXXXX2B
[87405.561378] Bluetooth: hci0: BCM: chip id 63
[87405.577389] Bluetooth: hci0: BCM20702A
[87405.578456] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[87405.578482] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[87405.578487] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[87420.757941] PM: Syncing filesystems ... done.
[87420.784504] PM: Preparing system for sleep (mem)
[87420.784893] Freezing user space processes ... (elapsed 0.002 seconds) done.
[87420.787074] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[87420.788471] PM: Suspending system (mem)
[87420.788488] Suspending console(s) (use no_console_suspend to debug)
[87420.932537] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[87420.932671] sd 0:0:0:0: [sda] Stopping disk
[87421.144778] e1000e: EEE TX LPI TIMER: 00000011
[87421.387071] PM: suspend of devices complete after 598.405 msecs
[87421.400600] PM: late suspend of devices complete after 13.521 msecs
[87421.403587] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[87421.403828] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[87421.403835] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[87421.404015] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[87421.416759] PM: noirq suspend of devices complete after 16.154 msecs
[87421.417200] ACPI: Preparing to enter system sleep state S3
[87421.588509] ACPI : EC: EC stopped
[87421.588510] PM: Saving platform NVS memory
[87421.588516] Disabling non-boot CPUs ...
[87421.588921] Broke affinity for irq 23
[87421.588925] Broke affinity for irq 24
[87421.588929] Broke affinity for irq 29
[87421.589959] smpboot: CPU 1 is now offline
[87421.601522] Broke affinity for irq 23
[87421.601525] Broke affinity for irq 24
[87421.601527] Broke affinity for irq 25
[87421.601529] Broke affinity for irq 27
[87421.601531] Broke affinity for irq 29
[87421.602559] smpboot: CPU 2 is now offline
[87421.613184] Broke affinity for irq 1
[87421.613192] Broke affinity for irq 9
[87421.613197] Broke affinity for irq 12
[87421.613202] Broke affinity for irq 16
[87421.613206] Broke affinity for irq 23
[87421.613209] Broke affinity for irq 24
[87421.613210] Broke affinity for irq 25
[87421.613212] Broke affinity for irq 27
[87421.613214] Broke affinity for irq 29
[87421.614251] smpboot: CPU 3 is now offline
[87421.630822] ACPI: Low-level resume complete
[87421.630885] ACPI : EC: EC started
[87421.630885] PM: Restoring platform NVS memory
[87421.632459] microcode: CPU0 microcode updated early to revision 0x1c, date = 2015-02-26
[87421.632493] Enabling non-boot CPUs ...
[87421.650906] x86: Booting SMP configuration:
[87421.650908] smpboot: Booting Node 0 Processor 1 APIC 0x1
[87421.686776] cache: parent cpu1 should not be sleeping
[87421.686968] CPU1 is up
[87421.706950] smpboot: Booting Node 0 Processor 2 APIC 0x2
[87421.708045] microcode: CPU2 microcode updated early to revision 0x1c, date = 2015-02-26
[87421.742808] cache: parent cpu2 should not be sleeping
[87421.743002] CPU2 is up
[87421.763007] smpboot: Booting Node 0 Processor 3 APIC 0x3
[87421.794797] cache: parent cpu3 should not be sleeping
[87421.794990] CPU3 is up
[87421.800110] ACPI: Waking up from system sleep state S3
[87422.150897] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[87422.150900] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[87422.153867] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[87422.154111] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[87422.154233] PM: noirq resume of devices complete after 19.532 msecs
[87422.154655] PM: early resume of devices complete after 0.398 msecs
[87422.154839] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[87422.155335] rtc_cmos 00:02: System wakeup disabled by ACPI
[87422.170798] sd 0:0:0:0: [sda] Starting disk
[87422.390728] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[87422.498698] ata2: SATA link down (SStatus 0 SControl 300)
[87422.498721] ata5: SATA link down (SStatus 0 SControl 300)
[87422.506692] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[87422.507729] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87422.507732] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87422.507735] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87422.508479] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87422.508482] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87422.508484] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87422.508809] ata1.00: configured for UDMA/133
[87422.554710] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[87422.722709] usb 1-1.4: reset full-speed USB device number 7 using ehci-pci
[87422.874708] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[87422.905368] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[87423.018782] PM: resume of devices complete after 864.113 msecs
[87423.019970] PM: Finishing wakeup.
[87423.019972] Restarting tasks ...
[87423.025779] Bluetooth: hci0: BCM: chip id 63
[87423.035534] done.
[87423.041738] Bluetooth: hci0: BCM20702A
[87423.042964] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[87423.042992] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[87423.042997] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[87423.057924] video LNXVIDEO:00: Restoring backlight state
[87423.233365] e1000e: enp0s25 NIC Link is Down
[87423.234048] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87423.234294] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87423.240880] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87423.240981] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87423.512663] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87423.519227] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87423.519329] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87423.606264] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87423.607046] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87423.843051] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87423.887022] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87431.411457] PM: Syncing filesystems ... done.
[87431.422481] PM: Preparing system for sleep (mem)
[87431.422643] Freezing user space processes ... (elapsed 0.002 seconds) done.
[87431.424924] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[87431.426298] PM: Suspending system (mem)
[87431.426316] Suspending console(s) (use no_console_suspend to debug)
[87431.550386] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[87431.550534] sd 0:0:0:0: [sda] Stopping disk
[87431.767152] e1000e: EEE TX LPI TIMER: 00000011
[87432.011041] PM: suspend of devices complete after 584.540 msecs
[87432.026858] PM: late suspend of devices complete after 15.807 msecs
[87432.029683] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[87432.029864] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[87432.029878] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[87432.030099] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[87432.043078] PM: noirq suspend of devices complete after 16.215 msecs
[87432.043539] ACPI: Preparing to enter system sleep state S3
[87432.214805] ACPI : EC: EC stopped
[87432.214806] PM: Saving platform NVS memory
[87432.214812] Disabling non-boot CPUs ...
[87432.215219] Broke affinity for irq 23
[87432.215222] Broke affinity for irq 24
[87432.215227] Broke affinity for irq 29
[87432.216255] smpboot: CPU 1 is now offline
[87432.227667] Broke affinity for irq 23
[87432.227671] Broke affinity for irq 24
[87432.227673] Broke affinity for irq 25
[87432.227675] Broke affinity for irq 27
[87432.227677] Broke affinity for irq 29
[87432.228716] smpboot: CPU 2 is now offline
[87432.243573] Broke affinity for irq 1
[87432.243581] Broke affinity for irq 9
[87432.243586] Broke affinity for irq 12
[87432.243590] Broke affinity for irq 16
[87432.243595] Broke affinity for irq 23
[87432.243597] Broke affinity for irq 24
[87432.243599] Broke affinity for irq 25
[87432.243600] Broke affinity for irq 27
[87432.243602] Broke affinity for irq 29
[87432.244632] smpboot: CPU 3 is now offline
[87432.261083] ACPI: Low-level resume complete
[87432.261150] ACPI : EC: EC started
[87432.261150] PM: Restoring platform NVS memory
[87432.262696] microcode: CPU0 microcode updated early to revision 0x1c, date = 2015-02-26
[87432.262722] Enabling non-boot CPUs ...
[87432.281177] x86: Booting SMP configuration:
[87432.281179] smpboot: Booting Node 0 Processor 1 APIC 0x1
[87432.317092] cache: parent cpu1 should not be sleeping
[87432.317292] CPU1 is up
[87432.337221] smpboot: Booting Node 0 Processor 2 APIC 0x2
[87432.338322] microcode: CPU2 microcode updated early to revision 0x1c, date = 2015-02-26
[87432.373092] cache: parent cpu2 should not be sleeping
[87432.373288] CPU2 is up
[87432.393279] smpboot: Booting Node 0 Processor 3 APIC 0x3
[87432.425067] cache: parent cpu3 should not be sleeping
[87432.425251] CPU3 is up
[87432.430361] ACPI: Waking up from system sleep state S3
[87432.784638] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[87432.787584] sdhci-pci 0000:02:00.0: MMC controller base frequency changed to 50Mhz.
[87432.787646] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[87432.787826] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[87432.788014] PM: noirq resume of devices complete after 23.042 msecs
[87432.788426] PM: early resume of devices complete after 0.387 msecs
[87432.788999] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[87432.789685] rtc_cmos 00:02: System wakeup disabled by ACPI
[87432.797000] sd 0:0:0:0: [sda] Starting disk
[87433.020987] usb 1-1.4: reset full-speed USB device number 7 using ehci-pci
[87433.116968] ata2: SATA link down (SStatus 0 SControl 300)
[87433.125005] ata5: SATA link down (SStatus 0 SControl 300)
[87433.125029] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[87433.125917] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87433.125921] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87433.125923] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87433.129712] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[87433.129715] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[87433.129718] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[87433.131889] ata1.00: configured for UDMA/133
[87433.184997] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[87433.348955] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[87433.504399] psmouse serio1: synaptics: queried max coordinates: x [..5768], y [..5062]
[87433.534716] psmouse serio1: synaptics: queried min coordinates: x [1174..], y [790..]
[87433.644233] PM: resume of devices complete after 855.792 msecs
[87433.645755] PM: Finishing wakeup.
[87433.645757] Restarting tasks ...
[87433.649682] Bluetooth: hci0: BCM: chip id 63
[87433.669043] Bluetooth: hci0: BCM20702A
[87433.670581] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
[87433.675109] done.
[87433.675134] bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2
[87433.675141] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found
[87433.696260] video LNXVIDEO:00: Restoring backlight state
[87433.838031] e1000e: enp0s25 NIC Link is Down
[87433.838590] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87433.838785] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87433.845337] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87433.845437] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87434.128461] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87434.135119] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87434.135222] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87434.215884] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87434.217367] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87434.453502] IPv6: ADDRCONF(NETDEV_UP): enp0s25: link is not ready
[87434.503235] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87470.269901] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87470.276476] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87470.276577] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87470.547652] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87470.554216] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[87470.554318] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[87470.635934] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[87470.671726] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
Ted si nevzpomenu, jesli mi pri tom vyndavani i usnul, mozna jo - ten vypis je uz tyden stary. Ale opakuje se to porad. Vyndam z docku a uz se wifi nechyti. Vidite tam nejaky problem? Pripadne prosim o info, jaky vypis jeste dodat a co zkusit, kdyz prestane jit wifi, abych zjistil, kde je problem.
Téma: X230 - po undock už nenajede wifi (Přečteno 1637 krát)
