Nainstaloval jsem Xubuntu 7.04 na (hodně) starý notebook a mám problémy se zařízeními... např. CD-ROM.
CD-ROM je externí, připojená přes PCMCIA (karta je tuším od CNF), v DOSu a Win 98 funguje s vlastním driverem, pro Linux samozřejmě žádný nemám. Všechen ten HW je spíš vykopávka.
Xubuntu 6.10 tu kartu kupodivu najde (a funguje), v 7.04 se prostě nenajde. Zkoušel jsem natáhnout všechny možné moduly, ale bezvýsledně (možná to dělám špatně). Přikládám syslog a lspci atd, ale myslím, že kritická je následující část dmesg, napřed ta funkční z 6.10:
...
[ 6297.268889] PCI: Found IRQ 12 for device 0000:00:0a.0
[ 6297.269027] Yenta: CardBus bridge found at 0000:00:0a.0 [7878:7788]
[ 6297.269128] Yenta: Enabling burst memory read transactions
[ 6297.269209] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 6297.269287] Yenta: Routing CardBus interrupts to PCI
[ 6297.269368] Yenta TI: socket 0000:00:0a.0, mfunc 0x010c1000, devctl 0x66
[ 6297.500554] Yenta: ISA IRQ mask 0x0c18, PCI irq 12
[ 6297.500648] Socket status: 30000059
[ 6297.501812] PCI: Found IRQ 12 for device 0000:00:0a.1
[ 6297.501947] Yenta: CardBus bridge found at 0000:00:0a.1 [7878:7788]
[ 6297.502050] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 6297.502129] Yenta: Routing CardBus interrupts to PCI
[ 6297.502211] Yenta TI: socket 0000:00:0a.1, mfunc 0x010c1000, devctl 0x66
[ 6297.732558] Yenta: ISA IRQ mask 0x0c18, PCI irq 12
[ 6297.732641] Socket status: 30000068
[ 6298.135703] pccard: PCMCIA card inserted into slot 0
[ 6298.391604] pccard: CardBus card inserted into slot 1
[ 6298.396961] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 6298.399684] cs: IO port probe 0x3e0-0x4ff: clean.
[ 6298.400882] cs: IO port probe 0x820-0x8ff: clean.
[ 6298.401937] cs: IO port probe 0xc00-0xcf7: clean.
[ 6298.403474] cs: IO port probe 0xa00-0xaff: excluding 0xa50-0xa57 0xaf8-0xaff
[ 6298.404966] cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 6298.412284] pcmcia: registering new device pcmcia0.0
[ 6298.417056] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 6298.419800] cs: IO port probe 0x3e0-0x4ff: clean.
[ 6298.421002] cs: IO port probe 0x820-0x8ff: clean.
[ 6298.422055] cs: IO port probe 0xc00-0xcf7: clean.
[ 6298.423631] cs: IO port probe 0xa00-0xaff: excluding 0xa50-0xa57 0xaf8-0xaff
[ 6298.560100] SCSI subsystem initialized
[ 6298.597520] libata version 1.20 loaded.
[ 6298.654146] ata1: PATA max PIO0 cmd 0x320 ctl 0x32E bmdma 0x0 irq 3
[ 6298.979427] ata1: dev 0 cfg 49:2020 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0000
[ 6298.979450] ata1: dev 0 ATAPI, max PIO0
[ 6298.979527] scsi0 : pata_pcmcia
[ 6298.987614] Vendor: PCMCIA Model: OTI-910/CDT-666 Rev: 9.19
[ 6298.988921] Type: CD-ROM ANSI SCSI revision: 05
[ 6299.079448] sr0: scsi3-mmc drive: 8x/8x xa/form2 cdda pop-up
[ 6299.079549] Uniform CD-ROM driver Revision: 3.20
[ 6299.090721] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 6299.117635] sr 0:0:0:0: Attached scsi generic sg0 type 5
....
V 7.04 ta fáze probíhá následovně:
...
[ 6947.412139] PCI: Bus 1, cardbus bridge: 0000:00:0a.0
[ 6947.412162] IO window: 00001000-000010ff
[ 6947.412180] IO window: 00001400-000014ff
[ 6947.412198] PREFETCH window: 10000000-13ffffff
[ 6947.412216] MEM window: 14000000-17ffffff
[ 6947.412232] PCI: Bus 5, cardbus bridge: 0000:00:0a.1
[ 6947.412246] IO window: 00001800-000018ff
[ 6947.412261] IO window: 00001c00-00001cff
[ 6947.412278] PREFETCH window: 18000000-1bffffff
[ 6947.412296] MEM window: 1c000000-1fffffff
[ 6947.412349] PCI: setting IRQ 12 as level-triggered
[ 6947.412366] PCI: Assigned IRQ 12 for device 0000:00:0a.0
[ 6947.412431] PCI: Assigned IRQ 12 for device 0000:00:0a.1
[ 6958.476278] SCSI subsystem initialized
[ 6958.540156] libata version 2.20 loaded.
[ 6994.316967] Yenta: CardBus bridge found at 0000:00:0a.0 [7878:7788]
[ 6994.317012] Yenta: Enabling burst memory read transactions
[ 6994.317030] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 6994.317043] Yenta: Routing CardBus interrupts to PCI
[ 6994.317062] Yenta TI: socket 0000:00:0a.0, mfunc 0x010c1000, devctl 0x66
[ 6994.547380] Yenta: ISA IRQ mask 0x0c98, PCI irq 12
[ 6994.547400] Socket status: 30000059
[ 6994.548061] Yenta: CardBus bridge found at 0000:00:0a.1 [7878:7788]
[ 6994.548104] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 6994.548117] Yenta: Routing CardBus interrupts to PCI
[ 6994.548137] Yenta TI: socket 0000:00:0a.1, mfunc 0x010c1000, devctl 0x66
[ 6994.779285] Yenta: ISA IRQ mask 0x0c98, PCI irq 12
[ 6994.779305] Socket status: 30000068
[ 6995.182397] pccard: PCMCIA card inserted into slot 0
[ 6995.414303] pccard: CardBus card inserted into slot 1
[ 7001.306995] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 7001.309563] cs: IO port probe 0x3e0-0x4ff: clean.
[ 7001.310692] cs: IO port probe 0x820-0x8ff: clean.
[ 7001.311671] cs: IO port probe 0xc00-0xcf7: clean.
[ 7001.313222] cs: IO port probe 0xa00-0xaff: excluding 0xa50-0xa57 0xaf8-0xaff
[ 7001.329776] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 7001.332148] cs: IO port probe 0x3e0-0x4ff: clean.
[ 7001.333406] cs: IO port probe 0x820-0x8ff: clean.
[ 7001.334422] cs: IO port probe 0xc00-0xcf7: clean.
[ 7001.335966] cs: IO port probe 0xa00-0xaff: excluding 0xa50-0xa57 0xaf8-0xaff
[ 7001.337237] cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 7001.344527] pcmcia: registering new device pcmcia0.0
[ 7002.058299] ata1: PATA max PIO0 cmd 0x00010320 ctl 0x0001032e bmdma 0x00000000 irq 3
[ 7002.058348] scsi0 : pata_pcmcia
[ 7002.380375] ata1.00: ATAPI, max PIO0
[ 7002.385119] ata1.00: failed to set xfermode (err_mask=0x1)
[ 7002.385199] ata1: failed to recover some devices, retrying in 5 secs
[ 7007.707097] ata1.00: failed to set xfermode (err_mask=0x1)
[ 7007.707179] ata1: failed to recover some devices, retrying in 5 secs
[ 7013.029237] ata1.00: failed to set xfermode (err_mask=0x1)
[ 7013.029314] ata1.00: disabled
...
Umí někdo poradit, v čem se 6.10 liší od 7.04, co se týče podpory PCMCIA, resp. ATAPI? Nevíte jestli zvýrazněné rozdíly v parametrech (0x320 vs. 0x10320 aj.) znamenají něco důležitého?
Pro úplnost: notebook Twinhead P88, Mobile Celeron 333MHz, 192 MB RAM
Díky za každou radu.
[attachment deleted by admin]
Téma: Xubuntu 7.04 nenajde CD-ROM přes PCMCIA (Přečteno 1968 krát)