wifina nejede po hibernace

[ScH0ll_kIll3r]

Dobry den, mam problem s wifi kartou zalozenou na chipsetu RTL8180. Na verzi Feisty Fawn jsem kartu provozoval pres ndiswrapper a vše fungovalo na jedničku, ve verzi Gutsy Gibbon používám nativní drivery rtl8180, protože ndiswrapper začal nějak stávkovat. Všechno frčí, ale když hibernuju nebo uspím notebook, po probuzení wifi karta skenuje, ale ukazuje 0% signalu = nemuzu se pripojit.

Vypis z dmesg

Kód: [Vybrat]

[ 2735.216000] pccard: CardBus card inserted into slot 1
[ 2735.216000] rtl8180: Configuring chip resources
[ 2735.216000] PCI: Enabling device 0000:06:00.0 (0000 -> 0003)
[ 2735.216000] ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 2735.216000] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 2735.216000] rtl8180: Memory mapped space @ 0x2c000000
[ 2735.216000] rtl8180: MAC controller is a RTL8180 (v. F)
[ 2735.216000] rtl8180: This is a CARDBUS NIC
[ 2735.216000] rtl8180: Reported EEPROM chip is a 93c56 (2Kbit)
[ 2735.220000] rtl8180: Card MAC address is 00:12:17:ae:a9:1b
[ 2735.220000] rtl8180: EEPROM version 102
[ 2735.224000] rtl8180: RfParam: 4
[ 2735.224000] rtl8180: WW:Card reports RF frontend by MAXIM.
[ 2735.224000] rtl8180: WW:This driver has EXPERIMENTAL support for this chipset.
[ 2735.224000] rtl8180: WW:use it with care and at your own risk and
[ 2735.224000] rtl8180: WW:**PLEASE** REPORT SUCCESS/INSUCCESS TO andreamrl@tiscali.it
[ 2735.224000] rtl8180: Energy threshold: a
[ 2735.224000] rtl8180: PAPE from CONFIG2: 2
[ 2735.224000] rtl8180: Antenna A is default antenna
[ 2735.224000] rtl8180: Antenna diversity is enabled
[ 2735.224000] rtl8180: Carrier sense 1
[ 2735.224000] rtl8180: 40-bit WEP is NOT supported in hardware
[ 2735.224000] rtl8180: 104-bit WEP is NOT supported in hardware
[ 2735.224000] rtl8180: IRQ 11
[ 2735.224000] rtl8180: Driver probe completed
[ 2735.224000]
[ 2735.492000] rtl8180: Bringing up iface
[ 2735.548000] rtl8180: Card successfully reset
[ 2735.624000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2735.972000] rtl8180: Setting SW wep key
[ 2784.444000] rtl8180: Bringing up iface
[ 2784.500000] rtl8180: Card successfully reset
[ 2784.608000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2796.096000] rtl8180: Setting SW wep key
[ 2798.516000] rtl8180: Setting SW wep key
[ 2798.516000] rtl8180: Setting SW wep key
[ 2798.516000] rtl8180: Setting SW wep key
[ 2798.516000] rtl8180: Setting SW wep key
[ 2798.644000] rtl8180: Setting SW wep key
[ 2803.656000] rtl8180: Setting SW wep key
[ 2808.664000] rtl8180: Setting SW wep key
[ 2813.672000] rtl8180: Setting SW wep key
[ 2818.680000] rtl8180: Setting SW wep key
[ 2821.784000] rtl8180: Bringing up iface
[ 2821.836000] rtl8180: Card successfully reset
[ 2821.940000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2823.692000] rtl8180: Setting SW wep key
[ 2828.700000] rtl8180: Setting SW wep key

Nevíte co stím Děkuji

[Milhouse]

Hodit ten ovladač RTL8180 na blasklist. řešeno na fóru. Já to hold nevím.

[ScH0ll_kIll3r]

Dobre a pouzivat normalne ndiswrapper ?

[Milhouse]

Ne, ten blacklist by měl být jen pro hybernaci. Snad nemelu blbosti, podívám se po tom...

[nettezzaumana]

ue .. resilo se 100x .. do /etc/acpi doplnit do skriptu hibernate na konec reloadnuti modulu pro wifi (modprobe -fr jmeno_modulu && modprobe jmeno_modulu)

[Milhouse]

Ono teoreticky by mělo stačit modul odebrat "sudo rmmod rtl8180" a zase ho spustit "sudo modprobe rtl8180". Pak to dát do skriptu a spuštět po hybernaci.

PS: pozdě Taky si to už musím zapamatovat...

[ScH0ll_kIll3r]

vyřešeno jinak , tenhle driver stal stejne za kulovy, hodil sem ho do blacklistu a jedu pres ndiswrapper