PCTV Hybrid PRO stick

[lukasx]

Zdravim
 uz druhy den snazim rozjet tuto tv kartu a i presto ze navodu jsem nasel spoustu tak se mi nejak nedari a prosim o pomoc:)
zasadni asi bude ze pokud zadam prikaz scan vyhodi mi to tuto chybu:

main:2247: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory

ale vypis dmesg se mi zda ze by to melo byt nainstalovany spravne ikdyz sem linuxovy zacatecnik, proto prosim o radu, predem diky

[ 1571.872000] em28xx #0: Alternate settings: 8
[ 1571.872000] em28xx #0: Alternate setting 0, max size= 0
[ 1571.872000] em28xx #0: Alternate setting 1, max size= 0
[ 1571.872000] em28xx #0: Alternate setting 2, max size= 1448
[ 1571.872000] em28xx #0: Alternate setting 3, max size= 2048
[ 1571.872000] em28xx #0: Alternate setting 4, max size= 2304
[ 1571.872000] em28xx #0: Alternate setting 5, max size= 2580
[ 1571.872000] em28xx #0: Alternate setting 6, max size= 2892
[ 1571.872000] em28xx #0: Alternate setting 7, max size= 3072
[ 1572.272000] input: em2880/em2870 remote control as /class/input/input9
[ 1572.272000] em28xx-input.c: remote control handler attached
[ 1572.272000] attach_inform: eeprom detected.
[ 1572.300000] em28xx #0: i2c eeprom 00: 1a eb 67 95 04 23 26 02 d0 12 5c 03 8e 16 a4 1c
[ 1572.300000] em28xx #0: i2c eeprom 10: 6a 24 27 57 46 07 01 00 00 00 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 02 00 b8 00 00 00 5b e0 00 00
[ 1572.300000] em28xx #0: i2c eeprom 30: 00 00 20 40 20 6e 02 20 10 01 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 24 03 50 00 69 00
[ 1572.300000] em28xx #0: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00
[ 1572.300000] em28xx #0: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 00 00 16 03
[ 1572.300000] em28xx #0: i2c eeprom 90: 50 00 43 00 54 00 56 00 20 00 33 00 33 00 30 00
[ 1572.300000] em28xx #0: i2c eeprom a0: 65 00 00 00 1c 03 30 00 37 00 30 00 34 00 30 00
[ 1572.300000] em28xx #0: i2c eeprom b0: 31 00 39 00 33 00 34 00 30 00 35 00 37 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1572.300000] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1572.300000] EEPROM ID= 0x9567eb1a
[ 1572.300000] Vendor/Product ID= 2304:0226
[ 1572.300000] AC97 audio (5 sample rates)
[ 1572.300000] 500mA max power
[ 1572.300000] Table at 0x27, strings=0x168e, 0x1ca4, 0x246a
[ 1572.300000] tuner 0-0061: chip found @ 0xc2 (em28xx #0)
[ 1572.300000] attach inform (default): detected I2C address c2
[ 1572.300000] /home/lukasx/driver/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
[ 1572.300000] tuner 0x61: Configuration acknowledged
[ 1572.300000] /home/lukasx/driver/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
[ 1572.300000] /home/lukasx/driver/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
[ 1572.300000] /home/lukasx/driver/v4l-dvb-kernel/v4l/tuner-core.c: xc3028 tuner successfully loaded
[ 1572.308000] attach_inform: tvp5150 detected.
[ 1572.380000] tvp5150 0-005c: tvp5150am1 detected.
[ 1572.468000] Loading base firmware: xc3028_init0.i2c.fw
[ 1573.628000] Loading default analogue TV settings: xc3028_BG_PAL_A2_A.i2c.fw
[ 1573.652000] xc3028-tuner.c: firmware 2.7
[ 1573.652000] ANALOG TV REQUEST
[ 1573.656000] em28xx #0: V4L2 VBI device registered as /dev/vbi0
[ 1573.660000] em28xx #0: V4L2 device registered as /dev/video0
[ 1573.660000] em28xx-audio.c: probing for em28x1 non standard usbaudio
[ 1573.660000] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
[ 1573.660000] em28xx #0: Found Pinnacle Hybrid Pro (2)

[Limoto]

A chceš po něm DVB-T, nebo analog?

[lukasx]

no chci nejlepe oboje, ale DVB-T by stacilo

[Limoto]

Potřebuješ balíček mercurial.

Kód: [Vybrat]

hg clone http://mcentral.de/hg/~mrec/v4l-dvb-experimental
cd v4l-dvb-experimantal
make LINUXINCLUDE="-I`pwd`/linux/include -I`pwd`/v4l -Iinclude -include include/linux/autoconf.h"
sudo make installFirmware už asi máš, takže by to po rebootu mělo fungovat.

[lukasx]

no zkusil jsem a porad to samy, 7.10 i 8.04 pls help:)

[Limoto]

A co nefunguje? Analog, DVB-T nebo obojí? Zkus

Kód: [Vybrat]

modprobe em2880-dvb

[lukasx]

no zatim chci zkusit jen dvb analog ani nepotrebuju, kazdopadne jsem fakt linux noobie a mozna je vsechno nainstalovane dobre jen to neumim pouzivat.
zkousel jsem pres kaffeine tam mi to zadny dvb pri prvnim spusteni nenajde a kdyz to zapnu posleze pres menu tak to nejede. no a nekde sem nasel prikaz scan ktery mmi vyhazuje tu error hlasku ktera je v prvnim prispevku

takze pokud by mi byl nekdo schopnej polopaticky popsat nejakej zpusob jak jednoduse vyzkouset jestli to funguje tzn abhy se otevrelo okynko prozacatek klidne se zrnenim byl bych moc rad:)

[lukasx]

jeste dodam ze jsem zkousel zpoustu navodu, jeden sem nasel primo tady na foru, dalsi treba
http://xrob.wordpress.com/2006/12/29/pinnacle-pctv-hybrid-pro-ubuntu-edgy-610-installation/
http://mcentral.de/wiki/index.php5/Main_Page
+ dalsi asi 2 u kterych si ted nepamatuju adresu, kazdopadne u vsech podle vypisu z dmesg to vypada ze by to mohlo fungovat bohuzel to nefunguje:(

[lukasx]

jeste pridam aktualni vypis z dmesg pac ted uz mam ubuntu 8.04


[  294.281668] usb 5-2: new high speed USB device using ehci_hcd and address 3
[  294.421779] usb 5-2: configuration #1 chosen from 1 choice
[  294.674358] Linux video capture interface: v2.00
[  294.737142] em28xx v4l2 driver version 0.0.1 loaded
[  294.737195] em28xx new video device (2304:0226): interface 0, class 255
[  294.737201] em28xx: device is attached to a USB 2.0 bus
[  294.737204] em28xx: you're using the experimental/unstable tree from mcentral.de
[  294.737208] em28xx: there's also a stable tree available but which is limited to
[  294.737212] em28xx: linux <=2.6.19.2
[  294.737215] em28xx: it's fine to use this driver but keep in mind that it will move
[  294.737219] em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as soon as it's
[  294.737223] em28xx: proved to be stable
[  294.737228] em28xx #0: Alternate settings: 8
[  294.737232] em28xx #0: Alternate setting 0, max size= 0
[  294.737235] em28xx #0: Alternate setting 1, max size= 0
[  294.737239] em28xx #0: Alternate setting 2, max size= 1448
[  294.737243] em28xx #0: Alternate setting 3, max size= 2048
[  294.737247] em28xx #0: Alternate setting 4, max size= 2304
[  294.737251] em28xx #0: Alternate setting 5, max size= 2580
[  294.737255] em28xx #0: Alternate setting 6, max size= 2892
[  294.737259] em28xx #0: Alternate setting 7, max size= 3072
[  295.168916] input: em2880/em2870 remote control as /devices/virtual/input/input12
[  295.200787] em28xx-input.c: remote control handler attached
[  295.201768] attach_inform: eeprom detected.
[  295.228859] em28xx #0: i2c eeprom 00: 1a eb 67 95 04 23 26 02 d0 12 5c 03 8e 16 a4 1c
[  295.228879] em28xx #0: i2c eeprom 10: 6a 24 27 57 46 07 01 00 00 00 00 00 00 00 00 00
[  295.228893] em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 02 00 b8 00 00 00 5b e0 00 00
[  295.228908] em28xx #0: i2c eeprom 30: 00 00 20 40 20 6e 02 20 10 01 00 00 00 00 00 00
[  295.228923] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  295.228937] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  295.228951] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 24 03 50 00 69 00
[  295.228966] em28xx #0: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00
[  295.228980] em28xx #0: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 00 00 16 03
[  295.228995] em28xx #0: i2c eeprom 90: 50 00 43 00 54 00 56 00 20 00 33 00 33 00 30 00
[  295.229009] em28xx #0: i2c eeprom a0: 65 00 00 00 1c 03 30 00 37 00 30 00 34 00 30 00
[  295.229024] em28xx #0: i2c eeprom b0: 31 00 39 00 33 00 34 00 30 00 35 00 37 00 00 00
[  295.229038] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  295.229052] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  295.229067] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  295.229081] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  295.229095] EEPROM ID= 0x9567eb1a
[  295.229098] Vendor/Product ID= 2304:0226
[  295.229101] AC97 audio (5 sample rates)
[  295.229104] 500mA max power
[  295.229107] Table at 0x27, strings=0x168e, 0x1ca4, 0x246a
[  295.231723] tuner 0-0061: chip found @ 0xc2 (em28xx #0)
[  295.231756] attach inform (default): detected I2C address c2
[  295.231763] /usr/src/v4l-dvb-experimental/v4l/tuner-core.c: setting tuner callback
[  295.231767] tuner 0x61: Configuration acknowledged
[  295.231771] /usr/src/v4l-dvb-experimental/v4l/tuner-core.c: setting tuner callback
[  295.231840] /usr/src/v4l-dvb-experimental/v4l/xc3028-tuner.c: attach request!
[  295.231845] /usr/src/v4l-dvb-experimental/v4l/tuner-core.c: xc3028 tuner successfully loaded
[  295.237989] attach_inform: tvp5150 detected.
[  295.301215] tvp5150 0-005c: tvp5150am1 detected.
[  295.391796] Loading base firmware: xc3028_init0.i2c.fw
[  296.566068] Loading default analogue TV settings: xc3028_BG_PAL_A2_A.i2c.fw
[  296.603988] xc3028-tuner.c: firmware 2.7
[  296.603999] ANALOG TV REQUEST
[  296.609297] em28xx #0: V4L2 VBI device registered as /dev/vbi0
[  296.611345] em28xx #0: V4L2 device registered as /dev/video0
[  296.611352] em28xx #0: Found Pinnacle Hybrid Pro (2)
[  296.611380] usbcore: registered new interface driver em28xx
[  296.645253] em28xx_audio: no version for "snd_pcm_new" found: kernel tainted.
[  296.681155] em28xx-audio.c: probing for em28x1 non standard usbaudio
[  296.681163] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
[  296.681284] BUG: unable to handle kernel paging request at virtual address 38326d65
[  296.681292] printing eip: f8b02743 *pde = 00000000
[  296.681300] Oops: 0000 [#1] SMP
[  296.681306] Modules linked in: em28xx_audio(F) xc3028_tuner tvp5150 tuner em28xx compat_ioctl32 ir_common videodev v4l2_common v4l1_compat tveeprom i2c_core af_packet radeon drm rfcomm l2cap bluetooth ipv6 uinput ppdev acpi_cpufreq cpufreq_powersave cpufreq_conservative cpufreq_stats cpufreq_userspace cpufreq_ondemand freq_table sbs bay dock container sbshc iptable_filter ip_tables x_tables parport_pc lp parport arc4 ecb blkcipher joydev pcmcia irtty_sir sir_dev nsc_ircc thinkpad_acpi irda nvram crc_ccitt evdev snd_hda_intel snd_pcm_oss snd_mixer_oss battery psmouse serio_raw ac snd_pcm snd_page_alloc snd_hwdep iwl3945 iwlwifi_mac80211 cfg80211 yenta_socket rsrc_nonstatic pcmcia_core snd_seq_dummy sr_mod cdrom snd_seq_oss snd_seq_midi snd_rawmidi video output snd_seq_midi_event snd_seq snd_timer snd_seq_device button snd ata_generic pcspkr iTCO_wdt iTCO_vendor_support soundcore shpchp pci_hotplug intel_agp agpgart ext3 jbd mbcache sg sd_mod ata_piix ahci pata_acpi ehci_hcd uhci_hcd libata scsi_mod usbcore e1000 thermal processor fan fbcon tileblit font bitblit softcursor fuse
[  296.681453]
[  296.681458] Pid: 7004, comm: modprobe Tainted: GF       (2.6.24-14-generic #1)
[  296.681463] EIP: 0060:[<f8b02743>] EFLAGS: 00010246 CPU: 0
[  296.681487] EIP is at snd_pcm_timer_init+0x23/0x170 [snd_pcm]
[  296.681492] EAX: dfdf9000 EBX: 38326d65 ECX: f1a7ddec EDX: 00000000
[  296.681498] ESI: dfdf9000 EDI: dfe49834 EBP: 00000018 ESP: f1a7ddd4
[  296.681502]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  296.681508] Process modprobe (pid: 7004, ti=f1a7c000 task=f1924b40 task.ti=f1a7c000)
[  296.681512] Stack: 00000000 00000001 dfe49a00 00000000 dfe49a00 00000000 00000003 00000000
[  296.681525]        dfcd3c00 00000018 f8a0820c 00000000 dfdf9000 dfe49800 f8afa67f f8b0b92c
[  296.681537]        dfe49800 f1a7de28 dfe49c00 00000001 f8b035f4 436d6370 63304431 ffffff00
[  296.681549] Call Trace:
[  296.681569]  [<f8a0820c>] snd_add_device_sysfs_file+0x3c/0x70 [snd]
[  296.681596]  [<f8afa67f>] snd_pcm_dev_register+0xef/0x200 [snd_pcm]
[  296.681635]  [<f8a0ce4d>] snd_device_register_all+0x2d/0x60 [snd]
[  296.681660]  [<f8a08a1e>] snd_card_register+0x1e/0x320 [snd]
[  296.681694]  [<f8d15178>] em28xx_audio_init+0xf8/0x150 [em28xx_audio]
[  296.681713]  [<f8e292ae>] em28xx_register_extension+0x5e/0xb0 [em28xx]
[  296.681737]  [<c01516b6>] sys_init_module+0x126/0x19c0
[  296.681815]  [<c01053c2>] sysenter_past_esp+0x6b/0xa9
[  296.681832]  [<c013007b>] do_wait+0x43b/0xba0
[  296.681851]  =======================
[  296.681854] Code: 00 00 5b c3 8d 74 26 00 56 89 c6 53 83 ec 30 8b 56 30 c7 44 24 1c 00 00 00 00 8d 4c 24 18 c7 44 24 18 03 00 00 00 8b 18 83 e2 01 <8b> 03 8b 00 89 44 24 20 8b 43 0c 89 44 24 24 8b 46 0c 01 c0 09
[  296.681915] EIP: [<f8b02743>] snd_pcm_timer_init+0x23/0x170 [snd_pcm] SS:ESP 0068:f1a7ddd4
[  296.681939] ---[ end trace e261e4bb1ac3d410 ]---

[Lukasek]

Měl jsi při instalaci ten tuner odpojený???

Mě to sem tam zlobilo,když jsem nechal tuner připojený.

[lukasx]

no mel sem to pri instalaci pripojeny, takze mozna to bude tim, da se nejakym zpusobem odinstalovat vsechny tyhle ovladace firmware atd abychto zkusil bez pripojenyho zarizeni? teda krome reinstalace:)

[Lukasek]

Normálně jsem vzal a znovu zkompiloval ovladače,firmware nech normálně,tam kde je :-).
Pak to normálně restartuj,a mělo by to jet.

[lukasx]

tak porad nic, ted uz mi to pise zase neco jinyho:)

 37.776000] em28xx-video.c: em28xx_set_fmt !V4L_BUF_TYPE_VIDEO_CAPTURE
[   39.432000] eth0: no IPv6 routers present
[  140.424000] em2880-dvb.c: DVB Init
[  140.424000] em2880-dvb.c: unsupported device
[  140.424000] em2880-dvb.c: failed initializing zl10353 DVB-T demodulator
[  140.424000] em2880-dvb.c: retrying with mt352 DVB-T demodulator
[  140.424000] FIXME:em28xx_i2c_send_bytes(1e): write failed:
[  140.424000] ===============================
[  140.424000] 7f
[  140.424000] ================================
[  140.424000] mt352_read_register: readreg error (reg=127, ret==-19)
[  140.424000] em2880-dvb.c: no luck with mt352 demodulator, not attaching em2880-dvb
[  140.424000] em2880-dvb.c: DVB-T demodulator not reachable, did you try "modprobe em28xx device_mode=1"
[  140.424000] Em28xx: Initialized (Em2880 DVB Extension) extension

[Lukasek]

Mno ja jsem tady :

http://forum.ubuntu.cz/index.php?topic=18545.0

sepsal navod na e320,který by ti měl fungovat,zkus jet podle toho,a uvidíme co to udělá
Ještě se zeptám kompiloval jsi experimental nebo kernel driver

[lukasx]

no zkousel sem experimental i kernel se stejnym vysledkem:(( co se toho tvyho navodu tyce tak presne podle toho sem postupoval ale podle zpravy z dmesg dvbt nefunguje muzes sem kdyztak pastnout tvuj vypis z dmsg? pripadne mi napsat co pouzivas na sledovani dvbt signalu? diky

[Lukasek]

PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 5000-500f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e4000000-e5ffffff
  PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1207330148.928:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 937k, total 262144k
vesafb: mode is 800x600x8, linelength=800, pages=6
vesafb: protected mode interface info at c000:e340
vesafb: pmi: set display start = c00ce376, set palette = c00ce3e0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (22 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 169, io base 0x0000d000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:10.1 -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.1, from 5 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 169, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.2, from 5 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 169, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Time: acpi_pm clocksource has been installed.
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usb 1-2: new low speed USB device using uhci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
hda: ST320011A, ATA DISK drive
usb 2-2: new full speed USB device using uhci_hcd and address 2
hdb: WDC WD2500JB-57REA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
usb 2-2: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver hiddev
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input0
input: USB HID v1.10 Keyboard [MOSART Semi. Wireless Keyboard & Mouse] on usb-0000:00:10.0-2
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input1
input,hiddev96: USB HID v1.10 Mouse [MOSART Semi. Wireless Keyboard & Mouse] on usb-0000:00:10.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
hdc: ASUS DRW-1814BL, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.3, from 11 to 9
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 169, io mem 0xe6000000
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-2: USB disconnect, address 2
ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 185
eth0: VIA Rhine II at 0x1e400, 00:30:1b:2e:58:52, IRQ 185.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
hda: cache flushes not supported
 hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hdb: cache flushes supported
 hdb: hdb1
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
usb 4-4: new high speed USB device using ehci_hcd and address 3
usb 4-4: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb 2-2: USB disconnect, address 2
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-2: new low speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input2
input: USB HID v1.10 Keyboard [MOSART Semi. Wireless Keyboard & Mouse] on usb-0000:00:10.0-2
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input3
input,hiddev96: USB HID v1.10 Mouse [MOSART Semi. Wireless Keyboard & Mouse] on usb-0000:00:10.0-2
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input4
Real Time Clock Driver v1.12ac
irda_init()
NET: Registered protocol family 23
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:11.5 to 64
  Vendor: Generic   Model: USB SD Reader     Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: Generic   Model: USB CF Reader     Rev: 1.01
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: Generic   Model: USB SM Reader     Rev: 1.02
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: Generic   Model: USB MS Reader     Rev: 1.03
  Type:   Direct-Access                      ANSI SCSI revision: 00
usb-storage: device scan complete
sd 1:0:0:0: Attached scsi removable disk sda
sd 1:0:0:1: Attached scsi removable disk sdb
sd 1:0:0:2: Attached scsi removable disk sdc
sd 1:0:0:3: Attached scsi removable disk sdd
Adding 1558264k swap on /dev/hda1.  Priority:-1 extents:1 across:1558264k
EXT3 FS on hda2, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Linux video capture interface: v2.00
em28xx v4l2 driver version 0.0.1 loaded
usbcore: registered new driver em28xx
Em28xx: Initialized (Em28xx Audio Extension) extension
Em28xx: Initialized (Em2880 DVB Extension) extension
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201
NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8776  Mon Oct 16 21:56:04 PDT 2006
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
eth0: no IPv6 routers present
usb 4-1: new high speed USB device using ehci_hcd and address 4
usb 4-1: configuration #1 chosen from 1 choice
em28xx new video device (eb1a:2881): interface 0, class 255
em28xx: device is attached to a USB 2.0 bus
em28xx: you're using the experimental/unstable tree from mcentral.de
em28xx: there's also a stable tree available but which is limited to
em28xx: linux <=2.6.19.2
em28xx: it's fine to use this driver but keep in mind that it will move
em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as soon as it's
em28xx: proved to be stable
em28xx #0: Alternate settings: 8
em28xx #0: Alternate setting 0, max size= 0
em28xx #0: Alternate setting 1, max size= 0
em28xx #0: Alternate setting 2, max size= 1448
em28xx #0: Alternate setting 3, max size= 2048
em28xx #0: Alternate setting 4, max size= 2304
em28xx #0: Alternate setting 5, max size= 2580
em28xx #0: Alternate setting 6, max size= 2892
em28xx #0: Alternate setting 7, max size= 3072
i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips
i2c_adapter i2c-2: SMBus Quick command not supported, can't probe for chips
i2c_adapter i2c-3: SMBus Quick command not supported, can't probe for chips
input: em2880/em2870 remote control as /class/input/input5
em28xx-input.c: remote control handler attached
attach_inform: eeprom detected.
em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 81 28 58 12 5c 00 6a 20 6a 00
em28xx #0: i2c eeprom 10: 00 00 04 57 64 57 00 00 60 f4 00 00 02 02 00 00
em28xx #0: i2c eeprom 20: 56 00 01 00 00 00 02 00 b8 00 00 00 5b 1e 00 00
em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 02 00 00 00 00 00 00
em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 20 03 55 00 53 00
em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 38 00 31 00 20 00 56 00
em28xx #0: i2c eeprom 80: 69 00 64 00 65 00 6f 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom e0: 5a 00 55 aa 79 55 54 03 00 17 98 01 00 00 00 00
em28xx #0: i2c eeprom f0: 0c 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
EEPROM ID= 0x9567eb1a
Vendor/Product ID= eb1a:2881
AC97 audio (5 sample rates)
USB Remote wakeup capable
500mA max power
Table at 0x04, strings=0x206a, 0x006a, 0x0000
tuner 4-0061: chip found @ 0xc2 (em28xx #0)
attach inform (default): detected I2C address c2
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
tuner 0x61: Configuration acknowledged
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
/usr/src/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: xc3028 tuner successfully loaded
attach_inform: tvp5150 detected.
tvp5150 4-005c: tvp5150am1 detected.
Loading base firmware: xc3028_init0.i2c.fw
Loading default analogue TV settings: xc3028_BG_PAL_A2_A.i2c.fw
xc3028-tuner.c: firmware 2.7
ANALOG TV REQUEST
em28xx #0: V4L2 VBI device registered as /dev/vbi0
em28xx #0: V4L2 device registered as /dev/video0
em2880-dvb.c: DVB Init
Loading base firmware: xc3028_8MHz_init0.i2c.fw
Loading specific dtv settings: xc3028_DTV6_ATSC_2620.i2c.fw
xc3028-tuner.c: firmware 2.7
Sending extra call for Digital TV!
/usr/src/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
DVB: registering new adapter (em2880 DVB-T)
DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
em28xx #0: Found Pinnacle Hybrid Pro
em28xx audio device (eb1a:2881): interface 1, class 1
em28xx audio device (eb1a:2881): interface 2, class 1
usbcore: registered new driver snd-usb-audio
Loading base firmware: xc3028_8MHz_init0.i2c.fw
Loading specific dtv settings: xc3028_DTV8_2633.i2c.fw
xc3028-tuner.c: firmware 2.7
Sending extra call for Digital TV!
DIGITAL TV REQUEST
usb 4-1: USB disconnect, address 4
em28xx-input.c: remote control handler detached
em28xx #0: disconnecting em28xx#0 video
em28xx #0: V4L2 VIDEO devices /dev/video0 deregistered
em28xx #0: V4L2 VBI devices /dev/vbi0 deregistered
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: releasing Xceive XC3028 tuner!
usb 4-1: new high speed USB device using ehci_hcd and address 5
usb 4-1: configuration #1 chosen from 1 choice
em28xx new video device (eb1a:2881): interface 0, class 255
em28xx: device is attached to a USB 2.0 bus
em28xx: you're using the experimental/unstable tree from mcentral.de
em28xx: there's also a stable tree available but which is limited to
em28xx: linux <=2.6.19.2
em28xx: it's fine to use this driver but keep in mind that it will move
em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as soon as it's
em28xx: proved to be stable
em28xx #0: Alternate settings: 8
em28xx #0: Alternate setting 0, max size= 0
em28xx #0: Alternate setting 1, max size= 0
em28xx #0: Alternate setting 2, max size= 1448
em28xx #0: Alternate setting 3, max size= 2048
em28xx #0: Alternate setting 4, max size= 2304
em28xx #0: Alternate setting 5, max size= 2580
em28xx #0: Alternate setting 6, max size= 2892
em28xx #0: Alternate setting 7, max size= 3072
input: em2880/em2870 remote control as /class/input/input6
em28xx-input.c: remote control handler attached
attach_inform: eeprom detected.
em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 81 28 58 12 5c 00 6a 20 6a 00
em28xx #0: i2c eeprom 10: 00 00 04 57 64 57 00 00 60 f4 00 00 02 02 00 00
em28xx #0: i2c eeprom 20: 56 00 01 00 00 00 02 00 b8 00 00 00 5b 1e 00 00
em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 02 00 00 00 00 00 00
em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 20 03 55 00 53 00
em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 38 00 31 00 20 00 56 00
em28xx #0: i2c eeprom 80: 69 00 64 00 65 00 6f 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom e0: 5a 00 55 aa 79 55 54 03 00 17 98 01 00 00 00 00
em28xx #0: i2c eeprom f0: 0c 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
EEPROM ID= 0x9567eb1a
Vendor/Product ID= eb1a:2881
AC97 audio (5 sample rates)
USB Remote wakeup capable
500mA max power
Table at 0x04, strings=0x206a, 0x006a, 0x0000
tuner 4-0061: chip found @ 0xc2 (em28xx #0)
attach inform (default): detected I2C address c2
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
tuner 0x61: Configuration acknowledged
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
/usr/src/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: xc3028 tuner successfully loaded
attach_inform: tvp5150 detected.
tvp5150 4-005c: tvp5150am1 detected.
Loading base firmware: xc3028_init0.i2c.fw
Loading default analogue TV settings: xc3028_BG_PAL_A2_A.i2c.fw
xc3028-tuner.c: firmware 2.7
ANALOG TV REQUEST
em28xx #0: V4L2 VBI device registered as /dev/vbi0
em28xx #0: V4L2 device registered as /dev/video0
em2880-dvb.c: DVB Init
Loading base firmware: xc3028_8MHz_init0.i2c.fw
Loading specific dtv settings: xc3028_DTV6_ATSC_2620.i2c.fw
xc3028-tuner.c: firmware 2.7
Sending extra call for Digital TV!
/usr/src/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
DVB: registering new adapter (em2880 DVB-T)
DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
em28xx #0: Found Pinnacle Hybrid Pro
em28xx audio device (eb1a:2881): interface 1, class 1
Loading base firmware: xc3028_8MHz_init0.i2c.fw
Loading specific dtv settings: xc3028_DTV8_2633.i2c.fw
xc3028-tuner.c: firmware 2.7
Sending extra call for Digital TV!
DIGITAL TV REQUEST
usb 4-1: USB disconnect, address 5
em28xx-input.c: remote control handler detached
em28xx #0: disconnecting em28xx#0 video
em28xx #0: V4L2 VIDEO devices /dev/video0 deregistered
em28xx #0: V4L2 VBI devices /dev/vbi0 deregistered
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: releasing Xceive XC3028 tuner!
usb 4-1: new high speed USB device using ehci_hcd and address 6
usb 4-1: configuration #1 chosen from 1 choice
em28xx new video device (eb1a:2881): interface 0, class 255
em28xx: device is attached to a USB 2.0 bus
em28xx: you're using the experimental/unstable tree from mcentral.de
em28xx: there's also a stable tree available but which is limited to
em28xx: linux <=2.6.19.2
em28xx: it's fine to use this driver but keep in mind that it will move
em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as soon as it's
em28xx: proved to be stable
em28xx #0: Alternate settings: 8
em28xx #0: Alternate setting 0, max size= 0
em28xx #0: Alternate setting 1, max size= 0
em28xx #0: Alternate setting 2, max size= 1448
em28xx #0: Alternate setting 3, max size= 2048
em28xx #0: Alternate setting 4, max size= 2304
em28xx #0: Alternate setting 5, max size= 2580
em28xx #0: Alternate setting 6, max size= 2892
em28xx #0: Alternate setting 7, max size= 3072
input: em2880/em2870 remote control as /class/input/input7
em28xx-input.c: remote control handler attached
attach_inform: eeprom detected.
em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 81 28 58 12 5c 00 6a 20 6a 00
em28xx #0: i2c eeprom 10: 00 00 04 57 64 57 00 00 60 f4 00 00 02 02 00 00
em28xx #0: i2c eeprom 20: 56 00 01 00 00 00 02 00 b8 00 00 00 5b 1e 00 00
em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 02 00 00 00 00 00 00
em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 20 03 55 00 53 00
em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 38 00 31 00 20 00 56 00
em28xx #0: i2c eeprom 80: 69 00 64 00 65 00 6f 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom e0: 5a 00 55 aa 79 55 54 03 00 17 98 01 00 00 00 00
em28xx #0: i2c eeprom f0: 0c 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
EEPROM ID= 0x9567eb1a
Vendor/Product ID= eb1a:2881
AC97 audio (5 sample rates)
USB Remote wakeup capable
500mA max power
Table at 0x04, strings=0x206a, 0x006a, 0x0000
tuner 4-0061: chip found @ 0xc2 (em28xx #0)
attach inform (default): detected I2C address c2
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
tuner 0x61: Configuration acknowledged
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: setting tuner callback
/usr/src/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
/usr/src/v4l-dvb-kernel/v4l/tuner-core.c: xc3028 tuner successfully loaded
attach_inform: tvp5150 detected.
tvp5150 4-005c: tvp5150am1 detected.
Loading base firmware: xc3028_init0.i2c.fw
Loading default analogue TV settings: xc3028_BG_PAL_A2_A.i2c.fw
xc3028-tuner.c: firmware 2.7
ANALOG TV REQUEST
em28xx #0: V4L2 VBI device registered as /dev/vbi0
em28xx #0: V4L2 device registered as /dev/video0
em2880-dvb.c: DVB Init
Loading base firmware: xc3028_8MHz_init0.i2c.fw
Loading specific dtv settings: xc3028_DTV6_ATSC_2620.i2c.fw
xc3028-tuner.c: firmware 2.7
Sending extra call for Digital TV!
/usr/src/v4l-dvb-kernel/v4l/xc3028-tuner.c: attach request!
DVB: registering new adapter (em2880 DVB-T)
DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
em28xx #0: Found Pinnacle Hybrid Pro
em28xx audio device (eb1a:2881): interface 1, class 1