TV karta HVR 1110 - spojazdnenie analogu

[Mizu165]

Nazdar, mam tuto TV kartu HVR 1110, Ubuntu 8.04, no nejde mi... v /dev/ nie je pripojena, pozera som net, ale vsade su neaktualne navody :/ viete mi poradit?

Tu je lspci:

03:02.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)

Diky

[Martin Kiklhorn]

sudo modprobe saa7134 i2c_scan=1
a co potom vypíše dmesg ?

[Mizu165]

vypisalo:
FATAL: Error inserting saa7134 (/lib/modules/2.6.24-16-generic/ubuntu/media/saa7134/saa7134.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error running install command for saa7134

[Martin Kiklhorn]

pošlete nejdříve výpis

Kód: [Vybrat]

lsmod | grep saa7 pokud se něco vypíše tak

Kód: [Vybrat]

sudo rmmod saa7134_alsa saa7134potom zkuste

Kód: [Vybrat]

sudo modprobe saa7134 i2c_scan=1a pošlite co vypíše

Kód: [Vybrat]

dmesga také

Kód: [Vybrat]

lspci -v

[Mizu165]

skusil som:
lsmod | grep saa7 --nic sa nestalo
potom:
sudo rmmod saa7134_alsa saa7134
ERROR: Module saa7134_alsa does not exist in /proc/modules
ERROR: Module saa7134 does not exist in /proc/modules
potom:
sudo modprobe saa7134 i2c_scan=1
FATAL: Error inserting saa7134 (/lib/modules/2.6.24-16-generic/ubuntu/media/saa7134/saa7134.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error running install command for saa7134
potom:
dmesg

Kód: [Vybrat]

[i]...
[   77.723468] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   94.970344] wlan0: no IPv6 routers present
[  389.376108] saa7134: disagrees about version of symbol videobuf_streamoff
[  389.376115] saa7134: Unknown symbol videobuf_streamoff
[  389.376250] saa7134: disagrees about version of symbol videobuf_poll_stream
[  389.376252] saa7134: Unknown symbol videobuf_poll_stream
[  389.376546] saa7134: disagrees about version of symbol videobuf_dma_free
[  389.376549] saa7134: Unknown symbol videobuf_dma_free
[  389.376654] saa7134: disagrees about version of symbol videobuf_reqbufs
[  389.376656] saa7134: Unknown symbol videobuf_reqbufs
[  389.376896] saa7134: disagrees about version of symbol videobuf_waiton
[  389.376898] saa7134: Unknown symbol videobuf_waiton
[  389.377114] saa7134: disagrees about version of symbol videobuf_dqbuf
[  389.377116] saa7134: Unknown symbol videobuf_dqbuf
[  389.377616] saa7134: disagrees about version of symbol videobuf_stop
[  389.377618] saa7134: Unknown symbol videobuf_stop
[  389.377965] saa7134: Unknown symbol videobuf_queue_pci_init
[  389.378008] saa7134: disagrees about version of symbol videobuf_dma_unmap
[  389.378010] saa7134: Unknown symbol videobuf_dma_unmap
[  389.378057] saa7134: disagrees about version of symbol videobuf_read_stream
[  389.378059] saa7134: Unknown symbol videobuf_read_stream
[  389.378128] saa7134: disagrees about version of symbol videobuf_querybuf
[  389.378130] saa7134: Unknown symbol videobuf_querybuf
[  389.378259] saa7134: disagrees about version of symbol video_unregister_device
[  389.378262] saa7134: Unknown symbol video_unregister_device
[  389.378305] saa7134: disagrees about version of symbol videobuf_qbuf
[  389.378307] saa7134: Unknown symbol videobuf_qbuf
[  389.378419] saa7134: disagrees about version of symbol video_device_alloc
[  389.378421] saa7134: Unknown symbol video_device_alloc
[  389.378464] saa7134: disagrees about version of symbol videobuf_read_one
[  389.378466] saa7134: Unknown symbol videobuf_read_one
[  389.378571] saa7134: disagrees about version of symbol video_register_device
[  389.378573] saa7134: Unknown symbol video_register_device
[  389.378872] saa7134: disagrees about version of symbol videobuf_iolock
[  389.378874] saa7134: Unknown symbol videobuf_iolock
[  389.378976] saa7134: disagrees about version of symbol videobuf_streamon
[  389.378978] saa7134: Unknown symbol videobuf_streamon
[  389.379251] saa7134: disagrees about version of symbol video_device_release
[  389.379253] saa7134: Unknown symbol video_device_release
[  389.379295] saa7134: disagrees about version of symbol videobuf_mmap_mapper
[  389.379297] saa7134: Unknown symbol videobuf_mmap_mapper
[  389.379437] saa7134: disagrees about version of symbol videobuf_cgmbuf
[  389.379439] saa7134: Unknown symbol videobuf_cgmbuf
[  389.379599] saa7134: disagrees about version of symbol videobuf_to_dma
[  389.379601] saa7134: Unknown symbol videobuf_to_dma
[  389.379642] saa7134: disagrees about version of symbol videobuf_mmap_free
[  389.379644] saa7134: Unknown symbol videobuf_mmap_free[/i]potom:
lspci -v

Kód: [Vybrat]

[i]00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>

00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: efa00000-efafffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Capabilities: <access denied>

00:03.0 Communication controller: Intel Corporation 82P965/G965 HECI Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at effff000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>

00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0, IRQ 220
Memory at effc0000 (32-bit, non-prefetchable) [size=128K]
Memory at efffe000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ff00 [size=32]
Capabilities: <access denied>

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at fe00 [size=32]

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at fd00 [size=32]

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 21
Memory at efffd000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0, IRQ 22
Memory at efff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: efc00000-efcfffff
Prefetchable memory behind bridge: 00000000efb00000-00000000efbfffff
Capabilities: <access denied>

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at fc00 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 20
I/O ports at fb00 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 21
I/O ports at fa00 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 19
Memory at efffc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: efe00000-efefffff
Prefetchable memory behind bridge: 00000000efd00000-00000000efdfffff
Capabilities: <access denied>

00:1f.0 ISA bridge: Intel Corporation 82801HH (ICH8DH) LPC Interface Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>

00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 221
I/O ports at f900 [size=8]
I/O ports at f800 [size=4]
I/O ports at f700 [size=8]
I/O ports at f600 [size=4]
I/O ports at f500 [size=32]
Memory at efffb000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: medium devsel, IRQ 11
Memory at efffa000 (32-bit, non-prefetchable) [size=256]
I/O ports at 0500 [size=32]

01:00.0 VGA compatible controller: ATI Technologies Inc RV516 XT Radeon X1600 Series (Primary) (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Unknown device 5920
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at efaf0000 (64-bit, non-prefetchable) [size=64K]
I/O ports at ce00 [size=256]
[virtual] Expansion ROM at efa00000 [disabled] [size=128K]
Capabilities: <access denied>

01:00.1 Display controller: ATI Technologies Inc RV516 XT Radeon X1600 Series (Secondary)
Subsystem: PC Partner Limited Unknown device 5921
Flags: fast devsel
Memory at efae0000 (64-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: <access denied>

03:02.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6700
Flags: bus master, medium devsel, latency 84, IRQ 11
Memory at efeff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>

03:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 64, IRQ 18
Memory at efefe000 (32-bit, non-prefetchable) [size=2K]
Memory at efef8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>[/i]

[Martin Kiklhorn]

Dle http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1110 by to mělo fungovat bez nutnosti cokoliv kompilovat, ale jak je vidět tak nefunguje. Jediné co tam nahrávají extra je firmware pro dvb-t demodulátor, stejně jako zde(zároveň s kompilací driverů z mercurial tree): http://forum.ubuntuusers.de/topic/93694/

Tady http://ubuntuforums.org/showpost.php?p=5017653&postcount=19
se téměř povedlo řešení. Kompilace z mercurial v4l repozitářů, karta se zaregistrovala - ale jen do restartu 
Případně ten samý návod v přehlednější formě je i zde: https://wiki.ubuntu.com/SeifLotfy

Jenom hádám, ale osobně mám podezření na jinou věc - karta teď sdílí přerušení IRQ 11, zkusil bych ji přendat do jiného PCI slotu, přes lspci (nebo lépe lsdev) zkontrolovat zda je na IRQ sama a testnout

Kód: [Vybrat]

sudo modprobe saa7134 i2c_scan=1 znovu.
Když to nepomůže tak to alespoň neuškodí, zkoušel bych pak případně kompilaci z mercurial tree. Nějaká cesta k výsledku určitě povede, zvlášť když je karta uváděna mezi podporovanými v4l.

[Mizu165]

ten novy firmware som si skopiroval, no ja nepotrebujem DVB ale analog. skusil som teda prehodit PCI ale sudo modprobe saa7134 i2c_scan=1 znova hlasi chybu:

Kód: [Vybrat]

FATAL: Error inserting saa7134 (/lib/modules/2.6.24-16-generic/ubuntu/media/saa7134/saa7134.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error running install command for saa7134
tu je lsdev

Kód: [Vybrat]

Device            DMA   IRQ  I/O Ports
------------------------------------------------
0000:00:19.0                 ff00-ff1f
0000:00:1a.0                 fe00-fe1f
0000:00:1a.1                 fd00-fd1f
0000:00:1d.0                 fc00-fc1f
0000:00:1d.1                 fb00-fb1f
0000:00:1d.2                 fa00-fa1f
0000:00:1f.0                 0400-047f 0480-04bf
0000:00:1f.2                 f500-f51f f600-f603 f700-f707 f800-f803 f900-f907
0000:00:1f.3                 0500-051f
0000:01:00.0                   ce00-ceff
acpi                      9
ACPI                           0400-0403   0404-0405   0408-040b   0428-042f
ahci                    221
cascade             4       
dma                          0080-008f
dma1                         0000-001f
dma2                         00c0-00df
e1000                          ff00-ff1f
ehci_hcd:usb6            21
ehci_hcd:usb7            19
eth0                    220
fglrx                    16
floppy              2     6  03f2-03f5 03f7-03f7
fpu                          00f0-00ff
i8042                  1 12
Intel                    22
IO-APIC-edge            3 4
iTCO_wdt                       0460-047f
keyboard                     0060-006f
ohci1394                 18
parport0                  7  0378-037a
PCI                          0cf8-0cff b000-bfff c000-cfff d000-dfff
pic1                         0020-0021
pic2                         00a0-00a1
pnp                          0290-029f   0290-0297 04d0-04d1 0800-087f 0880-088f
rtc                       8  0070-0077
serial                       02f8-02ff 03f8-03ff
timer                     0
timer0                       0040-0043
timer1                       0050-0053
uhci_hcd                       fa00-fa1f   fb00-fb1f   fc00-fc1f   fd00-fd1f   fe00-fe1f
uhci_hcd:usb4            20
vesafb                       03c0-03df
ja nvm... nemohlo sa nieco pokaslat, ked som skusal rozne navody, no v polke som zistil, ze hlasi chybu alebo ze nieco mi neslo tak ako v navode a potom som sa na to vykaslal a zostalo to "rozhadzane"?

[Mizu165]

asi urazim par linuxakov, no nedalo mi to a Ubuntu som preinstaloval (/home/mizu zachoval), pri sudo modprobe saa7134 i2c_scan=1 sa nic nestalo, dmesg sa zmenil, uz to vyzera, ze sa daco loaduje... aspon alsa sound

Kód: [Vybrat]

[    0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 0000000000096000 (usable)
[    0.000000]  BIOS-e820: 0000000000096000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007eee0000 (usable)
[    0.000000]  BIOS-e820: 000000007eee0000 - 000000007eee3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007eee3000 - 000000007eef0000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007eef0000 - 000000007ef00000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] 1134MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f3550
[    0.000000] Entering add_active_range(0, 0, 519904) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   519904
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   519904
[    0.000000] On node 0 totalpages: 519904
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2269 pages used for memmap
[    0.000000]   HighMem zone: 288259 pages, LIFO batch:31
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.4 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F76C0 checksum 0
[    0.000000] ACPI: RSDP 000F76C0, 0014 (r0 ACRSYS)
[    0.000000] ACPI: RSDT 7EEE3040, 0040 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: FACP 7EEE30C0, 0074 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: DSDT 7EEE3180, 4B43 (r1 ACRSYS ACRPRDCT     1000 MSFT  100000E)
[    0.000000] ACPI: FACS 7EEE0000, 0040
[    0.000000] ACPI: HPET 7EEE7E40, 0038 (r1 ACRSYS ACRPRDCT 42302E31 AWRD       98)
[    0.000000] ACPI: SLIC 7EEE7EC0, 0176 (r1 ACRSYS ACRPRDCT 42302E31 AWRD       20)
[    0.000000] ACPI: MCFG 7EEE8080, 003C (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: APIC 7EEE7D40, 0084 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: SSDT 7EEE8100, 0112 (r1  PmRef  Cpu0Ist     3000 INTL 20041203)
[    0.000000] ACPI: SSDT 7EEE8540, 02F1 (r1  PmRef    CpuPm     3000 INTL 20041203)
[    0.000000] ACPI: DMI detected: Acer
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] Processor #1 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 7ef00000:71100000)
[    0.000000] swsusp: Registered nosave memory region: 0000000000096000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515843
[    0.000000] Kernel command line: root=UUID=b32b5e10-3a60-43fc-b6a3-4ee1f70f56eb ro quiet splash
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 2128.045 MHz processor.
[   18.524263] Console: colour VGA+ 80x25
[   18.524266] console [tty0] enabled
[   18.524440] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   18.524654] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   18.598485] Memory: 2049320k/2079616k available (2157k kernel code, 28932k reserved, 998k data, 364k init, 1162112k highmem)
[   18.598491] virtual kernel memory layout:
[   18.598491]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   18.598492]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   18.598493]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   18.598494]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   18.598495]       .init : 0xc041b000 - 0xc0476000   ( 364 kB)
[   18.598496]       .data : 0xc031b5a4 - 0xc0414dc4   ( 998 kB)
[   18.598497]       .text : 0xc0100000 - 0xc031b5a4   (2157 kB)
[   18.598499] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   18.598532] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[   18.598648] hpet clockevent registered
[   18.678619] Calibrating delay using timer specific routine.. 4259.17 BogoMIPS (lpj=8518351)
[   18.678637] Security Framework initialized
[   18.678643] SELinux:  Disabled at boot.
[   18.678654] AppArmor: AppArmor initialized
[   18.678657] Failure registering capabilities with primary security module.
[   18.678664] Mount-cache hash table entries: 512
[   18.678768] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[   18.678775] monitor/mwait feature present.
[   18.678777] using mwait in idle threads.
[   18.678780] CPU: L1 I cache: 32K, L1 D cache: 32K
[   18.678782] CPU: L2 cache: 2048K
[   18.678784] CPU: Physical Processor ID: 0
[   18.678785] CPU: Processor Core ID: 0
[   18.678787] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[   18.678794] Compat vDSO mapped to ffffe000.
[   18.678805] Checking 'hlt' instruction... OK.
[   18.694928] SMP alternatives: switching to UP code
[   18.696245] Early unpacking initramfs... done
[   18.975021] ACPI: Core revision 20070126
[   18.975053] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   18.984742] CPU0: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[   18.984757] SMP alternatives: switching to SMP code
[   18.985351] Booting processor 1/1 eip 3000
[   18.995475] Initializing CPU#1
[   19.074444] Calibrating delay using timer specific routine.. 4256.01 BogoMIPS (lpj=8512023)
[   19.074450] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[   19.074454] monitor/mwait feature present.
[   19.074457] CPU: L1 I cache: 32K, L1 D cache: 32K
[   19.074458] CPU: L2 cache: 2048K
[   19.074460] CPU: Physical Processor ID: 0
[   19.074461] CPU: Processor Core ID: 1
[   19.074462] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[   19.074943] CPU1: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[   19.074959] Total of 2 processors activated (8515.18 BogoMIPS).
[   19.075099] ENABLING IO-APIC IRQs
[   19.075259] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   19.222470] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   19.242478] Brought up 2 CPUs
[   19.242499] CPU0 attaching sched-domain:
[   19.242501]  domain 0: span 03
[   19.242502]   groups: 01 02
[   19.242505] CPU1 attaching sched-domain:
[   19.242506]  domain 0: span 03
[   19.242508]   groups: 02 01
[   19.242693] net_namespace: 64 bytes
[   19.242701] Booting paravirtualized kernel on bare hardware
[   19.243076] Time: 13:47:51  Date: 05/23/08
[   19.243098] NET: Registered protocol family 16
[   19.243254] EISA bus registered
[   19.243257] ACPI: bus type pci registered
[   19.269674] PCI: PCI BIOS revision 3.00 entry at 0xfa020, last bus=3
[   19.269676] PCI: Using configuration type 1
[   19.269677] Setting up standard PCI resources
[   19.270413] mtrr: your CPUs had inconsistent fixed MTRR settings
[   19.270415] mtrr: probably your BIOS does not setup all CPUs.
[   19.270416] mtrr: corrected configuration.
[   19.271720] ACPI: EC: Look up EC in DSDT
[   19.275845] ACPI: Interpreter enabled
[   19.275849] ACPI: (supports S0 S3 S4 S5)
[   19.275862] ACPI: Using IOAPIC for interrupt routing
[   19.281043] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   19.281671] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[   19.281674] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[   19.282109] PCI: Transparent bridge - 0000:00:1e.0
[   19.282132] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   19.282276] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[   19.282354] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[   19.295115] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[   19.295211] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[   19.295306] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[   19.295400] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[   19.295494] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[   19.295588] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[   19.295682] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[   19.295776] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[   19.295886] Linux Plug and Play Support v0.97 (c) Adam Belay
[   19.295911] pnp: PnP ACPI init
[   19.295917] ACPI: bus type pnp registered
[   19.298768] pnpacpi: exceeded the max number of mem resources: 12
[   19.298819] pnp: PnP ACPI: found 16 devices
[   19.298820] ACPI: ACPI bus type pnp unregistered
[   19.298824] PnPBIOS: Disabled by ACPI PNP
[   19.299005] PCI: Using ACPI for IRQ routing
[   19.299007] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   19.342433] NET: Registered protocol family 8
[   19.342435] NET: Registered protocol family 20
[   19.342461] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   19.342465] hpet0: 3 64-bit timers, 14318180 Hz
[   19.343492] AppArmor: AppArmor Filesystem Enabled
[   19.346333] Time: tsc clocksource has been installed.
[   19.346344] Switched to high resolution mode on CPU 0
[   19.346428] Switched to high resolution mode on CPU 1
[   19.359322] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[   19.359325] system 00:01: ioport range 0x290-0x29f has been reserved
[   19.359327] system 00:01: ioport range 0x800-0x87f has been reserved
[   19.359329] system 00:01: ioport range 0x290-0x297 has been reserved
[   19.359331] system 00:01: ioport range 0x880-0x88f has been reserved
[   19.359336] system 00:02: iomem range 0xfe000000-0xfe000fff has been reserved
[   19.359345] system 00:0c: ioport range 0x400-0x4bf could not be reserved
[   19.359350] system 00:0e: iomem range 0xf0000000-0xf3ffffff could not be reserved
[   19.359355] system 00:0f: iomem range 0xd7a00-0xd7fff has been reserved
[   19.359357] system 00:0f: iomem range 0xf0000-0xf7fff could not be reserved
[   19.359359] system 00:0f: iomem range 0xf8000-0xfbfff could not be reserved
[   19.359361] system 00:0f: iomem range 0xfc000-0xfffff could not be reserved
[   19.359363] system 00:0f: iomem range 0xfed00000-0xfed000ff could not be reserved
[   19.359366] system 00:0f: iomem range 0x7eee0000-0x7eefffff could not be reserved
[   19.359368] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[   19.359370] system 00:0f: iomem range 0x100000-0x7eedffff could not be reserved
[   19.359372] system 00:0f: iomem range 0xfec00000-0xfec00fff could not be reserved
[   19.359375] system 00:0f: iomem range 0xfed14000-0xfed1dfff could not be reserved
[   19.359377] system 00:0f: iomem range 0xfed20000-0xfed8ffff could not be reserved
[   19.359379] system 00:0f: iomem range 0xfee00000-0xfee00fff could not be reserved
[   19.389715] PCI: Bridge: 0000:00:01.0
[   19.389717]   IO window: c000-cfff
[   19.389720]   MEM window: efa00000-efafffff
[   19.389722]   PREFETCH window: d0000000-dfffffff
[   19.389725] PCI: Bridge: 0000:00:1c.0
[   19.389727]   IO window: d000-dfff
[   19.389731]   MEM window: efc00000-efcfffff
[   19.389734]   PREFETCH window: efb00000-efbfffff
[   19.389738] PCI: Bridge: 0000:00:1e.0
[   19.389740]   IO window: b000-bfff
[   19.389743]   MEM window: efe00000-efefffff
[   19.389746]   PREFETCH window: efd00000-efdfffff
[   19.389757] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[   19.389761] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   19.389776] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[   19.389780] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   19.389788] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   19.389797] NET: Registered protocol family 2
[   19.427309] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   19.427475] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   19.427811] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   19.427977] TCP: Hash tables configured (established 131072 bind 65536)
[   19.427979] TCP reno registered
[   19.439357] checking if image is initramfs... it is
[   19.989487] Freeing initrd memory: 7708k freed
[   19.990130] audit: initializing netlink socket (disabled)
[   19.990141] audit(1211550471.264:1): initialized
[   19.990315] highmem bounce pool size: 64 pages
[   19.991917] VFS: Disk quotas dquot_6.5.1
[   19.991979] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.992088] io scheduler noop registered
[   19.992089] io scheduler anticipatory registered
[   19.992091] io scheduler deadline registered
[   19.992099] io scheduler cfq registered (default)
[   19.992196] Boot video device is 0000:01:00.0
[   19.992279] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   19.992307] assign_interrupt_mode Found MSI capability
[   19.992331] Allocate Port Service[0000:00:01.0:pcie00]
[   19.992394] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   19.992427] assign_interrupt_mode Found MSI capability
[   19.992455] Allocate Port Service[0000:00:1c.0:pcie00]
[   19.992482] Allocate Port Service[0000:00:1c.0:pcie02]
[   19.992676] isapnp: Scanning for PnP cards...
[   20.345624] isapnp: No Plug & Play device found
[   20.365685] Real Time Clock Driver v1.12ac
[   20.365830] hpet_resources: 0xfed00000 is busy
[   20.365873] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   20.365980] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   20.366089] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.366555] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   20.366737] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.367360] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   20.367413] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   20.367528] PNP: No PS/2 controller found. Probing ports directly.
[   20.367822] serio: i8042 KBD port at 0x60,0x64 irq 1
[   20.367826] serio: i8042 AUX port at 0x60,0x64 irq 12
[   20.381907] mice: PS/2 mouse device common for all mice
[   20.381997] EISA: Probing bus 0 at eisa.0
[   20.382021] EISA: Detected 0 cards.
[   20.382024] cpuidle: using governor ladder
[   20.382025] cpuidle: using governor menu
[   20.382094] NET: Registered protocol family 1
[   20.382115] Using IPI No-Shortcut mode
[   20.382140] registered taskstats version 1
[   20.382222]   Magic number: 8:336:787
[   20.382248]   hash matches device ptyq9
[   20.382264] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   20.382265] EDD information not available.
[   20.382399] Freeing unused kernel memory: 364k freed
[   21.551216] fuse init (API version 7.9)
[   21.562539] ACPI: Fan [FAN] (on)
[   21.567774] ACPI: SSDT 7EEE84B0, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20041203)
[   21.567913] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   21.567922] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   21.569079] ACPI: Thermal Zone [THRM] (17 C)
[   21.673802] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[   21.673806] Copyright (c) 1999-2006 Intel Corporation.
[   21.673845] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 17
[   21.673856] PCI: Setting latency timer of device 0000:00:19.0 to 64
[   21.702996] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:58:a1:3e:72
[   21.723859] usbcore: registered new interface driver usbfs
[   21.723878] usbcore: registered new interface driver hub
[   21.724226] usbcore: registered new device driver usb
[   21.732990] USB Universal Host Controller Interface driver v3.0
[   21.800270] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[   21.800491] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[   21.800501] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[   21.800504] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[   21.800698] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[   21.800724] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fe00
[   21.800833] usb usb1: configuration #1 chosen from 1 choice
[   21.800853] hub 1-0:1.0: USB hub found
[   21.800857] hub 1-0:1.0: 2 ports detected
[   21.902243] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 18
[   21.902254] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[   21.902257] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[   21.902277] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[   21.902300] uhci_hcd 0000:00:1a.1: irq 18, io base 0x0000fd00
[   21.902399] usb usb2: configuration #1 chosen from 1 choice
[   21.902419] hub 2-0:1.0: USB hub found
[   21.902423] hub 2-0:1.0: 2 ports detected
[   21.908467] SCSI subsystem initialized
[   21.914294] libata version 3.00 loaded.
[   21.997161] FDC 0 is a post-1991 82077
[   22.006195] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
[   22.006205] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   22.006208] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   22.006228] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[   22.006252] uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000fc00
[   22.006339] usb usb3: configuration #1 chosen from 1 choice
[   22.006358] hub 3-0:1.0: USB hub found
[   22.006362] hub 3-0:1.0: 2 ports detected
[   22.110147] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
[   22.110157] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   22.110160] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   22.110182] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[   22.110205] uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000fb00
[   22.110295] usb usb4: configuration #1 chosen from 1 choice
[   22.110314] hub 4-0:1.0: USB hub found
[   22.110318] hub 4-0:1.0: 2 ports detected
[   22.142050] usb 1-1: new low speed USB device using uhci_hcd and address 2
[   22.214095] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21
[   22.214103] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   22.214107] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   22.214128] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[   22.214151] uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000fa00
[   22.214240] usb usb5: configuration #1 chosen from 1 choice
[   22.214261] hub 5-0:1.0: USB hub found
[   22.214265] hub 5-0:1.0: 2 ports detected
[   22.315613] usb 1-1: configuration #1 chosen from 1 choice
[   22.318072] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 21
[   22.318084] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[   22.318087] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[   22.318109] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
[   22.322001] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[   22.322005] ehci_hcd 0000:00:1a.7: irq 21, io mem 0xefffd000
[   22.333960] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   22.334038] usb usb6: configuration #1 chosen from 1 choice
[   22.334058] hub 6-0:1.0: USB hub found
[   22.334062] hub 6-0:1.0: 4 ports detected
[   22.436978] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
[   22.436986] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   22.436989] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   22.437006] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[   22.440912] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   22.440916] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xefffc000
[   22.452906] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   22.452991] usb usb7: configuration #1 chosen from 1 choice
[   22.453011] hub 7-0:1.0: USB hub found
[   22.453015] hub 7-0:1.0: 6 ports detected
[   22.556954] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 21 (level, low) -> IRQ 18
[   22.556959] PCI: Setting latency timer of device 0000:03:06.0 to 64
[   22.605852] usb 1-1: USB disconnect, address 2
[   22.606674] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[efefe000-efefe7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[   22.606736] ahci 0000:00:1f.2: version 3.0
[   22.606756] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
[   23.540410] usb 6-2: new high speed USB device using ehci_hcd and address 3
[   23.609398] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
[   23.609401] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part
[   23.609405] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   23.609660] scsi0 : ahci
[   23.609864] scsi1 : ahci
[   23.610006] scsi2 : ahci
[   23.610151] scsi3 : ahci
[   23.610301] scsi4 : ahci
[   23.610455] scsi5 : ahci
[   23.610536] ata1: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb100 irq 221
[   23.610539] ata2: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb180 irq 221
[   23.610541] ata3: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb200 irq 221
[   23.610544] ata4: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb280 irq 221
[   23.610546] ata5: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb300 irq 221
[   23.610548] ata6: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb380 irq 221
[   23.689063] usb 6-2: configuration #1 chosen from 1 choice
[   23.876344] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00016c2000257f78]
[   24.084177] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   24.113875] ata1.00: ATA-7: WDC WD3200JS-00PDB0, 21.00M21, max UDMA/133
[   24.113878] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 1)
[   24.114607] ata1.00: configured for UDMA/133
[   24.424013] ata2: SATA link down (SStatus 0 SControl 300)
[   24.535954] usb 7-4: new high speed USB device using ehci_hcd and address 4
[   24.853900] usb 7-4: configuration #1 chosen from 1 choice
[   24.854187] usbcore: registered new interface driver libusual
[   24.857693] Initializing USB Mass Storage driver...
[   24.899792] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   24.915543] ata3.00: ATA-7: WDC WD3200JS-00PDB0, 21.00M21, max UDMA/133
[   24.915546] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 1)
[   24.916274] ata3.00: configured for UDMA/133
[   25.091698] usb 1-1: new low speed USB device using uhci_hcd and address 3
[   25.227637] ata4: SATA link down (SStatus 0 SControl 300)
[   25.265367] usb 1-1: configuration #1 chosen from 1 choice
[   25.508507] usb 2-2: new full speed USB device using uhci_hcd and address 2
[   25.678845] usb 2-2: configuration #1 chosen from 1 choice
[   25.704422] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   25.859856] ata5.00: ATAPI: Optiarc DVD RW AD-7170S, 1.01, max UDMA/66
[   25.919318] usb 3-2: new low speed USB device using uhci_hcd and address 2
[   26.019786] ata5.00: configured for UDMA/66
[   26.094618] usb 3-2: configuration #1 chosen from 1 choice
[   26.327133] ata6: SATA link down (SStatus 0 SControl 300)
[   26.327235] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200JS-00P 21.0 PQ: 0 ANSI: 5
[   26.327349] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200JS-00P 21.0 PQ: 0 ANSI: 5
[   26.328346] scsi 4:0:0:0: CD-ROM            Optiarc  DVD RW AD-7170S  1.01 PQ: 0 ANSI: 5
[   26.336136] usb 4-1: new low speed USB device using uhci_hcd and address 2
[   26.341014] Driver 'sd' needs updating - please use bus_type methods
[   26.341080] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   26.341090] sd 0:0:0:0: [sda] Write Protect is off
[   26.341092] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.341106] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.341143] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   26.341151] sd 0:0:0:0: [sda] Write Protect is off
[   26.341153] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.341166] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.341168]  sda: sda1 sda2 sda3 <<4>Driver 'sr' needs updating - please use bus_type methods
[   26.368961]  sda5 >
[   26.369056] sd 0:0:0:0: [sda] Attached SCSI disk
[   26.369107] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[   26.369117] sd 2:0:0:0: [sdb] Write Protect is off
[   26.369119] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   26.369133] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.369166] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[   26.369174] sd 2:0:0:0: [sdb] Write Protect is off
[   26.369176] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   26.369188] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.369191]  sdb: sdb1 < sdb5 >
[   26.378771] sd 2:0:0:0: [sdb] Attached SCSI disk
[   26.382841] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.382858] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   26.382875] sr 4:0:0:0: Attached scsi generic sg2 type 5
[   26.389261] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   26.389264] Uniform CD-ROM driver Revision: 3.20
[   26.389313] sr 4:0:0:0: Attached scsi CD-ROM sr0
[   26.514469] usb 4-1: configuration #1 chosen from 1 choice
[   26.543108] scsi6 : SCSI emulation for USB Mass Storage devices
[   26.543557] usb-storage: device found at 3
[   26.543560] usb-storage: waiting for device to settle before scanning
[   26.543595] usbcore: registered new interface driver hiddev
[   26.543635] usbcore: registered new interface driver usb-storage
[   26.543637] USB Mass Storage support registered.
[   26.585843] input: Acer IR Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input1
[   26.595053] input,hiddev96,hidraw0: USB HID v1.10 Keyboard [Acer IR Receiver] on usb-0000:00:1a.0-1
[   26.600608] input: G25 Racing Wheel as /devices/pci0000:00/0000:00:1a.1/usb2/2-2/2-2:1.0/input/input2
[   26.600625] input,hidraw1: USB HID v1.00 Joystick [G25 Racing Wheel] on usb-0000:00:1a.1-2
[   26.613469] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.0/input/input3
[   26.643015] input,hidraw2: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2
[   26.657491] input: LITEON Technology USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb4/4-1/4-1:1.0/input/input4
[   26.666992] input,hidraw3: USB HID v1.10 Keyboard [LITEON Technology USB Keyboard] on usb-0000:00:1d.1-1
[   26.695348] input: LITEON Technology USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb4/4-1/4-1:1.1/input/input5
[   26.714984] input,hidraw4: USB HID v1.10 Device [LITEON Technology USB Keyboard] on usb-0000:00:1d.1-1
[   26.714999] usbcore: registered new interface driver usbhid
[   26.715002] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   26.761132] Attempting manual resume
[   26.761135] swsusp: Resume From Partition 8:5
[   26.761136] PM: Checking swsusp image.
[   26.761230] PM: Resume from disk failed.
[   26.787352] kjournald starting.  Commit interval 5 seconds
[   26.787360] EXT3-fs: mounted filesystem with ordered data mode.
[   31.305692] Linux agpgart interface v0.102
[   31.390582] input: Power Button (FF) as /devices/virtual/input/input6
[   31.403696] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   31.413823] ACPI: Power Button (FF) [PWRF]
[   31.413916] input: Power Button (CM) as /devices/virtual/input/input7
[   31.421920] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   31.441807] ACPI: Power Button (CM) [PWRB]
[   31.573731] usb-storage: device scan complete
[   31.579679] scsi 6:0:0:0: Direct-Access     Generic- Compact Flash    1.00 PQ: 0 ANSI: 0 CCS
[   31.585667] scsi 6:0:0:1: Direct-Access     Generic- SM/xD-Picture    1.00 PQ: 0 ANSI: 0 CCS
[   31.591664] scsi 6:0:0:2: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[   31.597788] scsi 6:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.00 PQ: 0 ANSI: 0 CCS
[   31.599056] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[   31.599091] sd 6:0:0:0: Attached scsi generic sg3 type 0
[   31.600185] sd 6:0:0:1: [sdd] Attached SCSI removable disk
[   31.600218] sd 6:0:0:1: Attached scsi generic sg4 type 0
[   31.601301] sd 6:0:0:2: [sde] Attached SCSI removable disk
[   31.601330] sd 6:0:0:2: Attached scsi generic sg5 type 0
[   31.602426] sd 6:0:0:3: [sdf] Attached SCSI removable disk
[   31.602456] sd 6:0:0:3: Attached scsi generic sg6 type 0
[   31.983856] heci: Intel(R) AMT Management Interface - version 3.1.0.31
[   31.983860] heci: Copyright (c) 2003 - 2007 Intel Corporation.
[   31.983945] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
[   31.983950] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   31.984200] heci: link layer has been established.
[   32.085671] heci: heci driver initialization successful.
[   32.721236] iTCO_vendor_support: vendor-support=0
[   32.727948] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   32.728037] iTCO_wdt: Found a ICH8DH TCO device (Version=2, TCOBASE=0x0460)
[   32.728080] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   32.901778] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   32.901801] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   32.933951] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[   32.988153] Linux video capture interface: v2.00
[   33.056583] input: PC Speaker as /devices/platform/pcspkr/input/input8
[   33.317298] saa7130/34: v4l2 driver version 0.2.14 loaded
[   33.317345] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 18 (level, low) -> IRQ 21
[   33.317352] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 21, latency: 84, mmio: 0xefeff000
[   33.317357] saa7133[0]: subsystem: 0070:6700, board: UNKNOWN/GENERIC [card=0,autodetected]
[   33.317367] saa7133[0]: board init: gpio is 400000
[   33.329418] parport_pc 00:0b: reported by Plug and Play ACPI
[   33.329460] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   33.381625] ACPI: WMI-Acer: Mapper loaded
[   33.416000] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[   33.416013] acer_acpi: No or unsupported WMI interface, unable to load.
[   33.451876] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   33.451885] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[   33.451893] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[   33.451901] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   33.451909] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[   33.451916] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.451924] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.451932] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.453113] saa7133[0]: registered device video0 [v4l2]
[   33.453131] saa7133[0]: registered device vbi0
[   33.467019] saa7134 ALSA driver for DMA sound loaded
[   33.467048] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 21 registered as card -2
[   33.672494] phy0: Selected rate control algorithm 'simple'
[   33.764739] usbcore: registered new interface driver rt73usb
[   34.327478] lp0: using parport0 (interrupt-driven).
[   34.382934] Adding 3911788k swap on /dev/sda5.  Priority:-1 extents:1 across:3911788k
[   34.912668] EXT3 FS on sda2, internal journal
[   36.070731] ip_tables: (C) 2000-2006 Netfilter Core Team
[   36.320464] No dock devices found.
[   37.078804] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[   37.078808] apm: disabled - APM is not SMP safe.
[   37.193147] ppdev: user-space parallel port driver
[   37.257874] audit(1211543289.034:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5834 profile="/usr/sbin/cupsd" namespace="default"
[   38.522093] Bluetooth: Core ver 2.11
[   38.522787] NET: Registered protocol family 31
[   38.522791] Bluetooth: HCI device and connection manager initialized
[   38.522794] Bluetooth: HCI socket layer initialized
[   38.573017] Bluetooth: L2CAP ver 2.9
[   38.573021] Bluetooth: L2CAP socket layer initialized
[   38.601670] Bluetooth: RFCOMM socket layer initialized
[   38.601681] Bluetooth: RFCOMM TTY layer initialized
[   38.601683] Bluetooth: RFCOMM ver 1.8
[   40.241010] [drm] Initialized drm 1.1.0 20060810
[   53.611298] NET: Registered protocol family 10
[   53.611557] lo: Disabled Privacy Extensions
[   53.612058] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   53.612550] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   62.333333] NET: Registered protocol family 17
[   63.516506] wlan0: Initial auth_alg=1
[   63.516513] wlan0: authenticate with AP 00:1b:11:84:fa:4c
[   63.519901] wlan0: RX authentication from 00:1b:11:84:fa:4c (alg=1 transaction=2 status=0)
[   63.519907] wlan0: replying to auth challenge
[   63.523521] wlan0: RX authentication from 00:1b:11:84:fa:4c (alg=1 transaction=4 status=0)
[   63.523526] wlan0: authenticated
[   63.523529] wlan0: associate with AP 00:1b:11:84:fa:4c
[   63.525641] wlan0: RX AssocResp from 00:1b:11:84:fa:4c (capab=0x431 status=0 aid=2)
[   63.525645] wlan0: associated
[   63.525650] wlan0: switched to short barker preamble (BSSID=00:1b:11:84:fa:4c)
[   63.528851] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   80.302410] wlan0: no IPv6 routers present
lsmod | grep saa7 vypise:

Kód: [Vybrat]

saa7134_alsa           15424  0
saa7134               131920  1 saa7134_alsa
compat_ioctl32          2304  1 saa7134
videobuf_dma_sg        14980  2 saa7134_alsa,saa7134
videobuf_core          18820  2 saa7134,videobuf_dma_sg
ir_kbd_i2c             10768  1 saa7134
i2c_core               24832  2 saa7134,ir_kbd_i2c
ir_common              36100  2 saa7134,ir_kbd_i2c
videodev               29440  1 saa7134
v4l2_common            18304  2 saa7134,videodev
v4l1_compat            15492  2 saa7134,videodev
snd_pcm                78596  3 saa7134_alsa,snd_hda_intel,snd_pcm_oss
snd                    56996  18 saa7134_alsa,snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_hwdep,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pokracovanie v dalsom prispevku... uz sa nemesti...

[Mizu165]

potom som dal: sudo rmmod saa7134_alsa saa7134 a sudo modprobe saa7134 i2c_scan=1 a dmesg sa zmenil ku horsiemu.. nejake errory tam hadze:

Kód: [Vybrat]

[    0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 0000000000096000 (usable)
[    0.000000]  BIOS-e820: 0000000000096000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007eee0000 (usable)
[    0.000000]  BIOS-e820: 000000007eee0000 - 000000007eee3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007eee3000 - 000000007eef0000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007eef0000 - 000000007ef00000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] 1134MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f3550
[    0.000000] Entering add_active_range(0, 0, 519904) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   519904
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   519904
[    0.000000] On node 0 totalpages: 519904
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2269 pages used for memmap
[    0.000000]   HighMem zone: 288259 pages, LIFO batch:31
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.4 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F76C0 checksum 0
[    0.000000] ACPI: RSDP 000F76C0, 0014 (r0 ACRSYS)
[    0.000000] ACPI: RSDT 7EEE3040, 0040 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: FACP 7EEE30C0, 0074 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: DSDT 7EEE3180, 4B43 (r1 ACRSYS ACRPRDCT     1000 MSFT  100000E)
[    0.000000] ACPI: FACS 7EEE0000, 0040
[    0.000000] ACPI: HPET 7EEE7E40, 0038 (r1 ACRSYS ACRPRDCT 42302E31 AWRD       98)
[    0.000000] ACPI: SLIC 7EEE7EC0, 0176 (r1 ACRSYS ACRPRDCT 42302E31 AWRD       20)
[    0.000000] ACPI: MCFG 7EEE8080, 003C (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: APIC 7EEE7D40, 0084 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: SSDT 7EEE8100, 0112 (r1  PmRef  Cpu0Ist     3000 INTL 20041203)
[    0.000000] ACPI: SSDT 7EEE8540, 02F1 (r1  PmRef    CpuPm     3000 INTL 20041203)
[    0.000000] ACPI: DMI detected: Acer
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] Processor #1 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 7ef00000:71100000)
[    0.000000] swsusp: Registered nosave memory region: 0000000000096000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515843
[    0.000000] Kernel command line: root=UUID=b32b5e10-3a60-43fc-b6a3-4ee1f70f56eb ro quiet splash
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 2128.045 MHz processor.
[   18.524263] Console: colour VGA+ 80x25
[   18.524266] console [tty0] enabled
[   18.524440] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   18.524654] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   18.598485] Memory: 2049320k/2079616k available (2157k kernel code, 28932k reserved, 998k data, 364k init, 1162112k highmem)
[   18.598491] virtual kernel memory layout:
[   18.598491]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   18.598492]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   18.598493]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   18.598494]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   18.598495]       .init : 0xc041b000 - 0xc0476000   ( 364 kB)
[   18.598496]       .data : 0xc031b5a4 - 0xc0414dc4   ( 998 kB)
[   18.598497]       .text : 0xc0100000 - 0xc031b5a4   (2157 kB)
[   18.598499] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   18.598532] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[   18.598648] hpet clockevent registered
[   18.678619] Calibrating delay using timer specific routine.. 4259.17 BogoMIPS (lpj=8518351)
[   18.678637] Security Framework initialized
[   18.678643] SELinux:  Disabled at boot.
[   18.678654] AppArmor: AppArmor initialized
[   18.678657] Failure registering capabilities with primary security module.
[   18.678664] Mount-cache hash table entries: 512
[   18.678768] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[   18.678775] monitor/mwait feature present.
[   18.678777] using mwait in idle threads.
[   18.678780] CPU: L1 I cache: 32K, L1 D cache: 32K
[   18.678782] CPU: L2 cache: 2048K
[   18.678784] CPU: Physical Processor ID: 0
[   18.678785] CPU: Processor Core ID: 0
[   18.678787] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[   18.678794] Compat vDSO mapped to ffffe000.
[   18.678805] Checking 'hlt' instruction... OK.
[   18.694928] SMP alternatives: switching to UP code
[   18.696245] Early unpacking initramfs... done
[   18.975021] ACPI: Core revision 20070126
[   18.975053] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   18.984742] CPU0: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[   18.984757] SMP alternatives: switching to SMP code
[   18.985351] Booting processor 1/1 eip 3000
[   18.995475] Initializing CPU#1
[   19.074444] Calibrating delay using timer specific routine.. 4256.01 BogoMIPS (lpj=8512023)
[   19.074450] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[   19.074454] monitor/mwait feature present.
[   19.074457] CPU: L1 I cache: 32K, L1 D cache: 32K
[   19.074458] CPU: L2 cache: 2048K
[   19.074460] CPU: Physical Processor ID: 0
[   19.074461] CPU: Processor Core ID: 1
[   19.074462] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[   19.074943] CPU1: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[   19.074959] Total of 2 processors activated (8515.18 BogoMIPS).
[   19.075099] ENABLING IO-APIC IRQs
[   19.075259] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   19.222470] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   19.242478] Brought up 2 CPUs
[   19.242499] CPU0 attaching sched-domain:
[   19.242501]  domain 0: span 03
[   19.242502]   groups: 01 02
[   19.242505] CPU1 attaching sched-domain:
[   19.242506]  domain 0: span 03
[   19.242508]   groups: 02 01
[   19.242693] net_namespace: 64 bytes
[   19.242701] Booting paravirtualized kernel on bare hardware
[   19.243076] Time: 13:47:51  Date: 05/23/08
[   19.243098] NET: Registered protocol family 16
[   19.243254] EISA bus registered
[   19.243257] ACPI: bus type pci registered
[   19.269674] PCI: PCI BIOS revision 3.00 entry at 0xfa020, last bus=3
[   19.269676] PCI: Using configuration type 1
[   19.269677] Setting up standard PCI resources
[   19.270413] mtrr: your CPUs had inconsistent fixed MTRR settings
[   19.270415] mtrr: probably your BIOS does not setup all CPUs.
[   19.270416] mtrr: corrected configuration.
[   19.271720] ACPI: EC: Look up EC in DSDT
[   19.275845] ACPI: Interpreter enabled
[   19.275849] ACPI: (supports S0 S3 S4 S5)
[   19.275862] ACPI: Using IOAPIC for interrupt routing
[   19.281043] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   19.281671] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[   19.281674] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[   19.282109] PCI: Transparent bridge - 0000:00:1e.0
[   19.282132] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   19.282276] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[   19.282354] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[   19.295115] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[   19.295211] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[   19.295306] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[   19.295400] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[   19.295494] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[   19.295588] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[   19.295682] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[   19.295776] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[   19.295886] Linux Plug and Play Support v0.97 (c) Adam Belay
[   19.295911] pnp: PnP ACPI init
[   19.295917] ACPI: bus type pnp registered
[   19.298768] pnpacpi: exceeded the max number of mem resources: 12
[   19.298819] pnp: PnP ACPI: found 16 devices
[   19.298820] ACPI: ACPI bus type pnp unregistered
[   19.298824] PnPBIOS: Disabled by ACPI PNP
[   19.299005] PCI: Using ACPI for IRQ routing
[   19.299007] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   19.342433] NET: Registered protocol family 8
[   19.342435] NET: Registered protocol family 20
[   19.342461] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   19.342465] hpet0: 3 64-bit timers, 14318180 Hz
[   19.343492] AppArmor: AppArmor Filesystem Enabled
[   19.346333] Time: tsc clocksource has been installed.
[   19.346344] Switched to high resolution mode on CPU 0
[   19.346428] Switched to high resolution mode on CPU 1
[   19.359322] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[   19.359325] system 00:01: ioport range 0x290-0x29f has been reserved
[   19.359327] system 00:01: ioport range 0x800-0x87f has been reserved
[   19.359329] system 00:01: ioport range 0x290-0x297 has been reserved
[   19.359331] system 00:01: ioport range 0x880-0x88f has been reserved
[   19.359336] system 00:02: iomem range 0xfe000000-0xfe000fff has been reserved
[   19.359345] system 00:0c: ioport range 0x400-0x4bf could not be reserved
[   19.359350] system 00:0e: iomem range 0xf0000000-0xf3ffffff could not be reserved
[   19.359355] system 00:0f: iomem range 0xd7a00-0xd7fff has been reserved
[   19.359357] system 00:0f: iomem range 0xf0000-0xf7fff could not be reserved
[   19.359359] system 00:0f: iomem range 0xf8000-0xfbfff could not be reserved
[   19.359361] system 00:0f: iomem range 0xfc000-0xfffff could not be reserved
[   19.359363] system 00:0f: iomem range 0xfed00000-0xfed000ff could not be reserved
[   19.359366] system 00:0f: iomem range 0x7eee0000-0x7eefffff could not be reserved
[   19.359368] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[   19.359370] system 00:0f: iomem range 0x100000-0x7eedffff could not be reserved
[   19.359372] system 00:0f: iomem range 0xfec00000-0xfec00fff could not be reserved
[   19.359375] system 00:0f: iomem range 0xfed14000-0xfed1dfff could not be reserved
[   19.359377] system 00:0f: iomem range 0xfed20000-0xfed8ffff could not be reserved
[   19.359379] system 00:0f: iomem range 0xfee00000-0xfee00fff could not be reserved
[   19.389715] PCI: Bridge: 0000:00:01.0
[   19.389717]   IO window: c000-cfff
[   19.389720]   MEM window: efa00000-efafffff
[   19.389722]   PREFETCH window: d0000000-dfffffff
[   19.389725] PCI: Bridge: 0000:00:1c.0
[   19.389727]   IO window: d000-dfff
[   19.389731]   MEM window: efc00000-efcfffff
[   19.389734]   PREFETCH window: efb00000-efbfffff
[   19.389738] PCI: Bridge: 0000:00:1e.0
[   19.389740]   IO window: b000-bfff
[   19.389743]   MEM window: efe00000-efefffff
[   19.389746]   PREFETCH window: efd00000-efdfffff
[   19.389757] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[   19.389761] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   19.389776] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[   19.389780] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   19.389788] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   19.389797] NET: Registered protocol family 2
[   19.427309] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   19.427475] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   19.427811] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   19.427977] TCP: Hash tables configured (established 131072 bind 65536)
[   19.427979] TCP reno registered
[   19.439357] checking if image is initramfs... it is
[   19.989487] Freeing initrd memory: 7708k freed
[   19.990130] audit: initializing netlink socket (disabled)
[   19.990141] audit(1211550471.264:1): initialized
[   19.990315] highmem bounce pool size: 64 pages
[   19.991917] VFS: Disk quotas dquot_6.5.1
[   19.991979] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.992088] io scheduler noop registered
[   19.992089] io scheduler anticipatory registered
[   19.992091] io scheduler deadline registered
[   19.992099] io scheduler cfq registered (default)
[   19.992196] Boot video device is 0000:01:00.0
[   19.992279] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   19.992307] assign_interrupt_mode Found MSI capability
[   19.992331] Allocate Port Service[0000:00:01.0:pcie00]
[   19.992394] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   19.992427] assign_interrupt_mode Found MSI capability
[   19.992455] Allocate Port Service[0000:00:1c.0:pcie00]
[   19.992482] Allocate Port Service[0000:00:1c.0:pcie02]
[   19.992676] isapnp: Scanning for PnP cards...
[   20.345624] isapnp: No Plug & Play device found
[   20.365685] Real Time Clock Driver v1.12ac
[   20.365830] hpet_resources: 0xfed00000 is busy
[   20.365873] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   20.365980] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   20.366089] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.366555] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   20.366737] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.367360] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   20.367413] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   20.367528] PNP: No PS/2 controller found. Probing ports directly.
[   20.367822] serio: i8042 KBD port at 0x60,0x64 irq 1
[   20.367826] serio: i8042 AUX port at 0x60,0x64 irq 12
[   20.381907] mice: PS/2 mouse device common for all mice
[   20.381997] EISA: Probing bus 0 at eisa.0
[   20.382021] EISA: Detected 0 cards.
[   20.382024] cpuidle: using governor ladder
[   20.382025] cpuidle: using governor menu
[   20.382094] NET: Registered protocol family 1
[   20.382115] Using IPI No-Shortcut mode
[   20.382140] registered taskstats version 1
[   20.382222]   Magic number: 8:336:787
[   20.382248]   hash matches device ptyq9
[   20.382264] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   20.382265] EDD information not available.
[   20.382399] Freeing unused kernel memory: 364k freed
[   21.551216] fuse init (API version 7.9)
[   21.562539] ACPI: Fan [FAN] (on)
[   21.567774] ACPI: SSDT 7EEE84B0, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20041203)
[   21.567913] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   21.567922] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   21.569079] ACPI: Thermal Zone [THRM] (17 C)
[   21.673802] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[   21.673806] Copyright (c) 1999-2006 Intel Corporation.
[   21.673845] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 17
[   21.673856] PCI: Setting latency timer of device 0000:00:19.0 to 64
[   21.702996] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:58:a1:3e:72
[   21.723859] usbcore: registered new interface driver usbfs
[   21.723878] usbcore: registered new interface driver hub
[   21.724226] usbcore: registered new device driver usb
[   21.732990] USB Universal Host Controller Interface driver v3.0
[   21.800270] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[   21.800491] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[   21.800501] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[   21.800504] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[   21.800698] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[   21.800724] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fe00
[   21.800833] usb usb1: configuration #1 chosen from 1 choice
[   21.800853] hub 1-0:1.0: USB hub found
[   21.800857] hub 1-0:1.0: 2 ports detected
[   21.902243] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 18
[   21.902254] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[   21.902257] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[   21.902277] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[   21.902300] uhci_hcd 0000:00:1a.1: irq 18, io base 0x0000fd00
[   21.902399] usb usb2: configuration #1 chosen from 1 choice
[   21.902419] hub 2-0:1.0: USB hub found
[   21.902423] hub 2-0:1.0: 2 ports detected
[   21.908467] SCSI subsystem initialized
[   21.914294] libata version 3.00 loaded.
[   21.997161] FDC 0 is a post-1991 82077
[   22.006195] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
[   22.006205] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   22.006208] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   22.006228] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[   22.006252] uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000fc00
[   22.006339] usb usb3: configuration #1 chosen from 1 choice
[   22.006358] hub 3-0:1.0: USB hub found
[   22.006362] hub 3-0:1.0: 2 ports detected
[   22.110147] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
[   22.110157] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   22.110160] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   22.110182] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[   22.110205] uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000fb00
[   22.110295] usb usb4: configuration #1 chosen from 1 choice
[   22.110314] hub 4-0:1.0: USB hub found
[   22.110318] hub 4-0:1.0: 2 ports detected
[   22.142050] usb 1-1: new low speed USB device using uhci_hcd and address 2
[   22.214095] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21
[   22.214103] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   22.214107] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   22.214128] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[   22.214151] uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000fa00
[   22.214240] usb usb5: configuration #1 chosen from 1 choice
[   22.214261] hub 5-0:1.0: USB hub found
[   22.214265] hub 5-0:1.0: 2 ports detected
[   22.315613] usb 1-1: configuration #1 chosen from 1 choice
[   22.318072] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 21
[   22.318084] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[   22.318087] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[   22.318109] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
[   22.322001] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[   22.322005] ehci_hcd 0000:00:1a.7: irq 21, io mem 0xefffd000
[   22.333960] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   22.334038] usb usb6: configuration #1 chosen from 1 choice
[   22.334058] hub 6-0:1.0: USB hub found
[   22.334062] hub 6-0:1.0: 4 ports detected
[   22.436978] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
[   22.436986] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   22.436989] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   22.437006] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[   22.440912] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   22.440916] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xefffc000
[   22.452906] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   22.452991] usb usb7: configuration #1 chosen from 1 choice
[   22.453011] hub 7-0:1.0: USB hub found
[   22.453015] hub 7-0:1.0: 6 ports detected
[   22.556954] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 21 (level, low) -> IRQ 18
[   22.556959] PCI: Setting latency timer of device 0000:03:06.0 to 64
[   22.605852] usb 1-1: USB disconnect, address 2
[   22.606674] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[efefe000-efefe7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[   22.606736] ahci 0000:00:1f.2: version 3.0
[   22.606756] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
[   23.540410] usb 6-2: new high speed USB device using ehci_hcd and address 3
[   23.609398] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
[   23.609401] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part
[   23.609405] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   23.609660] scsi0 : ahci
[   23.609864] scsi1 : ahci
[   23.610006] scsi2 : ahci
[   23.610151] scsi3 : ahci
[   23.610301] scsi4 : ahci
[   23.610455] scsi5 : ahci
[   23.610536] ata1: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb100 irq 221
[   23.610539] ata2: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb180 irq 221
[   23.610541] ata3: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb200 irq 221
[   23.610544] ata4: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb280 irq 221
[   23.610546] ata5: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb300 irq 221
[   23.610548] ata6: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb380 irq 221
[   23.689063] usb 6-2: configuration #1 chosen from 1 choice
[   23.876344] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00016c2000257f78]
[   24.084177] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   24.113875] ata1.00: ATA-7: WDC WD3200JS-00PDB0, 21.00M21, max UDMA/133
[   24.113878] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 1)
[   24.114607] ata1.00: configured for UDMA/133
[   24.424013] ata2: SATA link down (SStatus 0 SControl 300)
[   24.535954] usb 7-4: new high speed USB device using ehci_hcd and address 4
[   24.853900] usb 7-4: configuration #1 chosen from 1 choice
[   24.854187] usbcore: registered new interface driver libusual
[   24.857693] Initializing USB Mass Storage driver...
[   24.899792] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   24.915543] ata3.00: ATA-7: WDC WD3200JS-00PDB0, 21.00M21, max UDMA/133
[   24.915546] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 1)
[   24.916274] ata3.00: configured for UDMA/133
[   25.091698] usb 1-1: new low speed USB device using uhci_hcd and address 3
[   25.227637] ata4: SATA link down (SStatus 0 SControl 300)
[   25.265367] usb 1-1: configuration #1 chosen from 1 choice
[   25.508507] usb 2-2: new full speed USB device using uhci_hcd and address 2
[   25.678845] usb 2-2: configuration #1 chosen from 1 choice
[   25.704422] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   25.859856] ata5.00: ATAPI: Optiarc DVD RW AD-7170S, 1.01, max UDMA/66
[   25.919318] usb 3-2: new low speed USB device using uhci_hcd and address 2
[   26.019786] ata5.00: configured for UDMA/66
[   26.094618] usb 3-2: configuration #1 chosen from 1 choice
[   26.327133] ata6: SATA link down (SStatus 0 SControl 300)
[   26.327235] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200JS-00P 21.0 PQ: 0 ANSI: 5
[   26.327349] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200JS-00P 21.0 PQ: 0 ANSI: 5
[   26.328346] scsi 4:0:0:0: CD-ROM            Optiarc  DVD RW AD-7170S  1.01 PQ: 0 ANSI: 5
[   26.336136] usb 4-1: new low speed USB device using uhci_hcd and address 2
[   26.341014] Driver 'sd' needs updating - please use bus_type methods
[   26.341080] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   26.341090] sd 0:0:0:0: [sda] Write Protect is off
[   26.341092] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.341106] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.341143] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   26.341151] sd 0:0:0:0: [sda] Write Protect is off
[   26.341153] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.341166] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.341168]  sda: sda1 sda2 sda3 <<4>Driver 'sr' needs updating - please use bus_type methods
[   26.368961]  sda5 >
[   26.369056] sd 0:0:0:0: [sda] Attached SCSI disk
[   26.369107] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[   26.369117] sd 2:0:0:0: [sdb] Write Protect is off
[   26.369119] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   26.369133] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.369166] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[   26.369174] sd 2:0:0:0: [sdb] Write Protect is off
[   26.369176] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   26.369188] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.369191]  sdb: sdb1 < sdb5 >
[   26.378771] sd 2:0:0:0: [sdb] Attached SCSI disk
[   26.382841] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.382858] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   26.382875] sr 4:0:0:0: Attached scsi generic sg2 type 5
[   26.389261] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   26.389264] Uniform CD-ROM driver Revision: 3.20
[   26.389313] sr 4:0:0:0: Attached scsi CD-ROM sr0
[   26.514469] usb 4-1: configuration #1 chosen from 1 choice
[   26.543108] scsi6 : SCSI emulation for USB Mass Storage devices
[   26.543557] usb-storage: device found at 3
[   26.543560] usb-storage: waiting for device to settle before scanning
[   26.543595] usbcore: registered new interface driver hiddev
[   26.543635] usbcore: registered new interface driver usb-storage
[   26.543637] USB Mass Storage support registered.
[   26.585843] input: Acer IR Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input1
[   26.595053] input,hiddev96,hidraw0: USB HID v1.10 Keyboard [Acer IR Receiver] on usb-0000:00:1a.0-1
[   26.600608] input: G25 Racing Wheel as /devices/pci0000:00/0000:00:1a.1/usb2/2-2/2-2:1.0/input/input2
[   26.600625] input,hidraw1: USB HID v1.00 Joystick [G25 Racing Wheel] on usb-0000:00:1a.1-2
[   26.613469] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.0/input/input3
[   26.643015] input,hidraw2: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2
[   26.657491] input: LITEON Technology USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb4/4-1/4-1:1.0/input/input4
[   26.666992] input,hidraw3: USB HID v1.10 Keyboard [LITEON Technology USB Keyboard] on usb-0000:00:1d.1-1
[   26.695348] input: LITEON Technology USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb4/4-1/4-1:1.1/input/input5
[   26.714984] input,hidraw4: USB HID v1.10 Device [LITEON Technology USB Keyboard] on usb-0000:00:1d.1-1
[   26.714999] usbcore: registered new interface driver usbhid
[   26.715002] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   26.761132] Attempting manual resume
[   26.761135] swsusp: Resume From Partition 8:5
[   26.761136] PM: Checking swsusp image.
[   26.761230] PM: Resume from disk failed.
[   26.787352] kjournald starting.  Commit interval 5 seconds
[   26.787360] EXT3-fs: mounted filesystem with ordered data mode.
[   31.305692] Linux agpgart interface v0.102
[   31.390582] input: Power Button (FF) as /devices/virtual/input/input6
[   31.403696] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   31.413823] ACPI: Power Button (FF) [PWRF]
[   31.413916] input: Power Button (CM) as /devices/virtual/input/input7
[   31.421920] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   31.441807] ACPI: Power Button (CM) [PWRB]
[   31.573731] usb-storage: device scan complete
[   31.579679] scsi 6:0:0:0: Direct-Access     Generic- Compact Flash    1.00 PQ: 0 ANSI: 0 CCS
[   31.585667] scsi 6:0:0:1: Direct-Access     Generic- SM/xD-Picture    1.00 PQ: 0 ANSI: 0 CCS
[   31.591664] scsi 6:0:0:2: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[   31.597788] scsi 6:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.00 PQ: 0 ANSI: 0 CCS
[   31.599056] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[   31.599091] sd 6:0:0:0: Attached scsi generic sg3 type 0
[   31.600185] sd 6:0:0:1: [sdd] Attached SCSI removable disk
[   31.600218] sd 6:0:0:1: Attached scsi generic sg4 type 0
[   31.601301] sd 6:0:0:2: [sde] Attached SCSI removable disk
[   31.601330] sd 6:0:0:2: Attached scsi generic sg5 type 0
[   31.602426] sd 6:0:0:3: [sdf] Attached SCSI removable disk
[   31.602456] sd 6:0:0:3: Attached scsi generic sg6 type 0
[   31.983856] heci: Intel(R) AMT Management Interface - version 3.1.0.31
[   31.983860] heci: Copyright (c) 2003 - 2007 Intel Corporation.
[   31.983945] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
[   31.983950] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   31.984200] heci: link layer has been established.
[   32.085671] heci: heci driver initialization successful.
[   32.721236] iTCO_vendor_support: vendor-support=0
[   32.727948] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   32.728037] iTCO_wdt: Found a ICH8DH TCO device (Version=2, TCOBASE=0x0460)
[   32.728080] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   32.901778] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   32.901801] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   32.933951] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[   32.988153] Linux video capture interface: v2.00
[   33.056583] input: PC Speaker as /devices/platform/pcspkr/input/input8
[   33.317298] saa7130/34: v4l2 driver version 0.2.14 loaded
[   33.317345] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 18 (level, low) -> IRQ 21
[   33.317352] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 21, latency: 84, mmio: 0xefeff000
[   33.317357] saa7133[0]: subsystem: 0070:6700, board: UNKNOWN/GENERIC [card=0,autodetected]
[   33.317367] saa7133[0]: board init: gpio is 400000
[   33.329418] parport_pc 00:0b: reported by Plug and Play ACPI
[   33.329460] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   33.381625] ACPI: WMI-Acer: Mapper loaded
[   33.416000] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[   33.416013] acer_acpi: No or unsupported WMI interface, unable to load.
[   33.451876] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   33.451885] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[   33.451893] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[   33.451901] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   33.451909] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[   33.451916] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.451924] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.451932] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.453113] saa7133[0]: registered device video0 [v4l2]
[   33.453131] saa7133[0]: registered device vbi0
[   33.467019] saa7134 ALSA driver for DMA sound loaded
[   33.467048] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 21 registered as card -2
[   33.672494] phy0: Selected rate control algorithm 'simple'
[   33.764739] usbcore: registered new interface driver rt73usb
[   34.327478] lp0: using parport0 (interrupt-driven).
[   34.382934] Adding 3911788k swap on /dev/sda5.  Priority:-1 extents:1 across:3911788k
[   34.912668] EXT3 FS on sda2, internal journal
[   36.070731] ip_tables: (C) 2000-2006 Netfilter Core Team
[   36.320464] No dock devices found.
[   37.078804] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[   37.078808] apm: disabled - APM is not SMP safe.
[   37.193147] ppdev: user-space parallel port driver
[   37.257874] audit(1211543289.034:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5834 profile="/usr/sbin/cupsd" namespace="default"
[   38.522093] Bluetooth: Core ver 2.11
[   38.522787] NET: Registered protocol family 31
[   38.522791] Bluetooth: HCI device and connection manager initialized
[   38.522794] Bluetooth: HCI socket layer initialized
[   38.573017] Bluetooth: L2CAP ver 2.9
[   38.573021] Bluetooth: L2CAP socket layer initialized
[   38.601670] Bluetooth: RFCOMM socket layer initialized
[   38.601681] Bluetooth: RFCOMM TTY layer initialized
[   38.601683] Bluetooth: RFCOMM ver 1.8
[   40.241010] [drm] Initialized drm 1.1.0 20060810
[   53.611298] NET: Registered protocol family 10
[   53.611557] lo: Disabled Privacy Extensions
[   53.612058] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   53.612550] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   62.333333] NET: Registered protocol family 17
[   63.516506] wlan0: Initial auth_alg=1
[   63.516513] wlan0: authenticate with AP 00:1b:11:84:fa:4c
[   63.519901] wlan0: RX authentication from 00:1b:11:84:fa:4c (alg=1 transaction=2 status=0)
[   63.519907] wlan0: replying to auth challenge
[   63.523521] wlan0: RX authentication from 00:1b:11:84:fa:4c (alg=1 transaction=4 status=0)
[   63.523526] wlan0: authenticated
[   63.523529] wlan0: associate with AP 00:1b:11:84:fa:4c
[   63.525641] wlan0: RX AssocResp from 00:1b:11:84:fa:4c (capab=0x431 status=0 aid=2)
[   63.525645] wlan0: associated
[   63.525650] wlan0: switched to short barker preamble (BSSID=00:1b:11:84:fa:4c)
[   63.528851] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   80.302410] wlan0: no IPv6 routers present
[ 1108.686511] saa7134 ALSA driver for DMA sound unloaded
[ 1122.901914] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 1122.901960] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 21, latency: 84, mmio: 0xefeff000
[ 1122.901967] saa7133[0]: subsystem: 0070:6700, board: UNKNOWN/GENERIC [card=0,autodetected]
[ 1122.901975] saa7133[0]: board init: gpio is 400000
[ 1123.036846] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[ 1123.036861] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[ 1123.036874] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[ 1123.036888] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 1123.036902] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[ 1123.036916] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1123.036930] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1123.036945] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1123.044841] saa7133[0]: i2c scan: found device @ 0x10  [???]
[ 1123.060837] saa7133[0]: i2c scan: found device @ 0x96  [???]
[ 1123.068833] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[ 1123.077056] saa7133[0]: dsp access error
[ 1123.077058] saa7133[0]: dsp access error
[ 1123.077061] saa7133[0]: dsp access error
[ 1123.077112] saa7133[0]: registered device video0 [v4l2]
[ 1123.077135] saa7133[0]: registered device vbi0
[ 1123.077141] saa7133[0]: dsp access error
[ 1123.077144] saa7133[0]: dsp access error
[ 1123.082154] saa7133[0]: dsp access error
[ 1123.082161] saa7133[0]: dsp access error
[ 1123.094002] saa7134 ALSA driver for DMA sound loaded
[ 1123.094034] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 21 registered as card -2
[ 1123.106253] saa7133[0]: dsp access error
[ 1123.106258] saa7133[0]: dsp access error
[ 1123.654352] saa7133[0]: dsp access error
[ 1123.654359] saa7133[0]: dsp access error
[ 1124.656198] saa7133[0]: dsp access error
[ 1124.656205] saa7133[0]: dsp access error
pokracovanie v dalsom prispevku

[Mizu165]

lspci -v pise:

Kód: [Vybrat]

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>

00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: efa00000-efafffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Capabilities: <access denied>

00:03.0 Communication controller: Intel Corporation 82P965/G965 HECI Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at effff000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>

00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0, IRQ 220
Memory at effc0000 (32-bit, non-prefetchable) [size=128K]
Memory at efffe000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ff00 [size=32]
Capabilities: <access denied>

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at fe00 [size=32]

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at fd00 [size=32]

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 21
Memory at efffd000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, fast devsel, latency 0, IRQ 22
Memory at efff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: efc00000-efcfffff
Prefetchable memory behind bridge: 00000000efb00000-00000000efbfffff
Capabilities: <access denied>

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at fc00 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 20
I/O ports at fb00 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 21
I/O ports at fa00 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 19
Memory at efffc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: efe00000-efefffff
Prefetchable memory behind bridge: 00000000efd00000-00000000efdfffff
Capabilities: <access denied>

00:1f.0 ISA bridge: Intel Corporation 82801HH (ICH8DH) LPC Interface Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>

00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 221
I/O ports at f900 [size=8]
I/O ports at f800 [size=4]
I/O ports at f700 [size=8]
I/O ports at f600 [size=4]
I/O ports at f500 [size=32]
Memory at efffb000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: medium devsel, IRQ 11
Memory at efffa000 (32-bit, non-prefetchable) [size=256]
I/O ports at 0500 [size=32]

01:00.0 VGA compatible controller: ATI Technologies Inc RV516 XT Radeon X1600 Series (Primary) (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Unknown device 5920
Flags: bus master, fast devsel, latency 0, IRQ 5
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at efaf0000 (64-bit, non-prefetchable) [size=64K]
I/O ports at ce00 [size=256]
[virtual] Expansion ROM at efa00000 [disabled] [size=128K]
Capabilities: <access denied>

01:00.1 Display controller: ATI Technologies Inc RV516 XT Radeon X1600 Series (Secondary)
Subsystem: PC Partner Limited Unknown device 5921
Flags: fast devsel
Memory at efae0000 (64-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: <access denied>

03:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6700
Flags: bus master, medium devsel, latency 84, IRQ 21
Memory at efeff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>

03:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 64, IRQ 18
Memory at efefe000 (32-bit, non-prefetchable) [size=2K]
Memory at efef8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
to je vsetko...

[Martin Kiklhorn]

potom som dal: sudo rmmod saa7134_alsa saa7134 a sudo modprobe saa7134 i2c_scan=1 a dmesg sa zmenil ku horsiemu.. nejake errory tam hadze:

Kód: [Vybrat]

[   33.317298] saa7130/34: v4l2 driver version 0.2.14 loaded
[   33.317345] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 18 (level, low) -> IRQ 21
[   33.317352] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 21, latency: 84, mmio: 0xefeff000
[   33.317357] saa7133[0]: subsystem: 0070:6700, board: UNKNOWN/GENERIC [card=0,autodetected]
[   33.317367] saa7133[0]: board init: gpio is 400000
...
[   33.451876] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   33.451885] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[   33.451893] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[   33.451901] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   33.451909] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[   33.451916] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.451924] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.451932] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.453113] saa7133[0]: registered device video0 [v4l2]
[   33.453131] saa7133[0]: registered device vbi0
[   33.467019] saa7134 ALSA driver for DMA sound loaded
[   33.467048] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 21 registered as card -2
...
[ 1108.686511] saa7134 ALSA driver for DMA sound unloaded
[ 1122.901914] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 1122.901960] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 21, latency: 84, mmio: 0xefeff000
[ 1122.901967] saa7133[0]: subsystem: 0070:6700, board: UNKNOWN/GENERIC [card=0,autodetected]
[ 1122.901975] saa7133[0]: board init: gpio is 400000
[ 1123.036846] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[ 1123.036861] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[ 1123.036874] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[ 1123.036888] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 1123.036902] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[ 1123.036916] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1123.036930] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1123.036945] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1123.044841] saa7133[0]: i2c scan: found device @ 0x10  [???]
[ 1123.060837] saa7133[0]: i2c scan: found device @ 0x96  [???]
[ 1123.068833] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[ 1123.077056] saa7133[0]: dsp access error
[ 1123.077058] saa7133[0]: dsp access error
[ 1123.077061] saa7133[0]: dsp access error
[ 1123.077112] saa7133[0]: registered device video0 [v4l2]
[ 1123.077135] saa7133[0]: registered device vbi0
[ 1123.077141] saa7133[0]: dsp access error
[ 1123.077144] saa7133[0]: dsp access error
[ 1123.082154] saa7133[0]: dsp access error
[ 1123.082161] saa7133[0]: dsp access error
[ 1123.094002] saa7134 ALSA driver for DMA sound loaded
[ 1123.094034] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 21 registered as card -2
[ 1123.106253] saa7133[0]: dsp access error
[ 1123.106258] saa7133[0]: dsp access error
[ 1123.654352] saa7133[0]: dsp access error
[ 1123.654359] saa7133[0]: dsp access error
[ 1124.656198] saa7133[0]: dsp access error
[ 1124.656205] saa7133[0]: dsp access error


koukám že
zabrala reinstalace a video se zaregistrovalo hned bez jakýchkoliv úprav
[   33.453113] saa7133[0]: registered device video0 [v4l2]

nebyl rozpoznán typ karty
[   33.317357] saa7133[0]: subsystem: 0070:6700, board: UNKNOWN/GENERIC [card=0,autodetected]
podíval jsem se tedy na seznam aktuálně podporovaných karet s saa7134:
http://linuxtv.org/hg/v4l-dvb/file/tip/linux/Documentation/video4linux/CARDLIST.saa7134
kde je uvedena jako 104
ve zdrojích (apt-get install linux-sources) v /usr/src/linux-source-2.6.24/drivers/media/video/saa7134/7134.h kartu také vidím, takže pokud se v mercurial tree něco závažného neopravuje tak kompilace by neměla být potřeba.
Protože se modul saa7134 zavádí automaticky tak bych doplnil do souboru
/etc/modprobe.d/options
řádek

Kód: [Vybrat]

options saa7134 card=104a restartoval.

Po restartu bych se podíval dmesg zda se něco změnilo.

Zatím neřeším zvuk, ten v aktuálním stavu z karty zřejmě nepoleze ( [   33.467048] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 21 registered as card -2 ), uvidíme po restartu.

buď to pojede nebo pošlite dmesg.

lspci -v pise:

Kód: [Vybrat]

...
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 21
Memory at efffd000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Unknown device 0cef
Flags: bus master, medium devsel, latency 0, IRQ 21
I/O ports at fa00 [size=32]

03:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6700
Flags: bus master, medium devsel, latency 84, IRQ 21
Memory at efeff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>

to je vsetko...

IRQ je sdílené i po přendání do druhého slotu, tentokrát s USB řadičem - [IRQ 21], vadit by to snad nemělo.

[Mizu165]

zda sa mi to krajsie:

Kód: [Vybrat]

[    0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 0000000000096000 (usable)
[    0.000000]  BIOS-e820: 0000000000096000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007eee0000 (usable)
[    0.000000]  BIOS-e820: 000000007eee0000 - 000000007eee3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007eee3000 - 000000007eef0000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007eef0000 - 000000007ef00000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] 1134MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f3550
[    0.000000] Entering add_active_range(0, 0, 519904) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   519904
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   519904
[    0.000000] On node 0 totalpages: 519904
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2269 pages used for memmap
[    0.000000]   HighMem zone: 288259 pages, LIFO batch:31
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.4 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F76C0 checksum 0
[    0.000000] ACPI: RSDP 000F76C0, 0014 (r0 ACRSYS)
[    0.000000] ACPI: RSDT 7EEE3040, 0040 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: FACP 7EEE30C0, 0074 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: DSDT 7EEE3180, 4B43 (r1 ACRSYS ACRPRDCT     1000 MSFT  100000E)
[    0.000000] ACPI: FACS 7EEE0000, 0040
[    0.000000] ACPI: HPET 7EEE7E40, 0038 (r1 ACRSYS ACRPRDCT 42302E31 AWRD       98)
[    0.000000] ACPI: SLIC 7EEE7EC0, 0176 (r1 ACRSYS ACRPRDCT 42302E31 AWRD       20)
[    0.000000] ACPI: MCFG 7EEE8080, 003C (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: APIC 7EEE7D40, 0084 (r1 ACRSYS ACRPRDCT 42302E31 AWRD        0)
[    0.000000] ACPI: SSDT 7EEE8100, 0112 (r1  PmRef  Cpu0Ist     3000 INTL 20041203)
[    0.000000] ACPI: SSDT 7EEE8540, 02F1 (r1  PmRef    CpuPm     3000 INTL 20041203)
[    0.000000] ACPI: DMI detected: Acer
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] Processor #1 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 7ef00000:71100000)
[    0.000000] swsusp: Registered nosave memory region: 0000000000096000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515843
[    0.000000] Kernel command line: root=UUID=b32b5e10-3a60-43fc-b6a3-4ee1f70f56eb ro quiet splash
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 2128.039 MHz processor.
[   18.456686] Console: colour VGA+ 80x25
[   18.456689] console [tty0] enabled
[   18.456863] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   18.457074] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   18.530930] Memory: 2049320k/2079616k available (2157k kernel code, 28932k reserved, 998k data, 364k init, 1162112k highmem)
[   18.530935] virtual kernel memory layout:
[   18.530936]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   18.530937]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   18.530938]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   18.530939]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   18.530940]       .init : 0xc041b000 - 0xc0476000   ( 364 kB)
[   18.530940]       .data : 0xc031b5a4 - 0xc0414dc4   ( 998 kB)
[   18.530941]       .text : 0xc0100000 - 0xc031b5a4   (2157 kB)
[   18.530944] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   18.530977] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[   18.531094] hpet clockevent registered
[   18.611064] Calibrating delay using timer specific routine.. 4259.17 BogoMIPS (lpj=8518352)
[   18.611082] Security Framework initialized
[   18.611088] SELinux:  Disabled at boot.
[   18.611099] AppArmor: AppArmor initialized
[   18.611102] Failure registering capabilities with primary security module.
[   18.611109] Mount-cache hash table entries: 512
[   18.611211] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[   18.611219] monitor/mwait feature present.
[   18.611221] using mwait in idle threads.
[   18.611224] CPU: L1 I cache: 32K, L1 D cache: 32K
[   18.611226] CPU: L2 cache: 2048K
[   18.611228] CPU: Physical Processor ID: 0
[   18.611229] CPU: Processor Core ID: 0
[   18.611230] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[   18.611238] Compat vDSO mapped to ffffe000.
[   18.611249] Checking 'hlt' instruction... OK.
[   18.627374] SMP alternatives: switching to UP code
[   18.628692] Early unpacking initramfs... done
[   18.907449] ACPI: Core revision 20070126
[   18.907481] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   18.917174] CPU0: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[   18.917189] SMP alternatives: switching to SMP code
[   18.917786] Booting processor 1/1 eip 3000
[   18.927909] Initializing CPU#1
[   19.006890] Calibrating delay using timer specific routine.. 4256.01 BogoMIPS (lpj=8512029)
[   19.006896] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[   19.006900] monitor/mwait feature present.
[   19.006902] CPU: L1 I cache: 32K, L1 D cache: 32K
[   19.006904] CPU: L2 cache: 2048K
[   19.006905] CPU: Physical Processor ID: 0
[   19.006906] CPU: Processor Core ID: 1
[   19.006907] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[   19.007363] CPU1: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[   19.007379] Total of 2 processors activated (8515.19 BogoMIPS).
[   19.007518] ENABLING IO-APIC IRQs
[   19.007678] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   19.154913] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   19.174918] Brought up 2 CPUs
[   19.174939] CPU0 attaching sched-domain:
[   19.174941]  domain 0: span 03
[   19.174942]   groups: 01 02
[   19.174945] CPU1 attaching sched-domain:
[   19.174946]  domain 0: span 03
[   19.174947]   groups: 02 01
[   19.175129] net_namespace: 64 bytes
[   19.175137] Booting paravirtualized kernel on bare hardware
[   19.175512] Time: 20:38:28  Date: 05/23/08
[   19.175533] NET: Registered protocol family 16
[   19.175690] EISA bus registered
[   19.175694] ACPI: bus type pci registered
[   19.202932] PCI: PCI BIOS revision 3.00 entry at 0xfa020, last bus=3
[   19.202934] PCI: Using configuration type 1
[   19.202936] Setting up standard PCI resources
[   19.204001] mtrr: your CPUs had inconsistent fixed MTRR settings
[   19.204002] mtrr: probably your BIOS does not setup all CPUs.
[   19.204004] mtrr: corrected configuration.
[   19.205318] ACPI: EC: Look up EC in DSDT
[   19.209403] ACPI: Interpreter enabled
[   19.209408] ACPI: (supports S0 S3 S4 S5)
[   19.209421] ACPI: Using IOAPIC for interrupt routing
[   19.214623] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   19.215254] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[   19.215257] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[   19.215693] PCI: Transparent bridge - 0000:00:1e.0
[   19.215715] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   19.215860] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[   19.215937] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[   19.228709] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[   19.228805] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[   19.228900] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[   19.228994] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[   19.229088] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[   19.229181] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[   19.229275] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[   19.229369] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[   19.229478] Linux Plug and Play Support v0.97 (c) Adam Belay
[   19.229502] pnp: PnP ACPI init
[   19.229508] ACPI: bus type pnp registered
[   19.232358] pnpacpi: exceeded the max number of mem resources: 12
[   19.232409] pnp: PnP ACPI: found 16 devices
[   19.232410] ACPI: ACPI bus type pnp unregistered
[   19.232414] PnPBIOS: Disabled by ACPI PNP
[   19.232600] PCI: Using ACPI for IRQ routing
[   19.232602] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   19.278876] NET: Registered protocol family 8
[   19.278877] NET: Registered protocol family 20
[   19.278903] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   19.278907] hpet0: 3 64-bit timers, 14318180 Hz
[   19.279934] AppArmor: AppArmor Filesystem Enabled
[   19.282776] Time: tsc clocksource has been installed.
[   19.282787] Switched to high resolution mode on CPU 0
[   19.282868] Switched to high resolution mode on CPU 1
[   19.295765] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[   19.295767] system 00:01: ioport range 0x290-0x29f has been reserved
[   19.295769] system 00:01: ioport range 0x800-0x87f has been reserved
[   19.295771] system 00:01: ioport range 0x290-0x297 has been reserved
[   19.295773] system 00:01: ioport range 0x880-0x88f has been reserved
[   19.295779] system 00:02: iomem range 0xfe000000-0xfe000fff has been reserved
[   19.295787] system 00:0c: ioport range 0x400-0x4bf could not be reserved
[   19.295792] system 00:0e: iomem range 0xf0000000-0xf3ffffff could not be reserved
[   19.295797] system 00:0f: iomem range 0xd7a00-0xd7fff has been reserved
[   19.295799] system 00:0f: iomem range 0xf0000-0xf7fff could not be reserved
[   19.295801] system 00:0f: iomem range 0xf8000-0xfbfff could not be reserved
[   19.295803] system 00:0f: iomem range 0xfc000-0xfffff could not be reserved
[   19.295805] system 00:0f: iomem range 0xfed00000-0xfed000ff could not be reserved
[   19.295808] system 00:0f: iomem range 0x7eee0000-0x7eefffff could not be reserved
[   19.295810] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[   19.295812] system 00:0f: iomem range 0x100000-0x7eedffff could not be reserved
[   19.295814] system 00:0f: iomem range 0xfec00000-0xfec00fff could not be reserved
[   19.295817] system 00:0f: iomem range 0xfed14000-0xfed1dfff could not be reserved
[   19.295819] system 00:0f: iomem range 0xfed20000-0xfed8ffff could not be reserved
[   19.295821] system 00:0f: iomem range 0xfee00000-0xfee00fff could not be reserved
[   19.326159] PCI: Bridge: 0000:00:01.0
[   19.326161]   IO window: c000-cfff
[   19.326164]   MEM window: efa00000-efafffff
[   19.326166]   PREFETCH window: d0000000-dfffffff
[   19.326169] PCI: Bridge: 0000:00:1c.0
[   19.326171]   IO window: d000-dfff
[   19.326175]   MEM window: efc00000-efcfffff
[   19.326178]   PREFETCH window: efb00000-efbfffff
[   19.326182] PCI: Bridge: 0000:00:1e.0
[   19.326184]   IO window: b000-bfff
[   19.326187]   MEM window: efe00000-efefffff
[   19.326190]   PREFETCH window: efd00000-efdfffff
[   19.326202] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[   19.326206] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   19.326221] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[   19.326225] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   19.326233] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   19.326241] NET: Registered protocol family 2
[   19.363752] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   19.363920] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   19.364254] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   19.364424] TCP: Hash tables configured (established 131072 bind 65536)
[   19.364426] TCP reno registered
[   19.375796] checking if image is initramfs... it is
[   19.925969] Freeing initrd memory: 7708k freed
[   19.926609] audit: initializing netlink socket (disabled)
[   19.926621] audit(1211575108.268:1): initialized
[   19.926794] highmem bounce pool size: 64 pages
[   19.928395] VFS: Disk quotas dquot_6.5.1
[   19.928456] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.928565] io scheduler noop registered
[   19.928567] io scheduler anticipatory registered
[   19.928568] io scheduler deadline registered
[   19.928577] io scheduler cfq registered (default)
[   19.928674] Boot video device is 0000:01:00.0
[   19.928759] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   19.928787] assign_interrupt_mode Found MSI capability
[   19.928811] Allocate Port Service[0000:00:01.0:pcie00]
[   19.928873] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   19.928907] assign_interrupt_mode Found MSI capability
[   19.928934] Allocate Port Service[0000:00:1c.0:pcie00]
[   19.928961] Allocate Port Service[0000:00:1c.0:pcie02]
[   19.929155] isapnp: Scanning for PnP cards...
[   20.282103] isapnp: No Plug & Play device found
[   20.302155] Real Time Clock Driver v1.12ac
[   20.302313] hpet_resources: 0xfed00000 is busy
[   20.302345] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   20.302452] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   20.302561] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.303027] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   20.303211] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.303833] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   20.303885] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   20.304001] PNP: No PS/2 controller found. Probing ports directly.
[   20.304295] serio: i8042 KBD port at 0x60,0x64 irq 1
[   20.304299] serio: i8042 AUX port at 0x60,0x64 irq 12
[   20.318347] mice: PS/2 mouse device common for all mice
[   20.318436] EISA: Probing bus 0 at eisa.0
[   20.318461] EISA: Detected 0 cards.
[   20.318463] cpuidle: using governor ladder
[   20.318465] cpuidle: using governor menu
[   20.318530] NET: Registered protocol family 1
[   20.318552] Using IPI No-Shortcut mode
[   20.318577] registered taskstats version 1
[   20.318659]   Magic number: 8:425:650
[   20.318676]   hash matches device ptydf
[   20.318701] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   20.318702] EDD information not available.
[   20.318835] Freeing unused kernel memory: 364k freed
[   21.486212] fuse init (API version 7.9)
[   21.497580] ACPI: Fan [FAN] (on)
[   21.502865] ACPI: SSDT 7EEE84B0, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20041203)
[   21.503005] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   21.503013] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   21.504174] ACPI: Thermal Zone [THRM] (19 C)
[   21.771817] usbcore: registered new interface driver usbfs
[   21.771836] usbcore: registered new interface driver hub
[   21.772273] usbcore: registered new device driver usb
[   21.778681] USB Universal Host Controller Interface driver v3.0
[   21.778726] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[   21.778735] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[   21.778738] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[   21.778945] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[   21.778971] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fe00
[   21.779084] usb usb1: configuration #1 chosen from 1 choice
[   21.779104] hub 1-0:1.0: USB hub found
[   21.779107] hub 1-0:1.0: 2 ports detected
[   21.882659] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 17
[   21.882670] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[   21.882673] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[   21.882693] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[   21.882716] uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000fd00
[   21.882807] usb usb2: configuration #1 chosen from 1 choice
[   21.882828] hub 2-0:1.0: USB hub found
[   21.882832] hub 2-0:1.0: 2 ports detected
[   21.887902] SCSI subsystem initialized
[   21.917954] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[   21.917956] Copyright (c) 1999-2006 Intel Corporation.
[   21.918771] libata version 3.00 loaded.
[   21.941222] FDC 0 is a post-1991 82077
[   21.986680] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 18
[   21.986690] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   21.986693] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   21.986712] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[   21.986737] uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000fc00
[   21.986827] usb usb3: configuration #1 chosen from 1 choice
[   21.986846] hub 3-0:1.0: USB hub found
[   21.986850] hub 3-0:1.0: 2 ports detected
[   22.090561] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[   22.090570] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   22.090573] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   22.090594] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[   22.090618] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00
[   22.090712] usb usb4: configuration #1 chosen from 1 choice
[   22.090731] hub 4-0:1.0: USB hub found
[   22.090735] hub 4-0:1.0: 2 ports detected
[   22.122468] usb 1-1: new low speed USB device using uhci_hcd and address 2
[   22.194514] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20
[   22.194524] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   22.194527] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   22.194546] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[   22.194570] uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000fa00
[   22.194664] usb usb5: configuration #1 chosen from 1 choice
[   22.194684] hub 5-0:1.0: USB hub found
[   22.194687] hub 5-0:1.0: 2 ports detected
[   22.294854] usb 1-1: configuration #1 chosen from 1 choice
[   22.298487] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 21
[   22.298497] PCI: Setting latency timer of device 0000:00:19.0 to 64
[   22.327092] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:58:a1:3e:72
[   22.415386] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[   22.415470] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 20
[   22.415478] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[   22.415481] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[   22.415504] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
[   22.419401] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[   22.419406] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xefffd000
[   22.437318] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   22.437410] usb usb6: configuration #1 chosen from 1 choice
[   22.437429] hub 6-0:1.0: USB hub found
[   22.437434] hub 6-0:1.0: 4 ports detected
[   22.537337] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 18
[   22.537345] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   22.537348] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   22.537365] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[   22.541272] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   22.541276] ehci_hcd 0000:00:1d.7: irq 18, io mem 0xefffc000
[   22.553285] usb 1-1: USB disconnect, address 2
[   22.553396] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   22.553475] usb usb7: configuration #1 chosen from 1 choice
[   22.553493] hub 7-0:1.0: USB hub found
[   22.553497] hub 7-0:1.0: 6 ports detected
[   22.657484] ahci 0000:00:1f.2: version 3.0
[   22.657503] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[   23.488840] usb 6-2: new high speed USB device using ehci_hcd and address 3
[   23.638528] usb 6-2: configuration #1 chosen from 1 choice
[   23.661777] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
[   23.661780] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part
[   23.661784] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   23.662015] scsi0 : ahci
[   23.662141] scsi1 : ahci
[   23.662243] scsi2 : ahci
[   23.662351] scsi3 : ahci
[   23.662453] scsi4 : ahci
[   23.662557] scsi5 : ahci
[   23.662636] ata1: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb100 irq 221
[   23.662638] ata2: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb180 irq 221
[   23.662641] ata3: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb200 irq 221
[   23.662643] ata4: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb280 irq 221
[   23.662645] ata5: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb300 irq 221
[   23.662648] ata6: SATA max UDMA/133 abar m2048@0xefffb000 port 0xefffb380 irq 221
[   24.136539] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   24.165022] ata1.00: ATA-7: WDC WD3200JS-00PDB0, 21.00M21, max UDMA/133
[   24.165025] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 1)
[   24.165760] ata1.00: configured for UDMA/133
[   24.244489] usb 7-4: new high speed USB device using ehci_hcd and address 4
[   24.476381] ata2: SATA link down (SStatus 0 SControl 300)
[   24.562431] usb 7-4: configuration #1 chosen from 1 choice
[   24.562697] usbcore: registered new interface driver hiddev
[   24.562739] usbcore: registered new interface driver libusual
[   24.566331] Initializing USB Mass Storage driver...
[   24.800230] usb 1-1: new low speed USB device using uhci_hcd and address 3
[   24.952164] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   24.966761] ata3.00: ATA-7: WDC WD3200JS-00PDB0, 21.00M21, max UDMA/133
[   24.966763] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 1)
[   24.967507] ata3.00: configured for UDMA/133
[   24.973729] usb 1-1: configuration #1 chosen from 1 choice
[   25.216040] usb 3-2: new low speed USB device using uhci_hcd and address 2
[   25.276014] ata4: SATA link down (SStatus 0 SControl 300)
[   25.391393] usb 3-2: configuration #1 chosen from 1 choice
[   25.631848] usb 4-1: new low speed USB device using uhci_hcd and address 2
[   25.751815] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   25.811153] usb 4-1: configuration #1 chosen from 1 choice
[   25.831717] scsi6 : SCSI emulation for USB Mass Storage devices
[   25.831785] usb-storage: device found at 3
[   25.831787] usb-storage: waiting for device to settle before scanning
[   25.872383] input: Acer IR Receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input1
[   25.891769] input,hiddev96,hidraw0: USB HID v1.10 Keyboard [Acer IR Receiver] on usb-0000:00:1a.0-1
[   25.904239] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.0/input/input2
[   25.909232] ata5.00: ATAPI: Optiarc DVD RW AD-7170S, 1.01, max UDMA/66
[   25.919738] input,hidraw1: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2
[   25.934204] input: LITEON Technology USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb4/4-1/4-1:1.0/input/input3
[   25.951716] input,hidraw2: USB HID v1.10 Keyboard [LITEON Technology USB Keyboard] on usb-0000:00:1d.1-1
[   25.981046] input: LITEON Technology USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb4/4-1/4-1:1.1/input/input4
[   25.991695] input,hidraw3: USB HID v1.10 Device [LITEON Technology USB Keyboard] on usb-0000:00:1d.1-1
[   25.991707] usbcore: registered new interface driver usbhid
[   25.991709] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   25.992120] usbcore: registered new interface driver usb-storage
[   25.992123] USB Mass Storage support registered.
[   26.064172] ata5.00: configured for UDMA/66
[   26.375507] ata6: SATA link down (SStatus 0 SControl 300)
[   26.375616] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200JS-00P 21.0 PQ: 0 ANSI: 5
[   26.375730] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200JS-00P 21.0 PQ: 0 ANSI: 5
[   26.376673] scsi 4:0:0:0: CD-ROM            Optiarc  DVD RW AD-7170S  1.01 PQ: 0 ANSI: 5
[   26.376835] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 21 (level, low) -> IRQ 17
[   26.376842] PCI: Setting latency timer of device 0000:03:06.0 to 64
[   26.426557] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]  MMIO=[efefe000-efefe7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[   26.426641] Driver 'sd' needs updating - please use bus_type methods
[   26.426703] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   26.426714] sd 0:0:0:0: [sda] Write Protect is off
[   26.426716] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.426729] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.426767] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   26.426775] sd 0:0:0:0: [sda] Write Protect is off
[   26.426777] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.426790] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.426793]  sda: sda1 sda2 sda3 <<4>Driver 'sr' needs updating - please use bus_type methods
[   26.453404]  sda5 >
[   26.453491] sd 0:0:0:0: [sda] Attached SCSI disk
[   26.453533] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[   26.453543] sd 2:0:0:0: [sdb] Write Protect is off
[   26.453545] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   26.453559] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.453591] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[   26.453599] sd 2:0:0:0: [sdb] Write Protect is off
[   26.453601] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   26.453614] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.453616]  sdb: sdb1 < sdb5 >
[   26.463302] sd 2:0:0:0: [sdb] Attached SCSI disk
[   26.467317] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.467334] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   26.467348] sr 4:0:0:0: Attached scsi generic sg2 type 5
[   26.470402] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   26.470405] Uniform CD-ROM driver Revision: 3.20
[   26.470440] sr 4:0:0:0: Attached scsi CD-ROM sr0
[   26.850354] Attempting manual resume
[   26.850357] swsusp: Resume From Partition 8:5
[   26.850359] PM: Checking swsusp image.
[   26.850466] PM: Resume from disk failed.
[   26.880130] kjournald starting.  Commit interval 5 seconds
[   26.880135] EXT3-fs: mounted filesystem with ordered data mode.
[   27.702987] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00016c2000257f78]
[   30.829558] usb-storage: device scan complete
[   30.835554] scsi 6:0:0:0: Direct-Access     Generic- Compact Flash    1.00 PQ: 0 ANSI: 0 CCS
[   30.841547] scsi 6:0:0:1: Direct-Access     Generic- SM/xD-Picture    1.00 PQ: 0 ANSI: 0 CCS
[   30.847544] scsi 6:0:0:2: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[   30.853668] scsi 6:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.00 PQ: 0 ANSI: 0 CCS
[   30.854935] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[   30.854962] sd 6:0:0:0: Attached scsi generic sg3 type 0
[   30.856054] sd 6:0:0:1: [sdd] Attached SCSI removable disk
[   30.856078] sd 6:0:0:1: Attached scsi generic sg4 type 0
[   30.857179] sd 6:0:0:2: [sde] Attached SCSI removable disk
[   30.857203] sd 6:0:0:2: Attached scsi generic sg5 type 0
[   30.858303] sd 6:0:0:3: [sdf] Attached SCSI removable disk
[   30.858328] sd 6:0:0:3: Attached scsi generic sg6 type 0
[   31.700260] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   31.734110] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   31.773147] Linux agpgart interface v0.102
[   31.820339] input: Power Button (FF) as /devices/virtual/input/input5
[   31.841994] ACPI: Power Button (FF) [PWRF]
[   31.842081] input: Power Button (CM) as /devices/virtual/input/input6
[   31.873985] ACPI: Power Button (CM) [PWRB]
[   31.923118] heci: Intel(R) AMT Management Interface - version 3.1.0.31
[   31.923121] heci: Copyright (c) 2003 - 2007 Intel Corporation.
[   31.923159] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
[   31.923164] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   31.923518] heci: link layer has been established.
[   32.026165] heci: heci driver initialization successful.
[   32.108792] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   32.226849] [fglrx] Maximum main memory to use for locked dma buffers: 1883 MBytes.
[   32.226878] [fglrx] ASYNCIO init succeed!
[   32.227677] [fglrx] PAT is enabled successfully!
[   32.227693] [fglrx] module loaded - fglrx 8.47.3 [Feb 25 2008] on minor 0
[   32.892562] iTCO_vendor_support: vendor-support=0
[   32.933564] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   32.933633] iTCO_wdt: Found a ICH8DH TCO device (Version=2, TCOBASE=0x0460)
[   32.933665] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   33.019664] Linux video capture interface: v2.00
[   33.193414] saa7130/34: v4l2 driver version 0.2.14 loaded
[   33.193467] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 18 (level, low) -> IRQ 20
[   33.193473] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 20, latency: 84, mmio: 0xefeff000
[   33.193479] saa7133[0]: subsystem: 0070:6700, board: Hauppauge WinTV-HVR1110 DVB-T/Hybrid [card=104,insmod option]
[   33.193487] saa7133[0]: board init: gpio is 400000
[   33.328326] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   33.328336] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[   33.328344] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[   33.328352] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   33.328359] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[   33.328367] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.328375] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.328382] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.501226] tuner 0-004b: chip found @ 0x96 (saa7133[0])
[   33.549202] tda8290 0-004b: setting tuner address to 61
[   33.549745] input: PC Speaker as /devices/platform/pcspkr/input/input7
[   33.653157] tuner 0-004b: type set to tda8290+75a
[   33.701622] tda8290 0-004b: setting tuner address to 61
[   33.710700] parport_pc 00:0b: reported by Plug and Play ACPI
[   33.710743] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   33.777015] ACPI: WMI-Acer: Mapper loaded
[   33.805294] tuner 0-004b: type set to tda8290+75a
[   33.808854] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[   33.808868] acer_acpi: No or unsupported WMI interface, unable to load.
[   33.809263] saa7133[0]: registered device video0 [v4l2]
[   33.809281] saa7133[0]: registered device vbi0
[   33.809300] saa7133[0]: registered device radio0
[   33.828908] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   33.828926] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   33.850216] saa7134 ALSA driver for DMA sound loaded
[   33.850241] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 20 registered as card -2
[   33.861934] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[   33.906542] DVB: registering new adapter (saa7133[0])
[   33.906546] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
[   33.976005] tda1004x: setting up plls for 48MHz sampling clock
[   33.991815] phy0: Selected rate control algorithm 'simple'
[   34.090159] usbcore: registered new interface driver rt73usb
[   34.520178] lp0: using parport0 (interrupt-driven).
[   34.575652] Adding 3911788k swap on /dev/sda5.  Priority:-1 extents:1 across:3911788k
[   35.106276] EXT3 FS on sda2, internal journal
[   36.146866] ip_tables: (C) 2000-2006 Netfilter Core Team
[   36.250960] tda1004x: timeout waiting for DSP ready
[   36.291937] tda1004x: found firmware revision 94 -- invalid
[   36.291939] tda1004x: trying to boot from eeprom
[   36.438768] No dock devices found.
[   37.271838] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[   37.271842] apm: disabled - APM is not SMP safe.
[   37.444164] ppdev: user-space parallel port driver
[   37.508825] audit(1211567926.056:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5545 profile="/usr/sbin/cupsd" namespace="default"
[   38.613868] tda1004x: timeout waiting for DSP ready
[   38.653849] tda1004x: found firmware revision 94 -- invalid
[   38.653852] tda1004x: waiting for firmware upload...
[   51.104117] tda1004x: found firmware revision 20 -- ok
[   54.796011] Bluetooth: Core ver 2.11
[   54.796469] NET: Registered protocol family 31
[   54.796472] Bluetooth: HCI device and connection manager initialized
[   54.796475] Bluetooth: HCI socket layer initialized
[   54.822501] Bluetooth: L2CAP ver 2.9
[   54.822505] Bluetooth: L2CAP socket layer initialized
[   54.874678] Bluetooth: RFCOMM socket layer initialized
[   54.875125] Bluetooth: RFCOMM TTY layer initialized
[   54.875129] Bluetooth: RFCOMM ver 1.8
[   55.833926] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   56.864582] [fglrx] Reserve Block - 0 offset =  0Xfffb000 length = 0X5000
[   56.864588] [fglrx] Reserve Block - 1 offset =  0X0 length = 0X1000000
[   56.864591] [fglrx] Reserve Block - 2 offset =  0Xffbb000 length = 0X40000
[   56.902074] [fglrx] interrupt source 20008000 successfully enabled
[   56.902079] [fglrx] enable ID = 0x00000008
[   56.902089] [fglrx] Receive enable interrupt message with irqEnableMask: 20008000
[   68.779390] NET: Registered protocol family 10
[   68.779743] lo: Disabled Privacy Extensions
[   68.780320] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   68.780910] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   77.193763] NET: Registered protocol family 17
[   78.345648] wlan0: Initial auth_alg=1
[   78.345654] wlan0: authenticate with AP 00:1b:11:84:fa:4c
[   78.350034] wlan0: RX authentication from 00:1b:11:84:fa:4c (alg=1 transaction=2 status=0)
[   78.350038] wlan0: replying to auth challenge
[   78.357404] wlan0: RX authentication from 00:1b:11:84:fa:4c (alg=1 transaction=4 status=0)
[   78.357408] wlan0: authenticated
[   78.357411] wlan0: associate with AP 00:1b:11:84:fa:4c
[   78.359530] wlan0: RX AssocResp from 00:1b:11:84:fa:4c (capab=0x431 status=0 aid=1)
[   78.359534] wlan0: associated
[   78.359538] wlan0: switched to short barker preamble (BSSID=00:1b:11:84:fa:4c)
[   78.363011] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   98.038504] wlan0: no IPv6 routers present
no sudo modprobe saa7134 i2c_scan=1 nic neurobi... ako inak sa da zistit, ci karta ide? alebo aky je dobry soft na pozeranie TV? Skusal som nieco s VLC ale nic neslo...

[Martin Kiklhorn]

zda sa mi to krajsie:

Kód: [Vybrat]

[   33.019664] Linux video capture interface: v2.00
[   33.193414] saa7130/34: v4l2 driver version 0.2.14 loaded
[   33.193467] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 18 (level, low) -> IRQ 20
[   33.193473] saa7133[0]: found at 0000:03:03.0, rev: 209, irq: 20, latency: 84, mmio: 0xefeff000
[   33.193479] saa7133[0]: subsystem: 0070:6700, board: Hauppauge WinTV-HVR1110 DVB-T/Hybrid [card=104,insmod option]
[   33.193487] saa7133[0]: board init: gpio is 400000
[   33.328326] saa7133[0]: i2c eeprom 00: 70 00 00 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   33.328336] saa7133[0]: i2c eeprom 10: ff ff ff 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[   33.328344] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 a3 ff ff ff ff
[   33.328352] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   33.328359] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[   33.328367] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.328375] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.328382] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   33.501226] tuner 0-004b: chip found @ 0x96 (saa7133[0])
[   33.549202] tda8290 0-004b: setting tuner address to 61
[   33.549745] input: PC Speaker as /devices/platform/pcspkr/input/input7
[   33.653157] tuner 0-004b: type set to tda8290+75a
[   33.701622] tda8290 0-004b: setting tuner address to 61
[   33.710700] parport_pc 00:0b: reported by Plug and Play ACPI
[   33.710743] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   33.777015] ACPI: WMI-Acer: Mapper loaded
[   33.805294] tuner 0-004b: type set to tda8290+75a
[   33.808854] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[   33.808868] acer_acpi: No or unsupported WMI interface, unable to load.
[   33.809263] saa7133[0]: registered device video0 [v4l2]
[   33.809281] saa7133[0]: registered device vbi0
[   33.809300] saa7133[0]: registered device radio0
[   33.828908] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   33.828926] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   33.850216] saa7134 ALSA driver for DMA sound loaded
[   33.850241] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 20 registered as card -2
[   33.861934] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[   33.906542] DVB: registering new adapter (saa7133[0])
[   33.906546] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
[   33.976005] tda1004x: setting up plls for 48MHz sampling clock
[   36.250960] tda1004x: timeout waiting for DSP ready
[   36.291937] tda1004x: found firmware revision 94 -- invalid
[   36.291939] tda1004x: trying to boot from eeprom
[   38.613868] tda1004x: timeout waiting for DSP ready
[   38.653849] tda1004x: found firmware revision 94 -- invalid
[   38.653852] tda1004x: waiting for firmware upload...
[   51.104117] tda1004x: found firmware revision 20 -- ok

no sudo modprobe saa7134 i2c_scan=1 nic neurobi... ako inak sa da zistit, ci karta ide? alebo aky je dobry soft na pozeranie TV? Skusal som nieco s VLC ale nic neslo...

tohle
sudo modprobe saa7134 i2c_scan=1
uz zkouset nemusíš - karta je systému známá, má zaregistrovány odpovídající zařízení (budou teď už existovat
/dev/video0
/dev/vbi0
/dev/radio0
/dev/dvb/adapter0....

pořád to vidím špatně se zvukem - ale mohu se mýlit
[   33.850241] saa7133[0]/alsa: saa7133[0] at 0xefeff000 irq 20 registered as card -2

na přehrávání je toho spousta, jednoduše by mohl fungovat totem, gxine, xawtv, fbtv ...

[Mizu165]

ktory prehravac vie pracovat s analogovym signalom?? v toteme a aj v gxine je iba DVB

[Martin Kiklhorn]

ktory prehravac vie pracovat s analogovym signalom?? v toteme a aj v gxine je iba DVB

co ten xawtv ?

pokud nejde spustit tak napsat v terminálu xawtv a on si postěžuje co mu chybí...

[Mizu165]

konzola po zadani xawtv:

Kód: [Vybrat]

This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.24-16-generic)
xinerama 0: 1680x1050+0+0
Warning: Cannot convert string "-*-ledfixed-medium-r-*--39-*-*-*-c-*-*-*" to type FontStruct
inak, ked spustim xaw, tak mi vypne obraz... pomoze az Crtl+Alt+F4 a potom zase prepnutie Alt+F7...ale to je asi nepodstatne. Xaw inak nic nerobi... cierne okno.

[Martin Kiklhorn]

na xawtv je postavený motv, a co to tady vůbec řešíme, vždyť je toho spousta na wiki:
http://wiki.ubuntu.cz/Analogov%C3%A1%20TV

[Mizu165]

Super, uz som cez kdetv nasiel programy, dokonca funguje aj teletext, ale obraz a zvuk nikde hlasi:
Unable to grab video.
Video display is not possible with the current plugin configuration. Try playing with the configuration options of the V4L2 plugin.
lenze aj ked hocico nastavim, nejde to, skusal som aj ine softy... nic, zrejme ta karta pouziva nejaky divny format, alebo co

[Martin Kiklhorn]

zkuste tvtime (také na wiki) - saa7134 je mezi podporovanými http://tvtime.sourceforge.net/cards.html#saa7134
případně zkuste doinstalovat nějaké kodeky a balíky - přehrávání videa myslím závisí na přítomnosti gstreamer nebo xine, zkuste si najít mezi nimi rozdíly (mělo by to být podobné jako u audia oss nebo alsa). Doufám že se nemýlím.

pokud by byl problém se zvukem, jak už jsem tipoval minule, tak ten se řeší zde http://en.opensuse.org/Hauppauge_HVR-1110_TV-DVB_card (přesměrování přes sox) nebo zde (pro ubuntu - používá alsu - imho vhodnější)  http://www.linuxtv.org/v4lwiki/index.php/Saa7134-alsa viz řádek sudo modprobe saa7134-alsa index=1,2,3,4

   

[sepasepa]

Super, uz som cez kdetv nasiel programy, dokonca funguje aj teletext, ale obraz a zvuk nikde hlasi:
Unable to grab video.
Video display is not possible with the current plugin configuration. Try playing with the configuration options of the V4L2 plugin.
lenze aj ked hocico nastavim, nejde to, skusal som aj ine softy... nic, zrejme ta karta pouziva nejaky divny format, alebo co

Zdravím, tahle hláška je mi trochu povědomá. Mám stejnou TV kartu (momentálně nepoužívám) . Kamarád , který linuxu rozumí více než já , se s tím trápil docela dlouho.  Co si pamatuju tak zvuk musel zprovoznit přes ten "sox" jak tady odkazuje kiklhorn. A u obrazu byl problém s ovladačema grafiky ATI.  Ale už si nepamatuju jak to vyřešil. Každopádně karta fungovala.
Jinak teď mám v PC jinou TV kartu (chip Conexant CX2388xx) , bohužel mi taky nefunguje.   Opět problém s ATInou.  "xvoutput: No XVIDEO port found which supports YUY2 images."  Zkoušel jsem to řešit sám, ale nějak mi to nejde, vždycky to skončí totálním pádem systému.     
Takže čekám jak dopadnete Vy s tou TV kartou, abych se ji pokusil zprovoznit podle vás.

[Mizu165]

nemusite mi vykat, ale fajn by bolo opytat sa kamarata, ako to vyriesil... hm este ma napada, ze zapojim monitor na onboard grafiku a ATI proste vypojim a skusim tu kartu

[Mizu165]

zkuste tvtime (také na wiki) - saa7134 je mezi podporovanými http://tvtime.sourceforge.net/cards.html#saa7134
případně zkuste doinstalovat nějaké kodeky a balíky - přehrávání videa myslím závisí na přítomnosti gstreamer nebo xine, zkuste si najít mezi nimi rozdíly (mělo by to být podobné jako u audia oss nebo alsa). Doufám že se nemýlím.

pokud by byl problém se zvukem, jak už jsem tipoval minule, tak ten se řeší zde http://en.opensuse.org/Hauppauge_HVR-1110_TV-DVB_card (přesměrování přes sox) nebo zde (pro ubuntu - používá alsu - imho vhodnější)  http://www.linuxtv.org/v4lwiki/index.php/Saa7134-alsa viz řádek sudo modprobe saa7134-alsa index=1,2,3,4

   

bohuzial, tvtime mi nejde proste spustim, blikne okno a hned zmizne (compiz vypnuty), ani v procesoch som nic s tvtime nenasiel myslim, ze ta karta alebo PC robi vsetko preto, aby som ju nespojazdnil ]-/ vseliake gstreamer-y mam aj xine mam... nic..
EDIT: skusil som vypnut ATI ovladace, reboot, no aj tak tvtime nejde a kdetv tiez hlasi tu hlasku...
EDIT2: zmenil sa xawtv prikaz:

Kód: [Vybrat]

This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.24-16-generic)
xinerama 0: 1680x1050+0+0
xinerama 1: 1680x1050+0+0
X Error of failed request:  XF86DGANoDirectVideoMode
  Major opcode of failed request:  136 (XFree86-DGA)
  Minor opcode of failed request:  1 (XF86DGAGetVideoLL)
  Serial number of failed request:  68
  Current serial number in output stream:  68asi je to nepodstatne, ale niekoho by mohlo nieco napadnut

[Martin Kiklhorn]

Kód: [Vybrat]

This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.24-16-generic)
xinerama 0: 1680x1050+0+0
xinerama 1: 1680x1050+0+0
X Error of failed request:  XF86DGANoDirectVideoMode
  Major opcode of failed request:  136 (XFree86-DGA)
  Minor opcode of failed request:  1 (XF86DGAGetVideoLL)
  Serial number of failed request:  68
  Current serial number in output stream:  68asi je to nepodstatne, ale niekoho by mohlo nieco napadnut

zkuste ještě

Kód: [Vybrat]

xawtv -nodga -device /dev/video0

[Mizu165]

vzdavam to. uz viem koli comu sa za windows plati (alebo teoreticky preco): je to proste no problem system. Ubuntu som si nainstaloval zo zvedavosti, najprv som pokukoval po Mandrive, potom po openSUSE, no vyhralo Ubuntu. Ubuntu a ine distra su skvele systemy, ak clovek nechce minat peniaze na windows, alebo nema dobry HW. Ak mate dobry HW, tak je mala sanca, ze tam budete pouzivat linux, to je fakt. Kto by mal v PC super vykonnu grafiku a linux, ked proste na linux nie su hry, ovladace? A tiez je to bieda zo softom znamym z windowsu. Ja viem ze to vobec nie je chyba linuxu, ale soft. a hardw. spolocnosti, no oni to predsa nerobia naschval - im sa to jednoducho neoplati a cele je to v zacarovanom kruhu. Z Ubuntu a Gnome mam fajn pocit, je to skvely, rychly system, velmi dobre modifikovatelny. No dost ma stve, ze mi tam nejde ta TV karta, mozno je to problem ATI, kto vie. Dalsia vec je, ze si proste nepripojim ipod touch. Na druhu stranu SSH je v ubuntu skvele, no skoda, ze pesnicky cez to nezosynchronizujem... Dalsia vec je Delphi, ktore nutne potrebujem do skoly. Ubuntu ma velmi potesilo, ked som mal uz od zaciatku nastavene rozlisenie 1680*1050 a dokonca mi fungoval USB wifi prijimac . Tiez instalacia ATI ovladacov bola extremne lahka. No celkovo ma Ubuntu pre mna viac nevyhod ako vyhod. Fakt vravim pravdu ked poviem, ze pri Ubuntu 8.04 som sa narozculoval viac ako s XP a Vistou dokopy. Nemusite mi to verit, ale s konkretne mojim HW je to proste tak. A presne koli tomuto sa plati za windows. Zan sa neplati akoze iba za system, ale aj za lahku instalaciu HW ovladacov, za nalepky "Vista ready" na skoro kazdom baleni HW, mate istotu, ze kazdy HW na tom windowse pojde. Linux a MAC su dva extremy, uplne odlisne cenovo a aj lahkostou spravovania a instalacie. A windows je zlata stredna cesta. Ale myslim, ze pre toho, kto nepotrebuje nove hry, uplne kompatibilne dokumenty .doc, TV kartu (i ked vela ich pobezi), je linux vhodnejsim riesenim ako windows. Neznasam fanatikov, ktori su tupo "oddani" svojmu systemu, alebo prehladacu atd. a vyvolavaju flame war. No kedze tu na fore ziadni tupi windowsaci zrejme nie su, tak sa chcem opytat ako je to svami, windowsom a Ubuntu. S cim ste mali viac starosti? Preco pouzivate Ubuntu? Koli tomu ze necete platit a proste vam staci, alebo z principu, ktory vlastne ani nema logiku?
Kazdy kto ma (alebo mal) dualboot si urcite vela krat povedal, ze naco su mu 2 systemy. V mojom pripade to bolo tak, ze som pouzival iba Ubuntu, ked som ho nainstaloval. Stale som tam riesil nejake veci ohladne HW a tiez ma bavilo ho spoznavat a tak na win neostal cas. Niekomu sa to bude zdat divne, ale windows sa mi esta nepokazil tak, ze som musel reinstalovat, zato Ubuntu ano (akoze neslo spustit, nemyslim nejaky bezny problem). Teraz zapinam windows castejsie, Ubuntu nie je to, co ziadam od OS.. Ano, ja viem ze to nie je chyba Ubuntu, ze mi nejde synch. ipod, TV karta, hry, atd.. ale je to zacarovany kruh a nikto s tym nic nemoze momentalne urobit. Z Ubuntu mi budu chybat jeho fajn funkcie, je ich strasne vela, urcite asi viete co. Na druhu stranu, v Ubuntu (v Gnome) mi chybali niektore funkcie z visty. Niektore funkcie boli boli lepsie ako vo windowse, niektore horsie, a niektore inak spravena a nedaju sa porovnavat. Je to o tom, co sa cloveku paci a vyhovuje mu. Ak u niekoho doma uvidim linux a uzivatel bude stastny, tak budem len rad a nebudem ho predviedcat na ine, pretoze windows urcite pozna a zrejme mu nevyhovuje. A ked je niekto stastny z winom, no nehra hry, atd.., tak mu rad ukazem Ubuntu, nech spozna aj inu alternativu, mozno sa mu zapaci viac. Mam kamosa, ktory ma NB a tam Vistu. Absolutne je mu vista na nic a NB pouziva iba na chat a taketo veci. Tu by sa ubuntu extremne hodilo no on je voci novym (inym) technologiam flegmaticky. Skoda. Zacarovany kruh tu je, niekoho to stve a ineho nie. Vista podla mna nie je tak hrozny system ako vsade pisu "ti ktori na nom denne pracuju" myslene ironicky. Som ochotny cakat tych par sekund navyse pri starte a mat lahsi zivot. To je moj pohlad na OS, ak chcete, tak sa vyjadrite.

Dakujem vsetkym, ktori sa mi pokusali pomoct s TV kartou, nakoniec teda chyta signal (teletext ide) no obraz a zvuk nie.

[Martin Kiklhorn]

Nevzdávejte to chvilku před cílem

Linux používám od listopadu, všechno bylo pro mne nové a ze začátku jsem se smířil s tím že linux většina výrobců hardwaru ignoruje.
Kdybych si stavěl nové PC tak budu kupovat HW podle toho zda je podporován linuxem (tedy již je podpora v jádru) - v tom případě to prostě funguje. Nebo projdu internet zda se ten konkrétní hardware podařilo někomu rozchodit složitější cestou (někdy o dost složitější).
Samozřejmě HW který již mám nevyhodím, pokud se jej někomu zprovoznit podařilo tak vím že nakonec u mne pojede také a něco se při jeho rozchození opět naučím. Dneska mi prostě chodí na několika počítačích vše (zatím kromě jedné express card hybridní karty) včetně hodně nestandartního hw. A i když něco nikomu nechodí tak někdy stačí jen najít oznámení že na podpoře toho hw se již pracuje.

Pokud je problém s ATI tak zkuste pro nainstalování ovladačů envy, třeba to pomůže.