Nechce mi citat USB kluce

[playerx8]

DObry den, po zastrceny USb kluca do booku mi ho nechce nacitat..teda, nacita ho, no nechce ho otvorit
napise : nepodarilo sa pripojit umiestnenie, subor sa neda pripojit..

Za rychlu pomoc vopred dakujem

[arrange]

Zasuň USB, chvíli počkej, a pak sem dej výpisy z

Kód: [Vybrat]

lsusb
dmesg | tail -n30
sudo fdisk -l

[playerx8]

Zasuň USB, chvíli počkej, a pak sem dej výpisy z

Kód: [Vybrat]

lsusb
dmesg | tail -n30
sudo fdisk -l

hmm.. a ako to dosiahnem, som s ubuntu novy..

[arrange]

Zadáš ty příkazy postupně do Terminálu. Pro práci v něm ho budeš muset otevřít a kopírovat do/z něj, pokud nevíš, jak na to, mrkni sem: http://wiki.ubuntu.cz/Termin%C3%A1l, hlavně část Spuštění a Kopírování textu.

[playerx8]

matus@matus-laptop:~$ lsusb
Bus 005 Device 005: ID 0930:6545 Toshiba Corp.
Bus 005 Device 002: ID 04f2:b008 Chicony Electronics Co., Ltd
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
matus@matus-laptop:~$ dmesg | tail -n30
[ 2483.696730] wlan0: authenticate with AP 00:1e:58:0e:2f:c0
[ 2483.696769] wlan0: RX authentication from 00:1e:58:0e:2f:c0 (alg=0 transaction=2 status=0)
[ 2483.696775] wlan0: authenticated
[ 2483.696782] wlan0: associate with AP 00:1e:58:0e:2f:c0
[ 2483.698471] wlan0: authentication frame received from 00:1e:58:0e:2f:c0, but not in authenticate state - ignored
[ 2483.700745] wlan0: RX ReassocResp from 00:1e:58:0e:2f:c0 (capab=0x431 status=0 aid=1)
[ 2483.700756] wlan0: associated
[ 2919.896195] wlan0: RX disassociation from 00:1e:58:0e:2f:c0 (reason=4)
[ 2919.896207] wlan0: disassociated
[ 2920.892929] wlan0: associate with AP 00:1e:58:0e:2f:c0
[ 2920.895296] wlan0: RX ReassocResp from 00:1e:58:0e:2f:c0 (capab=0x431 status=17 aid=1)
[ 2920.895309] wlan0: AP denied association (code=17)
[ 2921.092828] wlan0: associate with AP 00:1e:58:0e:2f:c0
[ 2921.095150] wlan0: RX ReassocResp from 00:1e:58:0e:2f:c0 (capab=0x431 status=17 aid=1)
[ 2921.095158] wlan0: AP denied association (code=17)
[ 2921.292701] wlan0: associate with AP 00:1e:58:0e:2f:c0
[ 2921.295060] wlan0: RX ReassocResp from 00:1e:58:0e:2f:c0 (capab=0x431 status=17 aid=1)
[ 2921.295072] wlan0: AP denied association (code=17)
[ 2921.492562] wlan0: association with AP 00:1e:58:0e:2f:c0 timed out
[ 2923.005059] wlan0: Initial auth_alg=0
[ 2923.005073] wlan0: authenticate with AP 00:1e:58:0e:2f:c0
[ 2923.009356] wlan0: Initial auth_alg=0
[ 2923.009369] wlan0: authenticate with AP 00:1e:58:0e:2f:c0
[ 2923.009409] wlan0: RX authentication from 00:1e:58:0e:2f:c0 (alg=0 transaction=2 status=0)
[ 2923.009415] wlan0: authenticated
[ 2923.009421] wlan0: associate with AP 00:1e:58:0e:2f:c0
[ 2923.011095] wlan0: authentication frame received from 00:1e:58:0e:2f:c0, but not in authenticate state - ignored
[ 2923.013424] wlan0: RX ReassocResp from 00:1e:58:0e:2f:c0 (capab=0x431 status=0 aid=1)
[ 2923.013436] wlan0: associated
[ 3007.477231] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
matus@matus-laptop:~$ sudo fdisk -l

Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xe692b9eb

Device Boot Start End Blocks Id System
/dev/sda1 * 1 18704 150239848+ 83 Linux
/dev/sda2 18705 19457 6048472+ 5 Extended
/dev/sda5 18705 19457 6048441 82 Linux swap / Solaris

Disk /dev/sdb: 2031 MB, 2031091712 bytes
16 heads, 32 sectors/track, 7748 cylinders
Units = cylinders of 512 * 512 = 262144 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sdb1 * 16 7748 1979456 e W95 FAT16 (LBA)

[arrange]

V tom výpisu z dmesg nevidím ten klíč, přitom v fdisk je vidět jako sdb1. Dej ještě výpis z

Kód: [Vybrat]

dmesg | grep -i sdb

[playerx8]

[ 47.453335] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 47.454096] sd 2:0:0:0: [sdb] Write Protect is off
[ 47.454102] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 47.454108] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 47.456832] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 47.457593] sd 2:0:0:0: [sdb] Write Protect is off
[ 47.457598] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 47.457603] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 47.457610] sdb: sdb1
[ 47.459209] sd 2:0:0:0: [sdb] Attached SCSI removable disk

[arrange]

Ještě Tě to nepřestalo bavit? Tak jedeme dál: zasuň, pár sekund počkej, a dej tyto příkazy, zase jejich výsledky (hlavně těch posledních tří) zkopíruj sem

Kód: [Vybrat]

cd /media
sudo mkdir test
sudo mount -v /dev/sdb1 test/
dmesg | tail -n25
mount | grep sdb1
(=zkoušíme připojit ručně příkazem mount, uvidíme, co systém na to)

[playerx8]

matus@matus-laptop:~$ cd /media
matus@matus-laptop:/media$ sudo mkdir test
mkdir: nie je možné vytvoriť adresár `test': File exists
matus@matus-laptop:/media$ sudo mount -v /dev/sdb1 test/
mount: you didn't specify a filesystem type for /dev/sdb1
I will try all types mentioned in /etc/filesystems or /proc/filesystems
Trying fuseblk
mount: you must specify the filesystem type
matus@matus-laptop:/media$ sudo mount -v /dev/sdb1 test/
mount: you didn't specify a filesystem type for /dev/sdb1
I will try all types mentioned in /etc/filesystems or /proc/filesystems
Trying fuseblk
mount: you must specify the filesystem type
matus@matus-laptop:/media$ dmesg | tail -n25
[ 1860.715520] wlan0: associated
[ 1860.719610] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1876.655011] wlan0: no IPv6 routers present
[ 1951.201953] usb 5-1: new high speed USB device using ehci_hcd and address 3
[ 1951.336669] usb 5-1: configuration #1 chosen from 1 choice
[ 1951.879802] usbcore: registered new interface driver libusual
[ 1951.913862] Initializing USB Mass Storage driver...
[ 1951.914353] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1951.914783] usbcore: registered new interface driver usb-storage
[ 1951.914792] USB Mass Storage support registered.
[ 1951.915517] usb-storage: device found at 3
[ 1951.915524] usb-storage: waiting for device to settle before scanning
[ 1956.914473] usb-storage: device scan complete
[ 1956.915068] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 1957.633882] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 1957.634863] sd 2:0:0:0: [sdb] Write Protect is off
[ 1957.634872] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1957.634878] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1957.637984] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 1957.638626] sd 2:0:0:0: [sdb] Write Protect is off
[ 1957.638635] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1957.638640] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1957.638651] sdb: sdb1
[ 1957.686286] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 1957.686374] sd 2:0:0:0: Attached scsi generic sg2 type 0
matus@matus-laptop:/media$ dmesg | tail -n25
[ 1860.715520] wlan0: associated
[ 1860.719610] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1876.655011] wlan0: no IPv6 routers present
[ 1951.201953] usb 5-1: new high speed USB device using ehci_hcd and address 3
[ 1951.336669] usb 5-1: configuration #1 chosen from 1 choice
[ 1951.879802] usbcore: registered new interface driver libusual
[ 1951.913862] Initializing USB Mass Storage driver...
[ 1951.914353] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1951.914783] usbcore: registered new interface driver usb-storage
[ 1951.914792] USB Mass Storage support registered.
[ 1951.915517] usb-storage: device found at 3
[ 1951.915524] usb-storage: waiting for device to settle before scanning
[ 1956.914473] usb-storage: device scan complete
[ 1956.915068] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 1957.633882] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 1957.634863] sd 2:0:0:0: [sdb] Write Protect is off
[ 1957.634872] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1957.634878] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1957.637984] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 1957.638626] sd 2:0:0:0: [sdb] Write Protect is off
[ 1957.638635] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1957.638640] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1957.638651] sdb: sdb1
[ 1957.686286] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 1957.686374] sd 2:0:0:0: Attached scsi generic sg2 type 0
matus@matus-laptop:/media$ dmesg | tail -n25
[ 1860.715520] wlan0: associated
[ 1860.719610] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1876.655011] wlan0: no IPv6 routers present
[ 1951.201953] usb 5-1: new high speed USB device using ehci_hcd and address 3
[ 1951.336669] usb 5-1: configuration #1 chosen from 1 choice
[ 1951.879802] usbcore: registered new interface driver libusual
[ 1951.913862] Initializing USB Mass Storage driver...
[ 1951.914353] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1951.914783] usbcore: registered new interface driver usb-storage
[ 1951.914792] USB Mass Storage support registered.
[ 1951.915517] usb-storage: device found at 3
[ 1951.915524] usb-storage: waiting for device to settle before scanning
[ 1956.914473] usb-storage: device scan complete
[ 1956.915068] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 1957.633882] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 1957.634863] sd 2:0:0:0: [sdb] Write Protect is off
[ 1957.634872] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1957.634878] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1957.637984] sd 2:0:0:0: [sdb] 3966976 512-byte hardware sectors (2031 MB)
[ 1957.638626] sd 2:0:0:0: [sdb] Write Protect is off
[ 1957.638635] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 1957.638640] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1957.638651] sdb: sdb1
[ 1957.686286] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 1957.686374] sd 2:0:0:0: Attached scsi generic sg2 type 0
matus@matus-laptop:/media$

nie, ja sa rad ucim pomaly zacinam tie prikazy chapat... chcem sa to naucit, proste zide sa

[arrange]

Nerozpoznal automaticky typ, zkus tedy po připojení dát

Kód: [Vybrat]

sudo mount -v -t vfat /dev/sdb1 /media/test

[playerx8]

problem sa tym vobec nevyriesil, sice pridalo usb medium, no poprve sa neda odpojit, a po druhe ho nacitalo len prvy krat, druhy krat a dalsi rkat uz nie.. jednoducho ho stale mam na ploche aj ked uz nie je v booku..

[playerx8]

a este sa z neho neda citat.. teda ak su tam data, nacita len velkost media, nic viac...otvori ho .. no nic na nom nevidno,teda ako keby tam enboli ziadne subory

[arrange]

Co to píše po tom sudo mount -v -t vfat /dev/sdb1 /media/test?

Máš tam nějaká důležitá data? Když to takhle různě vytahuješ bez odpojení, asi bude nejlepší to znovu naformátovat , protože je divné, že systém nepozná automaticky souborový systém.   

Formátuj třeba přes Správce oddílů.