Dobry den,
uz dlhsie sa snazim najst nejaky fungujuci navod na nastavenie xorg.conf tak aby mi sli dve lcd.
mam externe lcd benq 2200hd (1920x1080) a lcd na notebooku (1280x800). Funguje bud jedno alebo druhe.
Pokial chcem pomocou managera nastavit vystup na dve lcd (nie mirror ale rozsirit si plochu a dalsi monitor)
tak mi vyskoci okienko ktore ma informuje o tom ze pocitac rozsiri vyrtualne rozlisenie aby teda mohli fungovat dva monitory vedla seba a rozsirila sa mi plocha. Nasledne restartnem Xka a spusti sa mi prostredie ale na zacuiatku vidim obrysy okien a panelov v bielej farbe a nasledne cely monitor nahodi bielu farbu. Myska sa meni napr ked prechadzam z ikon na plochu...cize system a prostredie funguje ale zobrazenie nefunguje spravne. Nasledne pouzijem recovery conzolu aby mi napravila corg.conf
takto vyzera moj corg.conf
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# Note that some configuration settings that could be done previously
# in this file, now are automatically configured by the server and settings
# here are ignored.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Device"
Identifier "Configured Video Device"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
EndSection
Na internete som nasiel kopec navodov, akurat ze kazdy mal v x.conf zadefinovanych az niekolko konkretnych udajov pre device, monitor, a screen a este kopec inych veci.
Takze po prve by som sa rad opytal ci je potrebne aby som mal jednotlive zariadenia podrobne zadefinovane alebo staci iba nieco dopisat aby mi vyrtualne rozsirenie monitorov fungovalo?
A po druhe ci to uz bude tak alebo onak s tym x.conf... pomoze mi niekto tak aby som to rozbehal?
Nejaka sanca ze je programik ktory by to urobil za mna?
ubuntu 9.04 64bit
Tu su niejake dalsie info ktore by vam mohli pomoct sa zorientovat:
Eel-WARNING **: "nautilus-metafile.c: metafiles" hash table still has 4 elements at quit time (keys above)
(nautilus:4418): Eel-WARNING **: "nautilus-directory.c: directories" hash table still has 4 elements at quit time
pawan@pawan-laptop:~$ xrandr -q
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 1920 x 1920
VGA connected 1920x1080+0+0 (normal left inverted right x axis y axis) 476mm x 268mm
1920x1080 60.0*+
1680x1050 60.0
1280x1024 75.0 60.0
1440x900 75.0 59.9
1280x960 60.0
1280x800 59.8
1152x864 75.0
1152x720 60.0
1024x768 75.0 60.0
832x624 74.6
800x600 75.0 60.3
640x480 75.0 59.9
720x400 70.1
LVDS connected (normal left inverted right x axis y axis)
1280x800 60.0 + 59.9
1024x768 75.0 70.1 60.0
832x624 74.6
800x600 85.1 72.2 75.0 60.3 56.2
640x480 85.0 72.8 75.0 59.9
720x400 85.0
640x400 85.1
640x350 85.1
a
pawan@pawan-laptop:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
02:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
03:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02)
03:0b.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
03:0b.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller
03:0b.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
03:0b.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
v tomto lspci vypise je to tak na nic napisane ale ja mam tuto grafiku:
výrobce : Intel®
typ : čipová sada 945GM Express
velikost paměti : až 128 MB
typ paměti : DDR2 RAM (UMA)
vykon: na nic
Diki
Téma: zobrazenie na dve lcd (Přečteno 1885 krát)
