Pomalý přístup na DVD na Asus A6 - 8.04

[oyankee]

Ahoj,
nikde jsem nic nenašel, tak snad tady někdo bude vědět.
Jakákoliv operace s DVD-RAMkou zapříčíní sekání systému. Myš se kouše, pak na vteřinu ok, ale pak znovu. Cpu na 75proc. Přenosová rychlost(i vypalovací) nejvíce na 700kB/s. Problém je na Hardym. Kernel 2.6.24-24

Kód: [Vybrat]

ondra@anetbook:~$ lspci -vv
00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a31 (rev 01)
Subsystem: ATI Technologies Inc Unknown device 5a31
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 3: Memory at <ignored> (64-bit, non-prefetchable)

00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fe100000-fe1fffff
Prefetchable memory behind bridge: bdf00000-ddefffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>

00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>

00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>

00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>

00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 0b00 [size=16]
Region 1: Memory at fed00000 (32-bit, non-prefetchable) [size=1K]

00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (rev 80) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: <access denied>

00:14.2 Audio device: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 1393
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 5
Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>

00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fe200000-feafffff
Prefetchable memory behind bridge: ddf00000-dfefffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200M] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Unknown device 1392
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 255 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 9800 [size=256]
Region 2: Memory at fe1f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fe1c0000 [disabled] [size=128K]
Capabilities: <access denied>

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: ASUSTeK Computer Inc. L8400B or L3C/S notebook
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at feaffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fe200000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 44000000-47fff000
I/O window 0: 0000a000-0000a0ff
I/O window 1: 0000a400-0000a4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001

02:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin C routed to IRQ 5
Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

02:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08)
Subsystem: ASUSTeK Computer Inc. Unknown device 1397
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: Memory at feaff400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. A6U notebook embedded card
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 5
Region 0: Memory at feafc000 (32-bit, non-prefetchable) [size=8K]
V dmesg jsem nasel toto:

Kód: [Vybrat]

sr 1:0:1:0: Attached scsi generic sg1 type 5
[   83.871429] sr0: scsi3-mmc drive: 31x/31x writer dvd-ram cd/rw xa/form2 cdda tray
[   83.871434] Uniform CD-ROM driver Revision: 3.20
[   83.871476] sr 1:0:1:0: Attached scsi CD-ROM sr0


[oyankee]

ještě:

Kód: [Vybrat]

wodim -checkdrive dev=/dev/sr0
Error trying to open /dev/sr0 exclusively (Device or resource busy)... retrying in 1 second.
Error trying to open /dev/sr0 exclusively (Device or resource busy)... retrying in 1 second.
Error trying to open /dev/sr0 exclusively (Device or resource busy)... retrying in 1 second.
Error trying to open /dev/sr0 exclusively (Device or resource busy)... retrying in 1 second.
Error trying to open /dev/sr0 exclusively (Device or resource busy)... giving up.
wodim: Device or resource busy.
Cannot open SCSI driver!
For possible targets try 'wodim --devices' or 'wodim -scanbus'.
For possible transport specifiers try 'wodim dev=help'.
For IDE/ATAPI devices configuration, see the file README.ATAPI.setup from
the wodim documentation.

[LivArt]

a u ostatních disků to nedělá?

[oyankee]

Ne, dělá u každého média.