Kaffeine nenajde zařízeni,tv karta

[Mraky]

Ahoj,nevím z jakého důvodu mi kaffeine přestal detekovat tv kartu(winfast DTV2000 H rev. J),ostatní přehráváče jdou(vlc,ME tv,xine).V minulosti se mi to už někdy stalo,že po restartu/zapnutí počítače nedetekoval,ale pak stačil další restart,a dobrý,ale tentokrát nic:_(( .Zde přikládám dmesg:

Kód: [Vybrat]

[    0.109694] pci 0000:00:1d.7: PME# disabled
[    0.109806] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.109816] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[    0.109822] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH4 GPIO
[    0.109857] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[    0.109868] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[    0.109877] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[    0.109886] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[    0.109896] pci 0000:00:1f.1: reg 20 io port: [0xfc00-0xfc0f]
[    0.109906] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
[    0.109947] pci 0000:00:1f.2: reg 10 io port: [0xd400-0xd407]
[    0.109957] pci 0000:00:1f.2: reg 14 io port: [0xd000-0xd003]
[    0.109966] pci 0000:00:1f.2: reg 18 io port: [0xcc00-0xcc07]
[    0.109975] pci 0000:00:1f.2: reg 1c io port: [0xc800-0xc803]
[    0.109984] pci 0000:00:1f.2: reg 20 io port: [0xc400-0xc40f]
[    0.110051] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[    0.110119] pci 0000:00:1f.5: reg 10 io port: [0xd800-0xd8ff]
[    0.110128] pci 0000:00:1f.5: reg 14 io port: [0xdc00-0xdc3f]
[    0.110138] pci 0000:00:1f.5: reg 18 32bit mmio: [0xf7fff800-0xf7fff9ff]
[    0.110147] pci 0000:00:1f.5: reg 1c 32bit mmio: [0xf7fff400-0xf7fff4ff]
[    0.110187] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
[    0.110194] pci 0000:00:1f.5: PME# disabled
[    0.110273] pci 0000:01:00.0: reg 10 32bit mmio: [0xe0000000-0xefffffff]
[    0.110284] pci 0000:01:00.0: reg 14 io port: [0xa800-0xa8ff]
[    0.110293] pci 0000:01:00.0: reg 18 32bit mmio: [0xf1df0000-0xf1dfffff]
[    0.110320] pci 0000:01:00.0: reg 30 32bit mmio: [0xf1dc0000-0xf1ddffff]
[    0.110359] pci 0000:01:00.0: supports D1 D2
[    0.110416] pci 0000:00:01.0: bridge io port: [0xa000-0xafff]
[    0.110422] pci 0000:00:01.0: bridge 32bit mmio: [0xf1d00000-0xf1dfffff]
[    0.110429] pci 0000:00:01.0: bridge 32bit mmio pref: [0xd1c00000-0xf1bfffff]
[    0.110464] pci 0000:02:01.0: reg 10 io port: [0xbc00-0xbc1f]
[    0.110550] pci 0000:02:02.0: reg 10 32bit mmio: [0xf4000000-0xf4ffffff]
[    0.110649] pci 0000:02:02.1: reg 10 32bit mmio: [0xf5000000-0xf5ffffff]
[    0.110740] pci 0000:02:02.2: reg 10 32bit mmio: [0xf6000000-0xf6ffffff]
[    0.110843] pci 0000:02:05.0: reg 10 io port: [0xb800-0xb8ff]
[    0.110853] pci 0000:02:05.0: reg 14 32bit mmio: [0xf7effc00-0xf7effcff]
[    0.110903] pci 0000:02:05.0: supports D1 D2
[    0.110907] pci 0000:02:05.0: PME# supported from D1 D2 D3hot D3cold
[    0.110914] pci 0000:02:05.0: PME# disabled
[    0.110961] pci 0000:00:1e.0: transparent bridge
[    0.110968] pci 0000:00:1e.0: bridge io port: [0xb000-0xbfff]
[    0.110975] pci 0000:00:1e.0: bridge 32bit mmio: [0xf1e00000-0xf7efffff]
[    0.110996] pci_bus 0000:00: on NUMA node 0
[    0.111012] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.111188] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.114822] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.115044] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.115266] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.115481] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.115688] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.115898] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.116162] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.116373] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.116784] SCSI subsystem initialized
[    0.116964] libata version 3.00 loaded.
[    0.117205] usbcore: registered new interface driver usbfs
[    0.117235] usbcore: registered new interface driver hub
[    0.117335] usbcore: registered new device driver usb
[    0.117747] ACPI: WMI: Mapper loaded
[    0.117753] PCI: Using ACPI for IRQ routing
[    0.118058] Bluetooth: Core ver 2.15
[    0.118188] NET: Registered protocol family 31
[    0.118193] Bluetooth: HCI device and connection manager initialized
[    0.118198] Bluetooth: HCI socket layer initialized
[    0.118201] NetLabel: Initializing
[    0.118204] NetLabel:  domain hash size = 128
[    0.118207] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.118232] NetLabel:  unlabeled traffic allowed by default
[    0.118427] hpet clockevent registered
[    0.118434] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.118442] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.118450] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.126964] pnp: PnP ACPI init
[    0.127002] ACPI: bus type pnp registered
[    0.136173] pnp: PnP ACPI: found 14 devices
[    0.136181] ACPI: ACPI bus type pnp unregistered
[    0.136189] PnPBIOS: Disabled by ACPI PNP
[    0.136223] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[    0.136230] system 00:07: ioport range 0x800-0x87f has been reserved
[    0.136236] system 00:07: ioport range 0x480-0x4bf has been reserved
[    0.136243] system 00:07: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.136249] system 00:07: iomem range 0xff380000-0xffefffff has been reserved
[    0.136263] system 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.136270] system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.136285] system 00:0c: ioport range 0x680-0x6ff has been reserved
[    0.136291] system 00:0c: ioport range 0x295-0x296 has been reserved
[    0.136305] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[    0.136310] system 00:0d: iomem range 0xc0000-0xdffff could not be reserved
[    0.136315] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[    0.136319] system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
[    0.136324] system 00:0d: iomem range 0xfff00000-0xffffffff has been reserved
[    0.171154] AppArmor: AppArmor Filesystem Enabled
[    0.171221] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.171228] pci 0000:00:01.0:   IO window: 0xa000-0xafff
[    0.171236] pci 0000:00:01.0:   MEM window: 0xf1d00000-0xf1dfffff
[    0.171243] pci 0000:00:01.0:   PREFETCH window: 0xd1c00000-0xf1bfffff
[    0.171251] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[    0.171257] pci 0000:00:1e.0:   IO window: 0xb000-0xbfff
[    0.171264] pci 0000:00:1e.0:   MEM window: 0xf1e00000-0xf7efffff
[    0.171270] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.171295] pci 0000:00:1e.0: setting latency timer to 64
[    0.171304] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.171309] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.171313] pci_bus 0000:01: resource 0 io:  [0xa000-0xafff]
[    0.171317] pci_bus 0000:01: resource 1 mem: [0xf1d00000-0xf1dfffff]
[    0.171322] pci_bus 0000:01: resource 2 pref mem [0xd1c00000-0xf1bfffff]
[    0.171326] pci_bus 0000:02: resource 0 io:  [0xb000-0xbfff]
[    0.171330] pci_bus 0000:02: resource 1 mem: [0xf1e00000-0xf7efffff]
[    0.171334] pci_bus 0000:02: resource 3 io:  [0x00-0xffff]
[    0.171338] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[    0.171405] NET: Registered protocol family 2
[    0.171591] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.172261] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.173522] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.174160] TCP: Hash tables configured (established 131072 bind 65536)
[    0.174165] TCP reno registered
[    0.174396] NET: Registered protocol family 1
[    0.174519] Trying to unpack rootfs image as initramfs...
[    0.562973] Freeing initrd memory: 7725k freed
[    0.573547] cpufreq-nforce2: No nForce2 chipset.
[    0.573609] Scanning for low memory corruption every 60 seconds
[    0.573815] audit: initializing netlink socket (disabled)
[    0.573843] type=2000 audit(1266618686.571:1): initialized
[    0.586045] highmem bounce pool size: 64 pages
[    0.586059] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.588477] VFS: Disk quotas dquot_6.5.2
[    0.588617] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.589853] fuse init (API version 7.12)
[    0.590089] msgmni has been set to 1705
[    0.590712] alg: No test for stdrng (krng)
[    0.590765] io scheduler noop registered
[    0.590770] io scheduler anticipatory registered
[    0.590774] io scheduler deadline registered
[    0.590906] io scheduler cfq registered (default)
[    0.591036] pci 0000:01:00.0: Boot video device
[    0.591243] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.591305] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.591550] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.591559] ACPI: Power Button [PWRF]
[    0.591675] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.591683] ACPI: Power Button [PWRB]
[    0.592427] processor LNXCPU:00: registered as cooling_device0
[    0.592438] ACPI: Processor [CPU0] (supports 8 throttling states)
[    0.596766] isapnp: Scanning for PnP cards...
[    0.620001] Switched to high resolution mode on CPU 0
[    0.950906] isapnp: No Plug & Play device found
[    0.953623] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.953792] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.954527] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.956775] brd: module loaded
[    0.957834] loop: module loaded
[    0.958057] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    0.958295] ata_piix 0000:00:1f.1: version 2.13
[    0.958324]   alloc irq_desc for 18 on node -1
[    0.958329]   alloc kstat_irqs on node -1
[    0.958342] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.958424] ata_piix 0000:00:1f.1: setting latency timer to 64
[    0.958605] scsi0 : ata_piix
[    0.958846] scsi1 : ata_piix
[    0.961542] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[    0.961550] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[    0.962000] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.962011] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[    0.962086] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.962239] scsi2 : ata_piix
[    0.962422] scsi3 : ata_piix
[    0.962517] ata3: SATA max UDMA/133 cmd 0xd400 ctl 0xd000 bmdma 0xc400 irq 18
[    0.962523] ata4: SATA max UDMA/133 cmd 0xcc00 ctl 0xc800 bmdma 0xc408 irq 18
[    0.964638] Fixed MDIO Bus: probed
[    0.964715] PPP generic driver version 2.4.2
[    0.964991] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.965066]   alloc irq_desc for 23 on node -1
[    0.965071]   alloc kstat_irqs on node -1
[    0.965084] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[    0.965114] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.965121] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.965229] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.969156] ehci_hcd 0000:00:1d.7: debug port 1
[    0.969168] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[    0.969332] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7fffc00
[    0.984028] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.984212] usb usb1: configuration #1 chosen from 1 choice
[    0.984284] hub 1-0:1.0: USB hub found
[    0.984306] hub 1-0:1.0: 8 ports detected
[    0.984443] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.984493] uhci_hcd: USB Universal Host Controller Interface driver
[    0.984587]   alloc irq_desc for 16 on node -1
[    0.984592]   alloc kstat_irqs on node -1
[    0.984604] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.984620] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.984626] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.984745] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.984800] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e000
[    0.984991] usb usb2: configuration #1 chosen from 1 choice
[    0.985064] hub 2-0:1.0: USB hub found
[    0.985085] hub 2-0:1.0: 2 ports detected
[    0.985183]   alloc irq_desc for 19 on node -1
[    0.985188]   alloc kstat_irqs on node -1
[    0.985200] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.985218] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.985224] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.985333] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.985387] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400
[    0.985588] usb usb3: configuration #1 chosen from 1 choice
[    0.985660] hub 3-0:1.0: USB hub found
[    0.985679] hub 3-0:1.0: 2 ports detected
[    0.985783] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.985801] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.985807] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.985917] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.985957] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
[    0.986141] usb usb4: configuration #1 chosen from 1 choice
[    0.986216] hub 4-0:1.0: USB hub found
[    0.986236] hub 4-0:1.0: 2 ports detected
[    0.986338] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.986357] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.986363] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.986465] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.986507] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ec00
[    0.986694] usb usb5: configuration #1 chosen from 1 choice
[    0.986767] hub 5-0:1.0: USB hub found
[    0.986788] hub 5-0:1.0: 2 ports detected
[    0.987004] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.989775] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.989792] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.989986] mice: PS/2 mouse device common for all mice
[    0.990206] rtc_cmos 00:02: RTC can wake from S4
[    0.990311] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    0.990352] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[    0.990612] device-mapper: uevent: version 1.0.3
[    0.990900] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.991178] device-mapper: multipath: version 1.1.0 loaded
[    0.991186] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.991569] EISA: Probing bus 0 at eisa.0
[    0.991615] EISA: Detected 0 cards.
[    0.991796] cpuidle: using governor ladder
[    0.991801] cpuidle: using governor menu
[    0.992837] TCP cubic registered
[    0.993154] NET: Registered protocol family 10
[    0.994091] lo: Disabled Privacy Extensions
[    0.994617] NET: Registered protocol family 17
[    0.994680] Bluetooth: L2CAP ver 2.13
[    0.994685] Bluetooth: L2CAP socket layer initialized
[    0.994690] Bluetooth: SCO (Voice Link) ver 0.6
[    0.994692] Bluetooth: SCO socket layer initialized
[    0.994811] Bluetooth: RFCOMM TTY layer initialized
[    0.994819] Bluetooth: RFCOMM socket layer initialized
[    0.994822] Bluetooth: RFCOMM ver 1.11
[    0.994892] Using IPI No-Shortcut mode
[    0.995113] PM: Resume from disk failed.
[    0.995160] registered taskstats version 1
[    0.995399]   Magic number: 14:215:553
[    0.995476] pci_link PNP0C0F:04: hash matches
[    0.995528] rtc_cmos 00:02: setting system clock to 2010-02-19 22:31:28 UTC (1266618688)
[    0.995534] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.995537] EDD information not available.
[    1.019724] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    1.135999] ata2.00: ATAPI: TEAC DV-W516GA, C4S2, max UDMA/33
[    1.136291] ata3.00: ATA-8: ST3500320AS, SD15, max UDMA/133
[    1.136298] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.136412] ata1.01: ATA-6: WDC WD2000JB-00KFA0, 08.05J08, max UDMA/100
[    1.136417] ata1.01: 390721968 sectors, multi 16: LBA48
[    1.152805] ata2.00: configured for UDMA/33
[    1.152940] ata1.01: configured for UDMA/100
[    1.153251] scsi 0:0:1:0: Direct-Access     ATA      WDC WD2000JB-00K 08.0 PQ: 0 ANSI: 5
[    1.153547] sd 0:0:1:0: Attached scsi generic sg0 type 0
[    1.153706] sd 0:0:1:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
[    1.153908] sd 0:0:1:0: [sda] Write Protect is off
[    1.153915] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[    1.154023] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.154543]  sda:
[    1.154751] ata3.00: configured for UDMA/133
[    1.155770] scsi 1:0:0:0: CD-ROM            TEAC     DV-W516GA        C4S2 PQ: 0 ANSI: 5
[    1.160153] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[    1.160161] Uniform CD-ROM driver Revision: 3.20
[    1.160356] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.160491] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.160789] scsi 2:0:0:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
[    1.161087] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    1.161255] sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.161488] sd 2:0:0:0: [sdb] Write Protect is off
[    1.161495] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.161615] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.162182]  sdb: sda1 sda2 sda3 < sda5 >
[    1.169873] sd 0:0:1:0: [sda] Attached SCSI disk
[    1.172972]  sdb1 sdb2 < sdb5 >
[    1.186374] sd 2:0:0:0: [sdb] Attached SCSI disk
[    1.186413] Freeing unused kernel memory: 540k freed
[    1.187182] Write protecting the kernel text: 4580k
[    1.187228] Write protecting the kernel read-only data: 1840k
[    1.578133] Floppy drive(s): fd0 is 1.44M
[    1.663134] FDC 0 is a post-1991 82077
[    1.686731] Linux agpgart interface v0.103
[    1.713609] agpgart-intel 0000:00:00.0: Intel 865 Chipset
[    1.718074] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[    1.725093] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
[    1.725165]   alloc irq_desc for 22 on node -1
[    1.725170]   alloc kstat_irqs on node -1
[    1.725183] ne2k-pci 0000:02:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.726332] eth0: RealTek RTL-8029 found at 0xbc00, IRQ 22, 00:40:33:a0:e7:80.
[    1.800833] <6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    1.800893] 8139cp 0000:02:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[    1.806328] 8139too Fast Ethernet driver 0.9.28
[    1.806418] 8139too 0000:02:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.807996] eth1: RealTek RTL8139 at 0xb800, 00:19:66:73:74:51, IRQ 22
[    3.120195] xor: automatically using best checksumming function: pIII_sse
[    3.140017]    pIII_sse  :  2538.000 MB/sec
[    3.140023] xor: using function: pIII_sse (2538.000 MB/sec)
[    3.173464] device-mapper: dm-raid45: initialized v0.2594b
[    3.708509] PM: Starting manual resume from disk
[    3.708518] PM: Resume from partition 8:5
[    3.708522] PM: Checking hibernation image.
[    3.708833] PM: Resume from disk failed.
[    3.737471] EXT4-fs (sda1): barriers enabled
[    3.745127] kjournald2 starting: pid 337, dev sda1:8, commit interval 5 seconds
[    3.745245] EXT4-fs (sda1): delayed allocation enabled
[    3.745254] EXT4-fs: file extents enabled
[    3.745656] EXT4-fs: mballoc enabled
[    3.745695] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    4.403393] type=1505 audit(1266618691.904:2): operation="profile_load" pid=361 name=/usr/share/gdm/guest-session/Xsession
[    4.409082] type=1505 audit(1266618691.912:3): operation="profile_load" pid=362 name=/sbin/dhclient3
[    4.409968] type=1505 audit(1266618691.912:4): operation="profile_load" pid=362 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[    4.410458] type=1505 audit(1266618691.912:5): operation="profile_load" pid=362 name=/usr/lib/connman/scripts/dhclient-script
[    4.446250] type=1505 audit(1266618691.948:6): operation="profile_load" pid=363 name=/usr/bin/evince
[    4.460265] type=1505 audit(1266618691.964:7): operation="profile_load" pid=363 name=/usr/bin/evince-previewer
[    4.468516] type=1505 audit(1266618691.972:8): operation="profile_load" pid=363 name=/usr/bin/evince-thumbnailer
[    4.497846] type=1505 audit(1266618692.000:9): operation="profile_load" pid=365 name=/usr/lib/cups/backend/cups-pdf
[    4.498941] type=1505 audit(1266618692.000:10): operation="profile_load" pid=365 name=/usr/sbin/cupsd
[   17.631676] Adding 2899692k swap on /dev/sda5.  Priority:-1 extents:1 across:2899692k
[   17.705403] udev: starting version 147
[   17.791020] EXT4-fs (sda1): internal journal on sda1:8
[   17.949892] parport_pc 00:06: reported by Plug and Play ACPI
[   17.950012] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   18.001283] lp: driver loaded but no devices found
[   18.037225] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   18.096429] lp0: using parport0 (interrupt-driven).
[   18.580282] intel_rng: FWH not detected
[   18.729906] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   18.729915] Disabling lock debugging due to kernel taint
[   18.972247] ppdev: user-space parallel port driver
[   18.997793] [fglrx] Maximum main memory to use for locked dma buffers: 1885 MBytes.
[   18.997923] [fglrx]   vendor: 1002 device: 9587 count: 1
[   18.998279] [fglrx] ioport: bar 1, base 0xa800, size: 0x100
[   18.998309] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   18.998608] [fglrx] Kernel PAT support is enabled
[   18.998653] [fglrx] module loaded - fglrx 8.66.10 [Sep  3 2009] with 1 minors
[   19.296257] Linux video capture interface: v2.00
[   19.322726] psmouse serio1: ID: 10 00 64
[   19.512265] cx88/0: cx2388x v4l2 driver version 0.0.7 loaded
[   19.512350] cx8800 0000:02:02.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   19.512811] cx88[0]: subsystem: 107d:6f2b, board: WinFast DTV2000 H rev. J [card=82,autodetected], frontend(s): 1
[   19.512817] cx88[0]: TV tuner type 63, Radio tuner type -1
[   19.719535] cx2388x alsa driver version 0.0.7 loaded
[   19.744737] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.7 loaded
[   19.861277] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.028616] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[   20.340712] RPC: Registered udp transport module.
[   20.340719] RPC: Registered tcp transport module.
[   20.381628] eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
[   20.608997] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   20.609455] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[   20.609462] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[   20.609465] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[   20.630802] __ratelimit: 3 callbacks suppressed
[   20.630809] type=1505 audit(1266615108.132:12): operation="profile_replace" pid=892 name=/usr/share/gdm/guest-session/Xsession
[   20.635435] type=1505 audit(1266615108.136:13): operation="profile_replace" pid=893 name=/sbin/dhclient3
[   20.725387] type=1505 audit(1266615108.228:14): operation="profile_replace" pid=893 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   20.725910] type=1505 audit(1266615108.228:15): operation="profile_replace" pid=893 name=/usr/lib/connman/scripts/dhclient-script
[   20.772292] type=1505 audit(1266615108.276:16): operation="profile_replace" pid=905 name=/usr/bin/evince
[   20.874511] type=1505 audit(1266615108.376:17): operation="profile_replace" pid=905 name=/usr/bin/evince-previewer
[   20.953350] type=1505 audit(1266615108.456:18): operation="profile_replace" pid=905 name=/usr/bin/evince-thumbnailer
[   20.982037] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   21.017350] tuner 0-0043: chip found @ 0x86 (cx88[0])
[   21.050997] type=1505 audit(1266615108.552:19): operation="profile_replace" pid=933 name=/usr/lib/cups/backend/cups-pdf
[   21.110194] type=1505 audit(1266615108.612:20): operation="profile_replace" pid=933 name=/usr/sbin/cupsd
[   21.115620] type=1505 audit(1266615108.616:21): operation="profile_replace" pid=938 name=/usr/sbin/tcpdump
[   21.570755] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   21.664810]   alloc irq_desc for 17 on node -1
[   21.664817]   alloc kstat_irqs on node -1
[   21.664830] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   21.664931] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   21.666230] tda9887 0-0043: creating new instance
[   21.666238] tda9887 0-0043: tda988[5/6/7] found
[   21.686107] tuner 0-0061: chip found @ 0xc2 (cx88[0])
[   21.739650] NET: Registered protocol family 15
[   21.759151] alg: No test for cipher_null (cipher_null-generic)
[   21.759263] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[   21.759365] alg: No test for digest_null (digest_null-generic)
[   21.759465] alg: No test for compress_null (compress_null-generic)
[   21.856352] padlock: VIA PadLock Hash Engine not detected.
[   21.869511] tuner-simple 0-0061: creating new instance
[   21.869520] tuner-simple 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
[   21.873786] input: cx88 IR (WinFast DTV2000 H rev. as /devices/pci0000:00/0000:00:1e.0/0000:02:02.0/input/input5
[   21.873905] cx88[0]/0: found at 0000:02:02.0, rev: 5, irq: 23, latency: 32, mmio: 0xf4000000
[   21.873929] IRQ 23/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
[   21.874057] cx88[0]/0: registered device video0 [v4l2]
[   21.874151] cx88[0]/0: registered device vbi0
[   21.874239] cx88[0]/0: registered device radio0
[   21.900116] cx88_audio 0000:02:02.1: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   21.900133] IRQ 23/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
[   21.900172] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
[   21.901012] cx88[0]/2: cx2388x 8802 Driver Manager
[   21.901038] cx88-mpeg driver manager 0000:02:02.2: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   21.901051] cx88[0]/2: found at 0000:02:02.2, rev: 5, irq: 23, latency: 32, mmio: 0xf6000000
[   21.901064] IRQ 23/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
[   22.040090] intel8x0_measure_ac97_clock: measured 54963 usecs (2648 samples)
[   22.040097] intel8x0: clocking to 48000
[   22.043538] cx88/2: cx2388x dvb driver version 0.0.7 loaded
[   22.043545] cx88/2: registering cx8802 driver, type: dvb access: shared
[   22.043552] cx88[0]/2: subsystem: 107d:6f2b, board: WinFast DTV2000 H rev. J [card=82]
[   22.043557] cx88[0]/2: cx2388x based DVB/ATSC card
[   22.043561] cx8802_alloc_frontends() allocating 1 frontend(s)
[   22.050141] padlock: VIA PadLock Hash Engine not detected.
[   22.115287] tuner-simple 0-0061: attaching existing instance
[   22.115298] tuner-simple 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
[   22.161845] DVB: registering new adapter (cx88[0])
[   22.161856] DVB: registering adapter 0 frontend 0 (Conexant CX22702 DVB-T)...
[   22.223780] padlock: VIA PadLock not detected.
[   23.679115] intel_rng: FWH not detected
[   23.871668] Initializing XFRM netlink socket
[   23.885796] padlock: VIA PadLock not detected.
[   23.895955] padlock: VIA PadLock Hash Engine not detected.
[   23.913116] padlock: VIA PadLock not detected.
[   27.605265] [fglrx] AGP detected, AgpState   = 0x1f004a1b (hardware caps of chipset)
[   27.605277] [fglrx] [agp] enabling AGP with mode=0x1f004b1a
[   27.605286] agpgart-intel 0000:00:00.0: AGP 3.0 bridge
[   27.605314] agpgart-intel 0000:00:00.0: putting AGP V3 device into 8x mode
[   27.605366] fglrx_pci 0000:01:00.0: putting AGP V3 device into 8x mode
[   27.605409] [fglrx] AGP enabled,  AgpCommand = 0x1f004312 (selected caps)
[   27.687907] [fglrx] Setup AGP aperture
[   27.988283] [fglrx] Could not enable MSI; System prevented initialization
[   27.989468] [fglrx] Firegl kernel thread PID: 2024
[   28.832147] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   28.832156] vboxdrv: Successfully done.
[   28.832159] vboxdrv: Found 1 processor cores.
[   28.832408] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   28.832414] vboxdrv: Successfully loaded version 3.0.8_OSE (interface 0x000e0000).
[   30.968017] eth0: no IPv6 routers present
[   31.020017] eth1: no IPv6 routers present
[   32.002642] [fglrx] Gart cacheable size:875 M.
[   32.002659] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[   32.002663] [fglrx] Reserved FB block: Unshared offset:fe04000, size:1f8000
[   32.002668] [fglrx] Reserved FB block: Unshared offset:fffc000, size:4000
[   82.761911] process `skype.real' is using obsolete setsockopt SO_BSDCOMPAT


[ladarozan]

Která verze Kaffeina? Jaká verze Ubuntu a jádra? Je třeba pozorovat, co má vliv atd.
Pokud je to pravidelně to vynechávání, je třeba kartu posadit do jiného slotu PCI a raději spodního.
A ještě dodám, že poslední verze, co si říká 1, je poněkud oškubaná a neinstaluje ssebou vše potřebné.

[Mraky]

verze kaffeine je 1.0-pre2, a ubuntu je carmic koala,2.6.31-20-generic,ještě dodám že předtím než to šlo,sem přidávál nějaký zdroje, tak jestli to nebude tím... ale tak zkusím to dát do jinýho slotu.-)))doufám že pujde, nevím z hlavy jak to tam vypadá-)))

[macu]

ponechal sis starý jádro 2.6.31-19? pokud jo zkus to jestli ti to s ním pojede, jelikož tvá verze jádra ještě nebyla vydána, jedná se pouze o "testovací opravnou" verzi zatím...

[Mraky]

to macu: starší verze jádra jak víš většinou zůstáváj v záváděči, ty sem taky zkoušel a nic:_((( jinak ta karta byla bohužel v nejspodnějším slotu,přesto sem ale vyzkoušel ostatní sloty a nic:_((momentálně se nachází v nejvrchnějším slotu.(3pci sloty).Myslíte že kdybych downgradoval Kaffeine, že by to pomohlo?je nějaký obvyklý postup, krom toho že bych si sehnal starší verzi .deb balíčku kdesi na netu a instaloval?

[ladarozan]

Kaffeine je vázané s verzí Ubuntu. Takže pro ještě pěknou verzi 0.8.7 se musí jít na 9.04 Ubu.
Současné verze 1.0pre2 a 1.0pre3 neinstalují několik knihoven a musí se to doladit. Já to odbývám instalací Xine po instalaci Kaffeina.
Pak je to OK.
Vidím, že PCI nemělo vliv, takže karta je OK. Je to čistě věc knihoven pod Ubu.

[Mraky]

jojo, xine, ten sem kvůli správné funkci Kaffeine musel taky nainstalovat...

[macu]

ladarozan: trošku odbočím, vidím, že píšeš o verzi 1.0pre3, nikde jsem však nenašel deb balíček pro Ubuntu 9.10 (nejlíp 64bit), nevíš o něčem?

[giftman]

Mam take stejny problem, tedy v tom, ze mi ladeni najde vetsinu TV kanalu u Kaffeine a v predesle verzi Ubuntu 9.04 a v predchozich vse fungovalo ke vsi spokojenosti. Nyni jdou zde vsechny TV kanaly mimo CT1,2,24,4 a rozhlasove stanice nic. Nainstaloval jsem Me TV a zde je vse. :-(

[ladarozan]

Verzi 1.0pre3 jsem objevil při pokusné instalaci Ubu 10.04alpha2, ale jeví se mi stejně jako pre2.
Při laděním je nutné stisknout volbu pro stažení informací z netu. Pokud by se nenaladily všechny kanály,
je dobré nechat předvolbu ladění na AUTO a projet všechny TV kanály.

[Mraky]

Ahele! najednou mi kaffeine zase jde! ale taky jsem v synapticu zaškrtl, aby ubuntu bylo jako multimediální a tím pádem se mi nainstalovalo spousta audio/video programů,a navíc sem si koupil web cameru, takže navíc ještě cheese,a je možný ž se tím splnila nějaká závislost, díky které to kaffeine jede.-))) zatím ale po mě něchtějte vědět, o který program se konkrétně jedná,pokud je tomu skutečně tak, info dodám později,přecijenom těch prográmků se mi nainstalovalo asi 15-))

[ladarozan]

Výborně ! Tak jsme o kousek dál. Zřejmě jde o tu tzv. "svobodnou čistotu" systému, takže se musí
nastavit další zdroje.

[Mraky]

Tak zase změna,pro webkameru sem podle jednoho návodu nainstaloval xawtv a nějaký doplněk jménem webcam,poté to zase nešlo,ikdyž jsem tyto 2 sw pak odinstaloval.Napadla mě poslední věc,vrátil sem tv kartu z horního(ten nevyšší slot)slotu zpátky do nejspodnějšího,tedy do původního stavu,a už to zase funguje.jsem spíše BFU,takže pro mě je to docela divočina.-)))
Jinak, byl sem kvůli instalaci sw pro webkameru výjmečně ve windows(v době kdy sem tu tv kartu ještě měl v horním slotu)tak windows hlásili,že se objevil nový hardware,přesto že sw pro tv kartu již byl nainstalován,a nefungoval,hlasil nějakou chybu.Myslím si,že po přehození karty by to ve win již mohlo být v pořádku.
To ladarozan: co tím myslíš svobodnou čistotu?

[ladarozan]

Posun karty má stejný vliv u windows jako změna usb portu a ovladač se tomu musí přizpůsobit.
Tím "svobodným" mám na mysli vše, co nespadá čistě pod podmínky GPL viz wiki. Je tam pojednání
o omezených ovladačích atd.

[Mraky]

tak to zase nejde.-(( pokaždý, když na kompu něco udělám, tak to bud nejde nebo jde,jeto fakt divočina!napadlo mě smazat konfigurační soubor,ale ten sem nenašel i když vím kde by měl být(díval sem se do domovský složky),zkoušel sem  smazat složku .xine, ale to nepomohlo.Tentokrát sem vypojil disky, a zapojil úplně jinej a na něm instaloval win7, po zapojení původních disků to přestalo jít(ten úplně jinej disk sem odpojil)

[ladarozan]

Tak to je nějaké konfliktní. V Biosu by bylo potřeba přepnout z automatiky na pevné přiřazení IRQ. Pak to vše vyzkoušet znovu.

[Mraky]

irq? máš na mysli to připojování disků?nebo snad pevné přiřazení irq pro tu tv kartu? nejsem si jist,zda to v mém biosu pujde...

[Mraky]

hm,ráno to ještě nešlo,ted(asi ve3.PM)jsem zapnul kaffeine,zapomněl sem dodat,že se mi při spuštění kaffeine často spustí taky KDE control panel(audio),tam se nastavujou audio servery pro různá zařízení,tam sem něco nastavil(víceméně jentak ze srandy,aniž bych očekávál že to bude mít na sledování tv vliv)uložil změny,dal ok,a pak sem v kaffeine kliknul na tv,a ejhle,televize jde!Zdá se že zakopaný pes bude tady.Když by totiž znovu nastal nějaký problém,zase by se objevil ten panel,kde bych to musel znovu správně nastavit,pokud bych to nastavil špatně, bude se při každém dalším spuštění přehráváče spouštět taky ten panel,dokud bych to nenastavil správně,bo aspon si to myslím,že to tak je