nastavení síťové karty?

[c0rrupt]

Pustil jsem si mii-diag a vyskočilo mi toto

Kód: [Vybrat]

Basic registers of MII PHY #32:  1000 796d 001c c910 0de1 cde1 000f 2001.
 The autonegotiated capability is 01e0.
The autonegotiated media type is 100baseTx-FD.
 Basic mode control register 0x1000: Auto-negotiation enabled.
 You have link beat, and everything is working OK.
 Your link partner advertised cde1: Flow-control 100baseTx-FD 100baseTx 10baseT-FD 10baseT, w/ 802.3X flow control.
   End of basic transceiver information.

Mám ale gigovou síťovku v gigovém switchi, všechny Windowsové stanice mi jedou na gigem ale tohle vypadá, že to jede jenom 100kou. Včem je chyba? Dá se to nějak ručně nastavit?

Je to toto zařízení

Kód: [Vybrat]

       description: Ethernet interface
       product: Gigabit Network Adapter
       vendor: Linksys
       physical id: b
       bus info: pci@0000:00:0b.0
       logical name: eth1
       version: 10
       serial: 00:22:6b:be:64:b6
       size: 1GB/s
       capacity: 1GB/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.13 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=1GB/s
       resources: irq:16 ioport:e800(size=256) memory:fae00000-fae000ff memory:fad00000-fad1ffff(prefetchable)


[c0rrupt]

nikdo nic? hmmm

[TIBOR]

Neskusal si http://forum.ubuntu.cz/index.php/topic,5336.0.html
http://wiki.ubuntu.cz/Pomal%C3%BD%20upload

[c0rrupt]

no zkoušel nic, ktomu ethtool už bude asi zastaralý, právě jsem viděl všude rady používat mii-diag. Ten mi ale dává jako možnost max 100baseTx-FD.

[c0rrupt]

ethtool eth1

Kód: [Vybrat]

Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 1000Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000033 (51)
        Link detected: yes

hwinfo --netcard   jenom ta zapojená

Kód: [Vybrat]

16: PCI 0b.0: 0200 Ethernet controller
  [Created at pci.318]
  Unique ID: JNkJ.8XeFmf3NAED
  SysFS ID: /devices/pci0000:00/0000:00:0b.0
  SysFS BusID: 0000:00:0b.0
  Hardware Class: network
  Model: "Linksys EG1032 v3 Instant Gigabit Network Adapter"
  Vendor: pci 0x1737 "Linksys"
  Device: pci 0x1032 "Gigabit Network Adapter"
  SubVendor: pci 0x1737 "Linksys"
  SubDevice: pci 0x0024 "EG1032 v3 Instant Gigabit Network Adapter"
  Revision: 0x10
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth1
  I/O Ports: 0xe800-0xe8ff (rw)
  Memory Range: 0xfae00000-0xfae000ff (rw,non-prefetchable)
  Memory Range: 0xfad00000-0xfad1ffff (ro,prefetchable,disabled)
  IRQ: 16 (531682 events)
  HW Address: 00:22:6b:be:64:b6
  Link detected: yes
  Module Alias: "pci:v00001737d00001032sv00001737sd00000024bc02sc00i00"
  Driver Info #0:
    Driver Status: sk98lin is not active
    Driver Activation Cmd: "modprobe sk98lin"
  Driver Info #1:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=new, avail=yes, need=no, active=unknown


[c0rrupt]

Tohle teda hlásí asi, že jedu na gigu hmm? Ale proč mi to mii ukazuje blbě .