dvě síové karty

[locus]

zdravím mám dvě síťové karty integrované na základní desce. jedna je 100/10 a druha 1000/1000.

Jedna síťová karta jede nevím ted sice ktreá ale jede když dám příkaz ifconfig

tak se mi zobrazí toto:

Kód: [Vybrat]

root@locus:~# ifconfig
eth1      Link encap:Ethernet  HWaddr 00:11:2f:5f:31:43 
          inet addr:192.168.1.4  Bcast:255.255.255.255  Mask:255.255.255.0
          inet6 addr: fe80::211:2fff:fe5f:3143/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:489 errors:0 dropped:0 overruns:0 frame:0
          TX packets:122 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:61466 (60.0 KB)  TX bytes:16062 (15.6 KB)
          Interrupt:19

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
Nevíte jak pls zprovoznit tu druhou?

Děkuju moc za rady a tipy

[locus]

je to divné v tom jakoby výpisu jí vidím

Kód: [Vybrat]

root@tornado:~# lspci
00:00.0 Host bridge: nVidia Corporation nForce2 IGP2 (rev c1)
00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
[b]00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)[/b]
00:05.0 Multimedia audio controller: nVidia Corporation nForce Audio Processing Unit (rev a2)
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)
00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3)
00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire (IEEE 1394) Controller (rev a3)
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
[b]01:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)[/b]
01:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02)
03:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev a1)

nevíte prosim vás někdo jak na to pls

[locus]

ještě jsem zkoušel něco takového:

obě jsou zapojené

Kód: [Vybrat]

root@locus:~# ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 00:11:2f:5f:18:38 
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:16 Base address:0xa000

root@locus:~# ifconfig eth1
eth1      Link encap:Ethernet  HWaddr 00:11:2f:5f:31:43 
          inet addr:192.168.1.4  Bcast:255.255.255.255  Mask:255.255.255.0
          inet6 addr: fe80::211:2fff:fe5f:3143/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1457 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:197815 (193.1 KB)  TX bytes:1304053 (1.2 MB)
          Interrupt:19
nejak nechapu kde je chyba

[mosqa]

a aku siet alebo co potrebujes sprovoznit na tej druhej sietovke? system ju vidi, takze ju staci nastavit pre pouzitie v sieti o ktorej si sa nezmienil a vsetko by malo fungovat

[locus]

neměl jsme nakonfigurováno v /etc/network/interfaces

proto to jako by nejelo. protoze po restartu se jakoby neaktivovala.

Děkuju za reakce ted ještě řeším DMZ a přeměrování portů.

[locus]

ještě takový dotaz bokem půjčil jsme si takový ten USB LAN adapter

mám namysli to to http://www.penta.cz/redukce-adapter-usb-lan_d27356.html

nevíte náhodou někdo jak ho prosím vás zprovoznit??

když dám lsusb tak ho vidí jakože je v výpisu ale jak ten usb adapter uvést do funkčního stavu??
jak kde co nakonfigurovat nevíte prosím vás někdo?

[locus]

s tím že jsme ten adpater připojil na notebook s jednou integrovanoi síťovou kartou a s wifi

Kód: [Vybrat]

eth0      Link encap:Ethernet  HWadr 00:26:18:a2:3c:62 
          inet adr:192.168.1.3  Všesměr:192.168.1.255  Maska:255.255.255.0
          inet6-adr: fe80::226:18ff:fea2:3c62/64 Rozsah:Linka
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:269177 errors:0 dropped:0 overruns:0 frame:0
          TX packets:175354 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 396520412 (396.5 MB) Odesláno bajtů: 13354916 (13.3 MB)
          Přerušení:29 Vstupně/Výstupní port:0x2000

lo        Link encap:Místní smyčka 
          inet adr:127.0.0.1  Maska:255.0.0.0
          inet6-adr: ::1/128 Rozsah:Počítač
          AKTIVOVÁNO SMYČKA BĚŽÍ  MTU:16436  Metrika:1
          RX packets:2012 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2012 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 244229 (244.2 KB) Odesláno bajtů: 244229 (244.2 KB)

pan0      Link encap:Ethernet  HWadr c2:4b:f8:c0:84:4a 
          VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)

vboxnet0  Link encap:Ethernet  HWadr 0a:00:27:00:00:00 
          VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)

wlan0     Link encap:Ethernet  HWadr 00:1e:65:6b:02:6e 
          inet adr:192.168.0.5  Všesměr:192.168.0.255  Maska:255.255.255.0
          inet6-adr: fe80::21e:65ff:fe6b:26e/64 Rozsah:Linka
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:8995 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6895 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 7017589 (7.0 MB) Odesláno bajtů: 822214 (822.2 KB)

wmaster0  Link encap:NEZNÁM  HWadr 00-1E-65-6B-02-6E-36-62-00-00-00-00-00-00-00-00 
          AKTIVOVÁNO BĚŽÍ  MTU:0  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 0 (0.0 B) Odesláno bajtů: 0 (0.0 B)


[stderr]

když dám lsusb tak ho vidí jakože je v výpisu ale jak ten usb adapter uvést do funkčního stavu??
jak kde co nakonfigurovat nevíte prosím vás někdo?

po připojení si zkus vypsat hlášení kernelu (dmesg) - tam bude, pod jakým jménem se ti přihlásí do systému. Pak by to - teoreticky - mělo jít nakonfigurovat jako jiný síťový zařízení v interfaces...

[locus]

aha no vypis je takový co s tím můžu udělat dále prosim

Kód: [Vybrat]

[    1.141110] ata2: SATA max UDMA/133 abar m2048@0xfd8fb000 port 0xfd8fb180 irq 28
[    1.141113] ata3: DUMMY
[    1.141116] ata4: DUMMY
[    1.141120] ata5: SATA max UDMA/133 abar m2048@0xfd8fb000 port 0xfd8fb300 irq 28
[    1.141125] ata6: SATA max UDMA/133 abar m2048@0xfd8fb000 port 0xfd8fb380 irq 28
[    1.142623] Fixed MDIO Bus: probed
[    1.142677] PPP generic driver version 2.4.2
[    1.142805] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.142831] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.142849] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    1.142854] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    1.142899] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    1.146810] ehci_hcd 0000:00:1a.7: debug port 1
[    1.146820] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    1.146839] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfd8fbc00
[    1.161018] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    1.161127] usb usb1: configuration #1 chosen from 1 choice
[    1.161171] hub 1-0:1.0: USB hub found
[    1.161182] hub 1-0:1.0: 6 ports detected
[    1.161266]   alloc irq_desc for 23 on node -1
[    1.161270]   alloc kstat_irqs on node -1
[    1.161277] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.161291] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    1.161297] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.161344] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    1.165246] ehci_hcd 0000:00:1d.7: debug port 1
[    1.165255] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    1.165276] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfd8fb800
[    1.180024] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.180129] usb usb2: configuration #1 chosen from 1 choice
[    1.180171] hub 2-0:1.0: USB hub found
[    1.180181] hub 2-0:1.0: 6 ports detected
[    1.180269] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.180296] uhci_hcd: USB Universal Host Controller Interface driver
[    1.180327] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.180336] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    1.180341] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    1.180385] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    1.180427] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00005880
[    1.180541] usb usb3: configuration #1 chosen from 1 choice
[    1.180581] hub 3-0:1.0: USB hub found
[    1.180591] hub 3-0:1.0: 2 ports detected
[    1.180658]   alloc irq_desc for 21 on node -1
[    1.180661]   alloc kstat_irqs on node -1
[    1.180668] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    1.180677] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    1.180682] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    1.180726] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    1.180767] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00005800
[    1.180881] usb usb4: configuration #1 chosen from 1 choice
[    1.180925] hub 4-0:1.0: USB hub found
[    1.180934] hub 4-0:1.0: 2 ports detected
[    1.180998] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    1.181026] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    1.181031] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    1.181081] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    1.181123] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00005480
[    1.181238] usb usb5: configuration #1 chosen from 1 choice
[    1.181282] hub 5-0:1.0: USB hub found
[    1.181291] hub 5-0:1.0: 2 ports detected
[    1.181359] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.181368] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.181373] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.181416] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    1.181448] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00005400
[    1.181572] usb usb6: configuration #1 chosen from 1 choice
[    1.181613] hub 6-0:1.0: USB hub found
[    1.181623] hub 6-0:1.0: 2 ports detected
[    1.181686] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.181696] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.181701] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.181743] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    1.181774] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00005080
[    1.181889] usb usb7: configuration #1 chosen from 1 choice
[    1.181928] hub 7-0:1.0: USB hub found
[    1.181937] hub 7-0:1.0: 2 ports detected
[    1.181999] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.182008] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.182014] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.182056] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    1.182089] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005000
[    1.182205] usb usb8: configuration #1 chosen from 1 choice
[    1.182245] hub 8-0:1.0: USB hub found
[    1.182254] hub 8-0:1.0: 2 ports detected
[    1.182407] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    1.185295] i8042.c: Detected active multiplexing controller, rev 1.1.
[    1.186856] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.186864] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.186869] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.186874] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.186878] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.186959] mice: PS/2 mouse device common for all mice
[    1.187143] rtc_cmos 00:03: RTC can wake from S4
[    1.187191] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.187227] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.187386] device-mapper: uevent: version 1.0.3
[    1.187530] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    1.187651] device-mapper: multipath: version 1.1.0 loaded
[    1.187655] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.187831] EISA: Probing bus 0 at eisa.0
[    1.187855] Cannot allocate resource for EISA slot 4
[    1.187858] Cannot allocate resource for EISA slot 5
[    1.187862] Cannot allocate resource for EISA slot 6
[    1.187865] Cannot allocate resource for EISA slot 7
[    1.187869] Cannot allocate resource for EISA slot 8
[    1.187872] EISA: Detected 0 cards.
[    1.188118] cpuidle: using governor ladder
[    1.188309] cpuidle: using governor menu
[    1.189094] TCP cubic registered
[    1.189343] NET: Registered protocol family 10
[    1.190050] lo: Disabled Privacy Extensions
[    1.190583] NET: Registered protocol family 17
[    1.190608] Bluetooth: L2CAP ver 2.13
[    1.190611] Bluetooth: L2CAP socket layer initialized
[    1.190616] Bluetooth: SCO (Voice Link) ver 0.6
[    1.190618] Bluetooth: SCO socket layer initialized
[    1.190666] Bluetooth: RFCOMM TTY layer initialized
[    1.190670] Bluetooth: RFCOMM socket layer initialized
[    1.190673] Bluetooth: RFCOMM ver 1.11
[    1.191698] Using IPI No-Shortcut mode
[    1.191760] PM: Resume from disk failed.
[    1.191772] registered taskstats version 1
[    1.191883]   Magic number: 10:369:298
[    1.191983] rtc_cmos 00:03: setting system clock to 2010-05-19 21:17:15 UTC (1274303835)
[    1.191986] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.191987] EDD information not available.
[    1.225995] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    1.468119] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.469226] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[    1.469425] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
[    1.469430] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[    1.469941] ata1.00: ATA-8: FUJITSU MHZ2250BH G1, 0084000B, max UDMA/100
[    1.469946] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.471071] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[    1.471206] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
[    1.471212] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[    1.471777] ata1.00: configured for UDMA/100
[    1.484317] scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHZ2250B 0084 PQ: 0 ANSI: 5
[    1.484418] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.484463] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.484504] sd 0:0:0:0: [sda] Write Protect is off
[    1.484507] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.484528] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.484640]  sda:
[    1.500042] Clocksource tsc unstable (delta = -261812779 ns)
[    1.513378]  sda1 sda2 sda3 < sda5 sda6 >
[    1.549126] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.696126] usb 2-5: new high speed USB device using ehci_hcd and address 2
[    2.208061] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.212907] ata2.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
[    2.212913] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[    2.216827] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T50N, RE05, max UDMA/133
[    2.222934] ata2.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
[    2.222939] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[    2.226820] ata2.00: configured for UDMA/133
[    2.355257] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T50N  RE05 PQ: 0 ANSI: 5
[    2.387310] usb 2-5: configuration #1 chosen from 1 choice
[    2.660065] usb 5-1: new full speed USB device using uhci_hcd and address 2
[    2.681329] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.681334] Uniform CD-ROM driver Revision: 3.20
[    2.681456] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.681517] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.826269] usb 5-1: configuration #1 chosen from 1 choice
[    3.000161] ata5: SATA link down (SStatus 0 SControl 300)
[    3.068104] usb 5-2: new full speed USB device using uhci_hcd and address 3
[    3.188151] usb 5-2: device descriptor read/64, error -71
[    3.336114] ata6: SATA link down (SStatus 0 SControl 300)
[    3.352207] Freeing unused kernel memory: 544k freed
[    3.352560] Write protecting the kernel text: 4584k
[    3.352615] Write protecting the kernel read-only data: 1840k
[    3.413993] usb 5-2: device descriptor read/64, error -71
[    3.439881] ramzswap: disk size set to 506772 kB
[    3.517366] Linux agpgart interface v0.103
[    3.519978] agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset
[    3.520673] agpgart-intel 0000:00:00.0: detected 32764K stolen memory
[    3.524200] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    3.543681] ohci1394 0000:0d:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.547812] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.547851] r8169 0000:0c:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    3.547973] r8169 0000:0c:00.0: setting latency timer to 64
[    3.548169]   alloc irq_desc for 29 on node -1
[    3.548171]   alloc kstat_irqs on node -1
[    3.548223] r8169 0000:0c:00.0: irq 29 for MSI/MSI-X
[    3.548889] eth0: RTL8168c/8111c at 0xf81d2000, 00:26:18:a2:3c:62, XID 3c4000c0 IRQ 29
[    3.585435] Adding 506768k swap on /dev/ramzswap0.  Priority:100 extents:1 across:506768k SSD
[    3.589892] [drm] Initialized drm 1.1.0 20060810
[    3.602041] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]  MMIO=[febff800-febfffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    3.607732] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.607738] i915 0000:00:02.0: setting latency timer to 64
[    3.610154]   alloc irq_desc for 30 on node -1
[    3.610158]   alloc kstat_irqs on node -1
[    3.610167] i915 0000:00:02.0: irq 30 for MSI/MSI-X
[    3.629044] usb 5-2: new full speed USB device using uhci_hcd and address 4
[    3.717139] [drm] i2c_init DPDDC-B
[    3.726659] [drm] i2c_init DPDDC-D
[    3.749041] usb 5-2: device descriptor read/64, error -71
[    3.948052] i2c-adapter i2c-2: unable to read EDID block.
[    3.948056] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[    3.973041] usb 5-2: device descriptor read/64, error -71
[    4.189040] usb 5-2: new full speed USB device using uhci_hcd and address 5
[    4.236698] [drm] TV-21: set mode NTSC 480i 0
[    4.361650] [drm] fb0: inteldrmfb frame buffer device
[    4.361993] ACPI Warning: _BQC returned an invalid level 20090521 video-629
[    4.363488] acpi device:1e: registered as cooling_device2
[    4.363612] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1b/input/input5
[    4.363640] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    4.363677] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    4.429475] [drm] DAC-6: set mode 1024x768 c
[    4.489843] [drm] LVDS-8: set mode 1280x800 2c
[    4.597039] usb 5-2: device not accepting address 5, error -71
[    4.611732] Console: switching to colour frame buffer device 128x48
[    4.709046] usb 5-2: new full speed USB device using uhci_hcd and address 6
[    4.754752] xor: automatically using best checksumming function: pIII_sse
[    4.773008]    pIII_sse  :  8340.000 MB/sec
[    4.773010] xor: using function: pIII_sse (8340.000 MB/sec)
[    4.775290] device-mapper: dm-raid45: initialized v0.2594b
[    4.877206] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001e8c0001ff7895]
[    5.010791] PM: Starting manual resume from disk
[    5.010794] PM: Resume from partition 8:6
[    5.010796] PM: Checking hibernation image.
[    5.010989] PM: Resume from disk failed.
[    5.038264] EXT4-fs (sda5): barriers enabled
[    5.053107] kjournald2 starting: pid 490, dev sda5:8, commit interval 5 seconds
[    5.053261] EXT4-fs (sda5): delayed allocation enabled
[    5.053265] EXT4-fs: file extents enabled
[    5.058130] EXT4-fs: mballoc enabled
[    5.058144] EXT4-fs (sda5): mounted filesystem with ordered data mode
[    5.117052] usb 5-2: device not accepting address 6, error -71
[    5.117079] hub 5-0:1.0: unable to enumerate USB device on port 2
[    6.588990] Adding 4225052k swap on /dev/sda6.  Priority:-1 extents:1 across:4225052k
[    6.915985] EXT4-fs (sda5): warning: maximal mount count reached, running e2fsck is recommended
[    6.940488] EXT4-fs (sda5): internal journal on sda5:8
[    7.789952] udev: starting version 147
[    9.251664] lp: driver loaded but no devices found
[    9.254253] Bluetooth: Generic Bluetooth USB driver ver 0.5
[    9.254367] usbcore: registered new interface driver btusb
[    9.337712] Linux video capture interface: v2.00
[    9.444230] uvcvideo: Found UVC 1.00 device USB2.0 UVC PC Camera (17ef:480a)
[    9.513517] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.520099] cfg80211: Calling CRDA to update world regulatory domain
[    9.522493] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
[    9.545571] usbcore: registered new interface driver uvcvideo
[    9.545575] USB Video Class driver (v0.1.0)
[    9.550353] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    9.550571] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    9.550574] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    9.550576] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    9.973187] ricoh-mmc: Ricoh MMC Controller disabling driver
[    9.973192] ricoh-mmc: Copyright(c) Philip Langdale
[    9.973228] ricoh-mmc: Ricoh MMC controller found at 0000:0d:00.2 [1180:0843] (rev 12)
[    9.973248] ricoh-mmc: Controller is now disabled.
[    9.974838] sdhci: Secure Digital Host Controller Interface driver
[    9.974841] sdhci: Copyright(c) Pierre Ossman
[   10.024954] sdhci-pci 0000:0d:00.1: SDHCI controller found [1180:0822] (rev 22)
[   10.024976] sdhci-pci 0000:0d:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   10.026007] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[   10.027054] Registered led device: mmc0::
[   10.028090] mmc0: SDHCI controller on PCI [0000:0d:00.1] using DMA
[   10.130978] input: DualPoint Stick as /devices/platform/i8042/serio4/input/input6
[   10.162835] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio4/input/input7
[   10.232296] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27k
[   10.232299] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[   10.232379] iwlagn 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   10.232388] iwlagn 0000:02:00.0: setting latency timer to 64
[   10.232423] iwlagn 0000:02:00.0: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
[   10.281862] iwlagn 0000:02:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[   10.281929]   alloc irq_desc for 31 on node -1
[   10.281931]   alloc kstat_irqs on node -1
[   10.281951] iwlagn 0000:02:00.0: irq 31 for MSI/MSI-X
[   10.539991] cfg80211: World regulatory domain updated:
[   10.539995] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.539998] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.540014] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.540016] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.540019] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.540021] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.637627] phy0: Selected rate control algorithm 'iwl-agn-rs'
[   10.770245] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.235615]   alloc irq_desc for 22 on node -1
[   11.235619]   alloc kstat_irqs on node -1
[   11.235625] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   11.235670] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   11.527169] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   11.527242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   11.527299] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   11.527350] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   11.950450] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   11.950453] Bluetooth: BNEP filters: protocol multicast
[   12.099719] Bridge firewalling registered
[   15.356044] iwlagn 0000:02:00.0: firmware: requesting iwlwifi-5000-2.ucode
[   15.415071] type=1505 audit(1274296649.720:2): operation="profile_load" pid=1331 name=/usr/share/gdm/guest-session/Xsession
[   15.461442] type=1505 audit(1274296649.768:3): operation="profile_load" pid=1336 name=/sbin/dhclient3
[   15.462134] type=1505 audit(1274296649.768:4): operation="profile_load" pid=1336 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   15.462499] type=1505 audit(1274296649.768:5): operation="profile_load" pid=1336 name=/usr/lib/connman/scripts/dhclient-script
[   15.579071] iwlagn 0000:02:00.0: loaded firmware version 8.24.2.12
[   15.603832] type=1505 audit(1274296649.908:6): operation="profile_load" pid=1338 name=/usr/bin/evince
[   15.615588] type=1505 audit(1274296649.920:7): operation="profile_load" pid=1338 name=/usr/bin/evince-previewer
[   15.622195] type=1505 audit(1274296649.928:8): operation="profile_load" pid=1338 name=/usr/bin/evince-thumbnailer
[   15.680727] type=1505 audit(1274296649.985:9): operation="profile_load" pid=1341 name=/usr/lib/cups/backend/cups-pdf
[   15.681805] type=1505 audit(1274296649.989:10): operation="profile_load" pid=1341 name=/usr/sbin/cupsd
[   15.725495] Registered led device: iwl-phy0::radio
[   15.725528] Registered led device: iwl-phy0::assoc
[   15.725555] Registered led device: iwl-phy0::RX
[   15.725582] Registered led device: iwl-phy0::TX
[   15.741789] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   15.743202] r8169: eth0: link down
[   15.743393] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.749412] type=1505 audit(1274296650.057:11): operation="profile_load" pid=1344 name=/usr/sbin/mysqld
[   19.342865] i2c-adapter i2c-2: unable to read EDID block.
[   19.342870] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   19.347406] i2c-adapter i2c-2: unable to read EDID block.
[   19.347408] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   19.592278] i2c-adapter i2c-2: unable to read EDID block.
[   19.592282] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   19.596693] i2c-adapter i2c-2: unable to read EDID block.
[   19.596695] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   20.033614] [drm] LVDS-8: set mode 1024x768 2f
[   31.002791] i2c-adapter i2c-2: unable to read EDID block.
[   31.002795] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   31.007592] i2c-adapter i2c-2: unable to read EDID block.
[   31.007595] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   31.241116] i2c-adapter i2c-2: unable to read EDID block.
[   31.241120] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   31.245865] i2c-adapter i2c-2: unable to read EDID block.
[   31.245867] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   31.513288] i2c-adapter i2c-2: unable to read EDID block.
[   31.513292] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   31.518059] i2c-adapter i2c-2: unable to read EDID block.
[   31.518062] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   35.809923] i2c-adapter i2c-2: unable to read EDID block.
[   35.809927] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   35.814338] i2c-adapter i2c-2: unable to read EDID block.
[   35.814340] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[   44.032756] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   44.032760] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hwardware performance
[   44.032761] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[   44.032763] vboxdrv: the usage of hardware performance counters by
[   44.032764] vboxdrv:   echo 2 > /proc/sys/kernel/perf_counter_paranoid
[   44.032769] vboxdrv: Found 2 processor cores.
[   44.032851] vboxdrv: fAsync=0 offMin=0x18f offMax=0x1ae8
[   44.032903] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   44.032905] vboxdrv: Successfully loaded version 3.0.8_OSE (interface 0x000e0000).
[   46.544075] ppdev: user-space parallel port driver
[   63.227597] wlan0: authenticate with AP 00:21:91:e1:8a:90
[   63.230341] wlan0: authenticated
[   63.230345] wlan0: associate with AP 00:21:91:e1:8a:90
[   63.234199] wlan0: RX AssocResp from 00:21:91:e1:8a:90 (capab=0x411 status=0 aid=2)
[   63.234205] wlan0: associated
[   63.236508] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   63.578768] padlock: VIA PadLock not detected.
[   73.904034] wlan0: no IPv6 routers present
[   95.422018] r8169: eth0: link up
[   95.422289] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  106.032112] eth0: no IPv6 routers present
[  191.247493] iwlagn 0000:02:00.0: iwl_tx_agg_start on ra = 00:21:91:e1:8a:90 tid = 0
[  470.665462] i2c-adapter i2c-2: unable to read EDID block.
[  470.665466] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  470.669892] i2c-adapter i2c-2: unable to read EDID block.
[  470.669894] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  589.705024] i2c-adapter i2c-2: unable to read EDID block.
[  589.705030] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  589.709544] i2c-adapter i2c-2: unable to read EDID block.
[  589.709550] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  590.174374] i2c-adapter i2c-2: unable to read EDID block.
[  590.174380] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  590.179056] i2c-adapter i2c-2: unable to read EDID block.
[  590.179061] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  590.697207] i2c-adapter i2c-2: unable to read EDID block.
[  590.697213] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  590.701763] i2c-adapter i2c-2: unable to read EDID block.
[  590.701766] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  592.159552] i2c-adapter i2c-2: unable to read EDID block.
[  592.159556] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  592.164101] i2c-adapter i2c-2: unable to read EDID block.
[  592.164104] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  592.816357] i2c-adapter i2c-2: unable to read EDID block.
[  592.816364] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  592.820784] i2c-adapter i2c-2: unable to read EDID block.
[  592.820786] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  593.053731] i2c-adapter i2c-2: unable to read EDID block.
[  593.053738] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  593.058697] i2c-adapter i2c-2: unable to read EDID block.
[  593.058701] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  593.295191] i2c-adapter i2c-2: unable to read EDID block.
[  593.295196] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[  593.299967] i2c-adapter i2c-2: unable to read EDID block.
[  593.299969] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 1836.194319] i2c-adapter i2c-2: unable to read EDID block.
[ 1836.194324] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 1836.199125] i2c-adapter i2c-2: unable to read EDID block.
[ 1836.199128] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 2598.429527] i2c-adapter i2c-2: unable to read EDID block.
[ 2598.429534] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 2598.433968] i2c-adapter i2c-2: unable to read EDID block.
[ 2598.433972] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 3294.689723] i2c-adapter i2c-2: unable to read EDID block.
[ 3294.689727] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 3294.694171] i2c-adapter i2c-2: unable to read EDID block.
[ 3294.694173] i915 0000:00:02.0: HDMI Type A-1: no EDID data
[ 5285.442442] wlan0: disassociating by local choice (reason=3)
[ 5306.928451] wlan0: authenticate with AP 00:21:91:e1:8a:90
[ 5306.930654] wlan0: authenticated
[ 5306.930660] wlan0: associate with AP 00:21:91:e1:8a:90
[ 5306.934787] wlan0: RX AssocResp from 00:21:91:e1:8a:90 (capab=0x411 status=0 aid=2)
[ 5306.934793] wlan0: associated
[ 5360.554696] r8169: eth0: link down
[ 5366.816372] r8169: eth0: link up
[ 5373.109521] wlan0: disassociating by local choice (reason=3)
[ 5386.427637] wlan0: authenticate with AP 00:21:91:e1:8a:90
[ 5386.430773] wlan0: authenticated
[ 5386.430777] wlan0: associate with AP 00:21:91:e1:8a:90
[ 5386.434755] wlan0: RX AssocResp from 00:21:91:e1:8a:90 (capab=0x411 status=0 aid=2)
[ 5386.434759] wlan0: associated
[ 5401.861248] __ratelimit: 6 callbacks suppressed
[ 5401.861251] type=1503 audit(1274302036.779:14): operation="capable" pid=4838 parent=1 profile="/usr/sbin/ntpd" name="dac_override"
[ 5562.292519] r8169: eth0: link down
[ 5562.808081] wlan0: no probe response from AP 00:21:91:e1:8a:90 - disassociating
[ 5565.017759] r8169: eth0: link up
[ 5622.722946] wlan0: authenticate with AP 00:21:91:e1:8a:90
[ 5622.723318] wlan0: authenticate with AP 00:21:91:e1:8a:90
[ 5622.725329] wlan0: authenticated
[ 5622.725334] wlan0: associate with AP 00:21:91:e1:8a:90
[ 5622.729224] wlan0: RX ReassocResp from 00:21:91:e1:8a:90 (capab=0x411 status=0 aid=1)
[ 5622.729231] wlan0: associated
[ 5657.578178] iwlagn 0000:02:00.0: iwl_tx_agg_start on ra = 00:21:91:e1:8a:90 tid = 0
[ 6172.637620] Monitor-Mwait will be used to enter C-3 state
[ 7158.882223] r8169: eth0: link down
[ 7179.166310] r8169: eth0: link up
[ 7754.496091] usb 6-2: new full speed USB device using uhci_hcd and address 2
[ 7754.621989] usb 6-2: device descriptor read/64, error -71
[ 7754.900056] usb 6-2: device descriptor read/64, error -71
[ 7755.116057] usb 6-2: new full speed USB device using uhci_hcd and address 3
[ 7755.236059] usb 6-2: device descriptor read/64, error -71
[ 7755.464081] usb 6-2: device descriptor read/64, error -71
[ 7755.681059] usb 6-2: new full speed USB device using uhci_hcd and address 4
[ 7756.097470] usb 6-2: device not accepting address 4, error -71
[ 7756.208091] usb 6-2: new full speed USB device using uhci_hcd and address 5
[ 7756.617098] usb 6-2: device not accepting address 5, error -71
[ 7756.617123] hub 6-0:1.0: unable to enumerate USB device on port 2
[ 7786.945077] usb 6-2: new full speed USB device using uhci_hcd and address 6
[ 7787.068089] usb 6-2: device descriptor read/64, error -71
[ 7787.293054] usb 6-2: device descriptor read/64, error -71
[ 7787.508855] usb 6-2: new full speed USB device using uhci_hcd and address 7
[ 7787.628069] usb 6-2: device descriptor read/64, error -71
[ 7787.852074] usb 6-2: device descriptor read/64, error -71
[ 7788.069067] usb 6-2: new full speed USB device using uhci_hcd and address 8
[ 7788.480048] usb 6-2: device not accepting address 8, error -71
[ 7788.592082] usb 6-2: new full speed USB device using uhci_hcd and address 9
[ 7789.001048] usb 6-2: device not accepting address 9, error -71
[ 7789.001076] hub 6-0:1.0: unable to enumerate USB device on port 2
[ 8135.556203] usb 6-2: new full speed USB device using uhci_hcd and address 10
[ 8135.676058] usb 6-2: device descriptor read/64, error -71
[ 8135.900113] usb 6-2: device descriptor read/64, error -71
[ 8136.116067] usb 6-2: new full speed USB device using uhci_hcd and address 11
[ 8136.236115] usb 6-2: device descriptor read/64, error -75
[ 8136.464066] usb 6-2: device descriptor read/64, error -71
[ 8136.680064] usb 6-2: new full speed USB device using uhci_hcd and address 12
[ 8137.088066] usb 6-2: device not accepting address 12, error -71
[ 8137.200079] usb 6-2: new full speed USB device using uhci_hcd and address 13
[ 8137.616466] usb 6-2: device not accepting address 13, error -71
[ 8137.616495] hub 6-0:1.0: unable to enumerate USB device on port 2
[ 8143.436068] usb 6-2: new full speed USB device using uhci_hcd and address 14
[ 8143.556054] usb 6-2: device descriptor read/64, error -71
[ 8143.781055] usb 6-2: device descriptor read/64, error -71
[ 8144.000075] usb 6-2: new full speed USB device using uhci_hcd and address 15
[ 8144.120075] usb 6-2: device descriptor read/64, error -71
[ 8144.344071] usb 6-2: device descriptor read/64, error -71
[ 8144.560106] usb 6-2: new full speed USB device using uhci_hcd and address 16
[ 8144.969423] usb 6-2: device not accepting address 16, error -71
[ 8145.080614] usb 6-2: new full speed USB device using uhci_hcd and address 17
[ 8145.492064] usb 6-2: device not accepting address 17, error -71
[ 8145.492093] hub 6-0:1.0: unable to enumerate USB device on port 2
[ 8150.745053] usb 6-2: new full speed USB device using uhci_hcd and address 18
[ 8150.864066] usb 6-2: device descriptor read/64, error -71
[ 8151.088054] usb 6-2: device descriptor read/64, error -71
[ 8151.304086] usb 6-2: new full speed USB device using uhci_hcd and address 19
[ 8151.424633] usb 6-2: device descriptor read/64, error -71
[ 8151.648093] usb 6-2: device descriptor read/64, error -75
[ 8151.864095] usb 6-2: new full speed USB device using uhci_hcd and address 20
[ 8152.272528] usb 6-2: device not accepting address 20, error -71
[ 8152.385078] usb 6-2: new full speed USB device using uhci_hcd and address 21
[ 8152.793073] usb 6-2: device not accepting address 21, error -71
[ 8152.793099] hub 6-0:1.0: unable to enumerate USB device on port 2
[ 8367.752063] usb 6-2: new full speed USB device using uhci_hcd and address 22
[ 8367.873056] usb 6-2: device descriptor read/64, error -71
[ 8368.100084] usb 6-2: device descriptor read/64, error -71
[ 8368.312090] usb 6-2: new full speed USB device using uhci_hcd and address 23
[ 8368.432101] usb 6-2: device descriptor read/64, error -71
[ 8368.660071] usb 6-2: device descriptor read/64, error -71
[ 8368.876101] usb 6-2: new full speed USB device using uhci_hcd and address 24
[ 8369.289052] usb 6-2: device not accepting address 24, error -71
[ 8369.401056] usb 6-2: new full speed USB device using uhci_hcd and address 25
[ 8369.812347] usb 6-2: device not accepting address 25, error -71
[ 8369.812374] hub 6-0:1.0: unable to enumerate USB device on port 2
[18134.429031] CE: hpet increasing min_delta_ns to 15000 nsec
[31752.616087] usb 6-2: new full speed USB device using uhci_hcd and address 26
[31752.740055] usb 6-2: device descriptor read/64, error -71
[31752.962335] usb 6-2: device descriptor read/64, error -71
[31753.176139] usb 6-2: new full speed USB device using uhci_hcd and address 27
[31753.296082] usb 6-2: device descriptor read/64, error -75
[31753.520700] usb 6-2: device descriptor read/64, error -71
[31753.737054] usb 6-2: new full speed USB device using uhci_hcd and address 28
[31754.144100] usb 6-2: device not accepting address 28, error -75
[31754.257062] usb 6-2: new full speed USB device using uhci_hcd and address 29
[31754.675548] usb 6-2: device not accepting address 29, error -75
[31754.675579] hub 6-0:1.0: unable to enumerate USB device on port 2


[Prsatá blondýna]

omg. lo je lokalni smycka je  mi líto, ale pokud máš v PC 2 sitovky takto tu druhou asi nevidi
pro pochopeni poslu svuj vypis. ja mam jen jednu sitovou a jednu wifi kartu

Kód: [Vybrat]

root@stet-laptop:/home/stet# ifconfig -a
eth0      Link encap:Ethernet  HWadr 00:22:15:fc:80:40 
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:581026 errors:0 dropped:0 overruns:0 frame:0
          TX packets:433381 errors:0 dropped:0 overruns:0 carrier:38
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 873303540 (873.3 MB) Odesláno bajtů: 30102875 (30.1 MB)
          Přerušení:28

lo        Link encap:Místní smyčka 
          inet adr:127.0.0.1  Maska:255.0.0.0
          inet6-adr: ::1/128 Rozsah:Počítač
          AKTIVOVÁNO SMYČKA BĚŽÍ  MTU:16436  Metrika:1
          RX packets:78541 errors:0 dropped:0 overruns:0 frame:0
          TX packets:78541 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 10122540 (10.1 MB) Odesláno bajtů: 10122540 (10.1 MB)

wlan0     Link encap:Ethernet  HWadr 00:22:43:00:aa:29 
          inet adr:192.168.3.47  Všesměr:192.168.3.255  Maska:255.255.255.0
          inet6-adr: fe80::222:43ff:fe00:aa29/64 Rozsah:Linka
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:125800 errors:0 dropped:0 overruns:0 frame:0
          TX packets:20872 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          Přijato bajtů: 19616527 (19.6 MB) Odesláno bajtů: 4370743 (4.3 MB)
          Přerušení:19

root@stet-laptop:/home/stet#


[jmp]

ja tam opravdu vidim dva adaptery
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
01:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)

zkuste dat
sudo ethtool -i eth0
sudo ethtool -i eth1
to by melo vypsat jake ovladace to ktere zarizeni pouziva

[Prsatá blondýna]

a neni ta druha nahodou vypnuta ?

sudo ifconfig ethx up


za x dopln cislo te karty

[locus]

no tak karta je asi nefunkční koupil jsem novou.
tedy budu postupovat takto:
1 vypnu pc
2 připojím PCIe x1 sí/tovou kartu TP-LINK, je podporovaná linuxu.
http://www.alfacomp.cz/php/product.php?eid=105140006000000RJF&Search=s%ED%9Dov%E1%20karta&SearchType=1
3 zapnu pc.

potom pls co?
Dělám tyto kroky správně ?

[locus]

no tak asi se zadarilo po zadáni ifconfig se obě ukážou.

ted jeste resim takovou blbost jede natom apache s bloge a na jednu sitovku je jedna onektivita a na druhou je druhá. Na obou je DMZ a na obě konektivity je jedna domena s tímže jednou jede ta jedna domena ktera je na jedne konektivita a podruhe druha.

nevite pls co to zpusobuje?

děkuju moc.

[jmp]

nevim, jak ostatni, ale ja tohle nepochopil - zkuste to popsat nejak jinak
stejne je to uz ale jiny problem, ktery by zaslouzil sve vlastni vlakno...

[locus]

Ano, děkuju moc moc všem za pomoc s rešením.

Děkuju