Prosíme přihlašte se nebo zaregistrujte.

Přihlašte se svým uživatelským jménem a heslem.
Vaše pomoc je stále potřeba!

Autor Téma: Je to opravdu problém rozjet wifinu Broadcom 4318? [vyřešeno]  (Přečteno 5235 krát)

Michal66

  • Návštěvník
  • Příspěvků: 68
Sorry že se takhle ptám,ale už mě to trochu štve,je tady hafo návodů jak rozjet wifi,ale na verzi 10.04 nic.
A největší perla je že v live cd to fungovalo,mám Broadcom 4318,Ubuntu je nainstalovaný na externím disku,přes ndiswrapper to nejede,b43-cutter taky nic,bcmwl-kernel-source taky nepomáhá.

Kód: [Vybrat]
michal@michal-laptop:~$ lspci | grep -i Broadcom
04:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
michal@michal-laptop:~$ sudo rmmod bcm43xx
[sudo] password for michal:
ERROR: Module bcm43xx does not exist in /proc/modules
michal@michal-laptop:~$ sudo ndiswrapper -i bcmwl5a.inf
couldn't open bcmwl5a.inf: No such file or directory at /usr/sbin/ndiswrapper-1.9 line 219.
michal@michal-laptop:~$ ndiswrapper -l
michal@michal-laptop:~$ sudo modprobe ndiswrapper
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
michal@michal-laptop:~$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

michal@michal-laptop:~$

« Poslední změna: 14 Června 2010, 12:01:20 od Michal66 »
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #1 kdy: 13 Června 2010, 16:46:27 »
Žádám o smazání mého příspěvku,stejně to nikdo neví.Nemyslete,že jsem nepoužil návody co jsou tady,asi už vím kde je chyba,chyba je asi v tomhle distru,ono to v live cd jede ale pokud instalujete a dáte aktualizaci systému,tak to už nepůjde,dokonce ten ovladač není ani v nabídce pod nesvobodnými ovladači,takže pokud máte tento typ Broadcom 4318 tak jednoznačně Ubuntu 10.04 nedoporučuji,přece nechcete trávit čas s takovou samozřejmostí jako je wifi  ;).
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Habo

  • Návštěvník
  • Příspěvků: 94
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #2 kdy: 13 Června 2010, 17:45:17 »
No tak pockat
Co tak skusit modprobe bcmwl ? (alebo tak nejako, mozno to bolo modprobe wl ...)
Sesternici to tiez neslo a toto to vyriesilo,
inac odporucam kupovat wifiny od intelu - doteraz som s nimi nemal problem...

Martin Kiklhorn

  • Člen občanského sdružení Ubuntu ČR a placené komunitní podpory
  • Administrátor fóra
  • Závislák
  • ******
  • Příspěvků: 4807
  • グーグル!ご存知ですか?
    • HEJ
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #3 kdy: 13 Června 2010, 17:58:06 »
v live se podívejte na
Kód: [Vybrat]
lsmod
lspci -vnnk
a uložte to třeba na pastebin
 pak se nechá porovnat co chybí/je navíc v nainstalované verzi.
« Poslední změna: 13 Června 2010, 18:00:33 od kiklhorn »
Jsou ve vašem dotazu OPRAVDU VŠECHNY vám dostupné informace o problému?
Linux user since 2007-10-11, Registered #456007
Virtual
| Distribuce
~/slozka znamená /home/"vase jmeno"/slozka
6521 69DE 0F34 FCBC FB1D  DE76 360E 52B2 F71A B8E8

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #4 kdy: 13 Června 2010, 18:10:05 »
OK mnt
Neberte život příliš vážně, stejně z něho nevyváznete živý.

TIBOR

  • Závislák
  • ***
  • Příspěvků: 6529
  • Som uzivatel linuxovej distribucie, som linuxak?
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #5 kdy: 13 Června 2010, 18:12:29 »
Ja sice taku wifi nemam ale podla wifi treba nahrat novy firmvare
http://wiki.ubuntu.cz/BCM4318?highlight=%28Broadcom%29|%284318%29#Ubuntu_9.10
alebo to uz v 10.04 nefunguje?
HP Laptop 17-ca1xxx Ubuntu Mate 22.04 FF 64bit.
Asus X751LB-TY014H Ubuntu Mate 20.04.1 FF 64bit.
Linus, Lajnas, Línus, Luínus, Lajnus a je mi naozaj jedno, ako ľudia vyslovujú moje meno. Ale "Linux" je vždy "Linux". LINUS TORVALDS, tvorca Linuxového jadra.(V dokumente Revolution OS)

petertomasy

  • Stálý člen
  • **
  • Příspěvků: 856
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #6 kdy: 13 Června 2010, 18:15:20 »

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #7 kdy: 13 Června 2010, 18:38:56 »
Výpis z live cd:

Kód: [Vybrat]
To run a command as administrator (user "root"), use "sudo <command>".
See "man sudo_root" for details.

ubuntu@ubuntu:~$ lsmod
Module                  Size  Used by
binfmt_misc             6587  1
ppdev                   5259  0
lp                      7028  0
parport                32635  2 ppdev,lp
dm_crypt               11331  0
snd_hda_codec_si3054     3396  1
snd_hda_codec_realtek   203168  1
snd_hda_intel          21877  2
snd_hda_codec          74201  3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep               5412  1 snd_hda_codec
snd_pcm_oss            35308  0
snd_mixer_oss          13746  1 snd_pcm_oss
snd_pcm                70662  4 snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy           1338  0
snd_seq_oss            26726  0
snd_seq_midi            4557  0
arc4                    1153  2
snd_rawmidi            19056  1 snd_seq_midi
snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
snd_seq                47263  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
b43                   157218  0
pcmcia                 33024  0
snd_timer              19098  2 snd_pcm,snd_seq
yenta_socket           20408  1
snd_seq_device          5700  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
rsrc_nonstatic         10015  1 yenta_socket
mac80211              204922  1 b43
sdhci_pci               5470  0
joydev                  8708  0
snd                    54148  17 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
asus_laptop            17008  0
sdhci                  15462  1 sdhci_pci
pcmcia_core            32964  3 pcmcia,yenta_socket,rsrc_nonstatic
cfg80211              126485  2 b43,mac80211
soundcore               6620  1 snd
led_class               2864  3 b43,asus_laptop,sdhci
psmouse                63245  0
snd_page_alloc          7076  2 snd_hda_intel,snd_pcm
i2c_nforce2             5199  0
k8temp                  3024  0
serio_raw               3978  0
squashfs               20680  1
aufs                  149050  1
isofs                  29250  1
nls_iso8859_1           3249  0
nls_cp437               4919  1
vfat                    8901  0
fat                    47767  1 vfat
dm_raid45              81647  0
xor                    15028  1 dm_raid45
fbcon                  35102  71
tileblit                2031  1 fbcon
font                    7557  1 fbcon
bitblit                 4707  1 fbcon
softcursor              1189  1 bitblit
vga16fb                11385  0
vgastate                8961  1 vga16fb
usbhid                 36110  0
hid                    67032  1 usbhid
nouveau               467048  2
ttm                    49943  1 nouveau
drm_kms_helper         29297  1 nouveau
ohci1394               26950  0
usb_storage            39425  1
drm                   162471  4 nouveau,ttm,drm_kms_helper
ssb                    37336  1 b43
ieee1394               81181  1 ohci1394
pata_amd                8766  1
agpgart                31724  2 ttm,drm
i2c_algo_bit            5028  1 nouveau
r8169                  33884  0
mii                     4381  1 r8169
video                  17375  0
output                  1871  1 video
ramzswap                6362  1
xvmalloc                4074  1 ramzswap
lzo_decompress          2189  1 ramzswap
lzo_compress            1853  1 ramzswap
ubuntu@ubuntu:~$ lspci -vnnk
00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f3] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0 [10de:02fa] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1 [10de:02fe] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5 [10de:02f8] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4 [10de:02f9] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0

00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3 [10de:027f] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2 [10de:027e] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:02.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fc] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:03.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fd] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df600000-df6fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:04.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fb] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:05.0 VGA compatible controller [0300]: nVidia Corporation C51 [GeForce Go 6100] [10de:0247] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at dd000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at df5e0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nouveau
Kernel modules: nvidiafb, nouveau

00:09.0 RAM memory [0500]: nVidia Corporation MCP51 Host Bridge [10de:0270] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0

00:0a.1 SMBus [0c05]: nVidia Corporation MCP51 SMBus [10de:0264] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: 66MHz, fast devsel, IRQ 5
I/O ports at 0600 [size=64]
I/O ports at 0700 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2

00:0a.3 Co-processor [0b40]: nVidia Corporation MCP51 PMU [10de:0271] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 10
Memory at df580000 (32-bit, non-prefetchable) [size=256K]

00:0b.0 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026d] (rev a3) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
Memory at df5de000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

00:0b.1 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026e] (rev a3) (prog-if 20)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at df5dfc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

00:0d.0 IDE interface [0101]: nVidia Corporation MCP51 IDE [10de:0265] (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
Kernel modules: pata_amd

00:10.0 PCI bridge [0604]: nVidia Corporation MCP51 PCI Bridge [10de:026f] (rev a2) (prog-if 01)
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=08, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: df700000-dfffffff
Prefetchable memory behind bridge: db000000-dcffffff
Capabilities: <access denied>

00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio [10de:026c] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
Memory at df5d8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Flags: fast devsel
Capabilities: <access denied>

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Flags: fast devsel

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Flags: fast devsel

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Flags: fast devsel
Kernel driver in use: k8temp
Kernel modules: k8temp

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:11f5]
Flags: bus master, fast devsel, latency 0, IRQ 27
I/O ports at d800 [size=256]
Memory at df6ff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at df6e0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

04:01.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 168, IRQ 19
Memory at df700000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 0000e400-0000e4ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket

04:01.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] (rev 08) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at df7ff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: firewire-ohci, ohci1394

04:01.2 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 17)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at df7ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci

04:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 08)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: medium devsel, IRQ 5
Memory at df7ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

04:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:120f]
Flags: bus master, fast devsel, latency 64, IRQ 19
Memory at df7fc000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb

ubuntu@ubuntu:~$
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #8 kdy: 13 Června 2010, 18:41:12 »
Výpis z notesu:

Kód: [Vybrat]
michal@michal-laptop:~$ lsmod
Module                  Size  Used by
nls_iso8859_1           3249  1
nls_cp437               4919  1
vfat                    8901  1
fat                    47767  1 vfat
binfmt_misc             6587  1
ppdev                   5259  0
snd_hda_codec_si3054     3396  1
snd_hda_codec_realtek   203168  1
snd_hda_intel          21877  2
snd_hda_codec          74201  3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep               5412  1 snd_hda_codec
snd_pcm_oss            35308  0
snd_mixer_oss          13746  1 snd_pcm_oss
snd_pcm                70662  4 snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy           1338  0
snd_seq_oss            26726  0
snd_seq_midi            4557  0
snd_rawmidi            19056  1 snd_seq_midi
snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
snd_seq                47263  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
lp                      7028  0
snd_timer              19098  2 snd_pcm,snd_seq
snd_seq_device          5700  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
pcmcia                 33024  0
fbcon                  35102  71
joydev                  8708  0
tileblit                2031  1 fbcon
parport                32635  2 ppdev,lp
snd                    54148  17 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
nvidia               9961216  40
psmouse                63245  0
i2c_nforce2             5199  0
yenta_socket           20408  1
rsrc_nonstatic         10015  1 yenta_socket
font                    7557  1 fbcon
bitblit                 4707  1 fbcon
softcursor              1189  1 bitblit
pcmcia_core            32964  3 pcmcia,yenta_socket,rsrc_nonstatic
sdhci_pci               5470  0
sdhci                  15462  1 sdhci_pci
soundcore               6620  1 snd
asus_laptop            17008  0
ndiswrapper           184677  0
snd_page_alloc          7076  2 snd_hda_intel,snd_pcm
video                  17375  0
agpgart                31724  1 nvidia
vga16fb                11385  1
vgastate                8961  1 vga16fb
output                  1871  1 video
k8temp                  3024  0
serio_raw               3978  0
led_class               2864  2 sdhci,asus_laptop
usbhid                 36110  0
hid                    67032  1 usbhid
ohci1394               26950  0
usb_storage            39425  4
ieee1394               81181  1 ohci1394
pata_amd                8766  0
r8169                  33980  0
mii                     4381  1 r8169
michal@michal-laptop:~$ lspci -vnnk
00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f3] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0 [10de:02fa] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1 [10de:02fe] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5 [10de:02f8] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4 [10de:02f9] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0

00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3 [10de:027f] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2 [10de:027e] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:02.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fc] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:03.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fd] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df600000-df6fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:04.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fb] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:05.0 VGA compatible controller [0300]: nVidia Corporation C51 [GeForce Go 6100] [10de:0247] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 19
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at dd000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at df5e0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidia-current, nvidiafb, nouveau

00:09.0 RAM memory [0500]: nVidia Corporation MCP51 Host Bridge [10de:0270] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0

00:0a.1 SMBus [0c05]: nVidia Corporation MCP51 SMBus [10de:0264] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: 66MHz, fast devsel, IRQ 5
I/O ports at 0600 [size=64]
I/O ports at 0700 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2

00:0a.3 Co-processor [0b40]: nVidia Corporation MCP51 PMU [10de:0271] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 10
Memory at df580000 (32-bit, non-prefetchable) [size=256K]

00:0b.0 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026d] (rev a3) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
Memory at df5de000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

00:0b.1 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026e] (rev a3) (prog-if 20)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at df5dfc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

00:0d.0 IDE interface [0101]: nVidia Corporation MCP51 IDE [10de:0265] (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
Kernel modules: pata_amd

00:10.0 PCI bridge [0604]: nVidia Corporation MCP51 PCI Bridge [10de:026f] (rev a2) (prog-if 01)
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=08, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: df700000-dfffffff
Prefetchable memory behind bridge: db000000-dcffffff
Capabilities: <access denied>

00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio [10de:026c] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
Memory at df5d8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Flags: fast devsel
Capabilities: <access denied>

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Flags: fast devsel

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Flags: fast devsel

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Flags: fast devsel
Kernel driver in use: k8temp
Kernel modules: k8temp

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:11f5]
Flags: bus master, fast devsel, latency 0, IRQ 27
I/O ports at d800 [size=256]
Memory at df6ff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at df6e0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

04:01.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 168, IRQ 19
Memory at df700000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 0000e400-0000e4ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket

04:01.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] (rev 08) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at df7ff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: firewire-ohci, ohci1394

04:01.2 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 17)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 64, IRQ 16
Memory at df7ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci

04:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 08)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: medium devsel, IRQ 5
Memory at df7ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

04:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:120f]
Flags: bus master, fast devsel, latency 64, IRQ 10
Memory at df7fc000 (32-bit, non-prefetchable) [size=8K]
Kernel modules: ssb

michal@michal-laptop:~$
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Martin Kiklhorn

  • Člen občanského sdružení Ubuntu ČR a placené komunitní podpory
  • Administrátor fóra
  • Závislák
  • ******
  • Příspěvků: 4807
  • グーグル!ご存知ですか?
    • HEJ
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #9 kdy: 13 Června 2010, 18:51:01 »
Kód: [Vybrat]
4:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:120f]
Flags: bus master, fast devsel, latency 64, IRQ 19
Memory at df7fc000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb

Kód: [Vybrat]
04:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:120f]
Flags: bus master, fast devsel, latency 64, IRQ 10
Memory at df7fc000 (32-bit, non-prefetchable) [size=8K]
Kernel modules: ssb

takže bych zkusil
Kód: [Vybrat]
modprobe b43 ssba podívat se na konec logu
Kód: [Vybrat]
dmesgco to vypsalo, příp. jestli už wifi nefunguje.
Jsou ve vašem dotazu OPRAVDU VŠECHNY vám dostupné informace o problému?
Linux user since 2007-10-11, Registered #456007
Virtual
| Distribuce
~/slozka znamená /home/"vase jmeno"/slozka
6521 69DE 0F34 FCBC FB1D  DE76 360E 52B2 F71A B8E8

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #10 kdy: 13 Června 2010, 18:57:39 »
Nefunguje

Kód: [Vybrat]
[    0.135838] pci 0000:00:05.0: reg 10 32bit mmio: [0xde000000-0xdeffffff]
[    0.135845] pci 0000:00:05.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
[    0.135853] pci 0000:00:05.0: reg 1c 64bit mmio: [0xdd000000-0xddffffff]
[    0.135860] pci 0000:00:05.0: reg 30 32bit mmio pref: [0xdf5e0000-0xdf5fffff]
[    0.136073] HPET not enabled in BIOS. You might try hpet=force boot option
[    0.136121] pci 0000:00:0a.1: reg 20 io port: [0x600-0x63f]
[    0.136128] pci 0000:00:0a.1: reg 24 io port: [0x700-0x73f]
[    0.136154] pci 0000:00:0a.1: PME# supported from D3hot D3cold
[    0.136161] pci 0000:00:0a.1: PME# disabled
[    0.136197] pci 0000:00:0a.3: reg 10 32bit mmio: [0xdf580000-0xdf5bffff]
[    0.136291] pci 0000:00:0b.0: reg 10 32bit mmio: [0xdf5de000-0xdf5defff]
[    0.136323] pci 0000:00:0b.0: supports D1 D2
[    0.136326] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.136331] pci 0000:00:0b.0: PME# disabled
[    0.136360] pci 0000:00:0b.1: reg 10 32bit mmio: [0xdf5dfc00-0xdf5dfcff]
[    0.136394] pci 0000:00:0b.1: supports D1 D2
[    0.136397] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.136402] pci 0000:00:0b.1: PME# disabled
[    0.136443] pci 0000:00:0d.0: reg 20 io port: [0xffa0-0xffaf]
[    0.136536] pci 0000:00:10.1: reg 10 32bit mmio: [0xdf5d8000-0xdf5dbfff]
[    0.136573] pci 0000:00:10.1: PME# supported from D3hot D3cold
[    0.136578] pci 0000:00:10.1: PME# disabled
[    0.136754] pci 0000:02:00.0: reg 10 io port: [0xd800-0xd8ff]
[    0.136771] pci 0000:02:00.0: reg 18 64bit mmio: [0xdf6ff000-0xdf6fffff]
[    0.136789] pci 0000:02:00.0: reg 30 32bit mmio pref: [0xdf6e0000-0xdf6effff]
[    0.136823] pci 0000:02:00.0: supports D1 D2
[    0.136827] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.136833] pci 0000:02:00.0: PME# disabled
[    0.136882] pci 0000:00:03.0: bridge io port: [0xd000-0xdfff]
[    0.136887] pci 0000:00:03.0: bridge 32bit mmio: [0xdf600000-0xdf6fffff]
[    0.136958] pci 0000:04:01.0: reg 10 32bit mmio: [0x000000-0x000fff]
[    0.136975] pci 0000:04:01.0: supports D1 D2
[    0.136979] pci 0000:04:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.136984] pci 0000:04:01.0: PME# disabled
[    0.137014] pci 0000:04:01.1: reg 10 32bit mmio: [0xdf7ff000-0xdf7ff7ff]
[    0.137052] pci 0000:04:01.1: PME# supported from D0 D3hot D3cold
[    0.137058] pci 0000:04:01.1: PME# disabled
[    0.137087] pci 0000:04:01.2: reg 10 32bit mmio: [0xdf7ff800-0xdf7ff8ff]
[    0.137125] pci 0000:04:01.2: supports D1 D2
[    0.137129] pci 0000:04:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.137134] pci 0000:04:01.2: PME# disabled
[    0.137165] pci 0000:04:01.3: reg 10 32bit mmio: [0xdf7ffc00-0xdf7ffcff]
[    0.137204] pci 0000:04:01.3: supports D1 D2
[    0.137207] pci 0000:04:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.137212] pci 0000:04:01.3: PME# disabled
[    0.137238] pci 0000:04:03.0: reg 10 32bit mmio: [0xdf7fc000-0xdf7fdfff]
[    0.137297] pci 0000:00:10.0: transparent bridge
[    0.137302] pci 0000:00:10.0: bridge io port: [0xe000-0xefff]
[    0.137307] pci 0000:00:10.0: bridge 32bit mmio: [0xdf700000-0xdfffffff]
[    0.137312] pci 0000:00:10.0: bridge 32bit mmio pref: [0xdb000000-0xdcffffff]
[    0.137337] pci_bus 0000:00: on NUMA node 0
[    0.137344] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.137590] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[    0.137672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[    0.137761] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
[    0.137864] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.205358] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[    0.205608] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
[    0.205853] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *11
[    0.208034] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *5
[    0.208278] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *5
[    0.208523] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
[    0.208770] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *11
[    0.209014] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
[    0.209259] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11
[    0.209510] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7
[    0.209754] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
[    0.209999] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *10
[    0.210243] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
[    0.210488] ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *0, disabled.
[    0.210732] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *5
[    0.210983] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *10
[    0.211234] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *0, disabled.
[    0.211479] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
[    0.211768] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[    0.211896] vgaarb: device added: PCI:0000:00:05.0,decodes=io+mem,owns=io+mem,locks=none
[    0.211907] vgaarb: loaded
[    0.212048] SCSI subsystem initialized
[    0.212123] libata version 3.00 loaded.
[    0.212205] usbcore: registered new interface driver usbfs
[    0.212219] usbcore: registered new interface driver hub
[    0.212247] usbcore: registered new device driver usb
[    0.212383] ACPI: WMI: Mapper loaded
[    0.212386] PCI: Using ACPI for IRQ routing
[    0.212565] NetLabel: Initializing
[    0.212568] NetLabel:  domain hash size = 128
[    0.212570] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.212585] NetLabel:  unlabeled traffic allowed by default
[    0.214575] AppArmor: AppArmor Filesystem Enabled
[    0.214595] pnp: PnP ACPI init
[    0.214610] ACPI: bus type pnp registered
[    0.220374] pnp: PnP ACPI: found 12 devices
[    0.220377] ACPI: ACPI bus type pnp unregistered
[    0.220381] PnPBIOS: Disabled by ACPI PNP
[    0.220397] system 00:07: iomem range 0xfefe0000-0xfefe01ff has been reserved
[    0.220405] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.220409] system 00:08: ioport range 0x800-0x80f has been reserved
[    0.220413] system 00:08: ioport range 0x500-0x57f has been reserved
[    0.220416] system 00:08: ioport range 0x580-0x5ff has been reserved
[    0.220420] system 00:08: ioport range 0x800-0x87f could not be reserved
[    0.220424] system 00:08: ioport range 0x880-0x8ff has been reserved
[    0.220428] system 00:08: ioport range 0x900-0x97f has been reserved
[    0.220432] system 00:08: ioport range 0x980-0x9ff has been reserved
[    0.220436] system 00:08: ioport range 0x2000-0x207f has been reserved
[    0.220440] system 00:08: ioport range 0x2080-0x20ff has been reserved
[    0.220445] system 00:08: iomem range 0xfee01000-0xfeefffff has been reserved
[    0.220449] system 00:08: iomem range 0x1c000000-0x1fffffff has been reserved
[    0.220456] system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.220460] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.220467] system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
[    0.220473] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
[    0.220477] system 00:0b: iomem range 0xc0000-0xcffff could not be reserved
[    0.220481] system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
[    0.220485] system 00:0b: iomem range 0x100000-0x1bffffff could not be reserved
[    0.220489] system 00:0b: iomem range 0xe0000000-0xffffffff could not be reserved
[    0.255193] Switching to clocksource acpi_pm
[    0.255317] pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
[    0.255320] pci 0000:00:02.0:   IO window: disabled
[    0.255323] pci 0000:00:02.0:   MEM window: disabled
[    0.255326] pci 0000:00:02.0:   PREFETCH window: disabled
[    0.255331] pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
[    0.255335] pci 0000:00:03.0:   IO window: 0xd000-0xdfff
[    0.255339] pci 0000:00:03.0:   MEM window: 0xdf600000-0xdf6fffff
[    0.255343] pci 0000:00:03.0:   PREFETCH window: disabled
[    0.255347] pci 0000:00:04.0: PCI bridge, secondary bus 0000:03
[    0.255349] pci 0000:00:04.0:   IO window: disabled
[    0.255353] pci 0000:00:04.0:   MEM window: disabled
[    0.255356] pci 0000:00:04.0:   PREFETCH window: disabled
[    0.255368] pci 0000:04:01.0: CardBus bridge, secondary bus 0000:05
[    0.255372] pci 0000:04:01.0:   IO window: 0x00e000-0x00e0ff
[    0.255377] pci 0000:04:01.0:   IO window: 0x00e400-0x00e4ff
[    0.255382] pci 0000:04:01.0:   PREFETCH window: 0x20000000-0x23ffffff
[    0.255387] pci 0000:04:01.0:   MEM window: 0x24000000-0x27ffffff
[    0.255392] pci 0000:00:10.0: PCI bridge, secondary bus 0000:04
[    0.255395] pci 0000:00:10.0:   IO window: 0xe000-0xefff
[    0.255400] pci 0000:00:10.0:   MEM window: 0xdf700000-0xdfffffff
[    0.255405] pci 0000:00:10.0:   PREFETCH window: 0xdb000000-0xdcffffff
[    0.255417] pci 0000:00:02.0: setting latency timer to 64
[    0.255423] pci 0000:00:03.0: setting latency timer to 64
[    0.255429] pci 0000:00:04.0: setting latency timer to 64
[    0.255434] pci 0000:00:10.0: setting latency timer to 64
[    0.255784] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
[    0.255788]   alloc irq_desc for 19 on node -1
[    0.255791]   alloc kstat_irqs on node -1
[    0.255802] pci 0000:04:01.0: PCI INT A -> Link[LNKB] -> GSI 19 (level, low) -> IRQ 19
[    0.255809] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.255813] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.255817] pci_bus 0000:02: resource 0 io:  [0xd000-0xdfff]
[    0.255820] pci_bus 0000:02: resource 1 mem: [0xdf600000-0xdf6fffff]
[    0.255824] pci_bus 0000:04: resource 0 io:  [0xe000-0xefff]
[    0.255827] pci_bus 0000:04: resource 1 mem: [0xdf700000-0xdfffffff]
[    0.255831] pci_bus 0000:04: resource 2 pref mem [0xdb000000-0xdcffffff]
[    0.255834] pci_bus 0000:04: resource 3 io:  [0x00-0xffff]
[    0.255838] pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffff]
[    0.255841] pci_bus 0000:05: resource 0 io:  [0xe000-0xe0ff]
[    0.255845] pci_bus 0000:05: resource 1 io:  [0xe400-0xe4ff]
[    0.255848] pci_bus 0000:05: resource 2 pref mem [0x20000000-0x23ffffff]
[    0.255851] pci_bus 0000:05: resource 3 mem: [0x24000000-0x27ffffff]
[    0.255893] NET: Registered protocol family 2
[    0.256001] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.256001] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.256001] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.256001] TCP: Hash tables configured (established 16384 bind 16384)
[    0.256001] TCP reno registered
[    0.256001] NET: Registered protocol family 1
[    0.256001] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.256001] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.256001] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    0.256001] pci 0000:00:05.0: Boot video device
[    1.056025] pci 0000:00:0b.0: OHCI: BIOS handoff failed (BIOS bug?) 000007b4
[    2.656025] pci 0000:00:0b.1: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[    2.656182] pci 0000:00:09.0: Found enabled HT MSI Mapping
[    2.656233] pci 0000:00:09.0: Found enabled HT MSI Mapping
[    2.656438] cpufreq-nforce2: No nForce2 chipset.
[    2.656467] Scanning for low memory corruption every 60 seconds
[    2.656585] audit: initializing netlink socket (disabled)
[    2.656596] type=2000 audit(1276446639.656:1): initialized
[    2.669175] Trying to unpack rootfs image as initramfs...
[    2.684190] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    2.685985] VFS: Disk quotas dquot_6.5.2
[    2.686055] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.692186] fuse init (API version 7.13)
[    2.692318] msgmni has been set to 851
[    2.692575] alg: No test for stdrng (krng)
[    2.692641] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    2.692645] io scheduler noop registered
[    2.692647] io scheduler anticipatory registered
[    2.692650] io scheduler deadline registered
[    2.692705] io scheduler cfq registered (default)
[    2.692863]   alloc irq_desc for 24 on node -1
[    2.692866]   alloc kstat_irqs on node -1
[    2.692876] pcieport 0000:00:02.0: irq 24 for MSI/MSI-X
[    2.692883] pcieport 0000:00:02.0: setting latency timer to 64
[    2.692963]   alloc irq_desc for 25 on node -1
[    2.692966]   alloc kstat_irqs on node -1
[    2.692972] pcieport 0000:00:03.0: irq 25 for MSI/MSI-X
[    2.692977] pcieport 0000:00:03.0: setting latency timer to 64
[    2.693053]   alloc irq_desc for 26 on node -1
[    2.693055]   alloc kstat_irqs on node -1
[    2.693061] pcieport 0000:00:04.0: irq 26 for MSI/MSI-X
[    2.693066] pcieport 0000:00:04.0: setting latency timer to 64
[    2.693129] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    2.693158] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    2.693310] ACPI: AC Adapter [AC0] (on-line)
[    2.693395] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[    2.693406] ACPI: Sleep Button [SLPB]
[    2.693459] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[    2.704309] ACPI: Lid Switch [LID]
[    2.704402] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    2.704407] ACPI: Power Button [PWRB]
[    2.704464] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    2.704468] ACPI: Power Button [PWRF]
[    2.704851] processor LNXCPU:00: registered as cooling_device0
[    2.720768] thermal LNXTHERM:01: registered as thermal_zone0
[    2.720781] ACPI: Thermal Zone [TZ00] (50 C)
[    2.726528] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.728077] isapnp: Scanning for PnP cards...
[    2.733617] brd: module loaded
[    2.735932] loop: module loaded
[    2.737279] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[    2.737632] pata_acpi 0000:00:0d.0: setting latency timer to 64
[    2.739201] Fixed MDIO Bus: probed
[    2.739242] PPP generic driver version 2.4.2
[    2.739301] tun: Universal TUN/TAP device driver, 1.6
[    2.739304] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.740398] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.742056] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 23
[    2.742062]   alloc irq_desc for 23 on node -1
[    2.742065]   alloc kstat_irqs on node -1
[    2.742077] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[LUB2] -> GSI 23 (level, low) -> IRQ 23
[    2.742097] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[    2.742101] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[    2.742146] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[    2.742174] ehci_hcd 0000:00:0b.1: debug port 1
[    2.742183] ehci_hcd 0000:00:0b.1: cache line size of 64 is not supported
[    2.742208] ehci_hcd 0000:00:0b.1: irq 23, io mem 0xdf5dfc00
[    2.786483] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[    2.786744] usb usb1: configuration #1 chosen from 1 choice
[    2.786784] hub 1-0:1.0: USB hub found
[    2.786795] hub 1-0:1.0: 8 ports detected
[    2.787070] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.789572] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 22
[    2.789578]   alloc irq_desc for 22 on node -1
[    2.789581]   alloc kstat_irqs on node -1
[    2.789592] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[LUB0] -> GSI 22 (level, low) -> IRQ 22
[    2.789609] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[    2.789613] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[    2.789869] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[    2.789905] ohci_hcd 0000:00:0b.0: irq 22, io mem 0xdf5de000
[    2.880701] usb usb2: configuration #1 chosen from 1 choice
[    2.880738] hub 2-0:1.0: USB hub found
[    2.880752] hub 2-0:1.0: 8 ports detected
[    2.880957] uhci_hcd: USB Universal Host Controller Interface driver
[    2.881066] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    2.886777] i8042.c: Detected active multiplexing controller, rev 1.1.
[    2.895926] ACPI: Battery Slot [BAT0] (battery present)
[    2.900892] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.903165] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    2.903215] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    2.903616] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    2.903656] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    2.903963] mice: PS/2 mouse device common for all mice
[    2.905046] rtc_cmos 00:02: RTC can wake from S4
[    2.905099] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    2.905138] rtc0: alarms up to one year, y3k, 114 bytes nvram
[    2.908773] device-mapper: uevent: version 1.0.3
[    2.909147] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    2.909979] device-mapper: multipath: version 1.1.0 loaded
[    2.909983] device-mapper: multipath round-robin: version 1.0.0 loaded
[    2.912454] EISA: Probing bus 0 at eisa.0
[    2.912465] Cannot allocate resource for EISA slot 2
[    2.912485] EISA: Detected 0 cards.
[    2.913360] cpuidle: using governor ladder
[    2.913434] cpuidle: using governor menu
[    2.913954] TCP cubic registered
[    2.914144] NET: Registered protocol family 10
[    2.914683] lo: Disabled Privacy Extensions
[    2.915116] NET: Registered protocol family 17
[    2.915149] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 3200+ processors (1 cpu cores) (version 2.20.00)
[    2.915196] powernow-k8:    0 : fid 0x8 (1600 MHz), vid 0x11
[    2.915200] powernow-k8:    1 : fid 0x0 (800 MHz), vid 0x18
[    2.915237] powernow-k8: ph2 null fid transition 0x8
[    2.915260] Using IPI No-Shortcut mode
[    2.915368] PM: Resume from disk failed.
[    2.915383] registered taskstats version 1
[    2.915803]   Magic number: 14:151:540
[    2.915912] rtc_cmos 00:02: setting system clock to 2010-06-13 16:30:41 UTC (1276446641)
[    2.915917] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.915920] EDD information not available.
[    2.937482] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    3.285438] Freeing initrd memory: 7786k freed
[    3.378382] isapnp: No Plug & Play device found
[    3.378653] Freeing unused kernel memory: 656k freed
[    3.379263] Write protecting the kernel text: 4676k
[    3.379300] Write protecting the kernel read-only data: 1840k
[    3.400041] udev: starting version 151
[    3.432086] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    3.565347] usb 1-1: configuration #1 chosen from 1 choice
[    3.655279] pata_amd 0000:00:0d.0: version 0.4.1
[    3.655330] pata_amd 0000:00:0d.0: setting latency timer to 64
[    3.669826] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.670241] ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
[    3.670247]   alloc irq_desc for 18 on node -1
[    3.670250]   alloc kstat_irqs on node -1
[    3.670263] r8169 0000:02:00.0: PCI INT A -> Link[LNEA] -> GSI 18 (level, low) -> IRQ 18
[    3.670301] r8169 0000:02:00.0: setting latency timer to 64
[    3.670342]   alloc irq_desc for 27 on node -1
[    3.670344]   alloc kstat_irqs on node -1
[    3.670355] r8169 0000:02:00.0: irq 27 for MSI/MSI-X
[    3.671181] eth0: RTL8168b/8111b at 0xdc864000, 00:18:f3:38:e0:d2, XID 18000000 IRQ 27
[    3.673387] scsi0 : pata_amd
[    3.673584] scsi1 : pata_amd
[    3.675202] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    3.675206] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    3.683193] Initializing USB Mass Storage driver...
[    3.683287] scsi2 : SCSI emulation for USB Mass Storage devices
[    3.683428] usbcore: registered new interface driver usb-storage
[    3.683432] USB Mass Storage support registered.
[    3.683527] usb-storage: device found at 2
[    3.683529] usb-storage: waiting for device to settle before scanning
[    3.836377] ata1.00: ATAPI: HL-DT-ST DVDRAM GMA-4082N, HJ02, max UDMA/33
[    3.836410] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000c600) ACPI=0x701f (60:900:0x11)
[    3.852327] ata1.00: configured for UDMA/33
[    3.861613] scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GMA-4082N HJ02 PQ: 0 ANSI: 5
[    3.873412] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.873417] Uniform CD-ROM driver Revision: 3.20
[    3.873678] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    3.873816] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    3.924077] usb 2-2: new low speed USB device using ohci_hcd and address 2
[    4.036534] ata2.00: ATA-6: ST98823A, 3.06, max UDMA/100
[    4.036538] ata2.00: 156301488 sectors, multi 16: LBA48
[    4.036568] ata2: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc000c600) ACPI=0x3f01f (20:900:0x11)
[    4.052506] ata2.00: configured for UDMA/100
[    4.052604] scsi 1:0:0:0: Direct-Access     ATA      ST98823A         3.06 PQ: 0 ANSI: 5
[    4.052760] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    4.052982] sd 1:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    4.053040] sd 1:0:0:0: [sda] Write Protect is off
[    4.053043] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.053073] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.053231]  sda: sda1 sda2 < >
[    4.085948] sd 1:0:0:0: [sda] Attached SCSI disk
[    4.093733] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 17
[    4.093741]   alloc irq_desc for 17 on node -1
[    4.093743]   alloc kstat_irqs on node -1
[    4.093756] ohci1394 0000:04:01.1: PCI INT B -> Link[LNKC] -> GSI 17 (level, low) -> IRQ 17
[    4.127552] usb 2-2: configuration #1 chosen from 1 choice
[    4.145234] usbcore: registered new interface driver hiddev
[    4.150085] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[df7ff000-df7ff7ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    4.157826] input: HID 062a:0000 as /devices/pci0000:00/0000:00:0b.0/usb2/2-2/2-2:1.0/input/input6
[    4.158304] generic-usb 0003:062A:0000.0001: input,hidraw0: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:0b.0-2/input0
[    4.158335] usbcore: registered new interface driver usbhid
[    4.158459] usbhid: v2.6:USB HID core driver
[    5.432192] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800036510e8]
[    8.680192] usb-storage: device scan complete
[    8.682540] scsi 2:0:0:0: Direct-Access     WD       1600BEV External 1.05 PQ: 0 ANSI: 4
[    8.683477] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    8.684249] sd 2:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    8.686406] sd 2:0:0:0: [sdb] Write Protect is off
[    8.686412] sd 2:0:0:0: [sdb] Mode Sense: 21 00 00 00
[    8.686415] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    8.689387] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    8.689391]  sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 >
[    8.740422] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    8.740429] sd 2:0:0:0: [sdb] Attached SCSI disk
[    9.245731] EXT4-fs (sdb5): mounted filesystem with ordered data mode
[   19.250679] Adding 1299448k swap on /dev/sdb6.  Priority:-1 extents:1 across:1299448k
[   19.625411] udev: starting version 151
[   19.900851] EXT4-fs (sdb7): mounted filesystem with ordered data mode
[   19.994827] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[   20.038897] vga16fb: initializing
[   20.038902] vga16fb: mapped to 0xc00a0000
[   20.038980] fb0: VGA16 VGA frame buffer device
[   20.130212] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input7
[   20.130279] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   20.131069] Linux agpgart interface v0.103
[   20.134439] Disabling lock debugging due to kernel taint
[   20.162206] asus_laptop: Asus Laptop Support version 0.42
[   20.164728] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
[   20.169836] asus_laptop: Error calling BSTS
[   20.169843] asus_laptop:   A6M model detected
[   20.195568] sdhci: Secure Digital Host Controller Interface driver
[   20.195572] sdhci: Copyright(c) Pierre Ossman
[   20.206368] input: Asus Laptop extra buttons as /devices/virtual/input/input8
[   20.209101] sdhci-pci 0000:04:01.2: SDHCI controller found [1180:0822] (rev 17)
[   20.209524] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 16
[   20.209531]   alloc irq_desc for 16 on node -1
[   20.209533]   alloc kstat_irqs on node -1
[   20.209546] sdhci-pci 0000:04:01.2: PCI INT C -> Link[LNKD] -> GSI 16 (level, low) -> IRQ 16
[   20.211696] Registered led device: mmc0::
[   20.212846] mmc0: SDHCI controller on PCI [0000:04:01.2] using PIO
[   20.213390] Registered led device: asus::mail
[   20.311206] usbcore: registered new interface driver ndiswrapper
[   20.371139] yenta_cardbus 0000:04:01.0: CardBus bridge found [1043:1367]
[   20.387519] ACPI: resource nForce2_smbus [0x600-0x63f] conflicts with ACPI region SMRG [0x600-0x60f]
[   20.387523] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   20.387527] nForce2_smbus 0000:00:0a.1: Error probing SMB1.
[   20.387673] i2c i2c-0: nForce2 SMBus adapter at 0x700
[   20.496823] yenta_cardbus 0000:04:01.0: ISA IRQ mask 0x0cb8, PCI irq 19
[   20.496828] yenta_cardbus 0000:04:01.0: Socket status: 30000006
[   20.496833] pci_bus 0000:04: Raising subordinate bus# of parent bus (#04) from #05 to #08
[   20.496843] yenta_cardbus 0000:04:01.0: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
[   20.496848] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xe000-0xefff: clean.
[   20.497097] yenta_cardbus 0000:04:01.0: pcmcia: parent PCI bridge Memory window: 0xdf700000 - 0xdfffffff
[   20.497101] yenta_cardbus 0000:04:01.0: pcmcia: parent PCI bridge Memory window: 0xdb000000 - 0xdcffffff
[   21.179835] Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[   21.218447] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input9
[   21.907807] type=1505 audit(1276446660.489:2):  operation="profile_load" pid=649 name="/sbin/dhclient3"
[   21.908196] type=1505 audit(1276446660.492:3):  operation="profile_load" pid=649 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   21.908393] type=1505 audit(1276446660.492:4):  operation="profile_load" pid=649 name="/usr/lib/connman/scripts/dhclient-script"
[   23.796369] ACPI: PCI Interrupt Link [LNEC] enabled at IRQ 19
[   23.796377] nvidia 0000:00:05.0: PCI INT A -> Link[LNEC] -> GSI 19 (level, low) -> IRQ 19
[   23.796385] nvidia 0000:00:05.0: setting latency timer to 64
[   23.796391] vgaarb: device changed decodes: PCI:0000:00:05.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   23.797622] NVRM: loading NVIDIA UNIX x86 Kernel Module  195.36.24  Thu Apr 22 09:18:20 PDT 2010
[   24.098876] Console: switching to colour frame buffer device 80x30
[   24.253616] lp: driver loaded but no devices found
[   24.391202] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[   24.392412] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[   24.392915] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: excluding 0x828-0x82f 0x840-0x85f 0x870-0x877
[   24.393232] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[   24.393840] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[   24.928462] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[   24.928469]   alloc irq_desc for 21 on node -1
[   24.928473]   alloc kstat_irqs on node -1
[   24.928488] HDA Intel 0000:00:10.1: PCI INT B -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[   24.928493] hda_intel: Disable MSI for Nvidia chipset
[   24.928541] HDA Intel 0000:00:10.1: setting latency timer to 64
[   25.449148] r8169: eth0: link up
[   25.449156] r8169: eth0: link up
[   25.969197] hda_codec: ALC660: BIOS auto-probing.
[   26.088267] type=1505 audit(1276446664.672:5):  operation="profile_load" pid=883 name="/usr/share/gdm/guest-session/Xsession"
[   26.093597] type=1505 audit(1276446664.676:6):  operation="profile_replace" pid=885 name="/sbin/dhclient3"
[   26.093951] type=1505 audit(1276446664.676:7):  operation="profile_replace" pid=885 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   26.094159] type=1505 audit(1276446664.676:8):  operation="profile_replace" pid=885 name="/usr/lib/connman/scripts/dhclient-script"
[   26.129289] type=1505 audit(1276446664.712:9):  operation="profile_load" pid=886 name="/usr/bin/evince"
[   26.137828] type=1505 audit(1276446664.720:10):  operation="profile_load" pid=886 name="/usr/bin/evince-previewer"
[   26.144752] type=1505 audit(1276446664.728:11):  operation="profile_load" pid=886 name="/usr/bin/evince-thumbnailer"
[   26.188133] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input10
[   27.665701] ppdev: user-space parallel port driver
[   36.284015] eth0: no IPv6 routers present
[   92.604070] Clocksource tsc unstable (delta = -86001371 ns)
michal@michal-laptop:~$
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #11 kdy: 13 Června 2010, 19:00:22 »
Kód: [Vybrat]
michal@michal-laptop:~$ modprobe b43 ssb
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
WARNING: Error inserting mac80211 (/lib/modules/2.6.32-22-generic/kernel/net/mac80211/mac80211.ko): Operation not permitted
WARNING: Error inserting ssb (/lib/modules/2.6.32-22-generic/kernel/drivers/ssb/ssb.ko): Operation not permitted
FATAL: Error inserting b43 (/lib/modules/2.6.32-22-generic/kernel/drivers/net/wireless/b43/b43.ko): Operation not permitted
michal@michal-laptop:~$
Neberte život příliš vážně, stejně z něho nevyváznete živý.

arrange

  • Závislák
  • ***
  • Příspěvků: 4031
  • "jdu s hlavou vztyčenou..."
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #12 kdy: 13 Června 2010, 19:03:47 »
Kód: [Vybrat]
sudo modprobe b43 ssb
http://www.openstreetmap.org - mapy celého světa "wiki style"

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #13 kdy: 13 Června 2010, 19:07:08 »
Kód: [Vybrat]
michal@michal-laptop:~$ sudo modprobe b43 ssb
[sudo] password for michal:
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
FATAL: Error inserting b43 (/lib/modules/2.6.32-22-generic/kernel/drivers/net/wireless/b43/b43.ko): Unknown symbol in module, or unknown parameter (see dmesg)
michal@michal-laptop:~$
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Martin Kiklhorn

  • Člen občanského sdružení Ubuntu ČR a placené komunitní podpory
  • Administrátor fóra
  • Závislák
  • ******
  • Příspěvků: 4807
  • グーグル!ご存知ですか?
    • HEJ
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #14 kdy: 13 Června 2010, 19:57:58 »
a dál?
Jsou ve vašem dotazu OPRAVDU VŠECHNY vám dostupné informace o problému?
Linux user since 2007-10-11, Registered #456007
Virtual
| Distribuce
~/slozka znamená /home/"vase jmeno"/slozka
6521 69DE 0F34 FCBC FB1D  DE76 360E 52B2 F71A B8E8

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #15 kdy: 13 Června 2010, 20:01:51 »
Kód: [Vybrat]
michal@michal-laptop:~$ sudo modprobe b43 ssb
[sudo] password for michal:
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
FATAL: Error inserting b43 (/lib/modules/2.6.32-22-generic/kernel/drivers/net/wireless/b43/b43.ko): Unknown symbol in module, or unknown parameter (see dmesg)
michal@michal-laptop:~$

Dál už nic
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Yontalcar

  • Stálý člen
  • **
  • Příspěvků: 833
  • Semper fidelis
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #16 kdy: 13 Června 2010, 21:56:50 »
takže bych zkusil
Kód: [Vybrat]
modprobe b43 ssb
uff..
nemůžeš modprobovat 2 moduly naráz - další parametry jsou předávány jako parametry modulu
takže jenom
Kód: [Vybrat]
sudo modprobe b43
NB: ASUS X53U - AMD Brazos E450; Debian GNU/Linux Sid amd64 (KDE 4.14)
Jen dvě věci jsou nekonečné - vesmír a lidská hloupost. Tím prvním si ovšem nejsem tak jist. - Albert Einstein

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu?Pomůže někdo?
« Odpověď #17 kdy: 13 Června 2010, 23:25:42 »
takže bych zkusil
Kód: [Vybrat]
modprobe b43 ssb
uff..
nemůžeš modprobovat 2 moduly naráz - další parametry jsou předávány jako parametry modulu
takže jenom
Kód: [Vybrat]
sudo modprobe b43

Vyřešeno:

příkaz sudo modprobe b43

poté jsem přes Synaptic instaloval ndiswrapper

v nesvobodných ovladačích povolil ovladač pro wifinu(předtím však v nabídce nebyl :( )

potom restart systému

opět příkaz sudo modprobe b43

objevuje se moje skrytá sít

pouze nastavím a vše jede v pořádku


Všem dík za pomoc

Ještě přidávám kód:

Kód: [Vybrat]
[    0.760921] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.762424] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 23
[    0.762431]   alloc irq_desc for 23 on node -1
[    0.762433]   alloc kstat_irqs on node -1
[    0.762445] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[LUB2] -> GSI 23 (level, low) -> IRQ 23
[    0.762465] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[    0.762469] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[    0.762514] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[    0.762540] ehci_hcd 0000:00:0b.1: debug port 1
[    0.762549] ehci_hcd 0000:00:0b.1: cache line size of 64 is not supported
[    0.762575] ehci_hcd 0000:00:0b.1: irq 23, io mem 0xdf5dfc00
[    0.807418] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[    0.807737] usb usb1: configuration #1 chosen from 1 choice
[    0.808202] hub 1-0:1.0: USB hub found
[    0.808214] hub 1-0:1.0: 8 ports detected
[    0.808439] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.809459] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 22
[    0.809464]   alloc irq_desc for 22 on node -1
[    0.809466]   alloc kstat_irqs on node -1
[    0.809478] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[LUB0] -> GSI 22 (level, low) -> IRQ 22
[    0.809494] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[    0.809498] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[    0.810131] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[    0.810167] ohci_hcd 0000:00:0b.0: irq 22, io mem 0xdf5de000
[    0.901010] usb usb2: configuration #1 chosen from 1 choice
[    0.901048] hub 2-0:1.0: USB hub found
[    0.901062] hub 2-0:1.0: 8 ports detected
[    0.901331] uhci_hcd: USB Universal Host Controller Interface driver
[    0.901437] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.907222] i8042.c: Detected active multiplexing controller, rev 1.1.
[    0.915449] ACPI: Battery Slot [BAT0] (battery present)
[    0.920502] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.923404] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.923455] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.923482] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.923517] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.923873] mice: PS/2 mouse device common for all mice
[    0.924848] rtc_cmos 00:02: RTC can wake from S4
[    0.924900] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    0.924939] rtc0: alarms up to one year, y3k, 114 bytes nvram
[    0.928124] device-mapper: uevent: version 1.0.3
[    0.928505] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.929387] device-mapper: multipath: version 1.1.0 loaded
[    0.929391] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.931728] EISA: Probing bus 0 at eisa.0
[    0.931739] Cannot allocate resource for EISA slot 2
[    0.931759] EISA: Detected 0 cards.
[    0.933391] cpuidle: using governor ladder
[    0.933462] cpuidle: using governor menu
[    0.933996] TCP cubic registered
[    0.934358] NET: Registered protocol family 10
[    0.934895] lo: Disabled Privacy Extensions
[    0.935267] NET: Registered protocol family 17
[    0.935307] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 3200+ processors (1 cpu cores) (version 2.20.00)
[    0.935347] powernow-k8:    0 : fid 0x8 (1600 MHz), vid 0x11
[    0.935351] powernow-k8:    1 : fid 0x0 (800 MHz), vid 0x18
[    0.935391] powernow-k8: ph2 null fid transition 0x8
[    0.935414] Using IPI No-Shortcut mode
[    0.935523] PM: Resume from disk failed.
[    0.935543] registered taskstats version 1
[    0.935925]   Magic number: 14:540:1003
[    0.935963] vc vcs: hash matches
[    0.935968] input input0: hash matches
[    0.935977] pnp 00:05: hash matches
[    0.936123] rtc_cmos 00:02: setting system clock to 2010-06-13 20:58:27 UTC (1276462707)
[    0.936128] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.936131] EDD information not available.
[    0.955206] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    1.304585] Freeing initrd memory: 7786k freed
[    1.397540] isapnp: No Plug & Play device found
[    1.397793] Freeing unused kernel memory: 656k freed
[    1.398403] Write protecting the kernel text: 4676k
[    1.398441] Write protecting the kernel read-only data: 1840k
[    1.419026] udev: starting version 151
[    1.452067] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    1.585840] usb 1-1: configuration #1 chosen from 1 choice
[    1.692439] pata_amd 0000:00:0d.0: version 0.4.1
[    1.692490] pata_amd 0000:00:0d.0: setting latency timer to 64
[    1.692635] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.693049] ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
[    1.693055]   alloc irq_desc for 18 on node -1
[    1.693058]   alloc kstat_irqs on node -1
[    1.693070] r8169 0000:02:00.0: PCI INT A -> Link[LNEA] -> GSI 18 (level, low) -> IRQ 18
[    1.693106] r8169 0000:02:00.0: setting latency timer to 64
[    1.693147]   alloc irq_desc for 27 on node -1
[    1.693149]   alloc kstat_irqs on node -1
[    1.693160] r8169 0000:02:00.0: irq 27 for MSI/MSI-X
[    1.693976] eth0: RTL8168b/8111b at 0xdc864000, 00:18:f3:38:e0:d2, XID 18000000 IRQ 27
[    1.695504] scsi0 : pata_amd
[    1.695678] scsi1 : pata_amd
[    1.697300] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.697304] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.705171] Initializing USB Mass Storage driver...
[    1.705264] scsi2 : SCSI emulation for USB Mass Storage devices
[    1.705403] usbcore: registered new interface driver usb-storage
[    1.705407] USB Mass Storage support registered.
[    1.705502] usb-storage: device found at 2
[    1.705504] usb-storage: waiting for device to settle before scanning
[    1.860378] ata1.00: ATAPI: HL-DT-ST DVDRAM GMA-4082N, HJ02, max UDMA/33
[    1.860412] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000c600) ACPI=0x701f (60:900:0x11)
[    1.876330] ata1.00: configured for UDMA/33
[    1.885624] scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GMA-4082N HJ02 PQ: 0 ANSI: 5
[    1.897417] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.897421] Uniform CD-ROM driver Revision: 3.20
[    1.897678] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.897814] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.944076] usb 2-2: new low speed USB device using ohci_hcd and address 2
[    2.060546] ata2.00: ATA-6: ST98823A, 3.06, max UDMA/100
[    2.060551] ata2.00: 156301488 sectors, multi 16: LBA48
[    2.060580] ata2: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc000c600) ACPI=0x3f01f (20:900:0x11)
[    2.076481] ata2.00: configured for UDMA/100
[    2.076576] scsi 1:0:0:0: Direct-Access     ATA      ST98823A         3.06 PQ: 0 ANSI: 5
[    2.076726] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    2.076941] sd 1:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    2.076997] sd 1:0:0:0: [sda] Write Protect is off
[    2.077001] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.077031] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.077186]  sda: sda1 sda2 < >
[    2.110806] sd 1:0:0:0: [sda] Attached SCSI disk
[    2.115296] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 17
[    2.115303]   alloc irq_desc for 17 on node -1
[    2.115306]   alloc kstat_irqs on node -1
[    2.115319] ohci1394 0000:04:01.1: PCI INT B -> Link[LNKC] -> GSI 17 (level, low) -> IRQ 17
[    2.147887] usb 2-2: configuration #1 chosen from 1 choice
[    2.165744] usbcore: registered new interface driver hiddev
[    2.170085] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[df7ff000-df7ff7ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    2.177447] input: HID 062a:0000 as /devices/pci0000:00/0000:00:0b.0/usb2/2-2/2-2:1.0/input/input6
[    2.177670] generic-usb 0003:062A:0000.0001: input,hidraw0: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:0b.0-2/input0
[    2.177700] usbcore: registered new interface driver usbhid
[    2.177815] usbhid: v2.6:USB HID core driver
[    3.452192] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800036510e8]
[    6.704283] usb-storage: device scan complete
[    6.705905] scsi 2:0:0:0: Direct-Access     WD       1600BEV External 1.05 PQ: 0 ANSI: 4
[    6.706873] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    6.707614] sd 2:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    6.709772] sd 2:0:0:0: [sdb] Write Protect is off
[    6.709778] sd 2:0:0:0: [sdb] Mode Sense: 21 00 00 00
[    6.709782] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    6.712759] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    6.712763]  sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 >
[    6.762789] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    6.762796] sd 2:0:0:0: [sdb] Attached SCSI disk
[    7.278970] EXT4-fs (sdb5): mounted filesystem with ordered data mode
[   17.337362] Adding 1299448k swap on /dev/sdb6.  Priority:-1 extents:1 across:1299448k
[   17.592308] udev: starting version 151
[   17.797674] ACPI: resource nForce2_smbus [0x600-0x63f] conflicts with ACPI region SMRG [0x600-0x60f]
[   17.797678] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   17.797682] nForce2_smbus 0000:00:0a.1: Error probing SMB1.
[   17.797783] i2c i2c-0: nForce2 SMBus adapter at 0x700
[   17.805420] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[   17.847642] vga16fb: initializing
[   17.847647] vga16fb: mapped to 0xc00a0000
[   17.847722] fb0: VGA16 VGA frame buffer device
[   18.053411] Linux agpgart interface v0.103
[   18.162567] Disabling lock debugging due to kernel taint
[   18.185127] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
[   18.216821] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input7
[   18.216974] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   18.294607] usbcore: registered new interface driver ndiswrapper
[   19.126408] type=1505 audit(1276462725.687:2):  operation="profile_load" pid=637 name="/sbin/dhclient3"
[   19.126755] type=1505 audit(1276462725.687:3):  operation="profile_load" pid=637 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   19.126951] type=1505 audit(1276462725.687:4):  operation="profile_load" pid=637 name="/usr/lib/connman/scripts/dhclient-script"
[   21.015082] asus_laptop: Asus Laptop Support version 0.42
[   21.017448] asus_laptop: Error calling BSTS
[   21.017452] asus_laptop:   A6M model detected
[   21.026747] sdhci: Secure Digital Host Controller Interface driver
[   21.026752] sdhci: Copyright(c) Pierre Ossman
[   21.282486] lp: driver loaded but no devices found
[   21.290578] input: Asus Laptop extra buttons as /devices/virtual/input/input8
[   21.292054] Registered led device: asus::mail
[   21.310409] ACPI: PCI Interrupt Link [LNEC] enabled at IRQ 16
[   21.310417]   alloc irq_desc for 16 on node -1
[   21.310420]   alloc kstat_irqs on node -1
[   21.310432] nvidia 0000:00:05.0: PCI INT A -> Link[LNEC] -> GSI 16 (level, low) -> IRQ 16
[   21.310441] nvidia 0000:00:05.0: setting latency timer to 64
[   21.310446] vgaarb: device changed decodes: PCI:0000:00:05.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   21.311644] NVRM: loading NVIDIA UNIX x86 Kernel Module  195.36.24  Thu Apr 22 09:18:20 PDT 2010
[   21.427568] yenta_cardbus 0000:04:01.0: CardBus bridge found [1043:1367]
[   21.554364] yenta_cardbus 0000:04:01.0: ISA IRQ mask 0x0cb8, PCI irq 19
[   21.554368] yenta_cardbus 0000:04:01.0: Socket status: 30000006
[   21.554373] pci_bus 0000:04: Raising subordinate bus# of parent bus (#04) from #05 to #08
[   21.554382] yenta_cardbus 0000:04:01.0: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
[   21.554387] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xe000-0xefff: clean.
[   21.554628] yenta_cardbus 0000:04:01.0: pcmcia: parent PCI bridge Memory window: 0xdf700000 - 0xdfffffff
[   21.554632] yenta_cardbus 0000:04:01.0: pcmcia: parent PCI bridge Memory window: 0xdb000000 - 0xdcffffff
[   21.704973] sdhci-pci 0000:04:01.2: SDHCI controller found [1180:0822] (rev 17)
[   21.705379] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
[   21.705385] sdhci-pci 0000:04:01.2: PCI INT C -> Link[LNKD] -> GSI 19 (level, low) -> IRQ 19
[   21.707441] Registered led device: mmc0::
[   21.708510] mmc0: SDHCI controller on PCI [0000:04:01.2] using PIO
[   21.780729] Console: switching to colour frame buffer device 80x30
[   22.006784] EXT4-fs (sdb7): mounted filesystem with ordered data mode
[   22.030741] Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[   22.070101] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input9
[   22.568810] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[   22.569958] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[   22.570453] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: excluding 0x828-0x82f 0x840-0x85f 0x870-0x877
[   22.570767] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[   22.571359] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[   22.750707] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[   22.750715]   alloc irq_desc for 21 on node -1
[   22.750718]   alloc kstat_irqs on node -1
[   22.750741] HDA Intel 0000:00:10.1: PCI INT B -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[   22.750753] hda_intel: Disable MSI for Nvidia chipset
[   22.750800] HDA Intel 0000:00:10.1: setting latency timer to 64
[   23.581676] r8169: eth0: link down
[   23.581779] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.684231] type=1505 audit(1276462730.247:5):  operation="profile_load" pid=818 name="/usr/share/gdm/guest-session/Xsession"
[   23.686584] type=1505 audit(1276462730.247:6):  operation="profile_replace" pid=880 name="/sbin/dhclient3"
[   23.686949] type=1505 audit(1276462730.247:7):  operation="profile_replace" pid=880 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   23.687155] type=1505 audit(1276462730.247:8):  operation="profile_replace" pid=880 name="/usr/lib/connman/scripts/dhclient-script"
[   23.758733] hda_codec: ALC660: BIOS auto-probing.
[   23.817188] type=1505 audit(1276462730.379:9):  operation="profile_load" pid=882 name="/usr/bin/evince"
[   23.823435] type=1505 audit(1276462730.383:10):  operation="profile_load" pid=882 name="/usr/bin/evince-previewer"
[   23.827690] type=1505 audit(1276462730.387:11):  operation="profile_load" pid=882 name="/usr/bin/evince-thumbnailer"
[   23.972122] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input10
[   25.065589] ppdev: user-space parallel port driver
michal@michal-laptop:~$ lspci -vnnk
00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f3] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0 [10de:02fa] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1 [10de:02fe] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5 [10de:02f8] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4 [10de:02f9] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0

00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3 [10de:027f] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2 [10de:027e] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: 66MHz, fast devsel

00:02.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fc] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:03.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fd] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df600000-df6fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:04.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge [10de:02fb] (rev a1)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:05.0 VGA compatible controller [0300]: nVidia Corporation C51 [GeForce Go 6100] [10de:0247] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1382]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at dd000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at df5e0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidia-current, nvidiafb, nouveau

00:09.0 RAM memory [0500]: nVidia Corporation MCP51 Host Bridge [10de:0270] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0

00:0a.1 SMBus [0c05]: nVidia Corporation MCP51 SMBus [10de:0264] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: 66MHz, fast devsel, IRQ 5
I/O ports at 0600 [size=64]
I/O ports at 0700 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2

00:0a.3 Co-processor [0b40]: nVidia Corporation MCP51 PMU [10de:0271] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 10
Memory at df580000 (32-bit, non-prefetchable) [size=256K]

00:0b.0 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026d] (rev a3) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
Memory at df5de000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

00:0b.1 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026e] (rev a3) (prog-if 20)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at df5dfc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

00:0d.0 IDE interface [0101]: nVidia Corporation MCP51 IDE [10de:0265] (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
Kernel modules: pata_amd

00:10.0 PCI bridge [0604]: nVidia Corporation MCP51 PCI Bridge [10de:026f] (rev a2) (prog-if 01)
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=08, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: df700000-dfffffff
Prefetchable memory behind bridge: db000000-dcffffff
Capabilities: <access denied>

00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio [10de:026c] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
Memory at df5d8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Flags: fast devsel
Capabilities: <access denied>

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Flags: fast devsel

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Flags: fast devsel

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Flags: fast devsel
Kernel driver in use: k8temp
Kernel modules: k8temp

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:11f5]
Flags: bus master, fast devsel, latency 0, IRQ 27
I/O ports at d800 [size=256]
Memory at df6ff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at df6e0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

04:01.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b3)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 168, IRQ 19
Memory at df700000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 0000e400-0000e4ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket

04:01.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] (rev 08) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at df7ff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: firewire-ohci, ohci1394

04:01.2 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 17)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at df7ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci

04:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 08)
Subsystem: ASUSTeK Computer Inc. Device [1043:1367]
Flags: medium devsel, IRQ 5
Memory at df7ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

04:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:120f]
Flags: bus master, fast devsel, latency 64, IRQ 10
Memory at df7fc000 (32-bit, non-prefetchable) [size=8K]
Kernel modules: ssb

michal@michal-laptop:~$ sudo modprobe b43
[sudo] password for michal:
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
michal@michal-laptop:~$
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu Broadcom 4318? [vyřešeno - napůl]
« Odpověď #18 kdy: 14 Června 2010, 03:19:53 »
No jeden problém tu přece jen je,po restartu musím znova zadat:
sudo modprobe b43
teprve pak se objeví klíčenka,to není moc pohodlné :(
Neberte život příliš vážně, stejně z něho nevyváznete živý.

Yontalcar

  • Stálý člen
  • **
  • Příspěvků: 833
  • Semper fidelis
Re: Je to opravdu problém rozjet wifinu Broadcom 4318? [vyřešeno - napůl]
« Odpověď #19 kdy: 14 Června 2010, 05:52:50 »
připiš "b43" na konec souboru /etc/modules
NB: ASUS X53U - AMD Brazos E450; Debian GNU/Linux Sid amd64 (KDE 4.14)
Jen dvě věci jsou nekonečné - vesmír a lidská hloupost. Tím prvním si ovšem nejsem tak jist. - Albert Einstein

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu Broadcom 4318? [vyřešeno - napůl]
« Odpověď #20 kdy: 14 Června 2010, 11:31:51 »
připiš "b43" na konec souboru /etc/modules

Dík,ale v tom se moc nevyznám,nebyl by na to nějaký příkaz?
Neberte život příliš vážně, stejně z něho nevyváznete živý.

compaq

  • Závislák
  • ***
  • Příspěvků: 2445
  • Díky všem za rady a tipy.
Re: Je to opravdu problém rozjet wifinu Broadcom 4318? [vyřešeno - napůl]
« Odpověď #21 kdy: 14 Června 2010, 11:43:40 »
připiš "b43" na konec souboru /etc/modules

Dík,ale v tom se moc nevyznám,nebyl by na to nějaký příkaz?

Citace
sudo gedit /etc/modules

a tam to připsat nakonec a uložit
Pokud vám vaše holka či manželka funguje jak má, neměňte jí za mladší, zaděláte si na problém. Stejně to dělejte i s Ubuntu.

Michal66

  • Návštěvník
  • Příspěvků: 68
Re: Je to opravdu problém rozjet wifinu Broadcom 4318? [vyřešeno - napůl]
« Odpověď #22 kdy: 14 Června 2010, 12:00:55 »
připiš "b43" na konec souboru /etc/modules

Dík,ale v tom se moc nevyznám,nebyl by na to nějaký příkaz?

Citace
sudo gedit /etc/modules

a tam to připsat nakonec a uložit

Dík moc všem kteří pomohli,teď už je to ok!
Neberte život příliš vážně, stejně z něho nevyváznete živý.

 

Provoz zaštiťuje spolek OpenAlt.