xsane nepracuje správne

[gogo21]

Nainštaloval som 10.4 32bit. Zo synaptiku som stiahol a nainštaloval xsane. Pri zapnutí scanera (Epson stylus CX3650, multifunkčné zariadenie) a spustení xsane sa zobrazí hlásenie: "chyba počas CMS konverzíí: Nie je možné otvoriť ICM profile scanera: Zatvoriť". Xsane som odinštaloval a preinštaloval niekoľko krát ale nič sa nezmenilo. V predchádzajúcej verzii 9.04 scaner pracoval bez závad. Taktiež aj teraz vo winxp pracuje bez závad. Čo je to CMS konverzia a ICM profile?   

[arrange]

?Můžeš prosím tě zapnout scanner, otevřít Terminál, a dát tu výstup z příkazů

Kód: [Vybrat]

sane-find-scanner
scanimage -L


[gogo21]

# sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.

  # No USB scanners found. If you expected something different, make sure that
  # you have loaded a kernel driver for your USB host controller and have setup
  # the USB system correctly. See man sane-usb for details.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.

  # You may want to run this program as root to find all devices. Once you
  # found the scanner devices, be sure to adjust access permissions as
  # necessary.
rudo@rudo-desktop:~$ scanimage -L
device `epson2:libusb:002:004' is a Epson CX3600 flatbed scanner

[arrange]

Ještě

Kód: [Vybrat]

sudo sane-find-scanner
lsusb

[gogo21]

 # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x04b8 [EPSON], product=0x080e [USB MFP]) at libusb:002:005
  # Your USB scanner was (probably) detected. It may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.
rudo@rudo-desktop:~$ lsusb
Bus 002 Device 005: ID 04b8:080e Seiko Epson Corp. CX-3500/3600/3650 MFP
Bus 002 Device 002: ID 093a:2510 Pixart Imaging, Inc. Hama Optical Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 058f:6377 Alcor Micro Corp. Multimedia Card Reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

[arrange]

Zkus skenovat z příkazové řádky

Kód: [Vybrat]

scanimage -v > /tmp/test.pnm
Jestli skenování proběhlo, mrkni se na ten obrázek (/tmp/test.pnm). Je OK?

[gogo21]

nascanovalo OK

[arrange]

Zkus v xsane najet do Nastavení a pohrát si s volbou enable color management (vypnout nebo zapnout, pak zkusit skenovat).
https://answers.launchpad.net/ubuntu/+source/xsane/+question/65736

[gogo21]

Vyriešené. Bolo tam zafajkované "Povoliť správu farieb". Keď som odfajkoval, všetko začalo pracovať bez problémov. Ďakujem za radu.

[arrange]

Slováci mají "Povoliť správu farieb" přeložené a Česi nie?! To je nějaký binec!