Sledování HW (notebook)

[MaS]

Dobrý den,
mám notebook MSI CX600 a snažím se sprovoznit HW monitoring.
Nainstaloval jsem lm-sensors, ale našlo mi to pouze senzory teploty procesoru a nějaký temp1.
Když jsem chtěl pomocí sensors-detect zjistit nějaký další čidla, tak mi to vypsalo, že tam něco je (SMSC chip s ID 0x34, ale nějakej nestandartní).
Tady je výpis:

Kód: [Vybrat]

# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: Micro-Star International CX600 (laptop)
# Board: MICRO-STAR INT'L CO., LTD MS-1682

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
Intel Core family thermal sensor...                         Success!
    (driver `coretemp')
Intel Atom thermal sensor...                                No
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     Yes
Found unknown non-standard chip with ID 0x34

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Sorry, no supported PCI bus adapters found.
Module i2c-dev loaded successfully.

Now follows a summary of the probes I have just done.
Jak zjistím z toho ID jméno chipu (jestli tam vůbec někde je), abych věděl co mám hledat na netu? Popřípadě jak dál postupovat, pokud to chci nějak rozchodit?

Dík Marek

[jenda93]

Je to asi špatné. Obyčejně se tam po tomto řádku:

Kód: [Vybrat]

Do you want to probe the I2C/SMBus adapters now? (YES/no): y

objeví zpráva

Kód: [Vybrat]

Using Driver ....

a výpis dále pokračuje. Hledaný název je potom až skoro na konci. Příklad jenom pro ilustraci:

Kód: [Vybrat]

#----cut here----
# Chip drivers
dme1737
#----cut here----


[MaS]

Jsem to ale ...!
Nezkoupíroval jsem celý výpis, na konci má být ještě

Kód: [Vybrat]

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `coretemp':
  * Chip `Intel Core family thermal sensor' (confidence: 9)

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)y
Successful!

Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.

Unloading i2c-dev... OK
(jak jste psal)

Problém je ale v tom, že to našlo jen sensory na procesoru - já bych potřeboval i čidla ze zakl. desky, větráky,...
Já nevim, nejde nějak zjistit jméno toho čipu a pak třeba manuálně doinstalovat drivery? Nebo tak něco?
Nebo když, to lm-sensors nenajde, tak se s tim můžu rozloučit?
Marek