lpr > bricscad

[Bum]

Ahoj mam problem s prikazom lpr
tvari sa ze tlaci subor ale PDF sa nikde neobjavi
potreboval by som ho rozbehat, lebo sa mi zda, ze bricscad vyuziva prave lpr na tlacenie.
toto sa objavi v terminali ked spustim tlacenie

Kód: [Vybrat]

DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::refreshLists got validator
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::refreshLists got devicelist
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes got config name
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes changed active device
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes got canonical media name
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::refreshLists done updateActiveDeviceMediaIndexes
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::refreshLists end
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes got config name
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes changed active device
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes got config name
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes changed active device
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes got config name
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes changed active device
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes got canonical media name
DWGdirect warning: priority={1} OdDbPlotSettingsValidatorImpl::updateActiveDeviceMediaIndexes changed active media
usage: lpr [-cdfghlmnpqrstv] [-#num] [-1234 font] [-C class] [-i [numcols]]
[-J job] [-Pprinter] [-T title] [-U user] [-wnum] [name ...]


cat /var/log/cups/error_log

Kód: [Vybrat]

Avahi client failed, closing client to allow a clean restart
toto sa zda byt vyriesene.
cat /var/log/lpr.log

Kód: [Vybrat]

Jan 17 18:07:52 bum udev-configure-printer: add /module/lp
Jan 17 18:07:52 bum udev-configure-printer: Failed to get parent
Jan 17 18:07:56 bum lpd[1793]: restarted

toto je asi iny problem

cat /var/log/syslog

Kód: [Vybrat]

Jan 17 20:40:07 bum dbus[1404]: [system] Activating service name='org.opensuse.CupsPkHelper.Mechanism' (using servicehelper)
Jan 17 20:40:07 bum dbus[1404]: [system] Successfully activated service 'org.opensuse.CupsPkHelper.Mechanism'
Jan 17 20:40:08 bum ntpd_intres[1866]: recv() fails: No route to host

[pacholik]

BrisCad nemám, ale

Kód: [Vybrat]

usage: lpr [-cdfghlmnpqrstv] [-#num] [-1234 font] [-C class] [-i [numcols]]
[-J job] [-Pprinter] [-T title] [-U user] [-wnum] [name ...]značí chybnou syntaxi, chyba bude v BrisCadu

[Bum]

Briscad teraz nie je celkom ten hlavny problem.
ide o to ze to lpr fakt netlaci. ma predvolenu tlaciaren PDF
ked zadam lpr b.txt nespravi vodec pdf

pokial mi tlacilo na ubuntu lpr isiel aj bricscad v poriadku

[Bum]

Dakujem za pomoc.

nasiel som na jednej stranke ze mam mat nainstalovane nie lpr, ale cups-bsd.

Uz to funguje

Vyriesene.