Dobry den, mel bych dotaz ohledne rychlosti sitove karty.
am dve sitove karty, podle meho by obe mely mit rychlost 1GBit s tim, ze obe se nadetekuji jako 100MB. Je možné toto nastvaveni zmenit, pripadne jak overit zvyseni rychlosti.
Jedna se o desku gigabite GA-Z77X-UD5H s integrovanymi
1 x Atheros GbE LAN chip (10/100/1000 Mbit) (LAN1)
1 x Intel GbE LAN chip (10/100/1000 Mbit) (LAN2)
Nebo si sitovka overuje rychlost pri instalaci. Na jedne sitoivce je kamerovy system (vse 1GB) na druhe internet. V siti je mozne, ze nektere PC ve vnitrni siti maji rychlost 100MB, ale vetsina 1GB. Lze zajistit, aby rychlost byla vetsi?
Dekuji.
Hyp
eth0 Link encap:Ethernet HWadr 90:2b:34:30:71:d4
inet adr:192.168.1.110 Všesměr:192.168.1.255 Maska:255.255.255.0
inet6-adr: fe80::922b:34ff:fe30:71d4/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:813023314 errors:0 dropped:0 overruns:0 frame:0
TX packets:529792769 errors:0 dropped:0 overruns:0 carrier:1
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 2756364292 (2.7 GB) Odesláno bajtů: 2440027256 (2.4 GB)
eth1 Link encap:Ethernet HWadr 50:e5:49:ef:ad:75
inet adr:10.0.0.145 Všesměr:10.0.0.255 Maska:255.255.255.0
inet6-adr: fe80::52e5:49ff:feef:ad75/64 Rozsah:Linka
AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST MTU:1500 Metrika:1
RX packets:1510977 errors:0 dropped:0 overruns:0 frame:0
TX packets:1224054 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:1000
Přijato bajtů: 1177073832 (1.1 GB) Odesláno bajtů: 107911015 (107.9 MB)
ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Cannot get wake-on-lan settings: Operation not permitted
Current message level: 0x0000003f (63)
drv probe link timer ifdown ifup
Cannot get link status: Operation not permitted
ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 2
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Cannot get wake-on-lan settings: Operation not permitted
Current message level: 0x00000007 (7)
drv probe link
Cannot get link status: Operation not permitted