Mrtvá myš po probuzení

[Mariocz]

Ahoj,

předmět topicu asi říká vše. Občas po probuzení z memsleepu mýš nereaguje, nesvítí optika. Nestává se to vždycky a nenašel jsem konfiguraci ve které se už myška nevrátí.

Jsem linux noob tak nevím co za výpisy vám poslat. Řekněte si co by jste chtěli vidět.

Díky

dmesg |tail -n 190 |grep usb
(od [26970.237508] je to log vypojení a zapojení USB myšky. Potom šlape v pohodě)

Kód: [Vybrat]

[26960.168884] PM: resume of drv:usb dev:3-1 complete after 123.659 msecs
[26960.168904] PM: resume of drv:usb dev:3-4 complete after 123.507 msecs
[26960.168932] PM: resume of drv:usb dev:3-3 complete after 123.592 msecs
[26960.216794] PM: resume of drv:usb dev:1-1.3 complete after 171.309 msecs
[26960.241258] PM: resume of drv:usbhid dev:3-1:1.0 complete after 196.116 msecs
[26960.280978] usb 3-4: reset full-speed USB device number 4 using xhci_hcd
[26960.298687] btusb 3-4:1.0: no reset_resume for driver btusb?
[26960.298689] btusb 3-4:1.1: no reset_resume for driver btusb?
[26960.298852] PM: resume of drv:usb dev:3-4:1.0 complete after 253.610 msecs
[26960.298854] PM: resume of drv:usb dev:3-4:1.1 complete after 253.565 msecs
[26960.298862] PM: resume of drv:usb dev:3-4:1.2 complete after 253.540 msecs
[26960.298881] PM: resume of drv:usb dev:3-4:1.3 complete after 253.526 msecs
[26960.408825] usb 3-3: reset high-speed USB device number 3 using xhci_hcd
[26960.496503] usb 1-1.3: reset high-speed USB device number 3 using ehci_hcd
[26970.237508] usb 3-1: USB disconnect, device number 2
[26971.518210] usb 3-1: new low-speed USB device number 5 using xhci_hcd
[26971.538256] usb 3-1: New USB device found, idVendor=04f3, idProduct=0230
[26971.538263] usb 3-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[26971.538268] usb 3-1: Product: USB+PS/2 Optical Mouse
[26971.538633] usb 3-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[26971.541111] input: USB+PS/2 Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.0/input/input14
[26971.541518] hid-generic 0003:04F3:0230.0002: input,hidraw0: USB HID v1.11 Mouse [USB+PS/2 Optical Mouse] on usb-0000:00:14.0-1/input0

lsusb

Kód: [Vybrat]

Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 005: ID 04f3:0230 Elan Microelectronics Corp. 3D Optical Mouse
Bus 003 Device 003: ID 5986:0295 Acer, Inc
Bus 003 Device 004: ID 0489:e032 Foxconn / Hon Hai
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 0bda:0139 Realtek Semiconductor Corp. Card reader


[Rover623]

Nestačilo by tu myš po probuzení jen resetnout, pomocí usb_modeswitch, tedy něco takového zadat do terminálu

Kód: [Vybrat]

sudo usb_modeswitch -R -v 04f3 -p 0230 pokud to pomůže napíšu ti skript který to automatizuje

[Mariocz]

Až se to znovu stane tak to zkusím a dám vědět. zatím díky

edit:

Znovu se opakovala stejná situace a mám takový dojem, že se tak děje po uspání které nastane automaticky při neaktivitě nastavené v System Settings -> Power. Když jsem ho párkrát zkusil uspat a probrat, myš vždy zafungovala.

Po pokusu o resetnutí to failne s tímto výstupem

Kód: [Vybrat]

Looking for default devices ...
   found matching product ID
   adding device
 Found device in default mode, class or configuration (1)
Accessing device 010 on bus 003 ...
Getting the current device configuration ...
 OK, got current device configuration (1)
Using first interface: 0x00
Error: message endpoint not given or found. Aborting.
lsusb s mrtvou myškou dává stejný výstup jako v prvním postu (tedy myš je tam furt uvedená na BUS 003.

ještě jednou dmesg | tail 120

Kód: [Vybrat]

[72873.474408] Booting Node 0 Processor 1 APIC 0x1
[72873.484661] Initializing CPU#1
[72873.488595] CPU1 is up
[72873.488658] Booting Node 0 Processor 2 APIC 0x2
[72873.498887] Initializing CPU#2
[72873.502835] CPU2 is up
[72873.502891] Booting Node 0 Processor 3 APIC 0x3
[72873.513119] Initializing CPU#3
[72873.517130] CPU3 is up
[72873.520638] ACPI: Waking up from system sleep state S3
[72873.737996] xhci_hcd 0000:00:14.0: wake-up capability disabled by ACPI
[72873.738102] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[72873.738345] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[72873.738784] PM: noirq resume of devices complete after 0.921 msecs
[72873.738883] PM: early resume of devices complete after 0.077 msecs
[72873.738967] xhci_hcd 0000:00:14.0: setting latency timer to 64
[72873.738972] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[72873.739039] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[72873.739048] ahci 0000:00:1f.2: setting latency timer to 64
[72873.739059] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[72873.739060] mei 0000:00:16.0: irq 44 for MSI/MSI-X
[72873.739084] r8169 0000:03:00.0: wake-up capability disabled by ACPI
[72873.739371] [drm] nouveau 0000:01:00.0: We're back, enabling device...
[72873.739385] nouveau 0000:01:00.0: power state changed by ACPI to D0
[72873.739386] i915 0000:00:02.0: setting latency timer to 64
[72873.739388] nouveau 0000:01:00.0: power state changed by ACPI to D0
[72873.739391] nouveau 0000:01:00.0: power state changed by ACPI to D0
[72873.739394] nouveau 0000:01:00.0: power state changed by ACPI to D0
[72873.739400] [drm] nouveau 0000:01:00.0: POSTing device...
[72873.739401] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0x7954
[72873.745012] mei 0000:00:16.0: wd: failed to find the client
[72873.776693] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[72873.799832] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0x7FB0
[72873.826660] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0x9245
[72873.826664] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0x9249
[72873.826717] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0x9350
[72873.826718] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0x93B5
[72873.846548] [drm] nouveau 0000:01:00.0: Restoring GPU objects...
[72873.857483] PM: resume of drv:hub dev:3-0:1.0 complete after 118.300 msecs
[72873.857491] PM: resume of drv:usb dev:3-3 complete after 117.621 msecs
[72873.857502] PM: resume of drv:usb dev:3-4 complete after 117.575 msecs
[72873.857508] PM: resume of drv:usb dev:3-1 complete after 117.037 msecs
[72873.857516] PM: resume of drv: dev:ep_81 complete after 118.321 msecs
[72873.857523] PM: resume of drv: dev:ep_00 complete after 118.325 msecs
[72873.902549] [drm] nouveau 0000:01:00.0: Reinitialising engines...
[72873.903008] [drm] nouveau 0000:01:00.0: Restoring mode...
[72873.904546] [drm] nouveau 0000:01:00.0: no native mode, forcing panel scaling
[72873.917411] PM: resume of drv:hub dev:1-1:1.0 complete after 178.231 msecs
[72873.917415] PM: resume of drv: dev:ep_00 complete after 178.213 msecs
[72873.917418] PM: resume of drv:usb dev:1-1.3 complete after 177.274 msecs
[72873.917423] PM: resume of drv: dev:ep_81 complete after 178.233 msecs
[72873.926302] PM: resume of drv:net dev:eth0 complete after 142.869 msecs
[72873.929835] PM: resume of drv: dev:ep_00 complete after 189.351 msecs
[72873.929860] PM: resume of drv:usbhid dev:3-1:1.0 complete after 189.468 msecs
[72873.929865] PM: resume of drv: dev:ep_81 complete after 189.440 msecs
[72873.969528] usb 3-3: reset high-speed USB device number 3 using xhci_hcd
[72873.992983] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f6a41d80
[72873.993798] PM: resume of drv:uvcvideo dev:3-3:1.1 complete after 254.068 msecs
[72873.993800] PM: resume of drv: dev:ep_00 complete after 254.058 msecs
[72873.993815] PM: resume of drv:uvcvideo dev:3-3:1.0 complete after 254.109 msecs
[72873.993847] PM: resume of drv: dev:ep_81 complete after 254.129 msecs
[72874.065281] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[72874.097519] usb 3-4: reset full-speed USB device number 4 using xhci_hcd
[72874.102735] ata3.00: configured for UDMA/100
[72874.115176] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f693fc00
[72874.115178] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f693fc58
[72874.115179] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f693fc2c
[72874.115180] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f6a5308c
[72874.115181] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f6a53060
[72874.115182] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f6a532cc
[72874.115183] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep f6a532a0
[72874.115555] btusb 3-4:1.0: no reset_resume for driver btusb?
[72874.115556] btusb 3-4:1.1: no reset_resume for driver btusb?
[72874.115729] PM: resume of drv:usb dev:3-4:1.0 complete after 376.121 msecs
[72874.115731] PM: resume of drv:usb dev:3-4:1.3 complete after 375.862 msecs
[72874.115735] PM: resume of drv:usb dev:3-4:1.1 complete after 376.025 msecs
[72874.115742] PM: resume of drv:usb dev:3-4:1.2 complete after 375.912 msecs
[72874.115745] PM: resume of drv: dev:ep_02 complete after 376.103 msecs
[72874.115746] PM: resume of drv: dev:ep_83 complete after 376.030 msecs
[72874.115748] PM: resume of drv: dev:ep_81 complete after 376.127 msecs
[72874.115749] PM: resume of drv: dev:ep_82 complete after 376.119 msecs
[72874.115750] PM: resume of drv: dev:ep_00 complete after 375.873 msecs
[72874.115751] PM: resume of drv: dev:ep_03 complete after 375.934 msecs
[72874.115758] PM: resume of drv: dev:ep_04 complete after 375.905 msecs
[72874.115764] PM: resume of drv: dev:ep_84 complete after 375.922 msecs
[72874.141220] PM: resume of drv:scsi dev:host2 complete after 402.022 msecs
[72874.141230] PM: resume of drv:scsi_host dev:host2 complete after 402.023 msecs
[72874.141232] PM: resume of drv:scsi dev:target2:0:0 complete after 401.876 msecs
[72874.141239] PM: resume of drv:sr dev:2:0:0:0 complete after 401.762 msecs
[72874.141253] PM: resume of drv:scsi_device dev:2:0:0:0 complete after 401.762 msecs
[72874.185289] usb 1-1.3: reset high-speed USB device number 3 using ehci_hcd
[72874.281412] PM: resume of drv: dev:ep_00 complete after 541.676 msecs
[72874.281442] PM: resume of drv:rts5139 dev:1-1.3:1.0 complete after 541.744 msecs
[72874.281476] PM: resume of drv:scsi dev:host6 complete after 541.731 msecs
[72874.281478] PM: resume of drv: dev:ep_82 complete after 541.769 msecs
[72874.281487] PM: resume of drv: dev:ep_01 complete after 541.790 msecs
[72874.281489] PM: resume of drv: dev:ep_83 complete after 541.766 msecs
[72874.281490] PM: resume of drv:scsi_host dev:host6 complete after 541.734 msecs
[72874.281495] PM: resume of drv:scsi dev:target6:0:0 complete after 541.652 msecs
[72874.281504] PM: resume of drv:sd dev:6:0:0:0 complete after 541.650 msecs
[72874.281535] PM: resume of drv:scsi_device dev:6:0:0:0 complete after 541.668 msecs
[72876.518096] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[72876.777752] ata1.00: configured for UDMA/133
[72876.793810] PM: resume of drv:scsi dev:host0 complete after 3058.069 msecs
[72876.793816] PM: resume of drv:ata_port dev:ata1 complete after 2871.215 msecs
[72876.793821] PM: resume of drv:scsi_host dev:host0 complete after 3058.076 msecs
[72876.793823] PM: resume of drv:scsi dev:target0:0:0 complete after 3057.982 msecs
[72876.793830] PM: resume of drv:sd dev:0:0:0:0 complete after 3057.977 msecs
[72876.793834] sd 0:0:0:0: [sda] Starting disk
[72876.801198] PM: resume of drv:scsi_device dev:0:0:0:0 complete after 3065.292 msecs
[72876.801286] PM: resume of devices complete after 3066.363 msecs
[72876.801560] PM: resume devices took 3.064 seconds
[72876.801672] PM: Finishing wakeup.
[72876.801674] Restarting tasks ... done.
[72876.830126] video LNXVIDEO:00: Restoring backlight state
[72876.831051] video LNXVIDEO:01: Restoring backlight state
[72876.852201] Bluetooth: can't load firmware, may not work correctly
[72877.248078] r8169 0000:03:00.0: eth0: link down
[72986.723603] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 2 with no TDs queued?
[72986.723612] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 2 ep 0 with no TDs queued?


[Mariocz]

Bump.

Nejspíš příspěvek editem není označeńej jako nepřečtenej tak to napravuju. Příště se polepším a hodím to do odpovědi.

[Rover623]

Nápadně to vypadá, že se nenatáhne modul, zkus tohle

Kód: [Vybrat]

sudo modprobe xhci_hcd a případně potom znovu ten reset.

Jo a hodil by se výstup z

Kód: [Vybrat]

uname -a pro verzi jádra a

Kód: [Vybrat]

lsb_release -a pro verzi systému.

A taky výstup z

Kód: [Vybrat]

lsmod hned potom co to znovu zlehne, to by mělo potvrdit moji domněnku, že se nenatáhne potřebný modul